Download or read book Lab Manual for Electronics written by Martin Feldman and published by Prentice Hall. This book was released on 2001-11 with total page 132 pages. Available in PDF, EPUB and Kindle. Book excerpt: The emphasis is first on understanding the characteristics of basic circuits including resistors, capacitors, diodes, and bipolar and field effect transistors. The readers then use this understanding to construct more complex circuits such as power supplies, differential amplifiers, tuned circuit amplifiers, a transistor curve tracer, and a digital voltmeter. In addition, readers are exposed to special topics of current interest, such as the propagation and detection of signals through fiber optics, the use of Van der Pauw patterns for precise linewidth measurements, and high gain amplifiers based on active loads. KEY TOPICS: Chapter topics include Thevenin's Theorem; Resistive Voltage Division; Silicon Diodes; Resistor Capacitor Circuits; Half Wave Rectifiers; DC Power Supplies; Diode Applications; Bipolar Transistors; Field Effect Transistors; Characterization of Op-Amp Circuits; Transistor Curve Tracer; Introduction to PSPICE and AC Voltage Dividers; Characterization and Design of Emitter and Source Followers; Characterization and Design of an AC Variable Gain Amplifier; Design of Test Circuits for BJT's and FET's and Design of FET Ring Oscillators; Design and Characterization of Emitter Coupled Transistor Pairs; Tuned Amplifier and Oscillator; Design of Am Radio Frequency Transmitter and Receiver; Design of Oscillators Using Op-Amps; Current Mirrors and Active Loads; Sheet Resistance; Design of Analog Fiber Optic Transmission System; Digital Voltmeter.

Download or read book Ed Lab 650 Experiment Manual written by CES Industries, Inc. Staff and published by Ces Industries. This book was released on 1981-01-01 with total page 288 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book ELECTRONICS LAB MANUAL VOLUME 2 written by NAVAS, K. A. and published by PHI Learning Pvt. Ltd.. This book was released on 2018-10-01 with total page 372 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is evolved from the experience of the author who taught all lab courses in his three decades of teaching in various universities in India. The objective of this lab manual is to provide information to undergraduate students to practice experiments in electronics laboratories. This book covers 118 experiments for linear/analog integrated circuits lab, communication engineering lab, power electronics lab, microwave lab and optical communication lab. The experiments described in this book enable the students to learn: • Various analog integrated circuits and their functions • Analog and digital communication techniques • Power electronics circuits and their functions • Microwave equipment and components • Optical communication devices This book is intended for the B.Tech students of Electronics and Communication Engineering, Electrical and Electronics Engineering, Biomedical Electronics, Instrumentation and Control, Computer Science, and Applied Electronics. It is designed not only for engineering students, but can also be used by BSc/MSc (Physics) and Diploma students. KEY FEATURES • Contains aim, components and equipment required, theory, circuit diagram, pin-outs of active devices, design, tables, graphs, alternate circuits, and troubleshooting techniques for each experiment • Includes viva voce and examination questions with their answers • Provides exposure on various devices TARGET AUDIENCE • B.Tech (Electronics and Communication Engineering, Electrical and Electronics Engineering, Biomedical Electronics, Instrumentation and Control, Computer Science, and Applied Electronics) • BSc/MSc (Physics) • Diploma (Engineering)

Download or read book Lab Manual for Electronic Devices Global Edition written by THOMAS L. FLOYD and published by . This book was released on 2018-06-19 with total page 288 pages. Available in PDF, EPUB and Kindle. Book excerpt: This laboratory manual is carefully coordinated to the text Electronic Devices, Tenth edition, Global edition, by Thomas L. Floyd. The seventeen experiments correspond to the chapters in the text (except the first experiment references Chapters 1 and the first part of Chapter 2). All of the experiments are subdivided into two or three "Parts." With one exception (Experiment 12-B), the Parts for the all experiments are completely independent of each other. The instructor can assign any or all Parts of these experiments, and in any order. This format provides flexibility depending on the schedule, laboratory time available, and course objectives. In addition, experiments 12 through 16 provide two options for experiments. These five experiments are divided into two major sections identified as A or B. The A experiments continue with the format of previous experiments; they are constructed with discrete components on standard protoboards as used in most electronic teaching laboratories. The A experiments can be assigned in programs where traditional devices are emphasized. Each B experiment has a similar