Download or read book Effectiveness of Tire road Noise Abatement Through Surface Retexturing by Diamond Grinding for Project SUM 76 15 40 written by Lloyd Allen Herman and published by . This book was released on 2005 with total page 112 pages. Available in PDF, EPUB and Kindle. Book excerpt: A portion of I-76, near Akron, OH, had been reconstructed by the Ohio Department of Transportation (ODOT) using concrete to replace the previous surface, which was constructed of asphalt. In the process of reconstruction, the concrete surface was textured with random transverse grooves to comply with the current ODOT specification. Subsequent to construction, residents living in the project area as far as 2600 ft (800 m) from the roadway, perceived an unfavorable difference in their noise environment, which they attributed to the new concrete pavement used on the reconstruction project. Therefore, a project was initiated to re-texture the pavement surface by diamond grinding. The transverse grooves were replaced with longitudinal grooves. Traffic noise measurements were made before and after grinding at five sites in the project area, at distances from 7.5 m to 120 m from the center of the near travel lane. The average reduction in broadband noise at 7.5 m was 3.5 dB, and the average reduction at15m was 3.1 dB. Spectrum analysis showed the greatest reduction in noise occurred at frequencies above 1 kHz and that the retexuring had little to no effect on frequencies less than 200 Hz.
Download or read book Effectiveness of Tire road Noise Abatement Through Surface Retexturing by Diamond Grinding written by Jared Withers and published by . This book was released on 2006 with total page 107 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Effectiveness of Tire road Noise Abatement Through Surface Retexturing by Diamond Grinding for Project SUM 76 15 40 written by Lloyd Allen Herman and published by . This book was released on 2005 with total page 112 pages. Available in PDF, EPUB and Kindle. Book excerpt: A portion of I-76, near Akron, OH, had been reconstructed by the Ohio Department of Transportation (ODOT) using concrete to replace the previous surface, which was constructed of asphalt. In the process of reconstruction, the concrete surface was textured with random transverse grooves to comply with the current ODOT specification. Subsequent to construction, residents living in the project area as far as 2600 ft (800 m) from the roadway, perceived an unfavorable difference in their noise environment, which they attributed to the new concrete pavement used on the reconstruction project. Therefore, a project was initiated to re-texture the pavement surface by diamond grinding. The transverse grooves were replaced with longitudinal grooves. Traffic noise measurements were made before and after grinding at five sites in the project area, at distances from 7.5 m to 120 m from the center of the near travel lane. The average reduction in broadband noise at 7.5 m was 3.5 dB, and the average reduction at15m was 3.1 dB. Spectrum analysis showed the greatest reduction in noise occurred at frequencies above 1 kHz and that the retexuring had little to no effect on frequencies less than 200 Hz.
Download or read book Cost benefit Analysis written by Cori Vanchieri and published by . This book was released on 2014 with total page 48 pages. Available in PDF, EPUB and Kindle. Book excerpt: "EXECUTIVE SUMMARY: At highway speeds, the major source of noise is the interaction between tires and the road surface. Noise barriers have been used by state transportation departments for many years and are the preferred solution for reducing highway traffic noise. Federal Highway Administration regulations for highway traffic and construction noise abatement are included in the Code of Federal Regulations (23 CFR772)1 and currently only consider noise barriers as an abatement measure for highway noise. However, pavement type can considerably reduce the noise generated from tire-road interaction. Yet considering pavement as a noise abatement measure is currently only allowed for pilot projects approved by the Federal Highway Administration. Through the end of 2010, 47 state departments of transportation and the Commonwealth of Puerto Rico have constructed more than 2,748 linear miles of barriers at a cost of close to 5 .5 billion (in 2010 dollars)2 . Treatment of highway pavement is generally less costly than the construction of barriers, but the noise reduction achieved by a quieter pavement is typically less than the reduction from a well-designed barrier, at least for residents in the immediate vicinity of the barrier. However, quieter pavements produce a reduction of noise at the source, which means that it may be possible to increase the number of benefited receptors (the recipient of an abatement measure that receives a noise reduction at or above the highway agency's chosen