Download or read book Dynamic Modelling and Fault Feature Analysis of Gear Tooth Pitting and Spalling written by Yang Luo and published by . This book was released on 2019 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Fault feature analysis of gear tooth spall plays a vital role in gear fault diagnosis. Knowing the characteristic of fault features and their evolution as a gear tooth fault progresses is key to fault severity assessment. This thesis provides a comprehensive (both theoretical and experimental) analysis of the fault vibration features of a gear transmission with progressive localized gear tooth pitting and spalling. A dynamic model of a one-stage spur gear transmission is proposed to analyze the vibration behavior of a gear transmission with tooth fault. The proposed dynamic model considers the effects of Time Varying Mesh Stiffness (TVMS), tooth surface roughness changes and geometric deviations due to pitting and spalling, and also incorporates a time-varying load sharing ratio, as well as dynamic tooth contact friction forces, friction moments and dynamic mesh damping ratios. The gear dynamical model is validated by comparison with responses obtained from an experimental test rig under different load and fault conditions. In addition, several methods are proposed for the evaluation of the TVMS of a gear pair with tooth spall(s) with curved bottom and irregular shapes, which fills the current research gap on modelling tooth spalls with irregular shapes and randomly distribution conditions. Experiments are conducted and the fault vibration features and their evolution as the tooth fault progresses are analyzed. Based on feature analysis, a new health indicator is proposed to detect progressive localized tooth spall.
Download or read book Proceedings of the 10th International Conference on Rotor Dynamics IFToMM written by Katia Lucchesi Cavalca and published by Springer. This book was released on 2018-08-18 with total page 586 pages. Available in PDF, EPUB and Kindle. Book excerpt: IFToMM conferences have a history of success due to the various advances achieved in the field of rotor dynamics over the past three decades. These meetings have since become a leading global event, bringing together specialists from industry and academia to promote the exchange of knowledge, ideas, and information on the latest developments in the dynamics of rotating machinery. The scope of the conference is broad, including e.g. active components and vibration control, balancing, bearings, condition monitoring, dynamic analysis and stability, wind turbines and generators, electromechanical interactions in rotor dynamics and turbochargers. The proceedings are divided into four volumes. This second volume covers the following main topics: condition monitoring, fault diagnostics and prognostics; modal testing and identification; parametric and self-excitation in rotor dynamics; uncertainties, reliability and life predictions of rotating machinery; and torsional vibrations and geared systems dynamics.
Download or read book Proceedings of the UNIfied Conference of DAMAS IncoME and TEPEN Conferences UNIfied 2023 written by Andrew D. Ball and published by Springer Nature. This book was released on with total page 1186 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Proceedings of the TEPEN International Workshop on Fault Diagnostic and Prognostic written by Tongtong Liu and published by Springer Nature. This book was released on with total page 608 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Proceedings of IncoME VI and TEPEN 2021 written by Hao Zhang and published by Springer Nature. This book was released on 2022-09-17 with total page 1074 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume gathers the latest advances, innovations and applications in the field of condition monitoring, plant maintenance and reliability, as presented by leading international researchers and engineers at the 6th International Conference on Maintenance Engineering and the 2021 conference of the Efficiency and Performance Engineering Network (IncoME-VI TEPEN 2021), held in Tianjin, China on October 20-23, 2021. Topics include vibro-acoustics monitoring, condition-based maintenance, sensing and instrumentation, machine health monitoring, maintenance auditing and organization, non-destructive testing, reliability, asset management, condition monitoring, life-cycle cost optimisation, prognostics and health management, maintenance performance measurement, manufacturing process monitoring, and robot-based monitoring and diagnostics. The contributions, which were selected through a rigorous international peer-review process, share exciting ideas that will spur novel research directions and foster new multidisciplinary collaborations.
Download or read book Developments and Novel Approaches in Nonlinear Solid Body Mechanics written by Bilen Emek Abali and published by Springer Nature. This book was released on 2020-07-18 with total page 491 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book features selected manuscripts presented at ICoNSoM 2019, exploring cutting-edge methods for developing novel models in nonlinear solid mechanics. Innovative methods like additive manufacturing—for example, 3D printing— and miniaturization mean that engineers need more accurate techniques for modeling solid body mechanics. The book focuses on the formulation of continuum and discrete models for complex materials and systems, particularly the design of metamaterials.
Download or read book Development of a Model Based Technique for Gear Diagnostics Using the Wigner Ville Method written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-07-17 with total page 168 pages. Available in PDF, EPUB and Kindle. Book excerpt: Imperfections in gear tooth geometry often result from errors in the manufacturing process or excessive material wear during operation. Such faults in the gear tooth geometry can result in large vibrations in the transmission system, and, in some cases, may lead to early failure of the gear transmission system. This report presents the study of the effects of imperfection in gear tooth geometry on the dynamic characteristics of a gear transmission system. The faults in the gear tooth geometry are modeled numerically as the deviation of the tooth profile from its original involute geometry. The changes in gear mesh stiffness due to various profile and pattern variations are evaluated numerically. The resulting changes in the mesh stiffness are incorporated into a computer code to simulate the dynamics of the gear transmission system. A parametric study is performed to examine the sensitivity of gear tooth geometry imperfections on the vibration of a gear transmission system. The parameters variations in this study consist of the magnitude of the imperfection, the pattern of the profile variation, and the total number of teeth affected. Numerical results from the dynamic simulations are examined in both the time and the frequency domains. A joint time-frequency analysis procedure using the Wigner-Ville Distribution is also introduced to identify the location of the damaged tooth from the vibration signature. Numerical simulations of the system dynamics with gear faults were compared to experimental results. An optimal tracker was introduced to quantify the level of damage in the gear mesh system. Conclusions are drawn from the results of this numerical study. Choy, F. and Xu, A. and Polyshchuk, V. Glenn Research Center GEARS; GEAR TEETH; DYNAMIC CHARACTERISTICS; DEFECTS; MATHEMATICAL MODELS; TRANSMISSIONS (MACHINE ELEMENTS); FAULT DETECTION; GEOMETRIC ACCURACY; STIFFNESS; TIME DEPENDENCE; FREQUENCIES; SYSTEMS HEALTH MONITORING; VIBRATION EFFECTS...
Download or read book Dynamics and Fault Diagnosis of Nonlinear Rotors and Impellers written by Jiazhong Zhang and published by Springer Nature. This book was released on 2022-04-28 with total page 281 pages. Available in PDF, EPUB and Kindle. Book excerpt: This contributed volume presents recent developments in nonlinear dynamics applied to engineering. Specifically, the authors address stability and bifurcation in large-scale, complex rotor dynamic systems; periodic motions and their bifurcations in nonlinear circuit systems, fault diagnosis of complex engineering systems with nonlinear approaches, singularities in fluid-machinery and bifurcation analysis, nonlinear behaviors in rotor dynamic system with multi-mistuned blades, mode localization induced by mistuning in impellers with periodical and cyclic symmetry, and nonlinear behaviors in fluid-structure interaction and their control. These new results will maximize reader understand on the recent progress in nonlinear dynamics applied to large-scale, engineering systems in general and nonlinear rotors and impellers in particular.
Download or read book Predicted Effect of Dynamic Load on Pitting Fatigue Life for Low contact ratio Spur Gears written by David G. Lewicki and published by . This book was released on 1986 with total page 24 pages. Available in PDF, EPUB and Kindle. Book excerpt: How dynamic load affects the surface pitting fatigue life of external spur gears was predicted by using NASA computer program TELSGE. Parametric studies were performed over a range of various gear parameters modeling low-contact-ratio involute spur gears. In general, gear life predictions based on dynamic loads differed significantly from those based on static loads, with the predictions being strongly influenced by the maximum dynamic load during contact. Gear mesh operating speed strongly affected predicted dynamic load and life. Meshes operating at a resonant speed or one-half the resonant speed had significantly shorter lives. Dynamic life factors for gear surface pitting fatigue were developed on the basis of the parametric studies. In general, meshes with higher contact ratios had higher dynamic life factors than meshes with lower contact ratios. A design chart was developed for hand calculations of dynamic life factors. (Author).
Download or read book Systematic Analysis of Gear Failures written by Lester E. Alban and published by ASM International. This book was released on 1985-01-01 with total page 252 pages. Available in PDF, EPUB and Kindle. Book excerpt: Explores the detailed steps necessary to determine the causes of failure. First, the physical characteristics of a gear are studied: where the stress points are, from what directions the forces are applied, where the movement of material progresses, and where strain patterns exist. Second, all external conditions and forces are considered. With this background information, a systematic examination is described from beginning to end, the end being a conclusion about the mode and cause of failure.
Download or read book An Analysis of Gear Fault Detection Methods as Applied to Pitting Fatigue Failure Data written by and published by . This book was released on 1993 with total page 16 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Modelling and Simulation of Complex Systems for Sustainable Energy Efficiency written by Ahmed Hammami and published by Springer Nature. This book was released on 2021-08-21 with total page 270 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides readers with an overview of recent theories and methods for studying complex mechanical systems used in energy production, such as wind turbines, but not limited to them. The emphasis is put on strategies for increasing energy efficiency, and on recent industrial applications. Topics cover dynamics and vibration, vibroacoustics, engineering design, modelling and simulation, fault diagnostics, signal processing and prognostics. The book is based on peer-review contributions and invited talks presented at the first International Workshop on MOdelling and Simulation of COmplex Systems for Sustainable Energy Efficiency, MOSCOSSEE 2021, held online on February 25-26, 2021, and organized by the LAboratory of Mechanics, Modelling and Production (LA2MP) from University of Sfax, Tunisia and the Department of Mechanical and Aeronautical engineering, Centre of Asset Integrity Management (C-AIM) from University of Pretoria, South Africa. By offering authoritative information on innovative methods and tools for application in renewable energy production, it provides a valuable resource to both academics and professionals, and a bridge to facilitate communication between the two groups.
Download or read book Advanced Tribology written by Jianbin Luo and published by Springer Science & Business Media. This book was released on 2010-07-16 with total page 1040 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Advanced Tribology" is the proceedings of the 5th China International Symposium on Tribology (held every four years) and the 1st International Tribology Symposium of IFToMM, held in Beijing 24th-27th September 2008. It contains seven parts: lubrication; friction and wear; micro/nano-tribology; tribology of coatings, surface and interface; biotribology; tribo-chemistry; industry tribology. The book reflects the recent progress in the fields such as lubrication, friction and wear, coatings, and precision manufacture etc. in the world. The book is intended for researchers, engineers and graduate students in the field of tribology, lubrication, mechanical production and industrial design. The editors Jianbin Luo, Yonggang Meng, Tianmin Shao and Qian Zhao are all the professors at the State Key Lab of Tribology, Tsinghua University, Beijing.
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1995 with total page 464 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Engineering Asset Management Systems Professional Practices and Certification written by Peter W. Tse and published by Springer. This book was released on 2014-12-09 with total page 1758 pages. Available in PDF, EPUB and Kindle. Book excerpt: This proceeding represents state-of-the-art trends and developments in the emerging field of engineering asset management as presented at the Eight World Congress on Engineering Asset Management (WCEAM). The Proceedings of the WCEAM 2013 is an excellent reference for practitioners, researchers and students in the multidisciplinary field of asset management, covering topics such as: Asset condition monitoring and intelligent maintenance, 2. Asset data warehousing, data mining and fusion, 3. Asset performance and level-of-service models, 4. Design and life-cycle integrity of physical assets, 5. Deterioration and preservation models for assets, 6. Education and training in asset management, 7. Engineering standards in asset management, 8. Fault diagnosis and prognostics, 9. Financial analysis methods for physical assets, 10. Human dimensions in integrated asset management, 11. Information quality management, 12. Information systems and knowledge management, 13. Intelligent sensors and devices, 14. Maintenance strategies in asset management, 15. Optimisation decisions in asset management, 16. Risk management in asset management, 17. Strategic asset management, 18. Sustainability in asset management. King WONG served as Congress Chair for WCEAM 2013 and ICUMAS 2013 is the President of the Hong Kong Institute of Utility Specialists (HKIUS) and Convener of International Institute of Utility Specialists (IIUS). Peter TSE is the Director of the Smart Engineering Asset Management laboratory (SEAM) at the City University of Hong Kong and served as the Chair of WCEAM 2013 Organising Committee. Joseph MATHEW served as the Co-Chair of WCEAM 2013 is also WCEAM’s General Chair. He is the Chief Executive Officer of Asset Institute, Australia.
Download or read book Advances in Acoustics and Vibration III written by Nabih Feki and published by Springer Nature. This book was released on 2021-05-29 with total page 297 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book provides readers with a snapshot of recent research and industrial trends in field of industrial acoustics and vibration. Each chapter, accepted after a rigorous peer-review process, reports on a selected, original piece of work presented and discussed at the Third International Conference on Acoustics and Vibration (ICAV2021), which was organized by the Tunisian Association of Industrial Acoustics and Vibration (ATAVI) and held online on March 15-16, 2021, from Sfax, Tunisia. The contributions cover advances in both theory and practice in a variety of subfields, such as: smart materials and structures; fluid-structure interaction; structural acoustics as well as computational vibro-acoustics and numerical methods. Further topics include: engines control, noise identification, robust design, flow-induced vibration and many others. This book provides a valuable resource for both academics and professionals dealing with diverse issues in applied mechanics. By combining advanced theories with industrial issues, it is expected to facilitate communication and collaboration between different groups of researchers and technology users.
Download or read book Fault Diagnosis and Detection written by Mustafa Demetgul and published by BoD – Books on Demand. This book was released on 2017-05-31 with total page 338 pages. Available in PDF, EPUB and Kindle. Book excerpt: Mass production companies have become obliged to reduce their production costs and sell more products with lower profit margins in order to survive in competitive market conditions. The complexity and automation level of machinery are continuously growing. This development calls for some of the most critical issues that are reliability and dependability of automatic systems. In the future, machines will be monitored remotely, and computer-aided techniques will be employed to detect faults in the future, and also there will be unmanned factories where machines and systems communicate to each other, detect their own faults, and can remotely intercept their faults. The pioneer studies of such systems are fault diagnosis studies. Thus, we hope that this book will contribute to the literature in this regard.