format to the corresponding A experiment, but uses a programmable Analog Signal Processor (ASP) that is controlled by (free) Computer Aided Design (CAD) software from the Anadigm company (www.anadigm.com). These experiments support the Programmable Analog Design feature in the textbook. The B experiments are also subdivided into independent Parts, but Experiment 12-B, Part 1, is a software tutorial and should be performed before any other B experiments. This is an excellent way to introduce the ASP technology because no other hardware is required other than a computer running the downloaded software. In addition to Experiment 12-B, the first 13 steps of Experiment 15-B, Part 2, are also tutorial in nature for the AnadigmFilter program. This is an amazing active filter design tool that is easy to learn and is included with the AnadigmDesigner2 (AD2) CAD software. The ASP is part of a Programmable Analog Module (PAM) circuit board from the Servenger company (www.servenger.com) that interfaces to a personal computer. The PAM is controlled by the AD2 CAD software from the Anadigm company website. Except for Experiment 12-B, Part 1, it is assumed that the PAM is connected to the PC and AnadigmDesigner2 is running. Experiment 16-B, Part 3, also requires a spreadsheet program such as Microsoft® Excel®. The PAM is described in detail in the Quick Start Guide (Appendix B). Instructors may choose to mix A and B experiments with no loss in continuity, depending on course objectives and time. We recommend that Experiment 12-B,Part 1, be assigned if you want students to have an introduction to the ASP without requiring a hardware purchase. A text feature is the Device Application (DA) at the end of most chapters. All of the DAs have a related laboratory exercise using a similar circuit that is sometimes simplified to make laboratory time as efficient as possible. The same text icon identifies the related DA exercise in the lab manual. One issue is the trend of industry to smaller surface-mount devices, which are very difficult to work with and are not practical for most lab work. For example, almost all varactors are supplied as surface mount devices now. In reviewing each experiment, we have found components that can illustrate the device function with a traditional one. The traditional through-hole MV2109 varactor is listed as obsolete, but will be available for the foreseeable future from Electronix Express (www.elexp.com), so it is called out in Experiment 3. All components are available from Electronix Express (www.elexp.com) as a kit of parts (see list in Appendix A). The format for each experiment has not changed from the last edition and is as follows: · Introduction: A brief discussion about the experiment and comments about each of the independent Parts that follow. · Reading: Reading assignment in the Floyd text related to the experiment. · Key Objectives: A statement specific to each Part of the experiment of what the student should be able to do. · Components Needed: A list components and small items required for each Part but not including the equipment found at a typical lab station. Particular care has been exercised to select materials that are readily available and reusable, keeping cost at a minimum. · Parts: There are two or three independent parts to each experiment. Needed tables, graphs, and figures are positioned close to the first referenced location to avoid confusion. Step numbering starts fresh with each Part, but figures and tables are numbered sequentially for the entire experiment to avoid multiple figures with the same number. § Conclusion: At the end of each Part, space is provided for a written conclusion. § Questions: Each Part includes several questions that require the student to draw upon the laboratory work and check his or her understanding of the concepts. Troubleshooting questions are frequently presented. · Multisim Simulation: At the end of each A experiment (except #1), one or more circuits are simulated in a Multisim computer simulation. New Multisim troubleshooting problems have been added to this edition. Multisim troubleshooting files are identified with the suffix f1, f2, etc., in the file name (standing for fault1, fault2, etc.). Other files, with nf as the suffix include demonstrations or practice using instruments such as the Bode Plotter and the Spectrum Analyzer. A special icon is shown with all figures that are related to the Multisim simulation. Multisim files are found on the website: www.pearsonglobaledition.com/Floyd. Microsoft PowerPoint® slides are available at no cost to instructors for all experiments. The slides reinforce the experiments with troubleshooting questions and a related problem and are available on the instructor''s resource site. Each laboratory station should contain a dual-variable regulated power supply, a function generator, a multimeter, and a dual-channel oscilloscope. A list of all required materials is given in Appendix A along with information on acquiring the PAM. As mentioned, components are also available as a kit from Electronix Express; the kit number is 32DBEDFL10.

