Download or read book Etude de mat riaux composites matrice base Al renforc s par des particules Al Cu Fe written by Tarik El Kabir and published by . This book was released on 2007 with total page 112 pages. Available in PDF, EPUB and Kindle. Book excerpt: Les matériaux quasicristallins (QC) présentent des propriétés mécaniques intéressantes, telles une dureté et un module d’Young élevés, ce qui en fait de bons candidats en tant que renforts pour les matériaux composites à matrices métalliques. Ce travail a pour but l’élaboration et l’étude des microstructures et propriétés mécaniques de matériaux composites à base Al renforcés par des particules QC. Des composites à matrice Al3Mg2, Al, Al-Cu-Mg et Al-Mg-Si renforcés par 50% vol. de particules QC Al-Cu-Fe ont été élaborés par infiltration sous pression de gaz. Les composites obtenus sont complexes et présentent de nombreuses phases résultant de la diffusion de l’aluminium et du cuivre. Ces composites sont caractérisés par des contraintes d’écoulement élevées et une fissuration précoce, quelle que soit la température de déformation. Deux composites à matrice aluminium renforcés par des particules QC ont été élaborés par compression isostatique à chaud (HIP). En fonction de la température d’élaboration, nous avons obtenu des matériaux biphasés, l’un renforcé par des particules tétragonales w-Al-Cu-Fe et l’autre par des particules i-Al-Cu-Fe. Ces matériaux présentent des propriétés mécaniques améliorées par rapport à la matrice seule. La forte dépendance de s0.2% en température observée dans le composite Al/w suggère que la déformation plastique est contrôlée par des mécanismes thermiquement activés. En revanche, pour le composite Al/i, la contribution des contraintes internes au durcissement du composite est à prendre en compte en plus des mécanismes thermiquement activés.
Download or read book Mechanics of Composite Materials and Structures written by Carlos A. Mota Soares and published by Springer Science & Business Media. This book was released on 2013-06-29 with total page 524 pages. Available in PDF, EPUB and Kindle. Book excerpt: A compact presentation of the foundations, current state of the art, recent developments and research directions of all essential techniques related to the mechanics of composite materials and structures. Special emphasis is placed on classic and recently developed theories of composite laminated beams, plates and shells, micromechanics, impact and damage analysis, mechanics of textile structural composites, high strain rate testing and non-destructive testing of composite materials and structures. Topics of growing importance are addressed, such as: numerical methods and optimisation, identification and damage monitoring. The latest results are presented on the art of modelling smart composites, optimal design with advanced materials, and industrial applications. Each section of the book is written by internationally recognised experts who have dedicated most of their research work to a particular field. Readership: Postgraduate students, researchers and engineers in the field of composites. Undergraduate students will benefit from the treatment of the foundations of the mechanics of composite materials and structures.
Download or read book Adhesion Between Polymers and Concrete Adh sion Entre Polym res Et B ton written by H. R. Sasse and published by Springer. This book was released on 1986 with total page 792 pages. Available in PDF, EPUB and Kindle. Book excerpt: Preface Adhesion is a phenomenon architects and civil engineers are not very familiar with. In other disciplines knowledge about surface properties and the background of bonding energies is also far from satisfactory; nevertheless there are many important· applications in concrete engineering, where adhesion is necessary for success and durability. These include: - coating and painting - repair of concrete surfaces - bonding of fresh to old concrete - crack injection - glueing of precast elements - glueing of steel to concrete, etc. In 1981 RILEM established the technical committee 52-RAC 'Resin Adherence to Concrete'. The main aims of the committee's work were - to collect research results and practical experiences - to initiate and coordinate research programs - to develop, on a scientific base, test methods for field and for laboratory purposes. One of the results of the committee's work is a state-of-the-art report, which will be presented orally as a General Report at the International Symposium ISAP '86, and will be printed either in the RILEM journal Materials and Structures or separately. Several test recommendations have been elaborated and will be prepared as drafts for the participants ofISAP '86. These are: - direct tensile test - pull-off test - direct shear test - slant shear test - four-point bending test - dynamic loading test - thermal compatibility test (two versions) - injectibility test.
Download or read book Performance of Cement Based Materials in Aggressive Aqueous Environments written by Mark Alexander and published by Springer Science & Business Media. This book was released on 2012-12-18 with total page 471 pages. Available in PDF, EPUB and Kindle. Book excerpt: Concrete and cement-based materials must operate in increasingly aggressive aqueous environments, which may be either natural or industrial. These materials may suffer degradation in which ion addition and/or ion exchange reactions occur, leading to a breakdown of the matrix microstructure and consequent weakening. Sometimes this degradation can be extremely rapid and serious such as in acidic environments, while in other cases degradation occurs over long periods. Consequences of material failure are usually severe – adversely affecting the health and well-being of human communities and disturbing ecological balances. There are also large direct costs of maintaining and replacing deteriorated infrastructure and indirect costs from loss of production during maintenance work, which place a great burden on society. The focus of this book is on addressing issues concerning performance of cement-based materials in aggressive aqueous environments , by way of this State-of-the-Art Report. The book represents the work of many well-known and respected authors who contributed chapters or parts of chapters. Four main themes were addressed: I. Nature and kinetics of degradation and deterioration mechanisms of cement-based materials in aggressive aqueous environments, II. Modelling of deterioration in such environments, III. Test methods to assess performance of cement-based materials in such environments, and which can be used to characterise and rate relative performance and inform long term predictions, IV. Engineering implications and consequences of deterioration in aggressive aqueous environments, and engineering approaches to the problem.
Download or read book Le Golfe Du Saint Laurent petit Oc an Ou Grand Estuaire written by Canada. Department of Fisheries and Oceans and published by Peches Et Oceans Direction Generale Des Communications = Fisheries and Oceans Communications Dir. This book was released on 1991 with total page 376 pages. Available in PDF, EPUB and Kindle. Book excerpt: Proceedings of a workshop, the scientific reviews and the contributed papers presented at the symposium. The document presents a brief historical summary of marine research in the Gulf; reports the discussions, conclusions and recommendations of the different working groups on oceanography (physics, biology, chemistry and sedimentology) and on the fishery (fish and invertebrates); then presents the discussions of each multidisciplinary working group, centered around how the St. Lawrence system may be used as a natural laboratory which will contribute to the solution of major long-term problems of conservation of natural resources and of the quality of the environment.
Download or read book Renewable Energy for Smart and Sustainable Cities written by Mustapha Hatti and published by Springer. This book was released on 2018-11-23 with total page 571 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book features cutting-edge research presented at the second international conference on Artificial Intelligence in Renewable Energetic Systems, IC-AIRES2018, held on 24–26 November 2018, at the High School of Commerce, ESC-Koléa in Tipaza, Algeria. Today, the fundamental challenge of integrating renewable energies into the design of smart cities is more relevant than ever. While based on the advent of big data and the use of information and communication technologies, smart cities must now respond to cross-cutting issues involving urban development, energy and environmental constraints; further, these cities must also explore how they can integrate more sustainable energies. Sustainable energies are a major determinant of smart cities’ longevity. From an environmental and technological standpoint, these energies offer an optimal power supply to the electric network while creating significantly less pollution. This requires flexibility, i.e., the availability of supply and demand. The end goal of any smart city is to improve the quality of life for all citizens (both in the city and in the countryside) in a way that is sustainable and respectful of the environment. This book encourages the reader to engage in the preservation of our environment, every moment, every day, so as to help build a clean and healthy future, and to think of the future generations who will one day inherit our planet. Further, it equips those whose work involves energy systems and those engaged in modelling artificial intelligence to combine their expertise for the benefit of the scientific community and humanity as a whole.
Download or read book The Physics and Chemistry of SiO2 and the Si SiO2 Interface 2 written by B.E. Deal and published by Springer Science & Business Media. This book was released on 2013-11-09 with total page 505 pages. Available in PDF, EPUB and Kindle. Book excerpt: The first international symposium on the subject "The Physics and Chemistry of Si02 and the Si-Si02 Interface," organized in association with the Electrochemical Society, Inc. , was held in Atlanta, Georgia on May 15- 20, 1988. This symposium contained sixty papers and was so successful that the sponsoring divisions decided to schedule it on a regular basis every four years. Thus, the second symposium on "The Physics and Chemistry of Si02 and the Si02 Interface was held May 18-21, 1992 in St. Louis, Missouri, again sponsored by the Electronics and Dielectrics Science and Technology Divisions of The Electrochemical Society. This volume contains manuscripts of most of the fifty nine papers presented at the 1992 symposium, and is divided into eight chapters - approximating the organization of the symposium. Each chapter is preceded with an introduction by the session organizers. It is appropriate to provide a general assessment of the current status and understanding of the physics and chemistry of Si02 and the Si02 interface before proceeding with a brief overview of the individual chapters. Semiconductor devices have continued to scale down in both horizontal and vertical dimensions. This has resulted in thinner gate and field oxides as well as much closer spacing of individual device features. As a result, surface condition, native oxide composition, and cleaning and impurity effects now provide a much more significant contribution to the properties of oxides and their interfaces.
Download or read book Tribologie Pour Les Syst mes A rospatiaux written by North Atlantic Treaty Organization. Advisory Group for Aerospace Research and Development. Structures and Materials Panel. Meeting and published by . This book was released on 1996 with total page 202 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Environmental Effects on Composite Materials Volume I written by George S. Springer and published by CRC Press. This book was released on 1981 with total page 222 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Solidification Processing written by Merton C. Flemings and published by McGraw-Hill Companies. This book was released on 1974 with total page 386 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Graphite and Precursors written by Pierre Delhaes and published by CRC Press. This book was released on 2000-12-21 with total page 316 pages. Available in PDF, EPUB and Kindle. Book excerpt: Humans first used carbon as chars from firewood in ritual paintings and primitive metallurgical processes. Natural forms of carbon have been known since antiquity, yet the knowledge of the carbon element in chemistry and its technical applications on a larger scale are a relatively recent development. The industrial revolution in Europe two centuries ago led the way to the numerous applications of these graphitic forms that are still used today. Graphite and Precursors features short tutorial articles on different topics related to the science and technology of carbons intended for engineers, students of Materials Science and scientists who are seeking a fundamental understanding without "reinventing the wheel." This first volume of the World of Carbon book series focuses on graphite and its precursors, including its origin and various implications. The basic properties of hexagonal graphite are developed, and several theoretical and experimental approaches explain why this crystalline solid is fascinating in solid state physics. Also featured are the numerous applications connected to thermal, mechanical and chemical graphites, as well as their various industrial uses in polycrystalline form. Finally, carbon precursors are introduced.
Download or read book Composite Materials written by Isaac M. Daniel and published by ASTM International. This book was released on 1982 with total page 608 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Treatise on Geophysics Volume 7 written by David Bercovici and published by Elsevier. This book was released on 2010-05-17 with total page 521 pages. Available in PDF, EPUB and Kindle. Book excerpt: Treatise on Geophysics: Mantle Dynamics, Volume 7 aims to provide both a classical and state-of-the-art introduction to the methods and science of mantle dynamics, as well as survey leading order problems (both solved and unsolved) and current understanding of how the mantle works. It is organized around two themes: (1) how is mantle convection studied; and (2) what do we understand about mantle dynamics to date. The first four chapters are thus concerned with pedagogical reviews of the physics of mantle convection; laboratory studies of the fluid dynamics of convection relevant to the mantle; theoretical analysis of mantle dynamics; and numerical analysis and methods of mantle convection. The subsequent chapters concentrate on leading issues of mantle convection itself, which include the energy budget of the mantle; the upper mantle and lithosphere in and near the spreading center (mid-ocean ridge) environment; the dynamics of subducting slabs; hot spots, melting anomalies, and mantle plumes; and finally, geochemical mantle dynamics and mixing. - Self-contained volume starts with an overview of the subject then explores each topic in detail - Extensive reference lists and cross references with other volumes to facilitate further research - Full-color figures and tables support the text and aid in understanding - Content suited for both the expert and non-expert
Download or read book Science of Hard Materials written by R. Viswanadham and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 990 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume contains the proceedings of the first International Conference on the Science of Hard Materials held in Moran, Wyoming, Aug. 23-28, 1981. The objective of the conference was to review and advance the state of knowledge of the basic physical and chemical properties of hard materials and show how these properties influence performance in a variety of applications. To this end, the 49 con tributed papers and the four keynote papers by Prof. Fischmeister and Drs. Hintermann, Exner and Almond, present an excellent overview of the state of the art in the "science" of hard materials. The contents of these proceedings also reflect the fact that hard metal technology is now well matured and several aspects of the behavior of these materials are well understood and firmly established. Structure-property relationships in this class of materials are currently well known. Pitfalls in some of the traditional test methods have been recognized and new test methods are being developed which discriminate between intrinsic material properties and flaw content and distribution. Application of fracture mechanics, al though a late corner to the hard materials area (as compared to other structural materials), is rapidly gaining acceptance and new fracture toughness test methods are being developed. Application of modern analysis and analytical techniques to these materials has begun and entirely new and unexpected information has been obtained. For a variety of reasons, "hard metals" have dominated the research and development scene of "hard materials".
Download or read book Inclusions and Their Influence on Material Behavior written by R. Rungta and published by . This book was released on 1988 with total page 216 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Corrosion Guide written by E. Rabald and published by Elsevier. This book was released on 2012-12-02 with total page 937 pages. Available in PDF, EPUB and Kindle. Book excerpt: Corrosion Guide presents a list of corrosive agents and the trade names of materials, including metallic and non-metallic materials as well as alloys. The book provides guidance in using the tabulated information. This reference also lists relevant publications that deal with the properties of various materials. This new edition provides more data that are not included in the previous edition. The former edition fails to present enough information as the provided properties of the corrosive agents varies and other data are not available. The release aims to minimize missing information about the subject matter. This compilation of tabulated data provides description of each group of corrosive agents. Elements and compounds under each group are listed, along with their properties such as room temperature, corrosion rate, and composition. The list of trade names of materials also describes the composition of each material. The information contained in this book is intended to help practicing engineers deal with corrosion.
Download or read book The Nimonic Alloys and Other Nickel base High temperature Alloys written by J. Heslop and published by . This book was released on 1974 with total page 518 pages. Available in PDF, EPUB and Kindle. Book excerpt:
