Download or read book Effects of Gasoline Reactivity and Ethanol Content on Boosted Premixed and Partially Stratified Low temperature Gasoline Combustion LTGC written by and published by . This book was released on 2015 with total page 21 pages. Available in PDF, EPUB and Kindle. Book excerpt: Low-temperature gasoline combustion (LTGC), based on the compression ignition of a premixed or partially premixed dilute charge, can provide thermal efficiencies (TE) and maximum loads comparable to those of turbo-charged diesel engines, and ultra-low NOx and particulate emissions. Intake boosting is key to achieving high loads with dilute combustion, and it also enhances the fuel's autoignition reactivity, reducing the required intake heating or hot residuals. These effects have the advantages of increasing TE and charge density, allowing greater timing retard with good stability, and making the fuel [Phi]- sensitive so that partial fuel stratification (PFS) can be applied for higher loads and further TE improvements. However, at high boost the autoignition reactivity enhancement can become excessive, and substantial amounts of EGR are required to prevent overly advanced combustion. Accordingly, an experimental investigation has been conducted to determine how the tradeoff between the effects of intake boost varies with fuel-type and its impact on load range and TE. Five fuels are investigated: a conventional AKI=87 petroleum-based gasoline (E0), and blends of 10 and 20% ethanol with this gasoline to reduce its reactivity enhancement with boost (E10 and E20). Furthermore, a second zero-ethanol gasoline with AKI=93 (matching that of E20) was also investigated (CF-E0), and some neat ethanol data are also reported.
Download or read book Characteristics and Control of Low Temperature Combustion Engines written by Rakesh Kumar Maurya and published by Springer. This book was released on 2017-11-03 with total page 553 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book deals with novel advanced engine combustion technologies having potential of high fuel conversion efficiency along with ultralow NOx and particulate matter (PM) emissions. It offers insight into advanced combustion modes for efficient utilization of gasoline like fuels. Fundamentals of various advanced low temperature combustion (LTC) systems such as HCCI, PCCI, PPC and RCCI engines and their fuel quality requirements are also discussed. Detailed performance, combustion and emissions characteristics of futuristic engine technologies such as PPC and RCCI employing conventional as well as alternative fuels are analyzed and discussed. Special emphasis is placed on soot particle number emission characterization, high load limiting constraints, and fuel effects on combustion characteristics in LTC engines. For closed loop combustion control of LTC engines, sensors, actuators and control strategies are also discussed. The book should prove useful to a broad audience, including graduate students, researchers, and professionals Offers novel technologies for improved and efficient utilization of gasoline like fuels; Deals with most advanced and futuristic engine combustion modes such as PPC and RCCI; Comprehensible presentation of the performance, combustion and emissions characteristics of low temperature combustion (LTC) engines; Deals with closed loop combustion control of advanced LTC engines; State-of-the-art technology book that concisely summarizes the recent advancements in LTC technology. .
Download or read book Advanced Combustion Techniques and Engine Technologies for the Automotive Sector written by Akhilendra Pratap Singh and published by Springer Nature. This book was released on 2019-10-10 with total page 256 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book discusses the recent advances in combustion strategies and engine technologies, with specific reference to the automotive sector. Chapters discuss the advanced combustion technologies, such as gasoline direct ignition (GDI), spark assisted compression ignition (SACI), gasoline compression ignition (GCI), etc., which are the future of the automotive sector. Emphasis is given to technologies which have the potential for utilization of alternative fuels as well as emission reduction. One special section includes a few chapters for methanol utilization in two-wheelers and four wheelers. The book will serve as a valuable resource for academic researchers and professional automotive engineers alike.
Download or read book Gasoline Compression Ignition Technology written by Gautam Kalghatgi and published by Springer Nature. This book was released on 2022-01-17 with total page 339 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on gasoline compression ignition (GCI) which offers the prospect of engines with high efficiency and low exhaust emissions at a lower cost. A GCI engine is a compression ignition (CI) engine which is run on gasoline-like fuels (even on low-octane gasoline), making it significantly easier to control particulates and NOx but with high efficiency. The state of the art development to make GCI combustion feasible on practical vehicles is highlighted, e.g., on overcoming problems on cold start, high-pressure rise rates at high loads, transients, and HC and CO emissions. This book will be a useful guide to those in academia and industry.