Download or read book Ed Lab Experiment Manual written by CES Industries, Inc. Staff and published by . This book was released on 1983-01-01 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book The Complete Lab Manual for Electricity written by Stephen L. Herman and published by Cengage Learning. This book was released on 2008-02-25 with total page 480 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Complete Laboratory Manual for Electricity, 3rd Edition is a valuable tool designed to fit into any basic electrical program that incorporates lab experience. This updated edition will enhance your lab practices and the understanding of electrical concepts. From basic electricity through AC theory, transformers, and motor controls, all aspects of a typical electrical curriculum are explored in a single volume. Each lab features an explanation of the circuit to be connected, with examples of the calculations necessary to complete the exercise and step-by-step procedures for conducting the experiment. Hands-on experiments that acquaint readers with the theory and application of electrical concepts offer valuable experience in constructing a multitude of circuits such as series, parallel, combination, RL series and parallel, RC series and parallel, and RLC series and parallel circuits. Important Notice: Media content referenced within the product description or the product text may not be available in the ebook version.

Download or read book Ed Lab Experiment Manual written by CES Industries, Inc. Staff and published by . This book was released on 1983-07-01 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Lab Manual Latest Edition written by Dr. J. P. Goel and published by SBPD Publications. This book was released on 2016-12-17 with total page 178 pages. Available in PDF, EPUB and Kindle. Book excerpt: Lab. E- Manual Physics (For XIIth Practicals) A. Every student will perform 10 experiments (5 from each section) & 8 activities (4 from each section) during the academic year. Two demonstration experiments must be performed by the teacher with participation of students. The students will maintain a record of these demonstration experiments. B. Evaluation Scheme for Practical Examination : One experiment from any one section 8 Marks Two activities (one from each section) (4 + 4) 8 Marks Practical record (experiments & activities) 6 Marks Record of demonstration experiments & Viva based on these experiments 3 Marks Viva on experiments & activities 5 Marks Total 30 Marks Section A Experiments 1. To determine resistance per cm of a given wire by plotting a graph of potential difference versus current. 2. To find resistance of a given wire using metre bridge and hence determine the specific resistance of its material. 3. To verify the laws of combination (series/parallel) of resistances using a metre bridge. 4. To compare the emf of two given primary cells using potentiometer. 5. To determine the internal resistance of given primary cells using potentiometer. 6. To determine resistance of a galvanometer by half-deflection method and to find its figure of merit. 7. To convert the given galvanometer (of known resistance and figure of merit) into an ammeter and voltmeter of desired range and to verify the same. 8. To find the frequency of the a.c. mains with a sonometer. Activities 1. To measure the resistance and impedance of an inductor with or without iron core. 2. To measure resistance, voltage (AC/DC), current (AC) and check continuity of a given circuit using multimeter. 3. To assemble a household circuit comprising three bulbs, three (on/off) switches, a fuse and a power source. 4. To assemble the components of a given electrical circuit. 5. To study the variation in potential drop with length of a wire for a steady current. 6. To draw the diagram of a given open circuit comprising at least a battery, resistor/rheostat, key, ammeter and voltmeter. Mark the components that are not connected in proper order and correct the circuit and also the circuit diagram. Section B Experiments 1. To find the value of v for different values of u in case of a concave mirror and to find the focal length. 2. To find the focal length of a convex lens by plotting graphs between u and v or between 1/u and 1/u. 3. To find the focal length of a convex mirror, using a convex lens. 4. To find the focal length of a concave lens, using a convex lens. 5. To determine angle of minimum deviation for a given prism by plotting a graph between angle of incidence and angle of deviation. 