noise impact threshold value). A combination of barrier and pavement treatment may lead to cost-effective solutions to highway noise. To evaluate effectiveness of quieter pavements, a reliable measurement method for tire/road noise is needed. The method that is currently favored is measuring On-Board Sound Intensity (OBSI). OBSI data are collected in conformance with AASHTO TP-76,3 the American Association of State Highway and Transportation Officials Standard Method of Test for Measurement of Tire/Pavement Noise Using the On-Board Sound Intensity (OBSI) Method. A workshop on cost-benefit analysis of noise barriers and quieter pavements was held on January 16, 2014. One objective of the workshop was to evaluate the National Cooperative Highway Research Program Report 738, "Evaluating Pavement Strategies and Barriers for Noise Mitigation". Report 738 was prepared under Project 10-76, and is typically referred to as NCHRP 10-76.4 The report describes a methodology for the evaluation of both barriers and pavements for noise abatement, and explores how quieter pavement technology can be incorporated into Federal and state noise policy. Three key elements of the method presented in NCHRP 10-76 involve life cycle cost analysis (LCCA), the use of a research version5 of the Federal Highway Administration Traffic Noise Model (TNM), and a method for the evaluation of tire pavement noise reduction, OBSI. This report contains summaries of the presentations given during the workshop and the results of discussions identifying the challenges presented by implementing the NCHRP 10-76 methodology, especially to state departments of transportation, which carry out noise abatement projects in cooperation with the Federal Highway Administration and in conformance with the federal requirements in 23 CFR772. Using LCCA, planners can evaluate the initial cost of abatement using pavement and barriers as well as rehabilitation and maintenance costs. The methodology also incorporates a measure of the effectiveness of the resulting predicted level of traffic noise. Current regulations require impact determination and barrier design to be completed with the public-release version of TNM and average pavement. By using a research version of TNM and OBSI data to refine the tire-pavement interaction noise source, pavement effects could be included in the model (and therefore predictions could be more accurate and pavement type can be considered when assessing noise impact and abatement). Several examples illustrated that the NCHRP 10-76 approach can be successfully applied to real highway project studies. In some situations, a barrier-and-pavement hybrid solution can be more acoustically effective and/or cost effective than a barrier only solution and can allow for additional benefited receptors where a barrier only solution would not be feasible and/or reasonable. Both current regulations and the public- release version of TNM require modification if the noise reduction benefits of pavements are to be realized in construction projects. The noise reduction achieved by sound propagation over sound-absorptive pavement could also be included in the public-release version of TNM. An important part of the workshop, which was attended by noise barrier and pavement experts, as well as representatives from the FHWA and state departments of transportation, was to discuss the challenges of implementing NCHRP 10-76 methodology to state departments of transportation and to develop findings and recommendations based on these discussions. The key elements of these discussions are presented in Chapter 3 of this report. The following recommendations appear in Chapter 4 of this report: Develop and document a noise evaluation process that accounts for both noise barriers and quieter pavements. Provide funding and implement the method presented to evaluate the abatement options on a pilot program basis to help evaluate and improve the process. Upgrade the public release version of TNM to include the OBSI-related pavement assessment capabilities currently available in the research version of TNM. Organize and make publically available national databases for OBSI and LCCA. Expand TNM and highway noise abatement training to include consideration of quieter pavements and enable use of the research version of TNM. Encourage FHWA to develop guidance on the use of quieter pavements and barriers for noise abatement. Incorporate noise performance into a new performance management system. Develop and provide a noise abatement training program for pavement engineering staff. Other presentations from the workshop with important background information relevant to cost benefit analysis, noise barriers, and quieter pavements are summarized in Appendix A. The workshop agenda, the names of the participants, definitions of terms and a list of acronyms are provided in Appendix B, Appendix C, and Appendix D."
