Download or read book Effect of Temperature and Strain Rate on Low Cycle Fatigue Resistance of AISI 304 316 and 348 Stainless Steels written by JT. Berling and published by . This book was released on 1969 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt: Results are reported of strain-controlled, low-cycle fatigue experiments conducted on annealed AISI 304, 316, and 348 stainless steels at temperatures of 430, 650, and 816 C with strain rates of approximately 4 x 10-3, 4 x 10-4, and 4 x 10-5 s-1. The investigation generally shows that fatigue life measured in terms of sustained loading cycles is affected adversely by the increase in temperature and by the decrease in strain rate. The test results were generated with servo-controlled, hydraulic testing machines using inductively heated hourglass-type specimens. Cyclic stress-strain data are compared with monotonic stress-strain data obtained from tension tests performed at the same temperatures and strain rates.
Download or read book Effect of Temperature and Strain Rate on Low cycle Fatigue Resistance of Aisi 304 316 and 348 Stainless Steels written by J. T. BERLING and published by . This book was released on 1974 with total page 49 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book hold time effects in high temperature low cycle fatigue written by and published by ASTM International. This book was released on 1971 with total page 37 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fatigue at High Temperature written by American Society for Testing and Materials and published by ASTM International. This book was released on 1969 with total page 161 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fatigue at High Temperature written by and published by ASTM International. This book was released on 1969 with total page 166 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Effect of Notches on Low cycle Fatigue written by B. M. Wundt and published by ASTM International. This book was released on 1972 with total page 73 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Manual on Low Cycle Fatigue Testing written by American Society for Testing Materials and published by ASTM International. This book was released on 1969 with total page 208 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Low cycle Fatigue of Type 347 Stainless Steel and Hastelloy Alloy X in Hydrogen Gas and in Air at Elevated Temperatures written by and published by . This book was released on 1976 with total page 116 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Advances in Fatigue Science and Technology written by C. Moura Branco and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 982 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume contains the edited version of lectures and selected research contributions presented at the NATO ADVANCED STUDY INSTITUTE on ADVANCES IN FATIGUE SCIENCE AND TECHNOLOGY. held in Alvor. Portugal, 4th to 15th of April 1988. and organized by CEMUL - Center of Mechanics and Materials of The Technical University of Lisbon. The Institute was attended by 101 participants, including 15 lecturers. from 14 countries. The participants were leading scientists and engineers from universities, research institutions and industry. and also Ph.D~ students. Some participants presented papers during the Institute reporting the state-of-art of their research projects. All the sessions wel'e very active and quite extensive discussions on scientific aspects took place during the Institute. The Advanced Study Institute provided a forum for interaction among eminent scientists and engineers. from different schools of thought and young researchers. The Institute addressed the foundations and current state of the art of essential aspects related to fatigue science and technology, namely: Short Cracks, Metallurgical Aspects, Environmental Fatigue, Threshold Behaviour, Notch Behaviour. Creep and Fatigue Interactions at High Temperature, Multiaxial Fatigue, Low Cycle Fatigue, Methodology of Fatigue Testing, Variable Amplitude Fatigue, Fatigue of Advanced Materials. Elastic-Plastic Fatigue, and several engineering applications such as welded joints, energy systems, offshore structures, automotive industry, machine and engine components. This book is organized in three parts: Part I: Fundamentals of Fatigue Part II: Engineering Applications Part III: Research Contributions The research contributions covered most of the areas referred above.
Download or read book Technical Papers of the 23rd Metallographic Group Meeting written by and published by . This book was released on 1969 with total page 252 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Cyclic Stress strain Behavior analysis Experimentation and Failure Prediction written by and published by ASTM International. This book was released on 1971 with total page 293 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fatigue Mechanisms written by Jeffrey T. Fong and published by ASTM International. This book was released on 1979 with total page 936 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book High Temperature Fatigue written by R.P. Skelton and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 330 pages. Available in PDF, EPUB and Kindle. Book excerpt: About 35 years ago, thermal fatigue was identified as an important phenomenon which limited the lifetime of high temperature plant. In the intervening years many investigations have been carried out, primarily to give guidance on likely endurance (especially in the presence of time dependent deformation) but latterly, with the introduction of sophisticated testing machines, to provide knowledge of the underlying mechanisms of failure. A previous edited book (Fatigue at High Temperature, Elsevier Applied Science Publishers, 1983) summarised the state-of-the-art of high temperature fatigue testing and examined the factors influencing life, such as stress state, environment and microstructural effects. It also considered, in some detail, cyclic crack growth as a more rigorous approach to life limitation. The aim of the present volume (which in style and format follows exactly the same lines as its predecessor) is once again to pursue the desire to translate detailed laboratory knowledge into engineering design and assessment. There is, for example, a need to consider the limitations of the laboratory specimen and its relationship with engineering features. Many design procedures still rely on a simple endurance approach based on failure of a smooth specimen, and this is taken to indicate crack initiation in the component. In this volume, therefore, crack propagation is covered only incidentally, emphasis being placed instead on basic cyclic stress strain properties, non-isothermal behaviour, metallography, failure criteria and the need for agreed testing procedures.
Download or read book Nuclear Science Abstracts written by and published by . This book was released on 1970 with total page 1202 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Metal Fatigue in Engineering written by Ralph I. Stephens and published by John Wiley & Sons. This book was released on 2000-11-03 with total page 496 pages. Available in PDF, EPUB and Kindle. Book excerpt: Classic, comprehensive, and up-to-date Metal Fatigue in Engineering Second Edition For twenty years, Metal Fatigue in Engineering has served as an important textbook and reference for students and practicing engineers concerned with the design, development, and failure analysis of components, structures, and vehicles subjected to repeated loading. Now this generously revised and expanded edition retains the best features of the original while bringing it up to date with the latest developments in the field. As with the First Edition, this book focuses on applied engineering design, with a view to producing products that are safe, reliable, and economical. It offers in-depth coverage of today's most common analytical methods of fatigue design and fatigue life predictions/estimations for metals. Contents are arranged logically, moving from simple to more complex fatigue loading and conditions. Throughout the book, there is a full range of helpful learning aids, including worked examples and hundreds of problems, references, and figures as well as chapter summaries and "design do's and don'ts" sections to help speed and reinforce understanding of the material. The Second Edition contains a vast amount of new information, including: * Enhanced coverage of micro/macro fatigue mechanisms, notch strain analysis, fatigue crack growth at notches, residual stresses, digital prototyping, and fatigue design of weldments * Nonproportional loading and critical plane approaches for multiaxial fatigue * A new chapter on statistical aspects of fatigue
Download or read book NASA Contractor Report written by and published by . This book was released on 1982 with total page 692 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Proceedings of the US USSR Seminar on Problems of Reliable and Safe Operation of LMFBR Steam Generators written by and published by . This book was released on 1976 with total page 668 pages. Available in PDF, EPUB and Kindle. Book excerpt:
