Download or read book Enhancement of Mechanical and Tribological Properties of Ti 6Al 4V Alloy written by Neda Dalili and published by . This book was released on 2008 with total page 394 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Tribology in Materials and Manufacturing written by Amar Patnaik and published by BoD – Books on Demand. This book was released on 2021-02-03 with total page 348 pages. Available in PDF, EPUB and Kindle. Book excerpt: Tribology in Materials and Manufacturing - Wear, Friction and Lubrication brings an interdisciplinary perspective to accomplish a more detailed understanding of tribological assessments, friction, lubrication, and wear in advanced manufacturing. Chapters cover such topics as ionic liquids, non-textured and textured surfaces, green tribology, lubricants, tribolayers, and simulation of wear.
Download or read book Surface Engineering of Light Alloys written by Hanshan Dong and published by Elsevier. This book was released on 2010-05-24 with total page 681 pages. Available in PDF, EPUB and Kindle. Book excerpt: The growing use of light alloys in industries such as aerospace, sports equipment and biomedical devices is driving research into surface engineering technologies to enhance their properties for the desired end use. Surface engineering of light alloys: Aluminium, magnesium and titanium alloys provides a comprehensive review of the latest technologies for modifying the surfaces of light alloys to improve their corrosion, wear and tribological properties. Part one discusses surface degradation of light alloys with chapters on corrosion behaviour of magnesium alloys and protection techniques, wear properties of aluminium-based alloys and tribological behaviour of titanium alloys. Part two reviews surface engineering technologies for light alloys including anodising, plasma electrolytic oxidation, thermal spraying, cold spraying, physical vapour deposition, plasma assisted surface treatment, PIII/PSII treatments, laser surface modification, ceramic conversion and duplex treatments. Part three covers applications for surface engineered light alloys including sports equipment, biomedical devices and plasma electrolytic oxidation and anodised aluminium alloys for spacecraft applications. With its distinguished editor and international team of contributors, Surface engineering of light alloys: Aluminium, magnesium and titanium alloys is a standard reference for engineers, metallurgists and materials scientists looking for a comprehensive source of information on surface engineering of aluminium, magnesium and titanium alloys. Discusses surface degradation of light alloys considering corrosion behaviour and wear and tribological properties Examines surface engineering technologies and modification featuring plasma electrolytic oxidation treatments and both thermal and cold spraying Reviews applications for engineered light alloys in sports equipment, biomedical devices and spacecraft
Download or read book Development of Tantalum Oxide TA O Thin Film Coating on Biomedical TI 6AL 4V Alloy to Enhance Mechanical and Tribological Properties and Biocompatibilty written by Bizhan Rahmati and published by . This book was released on 2016 with total page 368 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Titanium Alloys written by Maciej Motyka and published by BoD – Books on Demand. This book was released on 2019-11-27 with total page 156 pages. Available in PDF, EPUB and Kindle. Book excerpt: Titanium alloys, due to unique physical and chemical properties (mainly high relative strength combined with very good corrosion resistance), are considered as an important structural metallic material used in hi-tech industries (e.g. aerospace, space technology). This book provides information on new manufacturing and processing methods of single- and two-phase titanium alloys. The eight chapters of this book are distributed over four sections. The first section (Introduction) indicates the main factors determining application areas of titanium and its alloys. The second section (Manufacturing, two chapters) concerns modern production methods for titanium and its alloys. The third section (Thermomechanical and surface treatment, three chapters) covers problems of thermomechanical processing and surface treatment used for single- and two-phase titanium alloys. The fourth section (Machining, two chapters) describes the recent results of high speed machining of Ti-6Al-4V alloy and the possibility of application of sustainable machining for titanium alloys.
Download or read book Titanium and Titanium Alloys written by Christoph Leyens and published by John Wiley & Sons. This book was released on 2006-03-06 with total page 532 pages. Available in PDF, EPUB and Kindle. Book excerpt: This handbook is an excellent reference for materials scientists and engineers needing to gain more knowledge about these engineering materials. Following introductory chapters on the fundamental materials properties of titanium, readers will find comprehensive descriptions of the development, processing and properties of modern titanium alloys. There then follows detailed discussion of the applications of titanium and its alloys in aerospace, medicine, energy and automotive technology.