Download or read book Survey of Traffic Noise Reduction Products Materials and Technologies written by Brown, Vi (Violettee) and published by . This book was released on 2008 with total page 90 pages. Available in PDF, EPUB and Kindle. Book excerpt: Noise is one of the most pervasive forms of environmental pollution. It is everywhere and affects our lives at home, work and play. By definition, noise is any unwanted or excessive sound. Highway traffic noise is a major issue for transportation agencies. The objective of this study was to identify noise reduction products, materials, and technologies currently available and that may have potential as noise mitigation alternatives. The literature review and survey identified measures that are being used by U.S. transportation organizations as well as international efforts. Some key findings from the literature review show the following best practices: - Pavement Noise Reduction Products - noise or sound walls dominate this category and have been used for decades in the U.S. Findings from the literature revealed a variety of materials to choose from that are both aesthetically attractive, and effective in reducing sound from tire pavement noise. The cost of installing products will need to be evaluated on a case by case basis with the vendor or for each applicable product. - Pavement Noise Reduction Materials - The operating speed of the roadway should be factored into the roadway design for quiet pavements. European studies show that higher porous mixtures tend to clog under slower speeds. Two layer-porous mixes have been found to be effective in Europe and the US. An important attribute for consideration in two layer-porous mix design and placement is aggregate size. - Pavement Noise Reduction Technologies - use of thin-textured surfacings with a negative pavement depression are recommended for urban or low-speed roadway sections. Diamond grinding enhances noise reduction on concrete surfaces in sensitive locations. - Other Pavement Noise Reduction Measures - looking forward, transportation officials are encouraged to develop an integrated approach to roadway noise reduction. Instead of relying on a single measure, the recommended forward strategy is to develop the ability to model the effectiveness of a number of different measures to achieve greater noise reduction.
Download or read book How to Reduce Tire pavement Noise written by and published by . This book was released on 2008 with total page 62 pages. Available in PDF, EPUB and Kindle. Book excerpt: Better practices to improve surface properties and thus tire-pavement noise are really about establishing a higher order of control over the texture and other surface properties. It is not about designing or building "innovative" surfaces, but rather the control of conventional texturing techniques. There should be a renewed awareness of the impact that some of the subtle operational characteristics can have on the texture as constructed. Predictable tire-pavement noise levels are not about how the texture is imparted as much as they are about the recognition and management of the sources of variability. Regarding the concrete, noise levels have to do with the fact that the contractors are imparting texture into a material with inherent variability in both stiffness and plasticity. Concrete changes from batch-to-batch, and it changes within a batch. The wind and the sun play a major role, as does the timing of the concrete mixing, transport, placement, and (eventually) the texturing and curing (the latter being important for acoustical durability).
Download or read book A Review of Current Research on Road Surface Noise Reduction Techniques written by P. G. Abbott and published by . This book was released on 2010 with total page 133 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Technology for a Quieter America written by National Academy of Engineering and published by National Academies Press. This book was released on 2010-10-30 with total page 210 pages. Available in PDF, EPUB and Kindle. Book excerpt: Exposure to noise at home, at work, while traveling, and during leisure activities is a fact of life for all Americans. At times noise can be loud enough to damage hearing, and at lower levels it can disrupt normal living, affect sleep patterns, affect our ability to concentrate at work, interfere with outdoor recreational activities, and, in some cases, interfere with communications and even cause accidents. Clearly, exposure to excessive noise can affect our quality of life. As the population of the United States and, indeed, the world increases and developing countries become more industrialized, problems of noise are likely to become more pervasive and lower the quality of life for everyone. Efforts to manage noise exposures, to design quieter buildings, products, equipment, and transportation vehicles, and to provide a regulatory environment that facilitates adequate, cost-effective, sustainable noise controls require our immediate attention. Technology for a Quieter America looks at the most commonly identified sources of noise, how they are characterized, and efforts that have been made to reduce noise emissions and experiences. The book also reviews the standards and regulations that govern noise levels and the federal, state, and local agencies that regulate noise for the benefit, safety, and wellness of society at large. In addition, it presents the cost-benefit trade-offs between efforts to mitigate noise and the improvements they achieve, information sources available to the public on the dimensions of noise problems and their mitigation, and the need to educate professionals who can deal with these issues. Noise emissions are an issue in industry, in communities, in buildings, and during leisure activities. As such, Technology for a Quieter America will appeal to a wide range of stakeholders: the engineering community; the public; government at the federal, state, and local levels; private industry; labor unions; and nonprofit organizations. Implementation of the recommendations in Technology for a Quieter America will result in reduction of the noise levels to which Americans are exposed and will improve the ability of American industry to compete in world markets paying increasing attention to the noise emissions of products.
Download or read book Guide for Pavement Friction written by and published by AASHTO. This book was released on 2008 with total page 87 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report contains guidelines and recommendations for managing and designing for friction on highway pavements. The contents of this report will be of interest to highway materials, construction, pavement management, safety, design, and research engineers, as well as others concerned with the friction and related surface characteristics of highway pavements.
Download or read book Tyre Road Noise written by Ulf Sandberg and published by . This book was released on 2002 with total page 616 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Microsurfacing written by Douglas D. Gransberg and published by Transportation Research Board. This book was released on 2010 with total page 124 pages. Available in PDF, EPUB and Kindle. Book excerpt: TRB's National Cooperative Highway Research Program (NCHRP) Synthesis 411: Microsurfacing explores highway microsurfacing project selection, design, contracting, equipment, construction, and performance measurement processes used by transportation agencies in the United States and Canada. Microsurfacing is a polymer-modified cold-mix surface treatment that has the potential to address a broad range of problems on today's highways --
Download or read book Integrated Materials and Construction Practices for Concrete Pavement written by and published by . This book was released on 2006 with total page 326 pages. Available in PDF, EPUB and Kindle. Book excerpt: Manual of integrated material and construction practices for concrete pavements.
Download or read book Precast Concrete Pavement Technology written by Shiraz D. Tayabji and published by . This book was released on 2013 with total page 184 pages. Available in PDF, EPUB and Kindle. Book excerpt: "TRB's second Strategic Highway Research Program (SHRP 2) Report S2-R05-RR-1: Precast Concrete Pavement Technology reviews the available precast concrete pavement (PCP) systems; summarizes PCP applications; and offers suggested guidelines for the design, fabrication, installation, and selection of PCP systems. " -- Publisher's description.
Download or read book Mechanistic empirical Pavement Design Guide written by American Association of State Highway and Transportation Officials and published by AASHTO. This book was released on 2008 with total page 218 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Proceedings of the 5th International Conference on Industrial Engineering ICIE 2019 written by Andrey A. Radionov and published by Springer Nature. This book was released on 2019-11-14 with total page 1449 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book highlights recent findings in industrial, manufacturing and mechanical engineering, and provides an overview of the state of the art in these fields, mainly in Russia and Eastern Europe. A broad range of topics and issues in modern engineering are discussed, including the dynamics of machines and working processes, friction, wear and lubrication in machines, surface transport and technological machines, manufacturing engineering of industrial facilities, materials engineering, metallurgy, control systems and their industrial applications, industrial mechatronics, automation and robotics. The book gathers selected papers presented at the 5th International Conference on Industrial Engineering (ICIE), held in Sochi, Russia in March 2019. The authors are experts in various fields of engineering, and all papers have been carefully reviewed. Given its scope, the book will be of interest to a wide readership, including mechanical and production engineers, lecturers in engineering disciplines, and engineering graduates.
Download or read book Advances in Manufacturing and Industrial Engineering written by Ranganath M. Singari and published by Springer Nature. This book was released on 2021-01-13 with total page 1180 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents selected peer reviewed papers from the International Conference on Advanced Production and Industrial Engineering (ICAPIE 2019). It covers a wide range of topics and latest research in mechanical systems engineering, materials engineering, micro-machining, renewable energy, industrial and production engineering, and additive manufacturing. Given the range of topics discussed, this book will be useful for students and researchers primarily working in mechanical and industrial engineering, and energy technologies.
Download or read book Twentieth Century Building Materials written by Thomas C. Jester and published by Getty Publications. This book was released on 2014-08-01 with total page 354 pages. Available in PDF, EPUB and Kindle. Book excerpt: Over the concluding decades of the twentieth century, the historic preservation community increasingly turned its attention to modern buildings, including bungalows from the 1930s, gas stations and diners from the 1940s, and office buildings and architectural homes from the 1950s. Conservation efforts, however, were often hampered by a lack of technical information about the products used in these structures, and to fill this gap Twentieth-Century Building Materials was developed by the U.S. Department of the Interior’s National Park Service and first published in 1995. Now, this invaluable guide is being reissued—with a new preface by the book’s original editor. With more than 250 illustrations, including a full-color photographic essay, the volume remains an indispensable reference on the history and conservation of modern building materials. Thirty-seven essays written by leading experts offer insights into the history, manufacturing processes, and uses of a wide range of materials, including glass block, aluminum, plywood, linoleum, and gypsum board. Readers will also learn about how these materials perform over time and discover valuable conservation and repair techniques. Bibliographies and sources for further research complete the volume. The book is intended for a wide range of conservation professionals including architects, engineers, conservators, and material scientists engaged in the conservation of modern buildings, as well as scholars in related disciplines.