Download or read book Natural Gas Engines written by Kalyan Kumar Srinivasan and published by Springer. This book was released on 2018-11-03 with total page 428 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers the various advanced reciprocating combustion engine technologies that utilize natural gas and alternative fuels for transportation and power generation applications. It is divided into three major sections consisting of both fundamental and applied technologies to identify (but not limited to) clean, high-efficiency opportunities with natural gas fueling that have been developed through experimental protocols, numerical and high-performance computational simulations, and zero-dimensional, multizone combustion simulations. Particular emphasis is placed on statutes to monitor fine particulate emissions from tailpipe of engines operating on natural gas and alternative fuels.
Download or read book Droplets and Sprays written by Saptarshi Basu and published by Springer. This book was released on 2017-12-11 with total page 433 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on droplets and sprays relevant to combustion and propulsion applications. The book includes fundamental studies on the heating, evaporation and combustion of individual droplets and basic mechanisms of spray formation. The contents also extend to the latest analytical, numerical and experimental techniques for investigating the behavior of sprays in devices like combustion engines and gas turbines. In addition, the book explores several emerging areas like interactions between sprays and flames and the dynamic characteristics of spray combustion systems on the fundamental side, as well as the development of novel fuel injectors for specific devices on the application side. Given its breadth of coverage, the book will benefit researchers and professionals alike.
Download or read book The Effect of Ethanol Addition to Gasoline on Low and Intermediate Temperature Heat Release Under Boosted Conditions in Kinetically Controlled Engines written by David Malcolm Vuilleumier and published by . This book was released on 2016 with total page 181 pages. Available in PDF, EPUB and Kindle. Book excerpt: Abstract The Effect of Ethanol Addition to Gasoline on Low- and Intermediate-Temperature Heat Release under Boosted Conditions in Kinetically Controlled Engines by David Malcolm Vuilleumier Doctor of Philosophy in Mechanical Engineering University of California, Berkeley Professor Jyh-Yuan Chen, Chair The detailed study of chemical kinetics in engines has become required to further advance engine efficiency while simultaneously lowering engine emissions. This push for higher efficiency engines is not caused by a lack of oil, but by efforts to reduce anthropogenic carbon dioxide emissions, that cause global warming. To operate in more efficient manners while reducing traditional pollutant emissions, modern internal combustion piston engines are forced to operate in regimes in which combustion is no longer fully transport limited, and instead is at least partially governed by chemical kinetics of combusting mixtures. Kinetically-controlled combustion allows the operation of piston engines at high compression ratios, with partially-premixed dilute charges; these operating conditions simultaneously provide high thermodynamic efficiency and low pollutant formation. The investigations presented in this dissertation study the effect of ethanol addition on the low-temperature chemistry of gasoline type fuels in engines. These investigations are carried out both in a simplified, fundamental engine experiment, named Homogeneous Charge Compression Ignition, as well as in more applied engine systems, named Gasoline Compression Ignition engines and Partial Fuel Stratification engines. These experimental investigations, and the accompanying modeling work, show that ethanol is an effective scavenger of radicals at low temperatures, and this inhibits the low temperature pathways of gasoline oxidation. Further, the investigations measure the sensitivity of gasoline auto-ignition to system pressure at conditions that are relevant to modern engines. It is shown that at pressures above 40 bar and temperatures below 850 Kelvin, gasoline begins to exhibit Low-Temperature Heat Release. However, the addition of 20% ethanol raises the pressure requirement to 60 bar, while the temperature requirement remains unchanged. These findings have major implications for a range of modern engines. Low-Temperature Heat Release significantly enhances the auto-ignition process, which limits the conditions under which advanced combustion strategies may operate. As these advanced combustion strategies are required to meet emissions and fuel-economy regulations, the findings of this dissertation may benefit and be incorporated into future engine design toolkits, such as detailed chemical kinetic mechanisms.
