Download or read book Electrochemical Water Oxidation at Iron III Oxide Electrodes written by Sandra Haschke and published by . This book was released on 2015 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Sandra Haschke presents a strategy to enhance the Fe2O3 electrode performance by controlled nanostructuring of the catalyst surface, based on anodized aluminum oxide coated by means of atomic layer deposition. Furthermore, she investigates the influence of underlying conductive layers and post-deposition annealing on the electrode performance and the associated changes in morphology and chemical composition. Exploiting all effects combined delivers an increase in steady-state water oxidation throughput by a factor of 2.5 with respect to planar electrodes. Contents Preparation of Nanostructured Fe2O3 Electrodes Chemical and Structural Properties of Nanoporous Catalyst Electrodes Modification of Nanostructured Fe2O3 Electrodes by Means of Post-Deposition Annealing Improvement of Electrode Performance by Surface Area Enhancement Target Groups Researchers and students in the fields of electrochemistry, materials sciences and physical chemistry Practitioners in these areas The Author Sandra Haschke obtained her Master's degree in chemistry at the Friedrich-Alexander University Erlangen-Nürnberg under the supervision of Prof. Dr. Julien Bachmann where she will continue with her PhD thesis.
Download or read book Electrochemical Water Oxidation at Iron III Oxide Electrodes written by Sandra Haschke and published by Springer. This book was released on 2015-03-18 with total page 65 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sandra Haschke presents a strategy to enhance the Fe2O3 electrode performance by controlled nanostructuring of the catalyst surface, based on anodized aluminum oxide coated by means of atomic layer deposition. Furthermore, she investigates the influence of underlying conductive layers and post-deposition annealing on the electrode performance and the associated changes in morphology and chemical composition. Exploiting all effects combined delivers an increase in steady-state water oxidation throughput by a factor of 2.5 with respect to planar electrodes.
Download or read book The Iron Oxides written by Rochelle M. Cornell and published by John Wiley & Sons. This book was released on 2006-12-13 with total page 703 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book brings together in one, compact volume all aspects of the available information about the iron oxides. It presents a coherent, up to date account of the properties, reactions and mechanisms of formation of these compounds. In addition, there are chapters dealing with iron oxides in rocks and soils, as biominerals and as corrosion products together with methods of synthesis and the numerous application of these compounds. Their role in the environment is also discussed. The authors are experts in the field of iron oxides and have worked on all the topics covered. Much recent data from the authors' own laboratories is included and opportunities for further research are indicated. Special features are the electron micrographs and colour plates together with the many different spectra used to illustrate properties and aspects of behaviour. Numerous tables and graphs enable trends and relationships to be seen at a glance. The book concludes with an extensive bibliography. This book should prove invaluable to industry and to all researchers who, whatever their background and level of experience, are interested in this rapidly expanding field. It is an essential volume for any scientific library and is now in its second, completely revised and extended edition!
Download or read book Comprehensive Treatise of Electrochemistry written by John Bockris and published by Springer Science & Business Media. This book was released on 2013-03-09 with total page 632 pages. Available in PDF, EPUB and Kindle. Book excerpt: It is now time for a comprehensive treatise to look at the whole field of electrochemistry. The present treatise was conceived in 1974, and the earliest invitations to authors for contributions were made in 1975. The completion of the early volumes has been delayed by various factors. There has been no attempt to make each article emphasize the most recent situation at the expense of an overall statement of the modern view. This treatise is not a collection of articles from Recent Advances in Electrochemistry or Modern Aspects of Electrochemistry. It is an attempt at making a mature statement about the present position in the vast area of what is best looked at as a new interdisciplinary field. Texas A & M University J. O'M. Bockris University of Ottawa B. E. Conway Case Western Reserve University Ernest Yeager & M University Texas A Ralph E. White Preface to Volume 2 This volume brings together some dozen processes well known to the electro chemist and treats them according to their various degrees of importance. The production of hydrogen is one of the more important processes, particularly with respect to the prospects of a hydrogen economy. No one would doubt, however, that the most commercially important electrochemical processes at the present time are the production of aluminum and of chlorine. Each of these processes has a separate chapter devoted to it.
Download or read book The Effect of Anions on the Electrochemical Oxidation of Iron II Ion at Platinum Electrodes written by Robert Earl Graves and published by . This book was released on 1972 with total page 268 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book PEM Electrolysis for Hydrogen Production written by Dmitri Bessarabov and published by CRC Press. This book was released on 2016-02-03 with total page 401 pages. Available in PDF, EPUB and Kindle. Book excerpt: An ever-increasing dependence on green energy has brought on a renewed interest in polymer electrolyte membrane (PEM) electrolysis as a viable solution for hydrogen production. While alkaline water electrolyzers have been used in the production of hydrogen for many years, there are certain advantages associated with PEM electrolysis and its relevan
Download or read book Photoelectrochemical Hydrogen Production written by Roel van de Krol and published by Springer Science & Business Media. This book was released on 2011-11-09 with total page 322 pages. Available in PDF, EPUB and Kindle. Book excerpt: Photoelectrochemical Hydrogen Production describes the principles and materials challenges for the conversion of sunlight into hydrogen through water splitting at a semiconducting electrode. Readers will find an analysis of the solid state properties and materials requirements for semiconducting photo-electrodes, a detailed description of the semiconductor/electrolyte interface, in addition to the photo-electrochemical (PEC) cell. Experimental techniques to investigate both materials and PEC device performance are outlined, followed by an overview of the current state-of-the-art in PEC materials and devices, and combinatorial approaches towards the development of new materials. Finally, the economic and business perspectives of PEC devices are discussed, and promising future directions indicated. Photoelectrochemical Hydrogen Production is a one-stop resource for scientists, students and R&D practitioners starting in this field, providing both the theoretical background as well as useful practical information on photoelectrochemical measurement techniques. Experts in the field benefit from the chapters on current state-of-the-art materials/devices and future directions.
Download or read book 1 Dimensional Metal Oxide Nanostructures written by Zainovia Lockman and published by CRC Press. This book was released on 2018-12-07 with total page 331 pages. Available in PDF, EPUB and Kindle. Book excerpt: 1-D metal oxide nanostructures, especially those with semiconducting properties, have attracted much attention in recent years due to their potential and emerging applications, specifically in environment purification and energy devices. For these applications, there have been many efforts to grow 1-D nanostructures in the form of nanotubes, nanorods, and nanowires using processes that conserve energy, are cost effective, and can be scaled up for large-scale production. 1-Dimensional Metal Oxide Nanostructures gathers under one title the most recent development of oxide nanomaterials, especially those fabricated via oxidation process in the nanoscale field. Thermal and anodic oxidation processes are reviewed with an aim to offer an in-depth understanding of mechanisms of 1-D nanostructure formation, their characteristics, and limitations. Other more common methods are also discussed, including sol-gel, hydrothermal, and other templated methods. Important applications of 1-D nanostructures are then presented, focusing on oxides like zinc oxide, titanium oxide, zirconium oxide, copper oxide, and iron oxide. A chapter on carbon nanotubes hybrid with these oxides is also included as well as one on silicon oxide nanowires formation by local anodic oxidation process. Aimed at researchers, academics, and engineers working across the fields of nanotechnology, materials science, chemistry, physics, semiconductors, and environmental and biomedical engineering, this essential reference enables readers to grasp the main concepts of nanomaterials in 1-D: formation technique, characteristics, and uses. It also encourages practical innovations in nanotechnology, especially in curbing pressing global issues related to energy, environment, and security.
Download or read book Photo and Electro Catalytic Processes written by Jianmin Ma and published by John Wiley & Sons. This book was released on 2022-01-25 with total page 596 pages. Available in PDF, EPUB and Kindle. Book excerpt: Explore green catalytic reactions with this reference from a renowned leader in the field Green reactions—like photo-, photoelectro-, and electro-catalytic reactions—offer viable technologies to solve difficult problems without significant damage to the environment. In particular, some gas-involved reactions are especially useful in the creation of liquid fuels and cost-effective products. In Photo- and Electro-Catalytic Processes: Water Splitting, N2 Fixing, CO2 Reduction, award-winning researcher Jianmin Ma delivers a comprehensive overview of photo-, electro-, and photoelectron-catalysts in a variety of processes, including O2 reduction, CO2 reduction, N2 reduction, H2 production, water oxidation, oxygen evolution, and hydrogen evolution. The book offers detailed information on the underlying mechanisms, costs, and synthetic methods of catalysts. Filled with authoritative and critical information on green catalytic processes that promise to answer many of our most pressing energy and environmental questions, this book also includes: Thorough introductions to electrocatalytic oxygen reduction and evolution reactions, as well as electrocatalytic hydrogen evolution reactions Comprehensive explorations of electrocatalytic water splitting, CO2 reduction, and N2 reduction Practical discussions of photoelectrocatalytic H2 production, water splitting, and CO2 reduction In-depth examinations of photoelectrochemical oxygen evolution and nitrogen reduction Perfect for catalytic chemists and photochemists, Photo- and Electro-Catalytic Processes: Water Splitting, N2 Fixing, CO2 Reduction also belongs in the libraries of materials scientists and inorganic chemists seeking a one-stop resource on the novel aspects of photo-, electro-, and photoelectro-catalytic reactions.
Download or read book Alkaline Electrochemical Water Oxidation by NiFe based Metal Oxide Catalysts written by and published by . This book was released on 2015 with total page 101 pages. Available in PDF, EPUB and Kindle. Book excerpt: The oxygen evolution reaction (OER) is the ideal anodic reaction for a photoelectrochemical cell that converts solar energy into chemical fuels; however it is currently limited by catalyst efficiency and cost. In order to overcome these limitations, much effort has been devoted to the discovery of more efficient earth-abundant metal oxide electrocatalysts, particularly mixed-metals oxides, as well as understanding their mechanisms. This thesis addresses both of these challenges. An O2-sensitive fluorescence-based screening assay was developed and arrays of ternary oxide electrocatalysts were examined. Analysis of the intensity of the resulting fluorescence signal allowed for the identification of compositions with high activity. Compositions exhibiting the highest activities were validated through Tafel analyses, and good qualitative agreement was observed between screening results and electrochemical measurements. While Fe is known to improve the activity of Ni oxide catalysts, the incorporation of a third metal into Ni-Fe binary oxides was often observed to further enhance OER activity, with Ni-Fe-Al amorphous oxide showing the highest activity during our initial screening. The previously observed instability led to the investigation of a well-defined NiFeAlO4 inverse spinel oxide as a water oxidation electrocatalyst, where structural analyses confirmed the substitution of Al for Fe lattice sites. A comparison of electrochemical activity against compositionally and structurally relevant oxides, including the known OER catalysts NiO, NiFe 9:1, and NiFe2O4 established NiFeAlO4 as a superior electrocatalyst with no Al leaching, and cyclic voltammograms of the oxides indicated that the electron-withdrawing M+3 ions in the inverse spinels make Ni+2 sites more difficult to oxidize. Furthermore, it was observed that neither of the bimetallic spinel oxides (NiFe2O4 & NiAl2O4) outperformed NiFeAlO4, suggesting a unique synergistic effect between all three metal sites that influences the OER rate determining step. In addition to catalyst discovery, we also pursued mechanistic studies to better understand the dramatic activity enhancement that results when Fe is added to various Ni oxide electrocatalysts. Operando Mössbaurer spectroscopic studies of a 3:1 Ni:Fe layered oxide and anhydrous Fe oxide electrocatalyst was performed. Catalyst materials were prepared by a hydrothermal precipitation method that enabled growth of the oxide catalysts directly on a carbon paper electrode, thereby enhancing charge transport and mechanical stability needed for the operando studies. Fe+4 species are evident in the NiFe-oxide catalyst during steady-state water oxidation, accounting for up to 21% of the total Fe in the catalyst. No Fe+4 is detected under any conditions in the Fe-oxide catalyst. The lifetime of the observed Fe+4 species suggests they do not participate directly in water oxidation; however, their presence has important implications for the promoting effect of Fe in NiFe-oxide electrocatalysts.
Download or read book Anodization fabrication techniques and energy related applications for nanostructured anodic films on transition metals written by Longfei Jiang and published by OAE Publishing Inc.. This book was released on 2022-11-14 with total page 30 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nanostructured anodic films on transition metals prepared using the electrochemical anodization method have recently attracted particular attention owing to their extraordinary properties and potential use in a variety of applications. Herein, we provide a thorough review of the anodization fabrication of anodic films with different nanostructures, including nanopores, nanotubes, nanoflowers, nanoneedles and nanowires on transition metals, focusing on the growth processes of nanostructured anodic films on three representative transition metals, namely, iron, copper and zinc. Specific consideration is given to the anodization behavior and formed film nanostructures of these transition metals. We conclude that electrolyte composition plays a key role in influencing the final morphologies of anodic films. Fluoride-containing solutions represent universal electrolytes for forming nanostructured anodic films on transition metals. The main applications of the resulting nanostructured anodic films, especially in energy-related fields, such as photoelectrochemical water splitting and supercapacitors, are also presented and discussed. Finally, we indicate the main challenges associated with the fabrication of anodic films with highly ordered nanostructures and the potential future directions of this field are indicated.
Download or read book Pesticides Remediation Technologies from Water and Wastewater written by Mohammad Hadi Dehghani and published by Elsevier. This book was released on 2022-04-26 with total page 464 pages. Available in PDF, EPUB and Kindle. Book excerpt: Pesticides Remediation Technologies from Water and Wastewater focuses on environmental aspects and health effects of pesticides, the use of conventional and AOPs technologies, and adsorption processes and nanomaterials for the removal of pesticides from water and wastewater. The deterioration of water quality is of great concern due to its effects on aquatic organisms, humans and the ecosystem. Among the pollutants, pesticides are a major concern in villages and farm land. This edited book bridges the gap between old and new knowledge about the categorization of pesticides, the presence of them in water, wastewater, soil and foods, and new methods to detect them from water matrices. This edited book provides the necessary basic knowledge to new researchers who want to learn about pesticides and the ways to eliminate them in aqueous matrices. Moreover, it is also a helpful resource for mature researchers in this field, providing them with new trends in water and wastewater treatment processes, preparation and application of novel adsorbent materials. Includes methods for effectively removing pesticides from potable water and water bodies Provides techniques that are eco-friendly and that do not use toxic chemicals and are lower in cost Presents information needed to identify severe health effects on human beings and aquatic animals
Download or read book Advances in Drinking Water Purification written by Sibdas Bandyopadhyay and published by Elsevier. This book was released on 2024-01-17 with total page 496 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advances in Drinking Water Purification: Small Systems and Emerging Issues captures the knowledge and impact on the performance of various types of water purification technologies and identities the need for further development with a view to carry forward the SDG global targets of achieving safe and affordable drinking water. The book bridges the knowledge gap between various types of treatability options which is essential for selection of suitable treatment systems and augmentation in the desirable levels of specific contaminants. It focuses on providing the scope of selecting location specific technology options by presenting multiple approaches for treatment of most crucial toxic contaminants/pathogens. In addition, it provides insights into the effect of nature of impurities and selection of treatment options on the global quality of drinking water, comprising its possible impacts on the efficiency of the techniques used and thus on the safety of drinking water. This information is indispensable in identifying the appropriate technology depending on the socioeconomic conditions to address the problem of decontamination in drinking water. Discusses point-of-use devices for the removal of organic and inorganic contaminants from drinking water Provides a multipronged approach to encourage, recognize, protect and commercialize available options for water purification Includes case studies for field testing/pilot trials Provides an in-depth analysis on the efficacy of small systems with an emphasis on the sustainability, socio-technical aspects and emerging issues
Download or read book Photoelectrochemical Water Splitting written by Hans-Joachim Lewerenz and published by Royal Society of Chemistry. This book was released on 2013-10-02 with total page 497 pages. Available in PDF, EPUB and Kindle. Book excerpt: There has been a resurgence of interest in light-induced water splitting as the search for storable carbon neutral energy becomes more urgent. Although the history of the basic idea dates back more than four decades, efficient, economical and stable integrated devices have yet to be realized. In the continuing quest for such devices, the field of photoelectrochemistry is entering a new phase where the extraordinary interdisciplinary of the research and development efforts are opening new avenues. This aspect of current research effort is reflected in the chapters of this book, which encompass present thinking in the various disciplines such as materials science, photo-electrochemistry and interfaces that can contribute to realization of viable solar fuel generators. This book presents a blend of the background science and recent advances in the field of photoelectrochemical water splitting, and includes aspects that point towards medium to long term future realization. The content of the book goes beyond the more traditional approaches to the subject by including topics such as novel excitation energy processes that have only been realized so far in advanced photonics. The comprehensive overview of current activities and development horizons provided by the impressive collection of internationally renowned authors therefore represents a unique reflection of current thinking regarding water splitting by light.
Download or read book Natural Organic Matter in Water written by Mika Sillanpaa and published by Butterworth-Heinemann. This book was released on 2022-10-17 with total page 374 pages. Available in PDF, EPUB and Kindle. Book excerpt: Natural Organic Matter in Water: Characterization, Treatment Methods, and Climate Change Impact, Second Edition focuses on advanced filtration and treatment options, as well as processes for reducing disinfection by-products, making it an essential resource on the latest breakthroughs in the characterization, treatment and removal of natural organic matter (NOM) from drinking water. Based on the editor’s years of research and field experience, the book covers general parameters, isolation and concentration, fractionation, composition and structural analysis, and biological testing, along with removal methods such as inorganic coagulants, polyelectrolytes and composite coagulants. In addition, sections cover electrochemical and membranes removal methods such as electrocoagulation, electrochemical oxidation, microfiltration and ultrafiltration, nanofiltration, and membrane fouling. This book is a valuable guide for engineers and researchers looking to integrate methods, processes and technologies to achieve desired affects. Provides a summary of up-to-date information surrounding NOM Presents enhanced knowledge on treatment strategies for the removal of NOM Covers conventional as well as advanced NOM removal methods
Download or read book Molecular Electronic Structures of Transition Metal Complexes I written by David Michael P. Mingos and published by Springer Science & Business Media. This book was released on 2012-01-11 with total page 227 pages. Available in PDF, EPUB and Kindle. Book excerpt: J.P. Dahl: Carl Johan Ballhausen (1926–2010).- J.R. Winkler and H.B. Gray: Electronic Structures of Oxo-Metal Ions.- C.D. Flint: Early Days in Kemisk Laboratorium IV and Later Studies.- J.H. Palmer: Transition Metal Corrole Coordination Chemistry. A Review Focusing on Electronic Structural Studies.- W.C. Trogler: Chemical Sensing with Semiconducting Metal Phthalocyanines.- K.M. Lancaster: Biological Outer-Sphere Coordination.- R.K. Hocking and E.I. Solomon: Ligand Field and Molecular Orbital Theories of Transition Metal X-ray Absorption Edge Transitions.- K.B. Møller and N.E. Henriksen: Time-resolved X-ray diffraction: The dynamics of the chemical bond.
Download or read book Fuel Cell Fundamentals written by Ryan O'Hayre and published by John Wiley & Sons. This book was released on 2016-05-02 with total page 612 pages. Available in PDF, EPUB and Kindle. Book excerpt: A complete, up-to-date, introductory guide to fuel cell technology and application Fuel Cell Fundamentals provides a thorough introduction to the principles and practicalities behind fuel cell technology. Beginning with the underlying concepts, the discussion explores fuel cell thermodynamics, kinetics, transport, and modeling before moving into the application side with guidance on system types and design, performance, costs, and environmental impact. This new third edition has been updated with the latest technological advances and relevant calculations, and enhanced chapters on advanced fuel cell design and electrochemical and hydrogen energy systems. Worked problems, illustrations, and application examples throughout lend a real-world perspective, and end-of chapter review questions and mathematical problems reinforce the material learned. Fuel cells produce more electricity than batteries or combustion engines, with far fewer emissions. This book is the essential introduction to the technology that makes this possible, and the physical processes behind this cost-saving and environmentally friendly energy source. Understand the basic principles of fuel cell physics Compare the applications, performance, and costs of different systems Master the calculations associated with the latest fuel cell technology Learn the considerations involved in system selection and design As more and more nations turn to fuel cell commercialization amidst advancing technology and dropping deployment costs, global stationary fuel cell revenue is expected to grow from $1.4 billion to $40.0 billion by 2022. The sector is forecasted to explode, and there will be a tremendous demand for high-level qualified workers with advanced skills and knowledge of fuel cell technology. Fuel Cell Fundamentals is the essential first step toward joining the new energy revolution.
