Download or read book Effect of Hail Impact on Thermally Tempered Glass Substrates Used for Processing CdTe PV Modules written by Tushar M. Shimpi and published by . This book was released on 2008 with total page 6 pages. Available in PDF, EPUB and Kindle. Book excerpt: The IEEE 1262 standard provides qualification tests and specification to evaluate photovoltaic (PV) modules intended for power generation applications. The hail impact test is one of the tests. It is conducted to verify that the module will withstand a simulated hail impact without damage. The modules are tested with 1-in. diameter ice balls traveling at a velocity of 52 miles/h. Based on the results, the use of 3-mm tempered glass substrate for processing is recommended to withstand the hail impact test. The stresses developed by the samples during the hail impact test have been estimated.
Download or read book 70th Conference on Glass Problems written by Charles H. Drummond, III and published by John Wiley & Sons. This book was released on 2010-07-02 with total page 232 pages. Available in PDF, EPUB and Kindle. Book excerpt: This issue contains a collection of papers presented at the 70th Conference on Glass Problems at The Ohio State University, Columbus, Ohio. Topics include melting and molding, refractories, and environmental issues and new products.
Download or read book Solar Cells and Modules written by Arvind Shah and published by Springer Nature. This book was released on 2020-07-16 with total page 357 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book gives a comprehensive introduction to the field of photovoltaic (PV) solar cells and modules. In thirteen chapters, it addresses a wide range of topics including the spectrum of light received by PV devices, the basic functioning of a solar cell, and the physical factors limiting the efficiency of solar cells. It places particular emphasis on crystalline silicon solar cells and modules, which constitute today more than 90 % of all modules sold worldwide. Describing in great detail both the manufacturing process and resulting module performance, the book also touches on the newest developments in this sector, such as Tunnel Oxide Passivated Contact (TOPCON) and heterojunction modules, while dedicating a major chapter to general questions of module design and fabrication. Overall, it presents the essential theoretical and practical concepts of PV solar cells and modules in an easy-to-understand manner and discusses current challenges facing the global research and development community.
Download or read book Handbook of Photovoltaic Science and Engineering written by Antonio Luque and published by John Wiley & Sons. This book was released on 2011-01-31 with total page 1172 pages. Available in PDF, EPUB and Kindle. Book excerpt: The most comprehensive, authoritative and widely cited reference on photovoltaic solar energy Fully revised and updated, the Handbook of Photovoltaic Science and Engineering, Second Edition incorporates the substantial technological advances and research developments in photovoltaics since its previous release. All topics relating to the photovoltaic (PV) industry are discussed with contributions by distinguished international experts in the field. Significant new coverage includes: three completely new chapters and six chapters with new authors device structures, processing, and manufacturing options for the three major thin film PV technologies high performance approaches for multijunction, concentrator, and space applications new types of organic polymer and dye-sensitized solar cells economic analysis of various policy options to stimulate PV growth including effect of public and private investment Detailed treatment covers: scientific basis of the photovoltaic effect and solar cell operation the production of solar silicon and of silicon-based solar cells and modules how choice of semiconductor materials and their production influence costs and performance making measurements on solar cells and modules and how to relate results under standardised test conditions to real outdoor performance photovoltaic system installation and operation of components such as inverters and batteries. architectural applications of building-integrated PV Each chapter is structured to be partially accessible to beginners while providing detailed information of the physics and technology for experts. Encompassing a review of past work and the fundamentals in solar electric science, this is a leading reference and invaluable resource for all practitioners, consultants, researchers and students in the PV industry.
