Download or read book Electronic Control Systems written by Ross T Bannatyne and published by SAE International. This book was released on 2003-01-08 with total page 90 pages. Available in PDF, EPUB and Kindle. Book excerpt: Electronic Control Systems describes the evolution of electronic control systems and examines growth experienced in the four main system categories - safety and convenience, powertrain, body controls, and entertainment and communications. The system trends and technologies are covered in detail. The report concludes with a summary of the challenges, changes on the horizon, and a discussion of how sustainable competitive advantage can perhaps be achieved.
Download or read book Sliding Mode Controllers for Power Electronic Converters written by Axaykumar Mehta and published by Springer. This book was released on 2018-12-13 with total page 95 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book proposes a proportional integral type sliding function, which does not facilitate the finite reaching and hence the responses of the load voltage results in an exponential steady state. To facilitate finite time reaching, it also presents the new Integral Sliding Mode Control with Finite Time Reaching (ISMCFTR). The book also extends the application of the proposed controller to another type of PEC, the DC-DC Boost converter, and also proposes the PI type sliding surface for the Zeta converter, which is non-inverting type Buck Boost converter. An important source of practical implementations, it presents practical implementations as simulation and experimental results to demonstrate the efficacy of the converter.
Download or read book Electronic Access Control written by Thomas L. Norman and published by Elsevier. This book was released on 2011-09-26 with total page 445 pages. Available in PDF, EPUB and Kindle. Book excerpt: Electronic Access Control introduces the fundamentals of electronic access control through clear, well-illustrated explanations. Access Control Systems are difficult to learn and even harder to master due to the different ways in which manufacturers approach the subject and the myriad complications associated with doors, door frames, hardware, and electrified locks. This book consolidates this information, covering a comprehensive yet easy-to-read list of subjects that every Access Control System Designer, Installer, Maintenance Tech or Project Manager needs to know in order to develop quality and profitable Alarm/Access Control System installations. Within these pages, Thomas L. Norman – a master at electronic security and risk management consulting and author of the industry reference manual for the design of Integrated Security Systems – describes the full range of EAC devices (credentials, readers, locks, sensors, wiring, and computers), showing how they work, and how they are installed. A comprehensive introduction to all aspects of electronic access control Provides information in short bursts with ample illustrations Each chapter begins with outline of chapter contents and ends with a quiz May be used for self-study, or as a professional reference guide
Download or read book Dynamics and Control of Switched Electronic Systems written by Francesco Vasca and published by Springer Science & Business Media. This book was released on 2012-03-30 with total page 493 pages. Available in PDF, EPUB and Kindle. Book excerpt: The increased efficiency and quality constraints imposed on electrical energy systems have inspired a renewed research interest in the study of formal approaches to the analysis and control of power electronics converters. Switched systems represent a useful framework for modeling these converters and the peculiarities of their operating conditions and control goals justify the specific classification of “switched electronic systems”. Indeed, idealized switched models of power converters introduce problems not commonly encountered when analyzing generic switched models or non-switched electrical networks. In that sense the analysis of switched electronic systems represents a source for new ideas and benchmarks for switched and hybrid systems generally. Dynamics and Control of Switched Electronic Systems draws on the expertise of an international group of expert contributors to give an overview of recent advances in the modeling, simulation and control of switched electronic systems. The reader is provided with a well-organized source of references and a mathematically-based report of the state of the art in analysis and design techniques for switched power converters. Intuitive language, realistic illustrative examples and numerical simulations help the reader to come to grips with the rigorous presentation of many promising directions of research such as: converter topologies and modulation techniques; continuous-time, discrete-time and hybrid models; modern control strategies for power converters; and challenges in numerical simulation. The guidance and information imparted in this text will be appreciated by engineers, and applied mathematicians working on system and circuit theory, control systems development, and electronic and energy conversion systems design.
Download or read book Protecting Industrial Control Systems from Electronic Threats written by Joseph Weiss and published by Momentum Press. This book was released on 2010 with total page 340 pages. Available in PDF, EPUB and Kindle. Book excerpt: Aimed at both the novice and expert in IT security and industrial control systems (ICS), this book will help readers gain a better understanding of protecting ICSs from electronic threats. Cyber security is getting much more attention and "SCADA security" (Supervisory Control and Data Acquisition) is a particularly important part of this field, as are Distributed Control Systems (DCS), Programmable Logic Controllers (PLCs), Remote Terminal Units (RTUs), Intelligent Electronic Devices (IEDs), and all the other, field controllers, sensors, drives, and emission controls that make up the "intelligence" of modern industrial buildings and facilities. Some Key Features include: How to better understand the convergence between Industrial Control Systems (ICS) and general IT systems Insight into educational needs and certifications How to conduct Risk and Vulnerability Assessments Descriptions and observations from malicious and unintentional ICS cyber incidents Recommendations for securing ICS
Download or read book FCS Electronic Control Digital Electronics L3 written by Julia Pilbeam and published by Pearson South Africa. This book was released on 2008 with total page 274 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Electronic Control Systems written by Ross T Bannatyne and published by SAE International. This book was released on 2003-01-08 with total page 90 pages. Available in PDF, EPUB and Kindle. Book excerpt: Electronic Control Systems describes the evolution of electronic control systems and examines growth experienced in the four main system categories - safety and convenience, powertrain, body controls, and entertainment and communications. The system trends and technologies are covered in detail. The report concludes with a summary of the challenges, changes on the horizon, and a discussion of how sustainable competitive advantage can perhaps be achieved.
Download or read book Power Electronic Control in Electrical Systems written by Enrique Acha and published by Newnes. This book was released on 2002-01-08 with total page 464 pages. Available in PDF, EPUB and Kindle. Book excerpt: Within this book the fundamental concepts associated with the topic of power electronic control are covered alongside the latest equipment and devices, new application areas and associated computer-assisted methods. *A practical guide to the control of reactive power systems *Ideal for postgraduate and professional courses *Covers the latest equipment and computer-aided analysis.
Download or read book Electronic Controllers written by Lawrence M. Thompson and published by . This book was released on 1989 with total page 104 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Control of Power Electronic Converters and Systems written by Frede Blaabjerg and published by Academic Press. This book was released on 2018-04-27 with total page 532 pages. Available in PDF, EPUB and Kindle. Book excerpt: Control of Power Electronic Converters, Volume Two gives the theory behind power electronic converter control and discusses the operation, modelling and control of basic converters. The main components of power electronics systems that produce a desired effect (energy conversion, robot motion, etc.) by controlling system variables (voltages and currents) are thoroughly covered. Both small (mobile phones, computer power supplies) and very large systems (trains, wind turbines, high voltage power lines) and their power ranges, from the Watt to the Gigawatt, are presented and explored. Users will find a focused resource on how to apply innovative control techniques for power converters and drives. Discusses different applications and their control Explains the most important controller design methods, both in analog and digital Describes different, but important, applications that can be used in future industrial products Covers voltage source converters in significant detail Demonstrates applications across a much broader context
Download or read book Electronic Control of Switched Reluctance Machines written by TJE Miller and published by Elsevier. This book was released on 2001-05-18 with total page 272 pages. Available in PDF, EPUB and Kindle. Book excerpt: Switched reluctance motors have steadily increased in commercial importance since their introduction in the early 1980's, while their technology - especially of their electronic control - has made great progress. Their unique characteristics introduce a delicate balance, in which the copper and iron are diminished in quantity, complexity and cost, in favour of a greater reliance on sophistication in the controller. Thus mastery of the control is the key challenge in the application of these machines. This book is intended for engineer's in industry and in the large research community in electrical machines and drives. It introduces the techniques for controlling switched reluctance machines, starting from first principles and building up to the most advanced forms of sensorless control. It covers the recent advances in electronic control and includes aspects of motion control, automation, acoustic noise reduction and energy efficiency. Covers the recent changes in control technology Includes up-to-date equipment and methods Contains applications and case studies
Download or read book Power Electronic Converters Modeling and Control written by Seddik Bacha and published by Springer Science & Business Media. This book was released on 2013-11-12 with total page 469 pages. Available in PDF, EPUB and Kindle. Book excerpt: Modern power electronic converters are involved in a very broad spectrum of applications: switched-mode power supplies, electrical-machine-motion-control, active power filters, distributed power generation, flexible AC transmission systems, renewable energy conversion systems and vehicular technology, among them. Power Electronics Converters Modeling and Control teaches the reader how to analyze and model the behavior of converters and so to improve their design and control. Dealing with a set of confirmed algorithms specifically developed for use with power converters, this text is in two parts: models and control methods. The first is a detailed exposition of the most usual power converter models: · switched and averaged models; · small/large-signal models; and · time/frequency models. The second focuses on three groups of control methods: · linear control approaches normally associated with power converters; · resonant controllers because of their significance in grid-connected applications; and · nonlinear control methods including feedback linearization, stabilizing, passivity-based, and variable-structure control. Extensive case-study illustration and end-of-chapter exercises reinforce the study material. Power Electronics Converters Modeling and Control addresses the needs of graduate students interested in power electronics, providing a balanced understanding of theoretical ideas coupled with pragmatic tools based on control engineering practice in the field. Academics teaching power electronics will find this an attractive course text and the practical points make the book useful for self tuition by engineers and other practitioners wishing to bring their knowledge up to date.
Download or read book Integrated Power Electronic Converters and Digital Control written by Ali Emadi and published by CRC Press. This book was released on 2017-12-19 with total page 365 pages. Available in PDF, EPUB and Kindle. Book excerpt: Because of the demand for higher efficiencies, smaller output ripple, and smaller converter size for modern power electronic systems, integrated power electronic converters could soon replace conventional switched-mode power supplies. Synthesized integrated converters and related digital control techniques address problems related to cost, space, flexibility, energy efficiency, and voltage regulation—the key factors in digital power management and implementation. Meeting the needs of professionals working in power electronics, as well as advanced engineering students, Integrated Power Electronic Converters and Digital Control explores the many benefits associated with integrated converters. This informative text details boost type, buck type, and buck-boost type integrated topologies, as well as other integrated structures. It discusses concepts behind their operation as well specific applications. Topics discussed include: Isolated DC-DC converters such as flyback, forward, push-pull, full-bridge, and half-bridge Power factor correction and its application Definition of the integrated switched-mode power supplies Steady-state analysis of the boost integrated flyback rectifier energy storage converter Dynamic analysis of the buck integrated forward converter Digital control based on the use of digital signal processors (DSPs) With innovations in digital control becoming ever more pervasive, system designers continue to introduce products that integrate digital power management and control integrated circuit solutions, both hybrid and pure digital. This detailed assessment of the latest advances in the field will help anyone working in power electronics and related industries stay ahead of the curve.
Download or read book Advanced Control of Electrical Drives and Power Electronic Converters written by Jacek Kabziński and published by Springer. This book was released on 2016-09-30 with total page 378 pages. Available in PDF, EPUB and Kindle. Book excerpt: This contributed volume is written by key specialists working in multidisciplinary fields in electrical engineering, linking control theory, power electronics, artificial neural networks, embedded controllers and signal processing. The authors of each chapter report the state of the art of the various topics addressed and present results of their own research, laboratory experiments and successful applications. The presented solutions concentrate on three main areas of interest: · motion control in complex electromechanical systems, including sensorless control; · fault diagnosis and fault tolerant control of electric drives; · new control algorithms for power electronics converters. The chapters and the complete book possess strong monograph attributes. Important practical and theoretical problems are deeply and accurately presented on the background of an exhaustive state-of the art review. Many results are completely new and were never published before. Well-known control methods like field oriented control (FOC) or direct torque control (DTC) are referred as a starting point for modifications or are used for comparison. Among numerous control theories used to solve particular problems are: nonlinear control, robust control, adaptive control, Lyapunov techniques, observer design, model predictive control, neural control, sliding mode control, signal filtration and processing, fault diagnosis, and fault tolerant control.
Download or read book Power Electronics Drives and Advanced Applications written by Vinod Kumar and published by CRC Press. This book was released on 2020-03-27 with total page 690 pages. Available in PDF, EPUB and Kindle. Book excerpt: Concern for reliable power supply and energy-efficient system design has led to usage of power electronics-based systems, including efficient electric power conversion and power semiconductor devices. This book provides integration of complete fundamental theory, design, simulation and application of power electronics, and drives covering up-to-date subject components. It contains twenty-one chapters arranged in four sections on power semiconductor devices, basic power electronic converters, advanced power electronics converters, power supplies, electrical drives and advanced applications. Aimed at senior undergraduate and graduate students in electrical engineering and power electronics including related professionals, this book • Includes electrical drives such as DC motor, AC motor, special motor, high performance motor drives, solar, electrical/hybrid vehicle and fuel cell drives • Reviews advances in renewable energy technologies (wind, PV, hybrid power systems) and their integration • Explores topics like distributed generation, microgrid, and wireless power transfer system • Includes simulation examples using MATLAB®/Simulink and over four hundred solved, unsolved and review problems
Download or read book Proceedings of Symposium on Power Electronic and Renewable Energy Systems Control written by Sankarsan Mohapatro and published by Springer Nature. This book was released on 2021-07-09 with total page 514 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book includes high-quality research papers presented at Symposium on Power Electronic and Renewable Energy Systems Control (PERESC 2020), which is held at the School of Electrical Sciences, IIT Bhubaneswar, Odisha, India, during 4–5 December 2020. The book covers original work in power electronics which has greatly enabled integration of renewable and distributed energy systems, control of electric machine drives, high voltage system control and operation. The book is highly useful for academicians, engineers, researchers and students to be familiar with the latest state of the art in power electronics technology and its applications.
Download or read book Programming and Application of a DSP to Control and Regulate Power Electronic Converters Programming in C written by Baris Bagci and published by Anchor Academic Publishing (aap_verlag). This book was released on 2014-03-19 with total page 149 pages. Available in PDF, EPUB and Kindle. Book excerpt: The purpose of this project has been to study, operate and program the 32-bit 150MIPS TMS320F2812 DSP developed by Texas Instruments Inc. In addition, it has also been a goal to implement fast estimation techniques for control of resonant converters. For this purpose, PWM signals that are generated using this DSP are used. The demands on the system and the hardware to solve the problem were already decided when I started the work. The algorithms were programmed in C/C++ language, compiled, debugged and transferred to the DSP development board in a compiling and simulation tool (downloader), called CCS (Code Composer Studio v2), also provided by Texas Instruments. In the first chapters of this study I give general information about control systems, digital signal processors, digital signal processing and the DSP used in this work. The following chapters tell about PWM, how to configure the PWM outputs and some examples related with PWM signals are given. After a short review of series resonant converters, I presented the last example implemented in this project. I conclude with a summary and provide some hints of future work.