Download or read book Cold Spray Technology written by Anatolii Papyrin and published by Elsevier. This book was released on 2006-10-04 with total page 341 pages. Available in PDF, EPUB and Kindle. Book excerpt: The topic of this book is Cold Spray technology. Cold Spray is a process of applying coatings by exposing a metallic or dielectric substrate to a high velocity (300 to 1200 m/s) jet of small (1 to 50 μm) particles accelerated by a supersonic jet of compressed gas. This process is based on the selection of the combination of particle temperature, velocity, and size that allows spraying at the lowest temperature possible. In the Cold Spray process, powder particles are accelerated by the supersonic gas jet at a temperature that is always lower than the melting point of the material, resulting in coating formation from particles in the solid state. As a consequence, the deleterious effects of high-temperature oxidation, evaporation, melting, crystallization, residual stresses, gas release, and other common problems for traditional thermal spray methods are minimized or eliminated. This book is the first of its kind on the Cold Spray process. Cold Spray Technology covers a wide spectrum of various aspects of the Cold Spray technology, including gas-dynamics, physics of interaction of high-speed solid particles with a substrate as well as equipment, technologies, and applications. Cold Spray Technology includes the results of more than 20 years of original studies (1984-2005) conducted at the Institute of Theoretical and Applied Mechanics of the Siberian Division of the Russian Academy of Science, as well as the results of studies conducted at most of the research centres around the world. The authors' goal is threefold. The first goal is to explain basic principles and advantages of the Cold Spray process. The second goal is, to give practical information on technologies and equipment. The third goal is to present the current state of research and development in this field over the world. The book provides coverage and data that will be of interest for users of Cold Spray technology as well as for other coating experts. At the present time the Cold Spray method is recognized by world leading scientists and specialists. A wide spectrum of research is being conducted at many research centres and companies in many countries. New approach to spray coatings Results are exceptionally pure coatings Low spray temperature without degradation of powder and substrate materials High productivity, high deposition efficiency High operational safety because of absence of high temperature gas jets, radiation and explosive gases Excellent thermal and electrical conductivity Wide spectrum of applications because of important advantages of the process
Download or read book Tribology of Ti 6Al 4V Alloy Manufactured by Additive Manufacturing written by Auezhan Amanov and published by . This book was released on 2020 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: In this study, the influence of ultrasonic nanocrystal surface modification (UNSM), which was applied as a post-additive manufacturing (AM), in terms of surface, tensile and tribological properties of Ti-6Al-4V alloy by selective laser melting (SLM) was investigated. Ti-6Al-4V alloy was subjected to UNSM at room and high temperatures (RT and HT). It was found that the UNSM enhanced the strength and reduced the roughness of the as-SLM sample, where both increased with increasing UNSM temperature. The UNSM bore influence on tribological properties, where the friction coefficient of the as-SLM sample reduced by about 25.8% and 305% and the wear resistance enhanced by about 41% and 246% at RT and HT, respectively. These are essentially attributed to the enhanced strength, smoothed surface and expelled pores from the surface. Based on SEM images, the damage caused by abrasive wear was the most observed in the wear track of the as-SLM sample than was caused by the highest wear rate. The UNSM temperature-dependent wear mechanisms were comprehensively investigated and elaborated based on the obtained experimental data and observed microstructural images. Indeed, a further investigation is required to improve the characteristics of as-SLM Ti-6Al-4V alloy to the wrought level due to the replacement possibility.
Download or read book Machining of Titanium Alloys written by J. Paulo Davim and published by Springer. This book was released on 2014-07-05 with total page 154 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a collection of examples illustrating the resent research advances in the machining of titanium alloys. These materials have excellent strength and fracture toughness as well as low density and good corrosion resistance; however, machinability is still poor due to their low thermal conductivity and high chemical reactivity with cutting tool materials. This book presents solutions to enhance machinability in titanium-based alloys and serves as a useful reference to professionals and researchers in aerospace, automotive and biomedical fields.
Download or read book Proceedings of Asia International Conference on Tribology 2018 written by Mohd Fadzli Bin Abdollah and published by Malaysian Tribology Society. This book was released on 2018-09-17 with total page 540 pages. Available in PDF, EPUB and Kindle. Book excerpt: This ebook is a compilation of 234 papers presented at the 6th Asia International Conference on Tribology (ASIATRIB2018): Kuching, Sarawak - Malaysia from 17 to 20 September 2018.
Download or read book Titanium Alloys written by Jan Sieniawski and published by BoD – Books on Demand. This book was released on 2013-05-15 with total page 160 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book contains six chapters and covers topics dealing with biomedical applications of titanium alloys, surface treatment, relationships between microstructure and mechanical and technological properties, and the effect of radiation on the structure of the titanium alloys.
Download or read book Tribology and Surface Engineering for Industrial Applications written by Catalin I. Pruncu and published by CRC Press. This book was released on 2021-11-23 with total page 271 pages. Available in PDF, EPUB and Kindle. Book excerpt: Tribology is a multidisciplinary science that encompasses mechanical engineering, materials science, surface engineering, lubricants, and additives chemistry with tremendous applications. Tribology and Surface Engineering for Industrial Applications discusses the latest in tribology and surface engineering for industrial applications. This book: Offers information on coatings and surface diagnostics Explains a variety of techniques for improved performance Describes applications in automotive, wheel and rail materials, manufacturing, and wind turbines Written for researchers and advanced students, this book encompasses a wide-ranging view of the latest in industrial applications of tribology and surface engineering for a variety of cross-disciplinary applications.
Download or read book Titanium in Medical and Dental Applications written by Francis Froes and published by Woodhead Publishing. This book was released on 2018-05-09 with total page 656 pages. Available in PDF, EPUB and Kindle. Book excerpt: Titanium in Medical and Dental Applications is an essential reference book for those involved in biomedical materials and advanced metals. Written by well-known experts in the field, it covers a broad array of titanium uses, including implants, instruments, devices, the manufacturing processes used to create them, their properties, corrosion resistance and various fabrication approaches. Biomedical titanium materials are a critically important part of biomaterials, especially in cases where non-metallic biomedical materials are not suited to applications, such as the case of load-bearing implants. The book also covers the use of titanium for implants in the medical and dental fields and reviews the use of titanium for medical instruments and devices. Provides an understanding of the essential and broad applications of Titanium in both the medical and dental industries Discusses the pathways to manufacturing titanium into critical biomedical and dental devices Includes insights into further applications within the industry
Download or read book Mechanics of Biomaterials written by Lisa A. Pruitt and published by Cambridge University Press. This book was released on 2011-10-20 with total page 699 pages. Available in PDF, EPUB and Kindle. Book excerpt: Combining materials science, mechanics, implant design and clinical applications, this self-contained text provides a complete grounding to the field.
Download or read book Manufacturing Engineering written by Vishal S. Sharma and published by Springer. This book was released on 2019-03-05 with total page 202 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents selected proceedings of the International Conference on Production and Industrial Engineering (CPIE) 2018. Focusing on recent developments in the field of production and manufacturing engineering, it provides solutions to wide-ranging contemporary problems in manufacturing engineering and other allied areas using analytical models and the latest numerical approaches. The topics covered in this book include conventional and non conventional machining, casting, welding, materials and processing. As such it is useful to academics, researchers and practitioners working in the field of manufacturing and production engineering.
Download or read book Tribocorrosion written by Anna Igual Munoz and published by Springer Nature. This book was released on 2020-06-16 with total page 110 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is a toolbox for identifying and addressing tribocorrosion situations from an engineering point of view. It is an accessible and introductory guideline to the emerging and interdisciplinary field of tribocorrosion covering the main concepts of tribology and corrosion. It describes specific tribocorrosion concepts, models and experimental techniques as well as their application to practical situations in which mechanical and chemical phenomena act simultaneously.
Download or read book Dissimilar Metal Welding written by Pierpaolo Carlone and published by MDPI. This book was released on 2019-12-12 with total page 288 pages. Available in PDF, EPUB and Kindle. Book excerpt: The combination of distinct materials is a key issue in modern industry, whereas the driving concept is to design parts with the right material in the right place. In this framework, a great deal of attention is directed towards dissimilar welding and joining technologies. In the automotive sector, for instance, the concept of “tailored blanks”, introduced in the last decade, has further highlighted the necessity to weld dissimilar materials. As far as the aeronautic field is concerned, most structures are built combining very different materials and alloys, in order to match lightweight and structural performance requirements. In this framework, the application of fusion welding techniques, namely, tungsten inert gas or laser welding, is quite challenging due to the difference in physical properties, in particular the melting point, between adjoining materials. On the other hand, solid-state welding methods, such as the friction stir welding as well as linear friction welding processes, have already proved to be capable of manufacturing sound Al-Cu, Al-Ti, Al-SS, and Al-Mg joints, to cite but a few. Recently, promising results have also been obtained using hybrid methods. Considering the novelty of the topic, many relevant issues are still open, and many research groups are continuously publishing valuable results. The aim of this book is to finalize the latest contributions on this topic.
