Download or read book Effect of High Free Stream Turbulence on Film Cooling Using Double Row of 30 Deg Slant Hole Injectors written by Lilith I. Sorensen and published by . This book was released on 1998-03-01 with total page 208 pages. Available in PDF, EPUB and Kindle. Book excerpt: In this study free stream turbulence levels from 7.3% to 17.8% are applied to film cooling over a flat plate with two rows of 30 deg slant holes using a wall jet as the main stream air supply and source of turbulence. Blowing ratios are varied from 0.25 to 2.0 and free stream velocities at injection range from 10 m/s to 85 m/s. A constant density ratio of 1.07 is kept throughout the experiment. Results show that for different magnitudes of blowing ratio free stream turbulence has a different influence on effectiveness. At the forward stations, where blow off was present at high blowing ratios, high free stream turbulence increased effectiveness. While at mid to aft stations for all blowing ratios high free stream turbulence decreased effectiveness. A correlation for effectiveness with a non-dimensional group of film cooling parameters is offered. The effectiveness correlated best 10 to 15 diameters after injection where blow off effects are no longer present, and before the very far downstream stations where uncertainties in the measurements were greater.
Download or read book Masters Theses in the Pure and Applied Sciences written by Wade H. Shafer and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 411 pages. Available in PDF, EPUB and Kindle. Book excerpt: Masters Theses in the Pure and Applied Sciences was first conceived, published, and disseminated by the Center for Information and Numerical Data Analysis and Synthesis (CINDAS) * at Purdue University in 1 957, starting its coverage of theses with the academic year 1955. Beginning with Volume 13, the printing and dissemination phases of the activity were transferred to University Microfilms/Xerox of Ann Arbor, Michigan, with the thought that such an arrangement would be more beneficial to the academic and general scientific and technical community. After five years of this joint undertaking we had concluded that it was in the interest of all con cerned if the printing and distribution of the volumes were handled by an interna tional publishing house to assure improved service and broader dissemination. Hence, starting with Volume 18, Masters Theses in the Pure and Applied Sciences has been disseminated on a worldwide basis by Plenum Publishing Cor poration of New York, and in the same year the coverage was broadened to include Canadian universities. All back issues can also be ordered from Plenum. We have reported in Volume 32 (thesis year 1987) a total of 12,483 theses titles from 22 Canadian and 176 United States universities. We are sure that this broader base for these titles reported will greatly enhance the value of this important annual reference work. While Volume 32 reports theses submitted in 1987, on occasion, certain univer sities do report theses submitted in previous years but not reported at the time.
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1987 with total page 1124 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Air University Abstracts of Research Reports written by and published by . This book was released on 1986 with total page 932 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book International Aerospace Abstracts written by and published by . This book was released on 1990 with total page 1068 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Effects of Hole Length Supply Plenum Geometry and Freestream Turbulence on Film Cooling Performance written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-06-27 with total page 322 pages. Available in PDF, EPUB and Kindle. Book excerpt: Experimental measurements are presented in this report to document the sensitivity of film cooling performance to the hole length and coolant delivery plenum geometry. Measurements with hot-wire anemometry detail velocity, local turbulence, and spectral distributions over the exit plane of film cooling holes and downstream of injection in the coolant-freestream interaction zone. Measurements of discharge coefficients and adiabatic effectiveness are also provided. Coolant is supplied to the film cooling holes by means of a large, open plenum and through plenums which force the coolant to approach the holes either co-current or counter-current to the freestream. A single row of film cooling holes with 35 degree-inclined streamwise at two coolant-to-freestream velocity ratios, 0.5 and 1.0, is investigated. The coolant-to-freestream density ratio is maintained in the range 0.96 to 1.0. Measurements were taken under high-freestream (FSTI = 12%) and low-freestream turbulence intensity (FSTI = 0.5%) conditions. The results document the effects of the hole L/D, coolant supply plenum geometry, velocity ratio, and FSTI. In general, hole L/D and the supply plenum geometry play influential roles in the film cooling performance. Hole L/D effects, however, are more pronounced. Film cooling performance is also dependent upon the velocity ratio and FSTI. Burd, Steven W. and Simon, Terrence W. and Thurman, Douglas (Technical Monitor) Glenn Research Center NAG3-1638; RTOP 714-01-4A...
Download or read book Fuel Systems for IC Engines written by Institution of Mechanical Engineers and published by Elsevier. This book was released on 2012-03-06 with total page 348 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the papers from the latest conference in this successful series on fuel injection systems for internal combustion engines. It is vital for the automotive industry to continue to meet the demands of the modern environmental agenda. In order to excel, manufacturers must research and develop fuel systems that guarantee the best engine performance, ensuring minimal emissions and maximum profit. The papers from this unique conference focus on the latest technology for state-of-the-art system design, characterisation, measurement, and modelling, addressing all technological aspects of diesel and gasoline fuel injection systems. Topics range from fundamental fuel spray theory, component design, to effects on engine performance, fuel economy and emissions. - Presents the papers from the IMechE conference on fuel injection systems for internal combustion engines - Papers focus on the latest technology for state-of-the-art system design, characterisation, measurement and modelling; addressing all technological aspects of diesel and gasoline fuel injection systems - Topics range from fundamental fuel spray theory and component design to effects on engine performance, fuel economy and emissions
Download or read book Airframe and Powerplant Mechanics Airframe Handbook written by United States. Flight Standards Service and published by . This book was released on 1976 with total page 620 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Extrusion written by Harold F. Giles Jr and published by William Andrew. This book was released on 2013-09-21 with total page 638 pages. Available in PDF, EPUB and Kindle. Book excerpt: The second edition of Extrusion is designed to aid operators, engineers, and managers in extrusion processing in quickly answering practical day-to-day questions. The first part of the book provides the fundamental principles, for operators and engineers, of polymeric materials extrusion processing in single and twin screw extruders. The next section covers advanced topics including troubleshooting, auxiliary equipment, and coextrusion for operators, engineers, and managers. The final part provides applications case studies in key areas for engineers such as compounding, blown film, extrusion blow molding, coating, foam, and reprocessing. This practical guide to extrusion brings together both equipment and materials processing aspects. It covers basic and advanced topics, for reference and training, in thermoplastics processing in the extruder. Detailed reference data are provided on such important operating conditions as temperatures, start-up procedures, shear rates, pressure drops, and safety. - A practical guide to the selection, design and optimization of extrusion processes and equipment - Designed to improve production efficiency and product quality - Focuses on practical fault analysis and troubleshooting techniques
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1991 with total page 296 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Gas Turbine Engineering Handbook written by Meherwan P. Boyce and published by Elsevier. This book was released on 2017-09-01 with total page 956 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Gas Turbine Engineering Handbook has been the standard for engineers involved in the design, selection, and operation of gas turbines. This revision includes new case histories, the latest techniques, and new designs to comply with recently passed legislation. By keeping the book up to date with new, emerging topics, Boyce ensures that this book will remain the standard and most widely used book in this field. The new Third Edition of the Gas Turbine Engineering Hand Book updates the book to cover the new generation of Advanced gas Turbines. It examines the benefit and some of the major problems that have been encountered by these new turbines. The book keeps abreast of the environmental changes and the industries answer to these new regulations. A new chapter on case histories has been added to enable the engineer in the field to keep abreast of problems that are being encountered and the solutions that have resulted in solving them. - Comprehensive treatment of Gas Turbines from Design to Operation and Maintenance. In depth treatment of Compressors with emphasis on surge, rotating stall, and choke; Combustors with emphasis on Dry Low NOx Combustors; and Turbines with emphasis on Metallurgy and new cooling schemes. An excellent introductory book for the student and field engineers - A special maintenance section dealing with the advanced gas turbines, and special diagnostic charts have been provided that will enable the reader to troubleshoot problems he encounters in the field - The third edition consists of many Case Histories of Gas Turbine problems. This should enable the field engineer to avoid some of these same generic problems
Download or read book Rules of Thumb for Chemical Engineers written by Carl Branan and published by Gulf Professional Publishing. This book was released on 2002 with total page 438 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fractionators, separators and accumulators, cooling towers, gas treating, blending, troubleshooting field cases, gas solubility, and density of irregular solids * Hundreds of common sense techniques, shortcuts, and calculations.
Download or read book Unsteady Computational Fluid Dynamics in Aeronautics written by P.G. Tucker and published by Springer Science & Business Media. This book was released on 2013-08-30 with total page 432 pages. Available in PDF, EPUB and Kindle. Book excerpt: The field of Large Eddy Simulation (LES) and hybrids is a vibrant research area. This book runs through all the potential unsteady modelling fidelity ranges, from low-order to LES. The latter is probably the highest fidelity for practical aerospace systems modelling. Cutting edge new frontiers are defined. One example of a pressing environmental concern is noise. For the accurate prediction of this, unsteady modelling is needed. Hence computational aeroacoustics is explored. It is also emerging that there is a critical need for coupled simulations. Hence, this area is also considered and the tensions of utilizing such simulations with the already expensive LES. This work has relevance to the general field of CFD and LES and to a wide variety of non-aerospace aerodynamic systems (e.g. cars, submarines, ships, electronics, buildings). Topics treated include unsteady flow techniques; LES and hybrids; general numerical methods; computational aeroacoustics; computational aeroelasticity; coupled simulations and turbulence and its modelling (LES, RANS, transition, VLES, URANS). The volume concludes by pointing forward to future horizons and in particular the industrial use of LES. The writing style is accessible and useful to both academics and industrial practitioners. From the reviews: "Tucker's volume provides a very welcome, concise discussion of current capabilities for simulating and modellng unsteady aerodynamic flows. It covers the various pos sible numerical techniques in good, clear detail and presents a very wide range of practical applications; beautifully illustrated in many cases. This book thus provides a valuable text for practicing engineers, a rich source of background information for students and those new to this area of Research & Development, and an excellent state-of-the-art review for others. A great achievement." Mark Savill FHEA, FRAeS, C.Eng, Professor of Computational Aerodynamics Design & Head of Power & Propulsion Sciences, Department of Power & Propulsion, School of Engineering, Cranfield University, Bedfordshire, U.K. "This is a very useful book with a wide coverage of many aspects in unsteady aerodynamics method development and applications for internal and external flows." L. He, Rolls-Royce/RAEng Chair of Computational Aerothermal Engineering, Oxford University, U.K. "This comprehensive book ranges from classical concepts in both numerical methods and turbulence modelling approaches for the beginner to latest state-of-the-art for the advanced practitioner and constitutes an extremely valuable contribution to the specific Computational Fluid Dynamics literature in Aeronautics. Student and expert alike will benefit greatly by reading it from cover to cover." Sébastien Deck, Onera, Meudon, France
Download or read book Low Speed Wind Tunnel Testing written by Jewel B. Barlow and published by John Wiley & Sons. This book was released on 1999-02-22 with total page 738 pages. Available in PDF, EPUB and Kindle. Book excerpt: A brand-new edition of the classic guide on low-speed wind tunnel testing While great advances in theoretical and computational methods have been made in recent years, low-speed wind tunnel testing remains essential for obtaining the full range of data needed to guide detailed design decisions for many practical engineering problems. This long-awaited Third Edition of William H. Rae, Jr.'s landmark reference brings together essential information on all aspects of low-speed wind tunnel design, analysis, testing, and instrumentation in one easy-to-use resource. Written by authors who are among the most respected wind tunnel engineers in the world, this edition has been updated to address current topics and applications, and includes coverage of digital electronics, new instrumentation, video and photographic methods, pressure-sensitive paint, and liquid crystal-based measurement methods. The book is organized for quick access to topics of interest, and examines basic test techniques and objectives of modeling and testing aircraft designs in low-speed wind tunnels, as well as applications to fluid motion analysis, automobiles, marine vessels, buildings, bridges, and other structures subject to wind loading. Supplemented with real-world examples throughout, Low-Speed Wind Tunnel Testing, Third Edition is an indispensable resource for aerospace engineering students and professionals, engineers and researchers in the automotive industries, wind tunnel designers, architects, and others who need to get the most from low-speed wind tunnel technology and experiments in their work.
Download or read book Blindsight written by Peter Watts and published by Macmillan. This book was released on 2006-10-03 with total page 388 pages. Available in PDF, EPUB and Kindle. Book excerpt: Hugo and Shirley Jackson award-winning Peter Watts stands on the cutting edge of hard SF with his acclaimed novel, Blindsight Two months since the stars fell... Two months of silence, while a world held its breath. Now some half-derelict space probe, sparking fitfully past Neptune's orbit, hears a whisper from the edge of the solar system: a faint signal sweeping the cosmos like a lighthouse beam. Whatever's out there isn't talking to us. It's talking to some distant star, perhaps. Or perhaps to something closer, something en route. So who do you send to force introductions with unknown and unknowable alien intellect that doesn't wish to be met? You send a linguist with multiple personalities, her brain surgically partitioned into separate, sentient processing cores. You send a biologist so radically interfaced with machinery that he sees x-rays and tastes ultrasound. You send a pacifist warrior in the faint hope she won't be needed. You send a monster to command them all, an extinct hominid predator once called vampire, recalled from the grave with the voodoo of recombinant genetics and the blood of sociopaths. And you send a synthesist—an informational topologist with half his mind gone—as an interface between here and there. Pray they can be trusted with the fate of a world. They may be more alien than the thing they've been sent to find. At the Publisher's request, this title is being sold without Digital Rights Management Software (DRM) applied.
Download or read book Advanced Direct Injection Combustion Engine Technologies and Development written by H Zhao and published by Elsevier. This book was released on 2014-01-23 with total page 325 pages. Available in PDF, EPUB and Kindle. Book excerpt: Direct injection enables precise control of the fuel/air mixture so that engines can be tuned for improved power and fuel economy, but ongoing research challenges remain in improving the technology for commercial applications. As fuel prices escalate DI engines are expected to gain in popularity for automotive applications. This important book, in two volumes, reviews the science and technology of different types of DI combustion engines and their fuels. Volume 1 deals with direct injection gasoline and CNG engines, including history and essential principles, approaches to improved fuel economy, design, optimisation, optical techniques and their applications. - Reviews key technologies for enhancing direct injection (DI) gasoline engines - Examines approaches to improved fuel economy and lower emissions - Discusses DI compressed natural gas (CNG) engines and biofuels
Download or read book Gas Turbine Combustion written by Arthur H. Lefebvre and published by CRC Press. This book was released on 2010-04-26 with total page 560 pages. Available in PDF, EPUB and Kindle. Book excerpt: Reflecting the developments in gas turbine combustion technology that have occurred in the last decade, Gas Turbine Combustion: Alternative Fuels and Emissions, Third Edition provides an up-to-date design manual and research reference on the design, manufacture, and operation of gas turbine combustors in applications ranging from aeronautical to po