Download or read book Fundamentals of Photovoltaic Modules and Their Applications written by G. N. Tiwari and published by Royal Society of Chemistry. This book was released on 2010 with total page 423 pages. Available in PDF, EPUB and Kindle. Book excerpt: Presently there is no single publication available which covers the topics related to photovoltaic (PV) or photovoltaic thermal (PV/T) technologies, thermal modelling, CO2 mitigation and carbon trading. This book disseminates the current knowledge in the fundamentals of solar energy, photovoltaic (PV) or photovoltaic thermal (PV/T) technologies, energy security and climate change and is aimed at undergraduate and postgraduate students and professionals. The main emphasis of the book is on the design, construction, performance and application of PV and PV/T from the electricity and thermal standpoint. Hot topics covered in the book include: energy security of a nation, climate change, CO2 mitigation and carbon credit earned by using PV or PV/T technologies (Carbon Trading). This information will prove helpful in filling the gap between the researchers and professionals working on the application of photovoltaic and global climate change. It also covers economic, cost effective and sustainable aspects of photovoltaic technologies. The book gives a detailed history of the new technological developments in PV/T systems worldwide with system photographs and references and elaborates on the fundamentals of hybrid systems and their performances with thermal modelling. Energy and exergy analysis, techno-economic analysis and carbon trading are key chapters for research professionals. The book also includes important case studies to aid understanding of the subject for all readers.
Download or read book Solar Energy Engineering written by Soteris A Kalogirou and published by Academic Press. This book was released on 2009-07-22 with total page 779 pages. Available in PDF, EPUB and Kindle. Book excerpt: As perhaps the most promising of all the renewable energy sources available today, solar energy is becoming increasingly important in the drive to achieve energy independence and climate balance. This new book is the masterwork from world-renowned expert Dr. Soteris Kalogirou, who has championed solar energy for decades. The book includes all areas of solar energy engineering, from the fundamentals to the highest level of current research. The author includes pivotal subjects such as solar collectors, solar water heating, solar space heating and cooling, industrial process heat, solar desalination, photovoltaics, solar thermal power systems, and modeling of solar systems, including the use of artificial intelligence systems in solar energy systems, modeling and performance prediction. *Written by one of the world's most renowned experts in solar energy*Covers the hottest new developments in solar technology, such as solar cooling and desalination*Packed with quick look up tables and schematic diagrams for the most commonly used systems today'
Download or read book Facade Construction Manual written by Thomas Herzog and published by Walter de Gruyter. This book was released on 2012-12-10 with total page 320 pages. Available in PDF, EPUB and Kindle. Book excerpt: Facades - they are the first feature of a building to be noticed, they determine its distinctive appearance and are often the subject of controversial debate. This new first edition of the Facade Construction Manual provides a systematic survey of contemporary expertise in the application of new materials and energy- efficient technologies in facade design, and represents an invaluable addition to our series of Construction Manuals. It surveys the facade design requirements made by various types of buildings, as well as the most important materials, from natural stone through to synthetics, and documents a diversity of construction forms for a wide range of building types. Over 100 international case-studies in large-scale, detailed drawings are presented in the comprehensive project section.
Download or read book Solar Energy written by Arno Smets and published by Bloomsbury Publishing. This book was released on 2016-01-28 with total page 488 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a broad overview on the different aspects of solar energy, with a focus on photovoltaics, which is the technology that allows light energy to be converted into electric energy. Renewable energy sources have become increasingly popular in recent years, and solar is one of the most adaptable and attractive types – from solar farms to support the National Grid to roof panels/tiles used for solar thermal heating systems, and small solar garden lights. Written by Delft University researchers, Solar Energy uniquely covers both the physics of photovoltaic (PV) cells and the design of PV systems for real-life applications, from a concise history of solar cells components and location issues of current systems. The book is designed to make this complicated subject accessible to all, and is packed with fascinating graphs and charts, as well as useful exercises to cement the topics covered in each chapter. Solar Energy outlines the fundamental principles of semiconductor solar cells, as well as PV technology: crystalline silicon solar cells, thin-film cells, PV modules, and third-generation concepts. There is also background on PV systems, from simple stand-alone to complex systems connected to the grid. This is an invaluable reference for physics students, researchers, industrial engineers and designers working in solar energy generation, as well those with a general interest in renewable energy.
Download or read book Sustainable Energy Technologies written by Eduardo Rincón-Mejía and published by CRC Press. This book was released on 2017-11-20 with total page 399 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book examines the key aspects that will define future sustainable energy systems: energy supply, energy storage, security and limited environmental impacts. It clearly explains the need for an integrated engineering approach to sustainable energies, based on mathematical, biogeophysical, and engineering arguments. Resilient and efficient alternatives are compared to non-sustainable options. This book results from the collaboration of 50 international contributors.
Download or read book Reliability and Ecological Aspects of Photovoltaic Modules written by Abdulkerim Gok and published by BoD – Books on Demand. This book was released on 2020-01-08 with total page 171 pages. Available in PDF, EPUB and Kindle. Book excerpt: Photovoltaic (PV) solar energy is expected to be the world's largest source of electricity in the future. To enhance the long-term reliability of PV modules, a thorough understanding of failure mechanisms is of vital importance. In addition, it is important to address the potential downsides to this technology. These include the hazardous chemicals needed for manufacturing solar cells, especially for thin-film technologies, and the large number of PV modules disposed of at the end of their lifecycles. This book discusses the reliability and environmental aspects of PV modules.
Download or read book Solar Energy written by Christoph Richter and published by Springer. This book was released on 2012-11-29 with total page 744 pages. Available in PDF, EPUB and Kindle. Book excerpt: Gathering some 30 entries from the Encyclopedia of Sustainability Science and Technology, this book presents fundamental principles and technologies for sustainably harnessing solar energy. Covers photovoltaics, solar thermal energy, solar radiation and more.
Download or read book Grid Connected PV Plants written by Ángel Molina-García and published by . This book was released on 2020 with total page 198 pages. Available in PDF, EPUB and Kindle. Book excerpt: PV power plant integration into the grid has been a relevant topic of interest over the last years. Policies supported by governments, technology maturity, favorable incentives, and cost decreasing have significantly promoted the integration of PV power plants into power systems at the transmission and distribution levels. Nevertheless, some barriers remain in terms of forecasting generation, grid reliability, and power quality, which must be overcome for the massive PV integration into future power systems. Additionally, the ancillary services provided by these generation units are increasingly required by different agents to facilitate grid operation under a high proportion of renewables. Topics of interest for this Special Issue include the following areas: large-scale PV power plants, energy policies related to PV power plants, grid integration and interaction, PV power plant modeling, monitoring and case studies, communication systems for PV power plants integration, economic analyses, PV inverters and sizing analyses, new trends in PV technologies, and reviews.
Download or read book Durability and Reliability of Polymers and Other Materials in Photovoltaic Modules written by Hsinjin Edwin Yang and published by William Andrew. This book was released on 2019-04-15 with total page 356 pages. Available in PDF, EPUB and Kindle. Book excerpt: Durability and Reliability of Polymers and Other Materials in Photovoltaic Modules describes the durability and reliability behavior of polymers used in Si-photovoltaic modules and systems, particularly in terms of physical aging and degradation process/mechanisms, characterization methods, accelerated exposure chamber and testing, module level testing, and service life prediction. The book compares polymeric materials to traditional materials used in solar applications, explaining the degradation pathways of the different elements of a photovoltaic module, including encapsulant, front sheet, back sheet, wires and connectors, adhesives, sealants, and more. In addition, users will find sections on the tests needed for the evaluation of polymer degradation and aging, as well as accelerated tests to aid in materials selection. As demand for photovoltaics continues to grow globally, with polymer photovoltaics offering significantly lower production costs compared to earlier approaches, this book will serve as a welcome resource on new avenues. Provides comprehensive coverage of photovoltaic polymers, from fundamental degradation mechanisms, to specific case studies of durability and materials failure Offers practical, actionable information in relation to service life prediction of photovoltaic modules and accelerated testing for materials selection Includes up-to-date information and interpretation of safety regulations and testing of photovoltaic modules and materials
Download or read book Wind and Solar Power Systems written by Mukund R. Patel and published by CRC Press. This book was released on 2021-03-23 with total page 406 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides technological and socio-economic coverage of renewable energy. It discusses wind power technologies, solar photovoltaic technologies, large-scale energy storage technologies, and ancillary power systems. In this new edition, the book addresses advancements that have been made in renewable energy: grid-connected power plants, power electronics converters, and multi-phase conversion systems. The text has been revised to include up-to-date material, statistics, and current technology trends. Three new chapters have been added to cover turbine generators, AC and DC wind systems, and recent advances solar power conversion. Discusses additional renewable energy sources, such as ocean, special turbines, etc. Covers system integration for solar and wind energy Presents emerging DC wind systems Includes coverage on turbine generators Updated sections on solar power conversion It offers students, practicing engineers, and researchers a comprehensive look at wind and solar power technologies. It is designed as a reference and can serve as a textbook for senior undergraduates in a one-semester course on renewable power or energy systems.
Download or read book Nanotechnology in Construction written by Peter J M Bartos and published by Royal Society of Chemistry. This book was released on 2007-10-31 with total page 397 pages. Available in PDF, EPUB and Kindle. Book excerpt: The importance of nanotechnology related research and development has become recognised worldwide. Substantial public and private investment is now being ploughed into research and development in a number of industrial sectors, where nanotechnology has become established and has led to new commercial products. The construction industry, having major economic significance with nano-scale research and development which is only emerging, offers a wide scope for exploitation of nanotechnology. With international contributions from experts in the field, Nanotechnology in Construction amalgamates previously fragmented research and emerging trends. It reflects the inherent multi-disciplinary nature of nano-scale research in construction and contributions cover a wide spectrum, from highly scientific investigations to futuristic applications. The book is organised into four broad sections, the first reviews and analyses the prospects of exploitation of nanotechnology in construction, the second discusses novel tools and their capabilities, the final two sections show existing significant products where nanotechnology has been already been exploited or where product development is under-way. Nanotechnology in Construction will appeal to researchers already working in this field as well as those wishing to enter it. It will also inform governmental and other funding agencies of the most promising future directions and their related timescales. Practical applications are considered and explanations of the underlying basics are given, raising awareness and understanding of what nanotechnology can offer to construction professionals in general.
Download or read book Alternative Energy Systems in Building Design GreenSource Books written by Peter Gevorkian and published by McGraw Hill Professional. This book was released on 2009-09-07 with total page 545 pages. Available in PDF, EPUB and Kindle. Book excerpt: Design High-Performance Alternative Energy Systems for Buildings A comprehensive reference for architects and engineers, this GreenSource book provides practical design and installation guidelines for some of the most commercially viable alternative energy technologies. Construction materials, system deployment, typical installations, and environmental impact are covered. Alternative Energy Systems in Building Design includes information on LEED design, energy conservation, and solar power financing and return on investment. Power purchase agreements (PPAs) and national and international carbon cap and trade are also discussed. Valuable appendices contain detailed design data tables and certified equipment listings. Alternative Energy Systems in Building Design covers: Solar power system physics and technologies California solar initiative program Energy conservation Passive heating solar technologies Fuel cell technology Wind energy technologies Ocean energy technologies Hydroelectric and micro-hydro turbine power Geothermal energy Biofuel, biogas, and thermal depolymerization technologies Fission- and fusion-type nuclear power Air pollution abatement
Download or read book Solar Cells written by Tom Markvart and published by Academic Press. This book was released on 2012-10-26 with total page 655 pages. Available in PDF, EPUB and Kindle. Book excerpt: Enormous leaps forward in the efficiency and the economy of solar cells are being made at a furious pace. New materials and manufacturing processes have opened up new realms of possibility for the application of solar cells. Crystalline silicon cells are increasingly making way for thin film cells, which are spawning experimentation with third-generation high-efficiency multijunction cells, carbon-nanotube based cells, UV light for voltage enhancement, and the use of the infrared spectrum for night-time operation, to name only a few recent advances. This thoroughly updated new edition of Markvart and Castaner's Solar Cells, extracted from their industry standard Practical Handbook of Photovoltaics, is the definitive reference covering the science and operation, materials and manufacture of solar cells. It is essential reading for engineers, installers, designers, and policy-makers who need to understand the science behind the solar cells of today, and tomorrow, in order to take solar energy to the next level. A thorough update to the definitive reference to solar cells, created by a cast of international experts from industry and academia to ensure the highest quality information from multiple perspectives Covers the whole spectrum of solar cell information, from basic scientific background, to the latest advances in materials, to manufacturing issues, to testing and calibration. Case studies, practical examples and reports on the latest advances take the new edition of this amazing resource beyond a simple amalgamation of a vast amount of knowledge, into the realm of real world applications