6. To determine refractive index of a glass slab using a travelling microscope. 7. To find refractive index of a liquid by using (i) concave mirror, (ii) convex lens and plane mirror. 8. To draw the I-V characteristic curve of a p-n junction in forward bias and reverse bias. 9. To draw the characteristic curve of a zener diode and to determine its reverse break down voltage. 10. To study the characteristics of a common-emitter npn or pnp transistor and to find out the values of current and voltage gains. Activitie 1. To study effect of intensity of light (by varying distance of the source) on a L.D.R. 2. To identify a diode, a LED, a transistor and IC, a resistor and a capacitor from mixed collection of such items. 3. Use of multimeter to (i) identify base of transistor. (ii) distinguish between npn and pnp type transistors. (iii) see the unidirectional flow of current in case of a diode and a LED. (iv) check whether a given electronic component (e.g. diode, transistor or I C) is in working order. 4. To observe refraction and lateral deviation of a beam of light incident obliquely on a glass slab. 5. To observe polarization of liquid using two Polaroids. 6. To observe diffraction of light due to a thin slit. 7. To study the nature and size of the image formed by (i) convex lens, (ii) concave mirror, on a screen by using a candle and a screen (for different distances of the candle from the lens/mirror). 8. To obtain a lens combination with the specified focal length by using two lenses from the given set of lenses. Suggested Investigatory Projects 1. To investigate whether the energy of a simple pendulum is conserved. 2. To determine the radius of gyration about the centre of mass of a metre scale as a bar pendulum. 3. To investigate changes in the velocity of a body under the action of a constant force and determine its acceleration. 4. To compare effectiveness of different materials as insulators of heat. 5. To determine the wavelengths of laser beam by diffraction. 6. To study various factors on which the internal resistance/emf of a cell depends. 7. To construct a time-switch and study dependence of its time constant on various factors. 8. To study infrared radiations emitted by different sources using photo-transistor. 9. To compare effectiveness of different materials as absorbers of sound. 10. To design an automatic traffic signal system using suitable combination of logic gates. 11. To study luminosity of various electric lamps of different powers and make. 12. To compare the Young’s modulus of elasticity of different specimens of rubber and also draw their elastic hysteresis curve. 13. To study collision of two balls in two dimensions. 14. To study frequency response of : (i) a resistor, an inductor and a capacitor, (ii) RL circuit, (iii) RC circuit, (iv) LCR series circuit.

Download or read book Experimental Education written by Frank Nugent Freeman and published by . This book was released on 1916 with total page 240 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Ed Lab Six Hundred and Fifty Experiment Manual written by CES Industries, Inc. Staff and published by . This book was released on 1980-01-01 with total page 206 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Ed Lab Six Hundred and Fifty Experiment Manual written by CES Industries, Inc. Staff and published by . This book was released on 1981-01-01 with total page 304 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Ed Lab Experiment Manual written by CES Computers, Inc and published by . This book was released on 1972 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Ed Lab Experiment Manual written by CES Industries, Inc. Staff and published by . This book was released on 1980-01-01 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Ed Lab Six Hundred and Fifty Experiment Manual written by CES Industries, Inc. Staff and published by . This book was released on 1980-01-01 with total page 288 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Ed Lab Experiment Manual written by and published by . This book was released on 1973 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Ed Lab Sixty Three Experiment Manual written by CES Industries, Inc. Staff and published by . This book was released on 1982-01-01 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Ed Lab Experiment Manual written by CES Industries, Inc. Staff and published by . This book was released on 1983 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: