Download or read book Environmental Compliance Guide for Ontario Metal Finishers written by and published by . This book was released on 2004 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Environmental Compliance and Pollution Prevention Guide for the Metal Finishing Industry written by New York (State). Department of Environmental Conservation. Pollution Prevention Unit and published by . This book was released on 2001 with total page 74 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Metal Finishing Guidance Manual written by and published by . This book was released on 1996 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book An Environmental Guide for Texas Metal Finishers written by and published by . This book was released on 2000 with total page 52 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Environmental Aspects of the Metal Finishing Industry written by and published by . This book was released on 1989 with total page 106 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Guides to Pollution Prevention written by and published by . This book was released on 1992 with total page 78 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Enforcing Pollution Control Regulation written by Carolyn Abbot and published by Bloomsbury Publishing. This book was released on 2009-05-18 with total page 292 pages. Available in PDF, EPUB and Kindle. Book excerpt: Monitoring and enforcement issues must be analysed when determining the effectiveness of pollution control regulation, and clearly influence choices about how to regulate. This book demonstrates how an economic analysis of law enforcement can generate important insights into how best to enforce pollution control regulation. It seeks to provide a clear and accessible way into the law and economics literature on enforcement. More specifically, it uses Gary Becker's deterrence model which, by differentiating between two enforcement variables (namely the probability of apprehension and conviction and the severity of sanction), facilitates a comparison of the effectiveness of different enforcement tools in inducing desirable behaviour. As such, it provides a valuable analytical tool in considering how best to pursue cost-effective enforcement. Major themes to be addressed include Becker's deterrence model and expansions thereof, reasons for compliance, environmental enforcement strategies and the importance of a deterrence threat and formal pollution control law enforcement mechanisms such as prosecution and criminal sanctions, administrative mechanisms and civil liability. The book argues that in pursuing cost-effective enforcement much can be learned from examining enforcement practices in different jurisdictions, and to this end the author examines pollution control laws, enforcement strategies and sanctions in Australia, Canada and England and Wales. The book makes an important contribution to existing literature on environmental law enforcement, but its value extends beyond this. The theoretical framework adopted and the range of issues discussed make it of interest to regulatory and public law scholars more generally.

Download or read book Environmental Management Systems written by Christine A. Branson and published by . This book was released on 1998 with total page 96 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Hazardous Waste Reducation in the Metal Finishing Industry written by PRC Environmental Management, Inc and published by William Andrew. This book was released on 1989-12-31 with total page 232 pages. Available in PDF, EPUB and Kindle. Book excerpt: "From the Foreword: " This book presents the results of a waste audit study for the metal finishing industry. The study, carried out for the State of California but applicable for metal finishers elsewhere, identifies opportunities for waste reduction available to the metal finishing industry and develops procedures that can be used by metal finishers to assess their own waste reduction opportunities. The study emphasizes technologies available to small- and medium-sized metal finishing plants. Typically, these shops operate a variety of physical, chemical, and electrochemical processes. Chemical processes include degreasing, cleaning, pickling, etching, coating, and electroless plating. Electrochemical processes include plating and anodizing. The tasks included in the study were: (1) selecting metal finishing plants to include in the study, (2) performing a waste audit at each selected plant, (3) developing recommendations for implementing waste reduction technologies at each audited plant, (4) discussing with facility representatives the feasibility of implementing the waste reduction recommendations, and (5) developing this waste audit study report and methodology. The study identifies three categories of waste reduction technologies that are available to metal finishers: (1) source reduction, (2) recycling and resource recovery, and (3) alternative treatment. The costs associated with implementing these technologies range from a few hundred dollars for making simple improvements in housekeepiing and minor process modifications to tens of thousands of dollars for installing recovery or treatment units. The benefits realized from implementing such improvements include reductions inmaterial purchase and waste disposal costs, as well as reduction in the liability

Download or read book An Assessment of the Financial Impact of Federal Guidelines on the Canadian Metal Finishing Industry written by L. Buffa and published by [Hull, Quebec] : Environment Canada, Environmental Protection Service. This book was released on 1978 with total page 64 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Environmental Aspects of the Metal Finishing Industry written by Programa de las Naciones Unidas para el Medio Ambiente Industry and Environment Office and published by . This book was released on 1989 with total page 91 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Metal Finishing Pollution Prevention Manual written by and published by . This book was released on 2001 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Plating and Surface Finishing written by and published by . This book was released on 2004 with total page 368 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Canadian Environmental Protection Act 1999 written by Canada. Environment Canada and published by . This book was released on 2005 with total page 96 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Guidance Manual for Compliance with the Filtration and Disinfection Requirements for Public Water Systems Using Surface Water Sources written by David J. Hiltebrand and published by . This book was released on 1991 with total page 672 pages. Available in PDF, EPUB and Kindle. Book excerpt: This manual suggests design operating and performance criteria for specific surface water quality conditions to provide the optimum protection from microbiological contaminants.

Download or read book Metal Finishing written by and published by . This book was released on 1940 with total page 1474 pages. Available in PDF, EPUB and Kindle. Book excerpt: Issues for Oct. 1939-Dec. 1944 include v. 1-5 of Organic finishing (later issued separately)

Download or read book Tools and Methods for Pollution Prevention written by Subhas K. Sikdar and published by Springer Science & Business Media. This book was released on 1999-08-31 with total page 404 pages. Available in PDF, EPUB and Kindle. Book excerpt: Tools are needed to define, measure and assess pollution in processes and products, to direct and measure improvements in designing cleaner processes and products, and to design benign processes and products. Life cycle assessment, process simulation and integration, material substitution and environmental impact assessment are some of these tools. Advances have been made recently in incorporating environmental criteria in process and product design, some renditions of which are commercially available. This is the first compilation of methods, tools and models that can be used to design products and manufacturing processes that prevent pollution from occurring in the first place, rather than treating the wastes after they are formed. There is also a critique of social barriers to pollution prevention. Readership: Scientists and advisors in academia, government and industry engaged in encouraging, enforcing, developing and/or implementing cleaner processes and products.