Download or read book Evaluation of Conventional and Alternative Sanitation Technologies Using the Life Cycle Assessment Approach written by Chirjiv Kaur Anand and published by . This book was released on 2013 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Most of our drinking water and wastewater infrastructure are at the end of their useful life facing significant deterioration, causing leaks and water losses. These losses are a waste of both energy and water, considering both water and wastewater treatment systems are very energy intensive. In order to deal with the urban water infrastructure issues, EPA has listed out the following goals: asset management, water and energy efficiency, infrastructure financing, price of water services and alternative technologies assessment. This dissertation addresses two of EPA's goals, water and energy efficiency and alternative technologies assessment. Three approaches were taken to address these goals. In the first approach, the life cycle energy demand for water and wastewater studies were reviewed from literature to understand the energy requirements of these systems and propose a benchmark energy demand. System boundaries, data collection and reporting, type of LCA used, were identified as the factors that influence the total energy use and energy use reporting. Energy use data of water and wastewater treatment systems have been compiled to obtain ranges of 2.8 x 10-06 - 4.8 x 10-03 kWh per L and 2.8 x 10-09 to 1.32 x 10-02 kWh per L respectively. From the details obtained from literature, energy use ranges for specific processes related to water and wastewater could not be obtained due to lack of appropriate data reporting. Development of an appropriate data reporting procedure for water and wastewater treatment life cycle assessments is required to be able to collect, use and analyze this data. In the second approach, alternative technologies were assessed to reduce the energy requirements of the water and wastewater treatment systems. The quality of drinking water cannot be compromised; however, the use of potable water flushing toilets can be avoided to conserve energy and resources. In approach 2A Standard sanitation technology (Scenario 1) was compared with the following alternative technologies high efficiency toilets flushed with potable water (Scenario 2), standard toilets flushed with rainwater (Scenario 3), high efficiency toilets flushed with rainwater (Scenario 4), and composting toilets (Scenario 5). These technologies were compared on two University Buildings, based on cost, energy and carbon emissions using Economic Input Output Life Cycle Assessment (EIO-LCA). Based on all the three indicators, scenarios 4 and 5 were the most preferable scenarios. Life cycle assessments (LCAs) are done largely either using the economic input-output approach or process based approach. While both methods are commonly used, it is not well known how much the LCA results might change when one method is used instead of the other. In approach 2B the technologies from 2A were compared with the conventional sanitation technology using EIO-LCA and process based LCA. The results were overall higher from EIO-LCA except for potable water treatment. EIO-LCA was found better for modeling. The difference in magnitude for all products and processes involved is reported. More detailed documentation from both models is required for an explanation of the difference in magnitudes. There was no difference in the suggested ranking of scenarios from both the models. In approach three, composting toilets were studied in more depth. The composting toilets technology demonstrated potential for the most sustainable sanitation technology among all the five technologies compared. In approach 3A, the composting results however, were preliminary. A review of the available composting toilet technologies and the composting process was conducted to better understand the technology. The review, categorized the different types of composting toilets. Factors reported as affecting the composting process and their optimum values were identified as; aeration, moisture content (50-60 %), temperature (40-65oC), carbon to nitrogen ratio (25-35), pH (5.5-8.0) and porosity (35-50%). Barriers in implementing this technology were also identified. In approach 3B, Composting is an old technology and more popular only in rural areas that are disconnected from the urban water and wastewater infrastructure. The impact of using these technologies in urban areas on a large scale has not been evaluated before. In approach 3B, use of composting toilets with land application and back yard application of compost were modeled in GaBi for a tenth of the city and compared to the conventional sanitation system for the city of Toledo. Results show that composting toilets are beneficial if a tenth of the city shifts from conventional to composting technology.

Download or read book The Energy Greenhouse Gas Emissions and Cost Implications of Municipal Water Supply Wastewater Treatment written by Rodriguez-Winter Thelma and published by . This book was released on 2014 with total page 110 pages. Available in PDF, EPUB and Kindle. Book excerpt: Most of our drinking water and wastewater infrastructure are at the end of their useful life facing significant deterioration, causing leaks and water losses. These losses are a waste of both energy and water, considering both water and wastewater treatment systems are very energy intensive. In order to deal with the urban water infrastructure issues, EPA has listed out the following goals: asset management, water and energy efficiency, infrastructure financing, price of water services and alternative technologies assessment. This dissertation addresses two of EPA's goals, water and energy efficiency and alternative technologies assessment. Three approaches were taken to address these goals. In the first approach, the life cycle energy demand for water and wastewater studies were reviewed from literature to understand the energy requirements of these systems and propose a benchmark energy demand. System boundaries, data collection and reporting, type of LCA used, were identified as the factors that influence the total energy use and energy use reporting. Energy use data of water and wastewater treatment systems have been compiled to obtain ranges of 2.8 x 10-06 - 4.8 x 10-03 kWh per L and 2.8 x 10-09 to 1.32 x 10-02 kWh per L respectively. From the details obtained from literature, energy use ranges for specific processes related to water and wastewater could not be obtained due to lack of appropriate data reporting. Development of an appropriate data reporting procedure for water and wastewater treatment life cycle assessments is required to be able to collect, use and analyze this data. In the second approach, alternative technologies were assessed to reduce the energy requirements of the water and wastewater treatment systems. The quality of drinking water cannot be compromised; however, the use of potable water flushing toilets can be avoided to conserve energy and resources. In approach 2A Standard sanitation technology (Scenario 1) was compared with the following alternative technologies high efficiency toilets flushed with potable water (Scenario 2), standard toilets flushed with rainwater (Scenario 3), high efficiency toilets flushed with rainwater (Scenario 4), and composting toilets (Scenario 5). These technologies were compared on two University Buildings, based on cost, energy and carbon emissions using Economic Input Output Life Cycle Assessment (EIO-LCA). Based on all the three indicators, scenarios 4 and 5 were the most preferable scenarios. Life cycle assessments (LCAs) are done largely either using the economic input-output approach or process based approach. While both methods are commonly used, it is not well known how much the LCA results might change when one method is used instead of the other. In approach 2B the technologies from 2A were compared with the conventional sanitation technology using EIO-LCA and process based LCA. The results were overall higher from EIO-LCA except for potable water treatment. EIO-LCA was found better for modeling. The difference in magnitude for all products and processes involved is reported. More detailed documentation from both models is required for an explanation of the difference in magnitudes. There was no difference in the suggested ranking of scenarios from both the models. In approach three, composting toilets were studied in more depth. The composting toilets technology demonstrated potential for the most sustainable sanitation technology among all the five technologies compared. In approach 3A, the composting results however, were preliminary. A review of the available composting toilet technologies and the composting process was conducted to better understand the technology. The review, categorized the different types of composting toilets. Factors reported as affecting the composting process and their optimum values were identified as; aeration, moisture content (50-60 %), temperature (40-65oC), carbon to nitrogen ratio (25-35), pH (5.5-8.0) and porosity (35-50%). Barriers in implementing this technology were also identified. In approach 3B, Composting is an old technology and more popular only in rural areas that are disconnected from the urban water and wastewater infrastructure. The impact of using these technologies in urban areas on a large scale has not been evaluated before. In approach 3B, use of composting toilets with land application and back yard application of compost were modeled in GaBi for a tenth of the city and compared to the conventional sanitation system for the city of Toledo. Results show that composting toilets are beneficial if a tenth of the city shifts from conventional to composting technology.

Download or read book Life Cycle Assessment of Wastewater Treatment written by Mu. Naushad and published by CRC Press. This book was released on 2018-03-15 with total page 386 pages. Available in PDF, EPUB and Kindle. Book excerpt: Life Cycle Assessment of Wastewater Treatment addresses in detail the required in-depth life cycle assessment of wastewater treatment. This is to meet the special demands placed upon wastewater treatment processes, due to both the limited quantity and often low quality of water supplies. Wastewater management clearly plays a central role in achieving future water security in a world where water stress is expected to increase. Life cycle assessment (LCA) can be used as a tool to evaluate the environmental impacts associated with wastewater treatment and potential improvement options. This unique volume will focus on the analysis of wastewater treatment plants (WWTPs), using a life cycle assessment (LCA) approach. Key Features: Focuses on the analysis of wastewater treatment plants using a life cycle assessment (LCA) approach Discusses unconventional water sources such as recycled wastewater, brackish groundwater and desalinated seawater Explains life cycle assessment in detail, which has become one of the reference methods used to assess the environmental performance of processes over their complete life cycle, from raw material extraction, infrastructure construction and operation to final dismantling Explores a technique (LCA) that is becoming increasingly popular amongst researchers in the water treatment field nowadays because of its holistic approach Based on the real life experiences, the subject of wastewater is presented in simple terms and made accessible to anyone willing to learn and experiment

Download or read book Modular Treatment Approach for Drinking Water and Wastewater written by Satinder Kaur Brar and published by Elsevier. This book was released on 2022-08-12 with total page 372 pages. Available in PDF, EPUB and Kindle. Book excerpt: Modular Treatment Approach for Drinking Water and Wastewater is a comprehensive resource that explores the latest studies and techniques in the field of treating water. It offers a new approach to tackling the demand for a high-quality, economic and green water treatment system and providing clean water globally. This book focuses on a modular strategy, which allows for a customized retrofit solution to the constantly changing parameters that are dependent on current demand and requirements. It summarizes the principles of modular design, as well as current developments and perspectives. Beginning with an introduction to sustainable and integrated water management, the book then delves into topics such as the use of modular systems for the removal of organic micropollutants; adsorbent-based reactors for modular wastewater treatment; filtration systems in modular drinking water treatment systems; and the use of solar energy in modular drinking water treatment. The book closes with a chapter on life cycle assessment for drinking water supply and treatment systems. Modular Treatment Approach for Drinking Water and Wastewater provides a detailed overview of wastewater and drinking water treatment and is a must-have for researchers, students and professors working in these areas. Presents the whole lifecycle of a modular treatment approach Includes global case studies, detailing the methods needed and the results possible for these treatment approaches Provides flow charts and diagrams, giving the reader a step-by-step guide to implementing these techniques in their work Explores futuristic approaches and changes in the wastewater treatment

Download or read book Biological Wastewater Treatment written by Mogens Henze and published by IWA Publishing (International Water Assoc). This book was released on 1881 with total page 170 pages. Available in PDF, EPUB and Kindle. Book excerpt: For information on the online course in Biological Wastewater Treatment from UNESCO-IHE, visit: http://www.iwapublishing.co.uk/books/biological-wastewater-treatment-online-course-principles-modeling-and-design Over the past twenty years, the knowledge and understanding of wastewater treatment have advanced extensively and moved away from empirically-based approaches to a first principles approach embracing chemistry, microbiology, physical and bioprocess engineering, and mathematics. Many of these advances have matured to the degree that they have been codified into mathematical models for simulation with computers. For a new generation of young scientists and engineers entering the wastewater treatment profession, the quantity, complexity and diversity of these new developments can be overwhelming, particularly in developing countries where access is not readily available to advanced level tertiary education courses in wastewater treatment. Biological Wastewater Treatment addresses this deficiency. It assembles and integrates the postgraduate course material of a dozen or so professors from research groups around the world that have made significant contributions to the advances in wastewater treatment. The book forms part of an internet-based curriculum in biological wastewater treatment which also includes: Summarized lecture handouts of the topics covered in book Filmed lectures by the author professors Tutorial exercises for students self-learning Upon completion of this curriculum the modern approach of modelling and simulation to wastewater treatment plant design and operation, be it activated sludge, biological nitrogen and phosphorus removal, secondary settling tanks or biofilm systems, can be embraced with deeper insight, advanced knowledge and greater confidence.

Download or read book Life Cycle Sustainability Assessment LCSA written by Subramanian Senthilkannan Muthu and published by Springer Nature. This book was released on 2021-09-21 with total page 206 pages. Available in PDF, EPUB and Kindle. Book excerpt: Environmental Life Cycle Assessment (ELCA) that was developed about three decades ago demands a broadening of its scope to include lifecycle costing and social aspects of life cycle assessment as well, drawing on the three-pillar or ‘triple bottom line’ model of sustainability, which is the result of the development of the Life Cycle Sustainability Assessment (LCSA). LCSA refers to the evaluation of all environmental, social and economic negative impacts and benefits in decision-making processes towards more sustainable products throughout their life cycle. Combination of environmental and social life cycle assessments along with life cycle costing leads to life cycle sustainability assessment (LCSA). This book highlights various aspects of life cycle sustainability assessment (LCSA).

Download or read book Source Separation and Decentralization for Wastewater Management written by Tove A. Larsen and published by IWA Publishing. This book was released on 2013-02-01 with total page 502 pages. Available in PDF, EPUB and Kindle. Book excerpt: Is sewer-based wastewater treatment really the optimal technical solution in urban water management? This paradigm is increasingly being questioned. Growing water scarcity and the insight that water will be an important limiting factor for the quality of urban life are main drivers for new approaches in wastewater management. Source Separation and Decentralization for Wastewater Management sets up a comprehensive view of the resources involved in urban water management. It explores the potential of source separation and decentralization to provide viable alternatives to sewer-based urban water management. During the 1990s, several research groups started working on source-separating technologies for wastewater treatment. Source separation was not new, but had only been propagated as a cheap and environmentally friendly technology for the poor. The novelty was the discussion whether source separation could be a sustainable alternative to existing end-of-pipe systems, even in urban areas and industrialized countries. Since then, sustainable resource management and many different source-separating technologies have been investigated. The theoretical framework and also possible technologies have now developed to a more mature state. At the same time, many interesting technologies to process combined or concentrated wastewaters have evolved, which are equally suited for the treatment of source-separated domestic wastewater. The book presents a comprehensive view of the state of the art of source separation and decentralization. It discusses the technical possibilities and practical experience with source separation in different countries around the world. The area is in rapid development, but many of the fundamental insights presented in this book will stay valid. Source Separation and Decentralization for Wastewater Management is intended for all professionals and researchers interested in wastewater management, whether or not they are familiar with source separation. Editors: Tove A. Larsen, Kai M. Udert and Judit Lienert, Eawag - Swiss Federal Institute of Aquatic Science and Technology, Switzerland. Contributors: Yuval Alfiya, Technion - Israel Institute of Technology, Faculty of Civil and Environmental Engineering; Prof. Dr. M. Bruce Beck, University of Georgia, Warnell School of Forestry and Natural Resources; Dr. Christian Binz, Eawag, Swiss Federal Institute of Aquatic Science and Technology, Innovation Research in Utility Sectors (Cirus); Prof. em. Dr. Markus Boller, Eawag, Swiss Federal Institute of Aquatic Science and Technology, Department of Urban Water Management (SWW); Prof. Dr. Eran Friedler, Technion – Israel Institute of Technology, Faculty of Civil and Environmental Engineering; Zenah Bradford-Hartke, The University of New South Wales, School of Chemical Engineering and UNESCO Centre for Membrane Science and Technology; Dr. Shelley Brown-Malker, Very Small Particle Company Ltd; Bert Bundervoet, Ghent University, Laboratory Microbial Ecology and Technology (LabMET); Prof. Dr. David Butler, University of Exeter, Centre for Water Systems; Dr. Christopher A. Buzie, Hamburg University of Technology, Institute of Wastewater Management and Water Protection; Dr. Dana Cordell, University of Technology, Sydney (UTS), Institute for Sustainable Futures (ISF); Dr. Vasileios Diamantis, Democritus University of Thrace, Department of Environmental Engineering; Prof. Dr. Jan Willem Erisman, Louis Bolk Institute; VU University Amsterdam, Department of Earth Sciences; Barbara Evans, University of Leeds, School of Civil Engineering; Prof. Dr. Malin Falkenmark, Stockholm International Water Institute; Dr. Ted Gardner, Central Queensland University, Institute for Resource Industries and Sustainability; Dr. Heiko Gebauer, Eawag, Swiss Federal Institute of Aquatic Science and Technology, Innovation Research in Utility Sectors (Cirus); Prof. em. Dr. Willi Gujer, Swiss Federal Institute of Technology Zürich (ETHZ), Department of Civil, Environmental and Geomatic Engineering (BAUG); Prof. Dr. Bruce Jefferson, Cranfield University, Cranfield Water Science Institute; Prof. Dr. Paul Jeffrey, Cranfield University, Cranfield Water Science Institute; Sarina Jenni, Eawag, Swiss Federal Institute of Aquatic Science and Technology, Process Engineering Department (Eng); Prof. Dr. Håkan Jönsson, SLU - Swedish University of Agricultural Sciences, Department of Energy and Technology; Prof. Dr. Ïsik Kabdasli, Ïstanbul Technical University, Civil Engineering Faculty; Prof. Dr. Jörg Keller, The University of Queensland, Advanced Water Management Centre (AWMC); Prof. Dr. Klaus Kömmerer, Leuphana Universität Lüneburg, Institute of Sustainable and Environmental Chemistry; Dr. Katarzyna Kujawa-Roeleveld, Wageningen University, Agrotechnology and Food Sciences Group; Dr. Tove A. Larsen, Eawag, Swiss Federal Institute of Aquatic Science and Technology, Department of Urban Water Management (SWW); Michele Laureni, Eawag, Swiss Federal Institute of Aquatic Science and Technology, Process Engineering Department (Eng); Prof. Dr. Gregory Leslie, The University of New South Wales, School of Chemical Engineering and UNESCO Centre for Membrane Science and Technology; Dr. Harold Leverenz, University of California at Davis, Department of Civil and Environmental Engineering; Dr. Judit Lienert, Eawag, Swiss Federal Institute of Aquatic Science and Technology, Department of Environmental Social Sciences (ESS); Prof. Dr. Jürg Londong, Bauhaus-Universität Weimar, Department of Urban Water Management and Sanitation; Dr. Christoph Lüthi, Eawag, Swiss Federal Institute of Aquatic Science and Technology, Water and Sanitation in Developing Countries (Sandec); Prof. Dr. Max Maurer, Eawag, Swiss Federal Institute of Aquatic Science and Technology, Department of Urban Water Management (SWW); Swiss Federal Institute of Technology Zürich (ETHZ), Department of Civil, Environmental and Geomatic Engineering; Prof. em. Dr. Gustaf Olsson, Lund University, Department of Measurement Technology and Industrial Electrical Engineering (MIE); Prof. Dr. Ralf Otterpohl, Hamburg University of Technology, Institute of Wastewater Management and Water Protection; Dr. Bert Palsma, STOWA, Dutch Foundation for Applied Water Research; Dr. Arne R. Panesar, Deutsche Gesellschaft für Internationale Zusammenarbeit (GIZ) GmbH; Prof. Dr. Bruce E. Rittmann, Arizona State University, Swette Center for Environmental Biotechnology; Prof. Dr. Hansruedi Siegrist, Eawag, Swiss Federal Institute of Aquatic Science and Technology, Process Engineering Department (Eng); Dr. Ashok Sharma, Commonwealth Scientific and Industrial Research Organisation, Australia, Land and Water Division; Prof. Dr. Thor Axel Stenström, Stockholm Environment Institute, Bioresources Group; Norwegian University of Life Sciences, Department of Mathematical Science and Technology; Dr. Eckhard Störmer, Eawag, Swiss Federal Institute of Aquatic Science and Technology, Innovation Research in Utility Sectors (Cirus); Bjartur Swart, STOWA, Dutch Foundation for Applied Water Research; MWH North Europe; Prof. em. Dr. George Tchobanoglous, University of California at Davis, Department of Civil and Environmental Engineering; Elizabeth Tilley, Eawag, Swiss Federal Institute of Aquatic Science and Technology, Department of Water and Sanitation in Developing Countries (Sandec); Swiss Federal Institute of Technology Zürich (ETHZ), Centre for Development and Cooperation (NADEL); Prof. Dr. Bernhard Truffer, Eawag, Swiss Federal Institute of Aquatic Science and Technology; Innovation Research in Utility Sectors (Cirus); Prof. Dr. Olcay Tünay, Ïstanbul Technical University, Civil Engineering Faculty; Dr. Kai M. Udert, Eawag, Swiss Federal Institute of Aquatic Science and Technology, Process Engineering Department (Eng); Prof. em. Dr. Willy Verstraete, Ghent University, Laboratory Microbial Ecology and Technology (LabMET); Prof. Dr. Björn Vinnerås, SLU - Swedish University of Agricultural Sciences, Department of Energy and Technology; Prof. Dr. Urs von Gunten, Eawag, Swiss Federal Institute of Aquatic Science and Technology, Department of Water Resources and Drinking Water (W+T); Ecole Polytechnique Fédérale de Lausanne (EPFL),School of Architecture, Civil and Environmental Engineering (ENAC); Prof. em. Dr. Peter A. Wilderer, Technische Universität München, Institute for Advanced Study; Prof. Dr. Jun Xia, Chinese Academy of Sciences (CAS), Center for Water Resources Research and Key Laboratory of Water Cycle and Related Surface Processes; Prof. Dr. Grietje Zeeman, Wageningen University, Agrotechnology and Food Sciences Group

Download or read book Life Cycle Assessment LCA written by Allan Astrup Jensen and published by . This book was released on 1998 with total page 132 pages. Available in PDF, EPUB and Kindle. Book excerpt: Life Cycle Assessment

Download or read book Qualitative and Quantitative Procedure for Uncertainty Analysis in Life Cycle Assessment of Wastewater Solids Treatment Processes written by Isam Al-Yaseri and published by . This book was released on 2014 with total page 221 pages. Available in PDF, EPUB and Kindle. Book excerpt: In order to perform the environmental analysis and find the best management in the wastewater treatment processes using life cycle assessment (LCA) method, uncertainty in LCA has to be evaluated. A qualitative and quantitative procedure was constructed to deal with uncertainty for the wastewater treatment LCA studies during the inventory and analysis stages. The qualitative steps in the procedure include setting rules for the inclusion of inputs and outputs in the life cycle inventory (LCI), setting rules for the proper collection of data, identifying and conducting data collection analysis for the significant contributors in the model, evaluating data quality indicators, selecting the proper life cycle impact assessment (LCIA) method, evaluating the uncertainty in the model through different cultural perspectives, and comparing with other LCIA methods. The quantitative steps in the procedure include assigning the best guess value and the proper distribution for each input or output in the model, calculating the uncertainty for those inputs or outputs based on data characteristics and the data quality indicators, and finally using probabilistic analysis (Monte Carlo simulation) to estimate uncertainty in the outcomes. Environmental burdens from the solids handling unit at Bissell Point Wastewater Treatment Plant (BPWWTP) in Saint Louis, Missouri was analyzed. Plant specific data plus literature data were used to build an input-output model. Environmental performance of an existing treatment scenario (dewatering-multiple hearth incineration-ash to landfill) was analyzed. To improve the environmental performance, two alternative scenarios (fluid bed incineration and anaerobic digestion) were proposed, constructed, and evaluated. System boundaries were set to include the construction, operation and dismantling phases. The impact assessment method chosen was Eco-indicator 99 and the impact categories were: carcinogenicity, respiratory organics and inorganics, climate change, radiation, ozone depletion, ecotoxicity, acidification-eutrophication, and minerals and fossil fuels depletion. Analysis of the existing scenario shows that most of the impacts came from the operation phase on the categories related to fossil fuels depletion, respiratory inorganics, and carcinogens due to energy consumed and emissions from incineration. The proposed alternatives showed better performance than the existing treatment. Fluid bed incineration had better performance than anaerobic digestion. Uncertainty analysis showed there is 57.6% possibility to have less impact on the environment when using fluid bed incineration than the anaerobic digestion. Based on single scores ranking in the Eco-indicator 99 method, the environmental impact order is: multiple hearth incineration > anaerobic digestion > fluid bed incineration. This order was the same for the three model perspectives in the Eco-indicator 99 method and when using other LCIA methods (Eco-point 97 and CML 2000). The study showed that the incorporation of qualitative/quantitative uncertainty analysis into LCA gave more information than the deterministic LCA and can strengthen the LCA study. The procedure tested in this study showed that Monte Carlo simulation can be used in quantifying uncertainty in the wastewater treatment studies. The procedure can be used to analyze the performance of other treatment options. Although the analysis in different perspectives and different LCIA methods did not impact the order of the scenarios, it showed a possibility of variation in the final outcomes of some categories. The study showed the importance of providing decision makers with the best and worst possible outcomes in any LCA study and informing them about the perspectives and assumptions used in the assessment. Monte Carlo simulation is able to perform uncertainty analysis in the comparative LCA only between two products or scenarios based on the (A-B) approach due to the overlapping between the probability distributions of the outcomes. It is recommended to modify it to include more than two scenarios.

Download or read book Integrated Solid Waste Management A Lifecycle Inventory written by P.R. White and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 374 pages. Available in PDF, EPUB and Kindle. Book excerpt: Life is often considered to be a journey. The lifecycle of waste can similarly be considered to be a journey from the cradle (when an item becomes valueless and, usually, is placed in the dustbin) to the grave (when value is restored by creating usable material or energy; or the waste is transformed into emissions to water or air, or into inert material placed in a landfill). This preface provides a route map for the journey the reader of this book will undertake. Who? Who are the intended readers of this book? Waste managers (whether in public service or private companies) will find a holistic approach for improving the environmental quality and the economic cost of managing waste. The book contains general principles based on cutting edge experience being developed across Europe. Detailed data and a computer model will enable operations managers to develop data-based improvements to their systems. Producers oj waste will be better able to understand how their actions can influence the operation of environmentally improved waste management systems. Designers oj products and packages will be better able to understand how their design criteria can improve the compatibility of their product or package with developing, environmentally improved waste management systems. Waste data specialists (whether in laboratories, consultancies or environ mental managers of waste facilities) will see how the scope, quantity and quality of their data can be improved to help their colleagues design more effective waste management systems.

Download or read book Decentralized Sanitation and Water Treatment written by Rajeshwar D Tyagi and published by CRC Press. This book was released on 2024-04-26 with total page 254 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book discusses decentralized sanitation for wastewater treatment and management in cold environments. It addresses the knowledge gap that exists between the understanding of centralized and decentralized wastewater treatment approaches. Decentralized Sanitation and Water Treatment: Treatment in Cold Environments and Techno-Economic Aspects covers the sustainability principles, various technologies involved, decentralized treatment in cold countries, and the economic and social feasibility of decentralized sanitation. It provides solutions for the conservation of water sources and target-oriented sanitation approaches for wastewater treatment and recycling. Key Features Reviews the current status, challenges, and future perspectives of decentralized water treatments Discusses decentralized sanitation, water, and wastewater treatment in cold environments and Northern countries Focuses on interdisciplinary approaches of sustainability and circular economy Covers life cycle and environment assessment of decentralized sanitation systems Reviews the environmental, techno-economic, and social aspects of decentralized sanitation systems The book is meant for professionals and researchers working on wastewater treatment, environmental engineering, and ecology.

Download or read book Handbook on Life Cycle Sustainability Assessment written by Guido Sonnemann and published by Edward Elgar Publishing. This book was released on 2024-04-12 with total page 461 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Handbook presents the state-of-the-art of Life Cycle Sustainability Assessment (LCSA) practice and provides guidance for its implementation and outlook for future work. Spotlighting sustainability analysts, managers and overall decision-makers from private and public sectors as well as experts in academia, it covers the historical background and current global context for life cycle sustainability assessment, methods and data management advancements.

Download or read book Sustainable Membrane Technology for Water and Wastewater Treatment written by Alberto Figoli and published by Springer. This book was released on 2017-09-19 with total page 388 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book analyses the sustainability of membrane operations applied on an industrial scale, as well as that of those under investigation on lab/pilot scales, covering also the preparation of both polymeric and inorganic membranes. It presents reverse osmosis in desalination, membrane bioreactors for municipal wastewater treatment and pressure-driven industrial wastewater treatment in agrofood and textile fields as examples of industrial membrane operations. Regarding the membrane processes still on a lab/pilot scale, the analysis includes membrane operations for the recovery of valuable products from wastewater streams, for the removal of toxic compounds from water/wastewater, and for zero liquid discharge approaches in desalination. The book offers a useful guide for scientists and engineers working in various fields, including membrane technology, separation, desalination, and wastewater treatment. Alberto Figoli and Alessandra Criscuoli are both Senior Researchers at the Institute on Membrane Technology (ITM-CNR), Italy.

Download or read book Current Developments in Biotechnology and Bioengineering written by Giorgio Mannina and published by Elsevier. This book was released on 2022-09-21 with total page 456 pages. Available in PDF, EPUB and Kindle. Book excerpt: Smart Solutions for Wastewater: Road-mapping the Transition to Circular Economy, the latest release in the Current Developments in Biotechnology and Bioengineering presents up-to-date information on research and technological developments of resource recovery in wastewater treatment in terms of carbon, nutrients and energy. The book fulfils the gaps and current challenges that hinder the application of resource recovery facilities in wastewater treatment plants, discusses knowledge gaps, provides future research perspectives, and discusses strategies to solve problems from a circular economy perspective. It is an excellent, interdisciplinary and updated overview of technologies in terms of potential yields, pollutants removal, nutrients recovery and energy production. Covers different aspects of resource recovery technologies and research gaps in wastewater treatment Focuses on different MBR configurations and systems/hybrid systems in treating a large variety of wastewaters Provides state-of-the-art technology developments, including technology, advantages and challenges as well as strategies to overcome limitations Includes technologies for managing sewage sludge in order to foster solutions for recovering in a circular economy context

Download or read book Water 4 0 written by David Sedlak and published by Yale University Press. This book was released on 2014-01-28 with total page 405 pages. Available in PDF, EPUB and Kindle. Book excerpt: The history behind our growing water crisis: “A gem . . . An erudite romp through two millennia of water and sanitation practice and technology.” —Nature Turn on the faucet, and water pours out. Pull out the drain plug, and the dirty water disappears. Most of us give little thought to the hidden systems that bring us water and take it away when we’re done with it. But these underappreciated marvels of engineering face an array of challenges that cannot be solved without a fundamental change to our relationship with water, David Sedlak explains in this enlightening book. To make informed decisions about the future, we need to understand the three revolutions in urban water systems that have occurred over the past 2,500 years, and the technologies that will remake the system. The author starts by describing Water 1.0, the early Roman aqueducts, fountains, and sewers that made dense urban living feasible. He then details the development of clean drinking water and sewage treatment systems—the second and third revolutions in urban water. He offers an insider’s look at current systems that rely on reservoirs, underground pipe networks, treatment plants, and storm sewers to provide water that is safe to drink, before addressing how these water systems will have to be reinvented. For everyone who cares about reliable, clean, abundant water, this book is essential reading.

Download or read book Life Cycle Assessment written by Michael Z. Hauschild and published by Springer. This book was released on 2017-09-01 with total page 1215 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is a uniquely pedagogical while still comprehensive state-of-the-art description of LCA-methodology and its broad range of applications. The five parts of the book conveniently provide: I) the history and context of Life Cycle Assessment (LCA) with its central role as quantitative and scientifically-based tool supporting society’s transitioning towards a sustainable economy; II) all there is to know about LCA methodology illustrated by a red-thread example which evolves as the reader advances; III) a wealth of information on a broad range of LCA applications with dedicated chapters on policy development, prospective LCA, life cycle management, waste, energy, construction and building, nanotechnology, agrifood, transport, and LCA-related concepts such as footprinting, ecolabelling,design for environment, and cradle to cradle. IV) A cookbook giving the reader recipes for all the concrete actions needed to perform an LCA. V) An appendix with an LCA report template, a full example LCA report serving as inspiration for students who write their first LCA report, and a more detailed overview of existing LCIA methods and their similarities and differences.

Download or read book Sustainable Resource Management written by Wenshan Guo and published by John Wiley & Sons. This book was released on 2021-04-08 with total page 832 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sustainable Resource Management Learn how current technologies can be used to recover and reuse waste products to reduce environmental damage and pollution In this two-volume set, Sustainable Resource Management: Technologies for Recovery and Reuse of Energy and Waste Materials delivers a compelling argument for the importance of the widespread adoption of a holistic approach to enhanced water, energy, and waste management practices. Increased population and economic growth, urbanization, and industrialization have put sustained pressure on the world’s environment, and this book demonstrates how to use organics, nutrients, and thermal heat to better manage wastewater and solid waste to deal with that reality. The book discusses basic scientific principles and recent technological advances in current strategies for resource recovery from waste products. It also presents solutions to pressing problems associated with energy production during waste management and treatment, as well as the health impacts created by improper waste disposal and pollution. Finally, the book discusses the potential and feasibility of turning waste products into resources. Readers will also enjoy: A thorough introduction and overview to resource recovery and reuse for sustainable futures An exploration of hydrothermal liquefaction of food waste, including the technology’s use as a potential resource recovery strategy A treatment of resource recovery and recycling from livestock manure, including the current state of the technology and future prospects and challenges A discussion of the removal and recovery of nutrients using low-cost adsorbents from single-component and multi-component adsorption systems Perfect for water and environmental chemists, engineers, biotechnologists, and food chemists, Sustainable Resource Management also belongs on the bookshelves of environmental officers and consultants, chemists in private industry, and graduate students taking programs in environmental engineering, ecology, or other sustainability related fields.