Download or read book Ignition Behavior of Gasolines and Surrogate Fuels in Low Temperature Combustion Strategies written by Vickey Kalaskar and published by . This book was released on 2015 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: This dissertation discusses the results from three different studies aimed at understanding the importance of fuel chemical structure during low temperature combustion (LTC) strategies, like homogeneous charge compression ignition (HCCI) and partially premixed combustion (PPC) employed in internal combustion (IC) engines wherein the focus is on high octane fuels. Boosted intake air operation combined with exhaust gas recirculation, internal as well as external, has become a standard path for expanding the load limits of IC engines employing LTC strategies mentioned above as well as conventional diesel and spark ignition (SI) engines. However, the effects of fuel compositional variation have not been fully explored. The first study focusses on three different fuels, where each of them were evaluated using a single cylinder boosted HCCI engine using negative valve overlap. The three fuels investigated were: a regular grade gasoline (RON = 90.2), 30% ethanol-gasoline blend (E30, RON = 100.3), and 24% iso-butanol-gasoline blend (IB24, RON = 96.6). Detailed sweeps of intake manifold pressure (atmospheric to 250 kPaa), EGR (0 -- 25% EGR), and injection timing were conducted to identify fuel-specific effects. While significant fuel compositional differences existed, the results showed that all these fuels achieved comparable operation with minor changes in operational conditions. Further, it was shown that the available enthalpy from the exhaust would not be sufficient to satisfy the boost requirements at higher load operation by doing an analysis of the required turbocharger efficiency. While the first study concentrated on load expansion of HCCI, it is important to mention that controlling LTC strategies is difficult under low load or idle operating conditions. To ensure stable operation, fuel injection in the negative valve overlap (NVO) is used as one of method of achieving combustion control. However the combustion chemistry under high temperature and fuel rich conditions that exist during the NVO have not been previously explored. The second study focused on examining the products of fuel rich chemistry as a result of fuel injection in the NVO. In this study, a unique six stroke cycle was used to segregate the exhaust from the NVO and to study the chemistry of the range of fuels injected during NVO under low oxygen conditions. The fuels investigated were methanol, ethanol, iso-butanol, and iso-octane. It was observed that the products of reactions under NVO conditions were highly dependent on the injected fuel's structure with iso-octane producing less than 1.5% hydrogen and methanol producing more than 8%. However a weak dependence was observed on NVO duration and initial temperature, indicating that NVO reforming was kinetically limited. Finally, the experimental trends were compared with CHEMKIN (single zone, 0-D model) predictions using multiple kinetic mechanism that were readily available through literature. Due to the simplicity of the model and inadequate information on the fuel injection process, the experimental data was not modeled well with the mechanisms tested. Some of the shortcomings of the 0-D model were probably due to the model ignoring temperature and composition spatial inhomogeneities and evaporative cooling from fuel vaporization.Though the results from the NVO injection and boosted NVO-HCCI studies are enlightening, the fundamentals of the autoignition behavior of gasoline, alcohols, and their mixtures are not entirely understood despite the interest in high octane fuels in compression engines from a point of view of better thermal efficiency. The third study focused on higher octane blends consisting of binary and ternary mixtures of n-heptane and/or iso-octane, and a fuel of interest. These fuels of interest were toluene, ethanol, and iso-butanol. In this study, the autoignition of such blends is studied under lean conditions ([phi] = 0.25) with varying intake pressure (atmospheric to 3 bar, abs) and at a constant intake temperature of 155 °C. The blends consisted of varying percentages of fuels of interest and their research octane number (RON) approximately estimated at 100 and 80. For comparison, neat iso-octane was selected as RON 100 fuel and PRF 80 blend was selected as RON 80 fuel. It was observed that the blends with a higher percentage of n-heptane showed a stronger tendency to autoignite at lower intake pressures. However, as the intake pressure was increased, the non-reactive components, in this case, the higher octane blend components (toluene, ethanol, and iso-butanol), reduced this tendency subsequently delaying the critical compression ratio (CCR) of the blends. The heat release analysis revealed that the higher octane components in the blends reduced the low temperature reactivity of n-heptane and iso-octane. GC-MS and GC-FID analysis of the partially compressed fuel also indicated that the higher octane components did affect the conversion of the more reactive components, n-heptane and iso-octane, into their partially oxidized branched hydrocarbons in the binary/ternary blends, and reduced the overall reactivity which resulted in a delayed CCR at higher intake pressures.
Download or read book Effect of Premixed Fuel Preparation for Partially Premixed Combustion with a Low Octane Gasoline on a Light Duty Multi Cylinder Compression Ignition Engine written by and published by . This book was released on 2015 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Gasoline compression ignition concepts with the majority of the fuel being introduced early in the cycle are known as partially premixed combustion (PPC). Previous research on single- and multi-cylinder engines has shown that PPC has the potential for high thermal efficiency with low NOx and soot emissions. A variety of fuel injection strategies has been proposed in the literature. These injection strategies aim to create a partially stratified charge to simultaneously reduce NOx and soot emissions while maintaining some level of control over the combustion process through the fuel delivery system. The impact of the direct injection strategy to create a premixed charge of fuel and air has not previously been explored, and its impact on engine efficiency and emissions is not well understood. This paper explores the effect of sweeping the direct injected pilot timing from -91° to -324° ATDC, which is just after the exhaust valve closes for the engine used in this study. During the sweep, the pilot injection consistently contained 65% of the total fuel (based on command duration ratio), and the main injection timing was adjusted slightly to maintain combustion phasing near top dead center. A modern four cylinder, 1.9 L diesel engine with a variable geometry turbocharger, high pressure common rail injection system, wide included angle injectors, and variable swirl actuation was used in this study. The pistons were modified to an open bowl configuration suitable for highly premixed combustion modes. The stock diesel injection system was unmodified, and the gasoline fuel was doped with a lubricity additive to protect the high pressure fuel pump and the injectors. The study was conducted at a fixed speed/load condition of 2000 rpm and 4.0 bar brake mean effective pressure (BMEP). The pilot injection timing sweep was conducted at different intake manifold pressures, swirl levels, and fuel injection GTP-15-1067, Dempsey 2 pressures. The gasoline used in this study has relatively high fuel reactivity with a research octane number of 68. The results of this experimental campaign indicate that the highest brake thermal efficiency and lowest emissions are achieved simultaneously with the earliest pilot injection timings (i.e., during the intake stroke).
Download or read book Partially Premixed Combustion at High Load Using Gasoline and Ethanol a Comparison with Diesel written by Vittorio Manente and published by . This book was released on 2009 with total page 11 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Effects of Ethanol Addition in RON 95 Gasoline on GDI Stratified Combustion written by Loic de Francqueville and published by . This book was released on 2011 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Methanol written by Avinash Kumar Agarwal and published by Springer Nature. This book was released on 2021-05-22 with total page 284 pages. Available in PDF, EPUB and Kindle. Book excerpt: This monograph focuses on methanol and its utilization in transportation sector, namely in spark ignition (SI) engines. The contents focus on methanol production and presents a variety of production technologies from different feedstocks. The potential of methanol utilization in transportation in SI engines is discussed, its challenges, limitations, aspects related to its utilization and current global use of methanol are also presented. The book also contains chapters related to pollutant formation and exhaust emissions from methanol fuelled SI engines, one chapter is focused specifically on formaldehyde emissions, which possesses one of the greatest challenges of methanol use in IC engines. Readers will learn about the production aspects of methanol, its potential as a sustainable fuel, its utilization in SI engine and the effect of methanol and its utilization techniques on engine performance, combustion, exhaust emissions, efficiency and other important parameters. This volume will be a useful guide for professionals, post-graduate students involved in alternative fuels, spark ignition engines, and environmental research.
Download or read book Review of the 21st Century Truck Partnership written by National Research Council and published by National Academies Press. This book was released on 2008-10-19 with total page 130 pages. Available in PDF, EPUB and Kindle. Book excerpt: The 21st Century Truck Partnership (21CTP), a cooperative research and development partnership formed by four federal agencies with 15 industrial partners, was launched in the year 2000 with high hopes that it would dramatically advance the technologies used in trucks and buses, yielding a cleaner, safer, more efficient generation of vehicles. Review of the 21st Century Truck Partnership critically examines and comments on the overall adequacy and balance of the 21CTP. The book reviews how well the program has accomplished its goals, evaluates progress in the program, and makes recommendations to improve the likelihood of the Partnership meeting its goals. Key recommendations of the book include that the 21CTP should be continued, but the future program should be revised and better balanced. A clearer goal setting strategy should be developed, and the goals should be clearly stated in measurable engineering terms and reviewed periodically so as to be based on the available funds.
Download or read book SI Combustion written by and published by . This book was released on 2003 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Dual fuel Reactivity Controlled Compression Ignition RCCI with Alternative Fuels written by and published by . This book was released on 2013 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This research will demonstrate that Reactivity Controlled Compression Ignition (RCCI) has several advantages over other LTC concepts in regards to fuel flexibility and combustion controllability. RCCI is a dual-fuel partially premixed combustion concept. In this strategy, a low reactivity fuel, such as gasoline or an alcohol fuel, is premixed via port fuel injection (PFI) and a high reactivity fuel, such as diesel fuel, is direct injected (DI) during the compression stroke. Once it was clear that dual-fuel RCCI operation had great potential in terms of combustion controllability, which is a great challenge for LTC strategies, the study focused on alternative fuels with RCCI combustion. The light-duty engine was used to study two different fuel combinations: gasoline/diesel and methanol/diesel. In addition to the fuels comparison, a modified piston bowl geometry was studied and compared to the stock re-entrant bowl. The modified piston featured a wide/shallow bowl with a matched geometric compression ratio to the stock piston of ~17.3. Using the modified piston, the gross indicated efficiency of RCCI combustion was significantly improved at light loads due to increases in combustion efficiency and decreases in heat transfer losses. At higher loads the modified piston also performed better than the stock piston, but the improvements were not as significant. The final portion of this research looks at the effects of cetane improvers on gasoline, ethanol, and methanol's fuel reactivity and the implications for RCCI combustion. In all three base fuels it was found that 2-ethylhexyl nitrate is more effective at increasing fuel reactivity (i.e., suppressing the octane number) compared to di-tert-butyl peroxide. However, 2-ethylhexyl nitrate has a potential disadvantage due its nitrate group, which can manifest itself as NOx emissions in the exhaust. The relationship between the fuel-bound nitrate group and the engine-out NOx emissions was extensively characterized. It was also observed that methanol's response to cetane improvers was better than that of ethanol, in spite of the fact that they have similar reactivities in their neat form.
Download or read book Homogeneous Charge Compression Ignition HCCI Engines written by Fuquan Zhao and published by SAE International. This book was released on 2003-01-01 with total page 658 pages. Available in PDF, EPUB and Kindle. Book excerpt: The homogeneous charge, compression-ignition (HCCI) combustion process has the potential to significantly reduce NOx and particulate emissions, while achieving high thermal efficiency and the capability of operating with a wide variety of fuels. This makes the HCCI engine an attractive technology that can ostensibly provide diesel-like fuel efficiency and very low emissions, which may allow emissions compliance to occur without relying on lean aftertreatment systems. A profound increase in the level of research and development of this technology has occurred in the last decade. This book gathers contributions from experts in both industry and academia, providing a basic introduction to the state-of-the-art of HCCI technology, a critical review of current HCCI research and development efforts, and perspective for the future. Chapters cover: Gasoline-Fueled HCCI Engines; Diesel-Fueled HCCI Engines; Alternative Fuels and Fuel Additives for HCCI Engines; HCCI Control and Operating Range Extension; Kinetics of HCCI Combustion; HCCI Engine Modeling Approaches.In addition to the extensive overview of terminology, physical processes, and future needs, each chapter also features select SAE papers (a total of 41 are included in the book), as well as a comprehensive list of references related to the subjects. Homogeneous Charge Compression Ignition (HCCI) Engines: Key Research and Development Issues provides a valuable base of information for those interested in learning about this rapidly-progressing technology which has the potential to enhance fuel economy and reduce emissions.
Download or read book The Association of Automotive Fuel Composition with Exhaust Reactivity written by and published by . This book was released on 1973 with total page 60 pages. Available in PDF, EPUB and Kindle. Book excerpt:
