Download or read book Dynamic Material Properties of Grade 50 Steel written by Matthew P. Murray and published by . This book was released on 2023 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Dynamic Strength Properties of Structural Steel at Elevated Rates of Strain written by Matthew P. Murray and published by . This book was released on 2020 with total page 111 pages. Available in PDF, EPUB and Kindle. Book excerpt: Experiments were conducted on ASTM A572 50 and A992 steel over a range of intermediate strain rates in order to determine material strength properties of structural members subjected to dynamic loadings. The yield and ultimate tensile stress (UTS) of the steels were determined at increasing strain rates using a hydraulic apparatus and compared to static values obtained from ASTM E8 standardized tensile experiments. Results revealed that A572-50 steel exhibited an increase in yield stress of up to 35% and UTS of up to 20% as strain rate increased from 0.002 to 2.0 s-1. A992 steel demonstrated a similar increase in yield stress of up to 45% and UTS of up to 20%. Ratios of dynamic-to-static strengths were used to develop dynamic increase factor curves spanning the range of strain rates studied. These curves provide designers with material property values required for accurate and economical design of protective structures.
Download or read book Dynamic Properties of Materials Part III Steels written by P. Soohoo and published by . This book was released on 1974 with total page 96 pages. Available in PDF, EPUB and Kindle. Book excerpt: A survey of the literature has been conducted to obtain and compile existing experimental data on the pertinent mechanical properties of steels subject to dynamic loading conditions and under a wide temperature range. Data showing the variation of yield strength and elongation with strain rate and temperature are categorized and tabulated. The effect of the dynamic properties of steels due to strain rate variation at room temperature is shown graphically. Separate curves for steels in tension and compression are presented. A comprehensive reference and bibliography section is provided. The behavior of steels under dynamic loading is generally different from that under static loading. The yield strength is higher under dynamic loading, and it decreases with increasing temperature. (Modified author abstract).
Download or read book ANALYSIS AND DESIGN PRACTICE OF STEEL STRUCTURES written by KARUNA MOY GHOSH and published by PHI Learning Pvt. Ltd.. This book was released on 2014-02-11 with total page 349 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is a comprehensive presentation of the fundamental aspects of analysis and design of steel structures. It is primarily meant for the undergraduate students of civil engineering and postgraduate students of structural engineering. It will also be immensely useful for structural engineers engaged in design, consultancy and construction involving steel structures. The important theoretical and practical concepts which need to be assimilated prior to undertaking analysis and design—general principles and practices, functional aspects of structures, basic design concepts, alternative arrangements of equipment and service, clarity of structural behaviour, and calculations of loadings on structures—are covered in the first two chapters. The ensuing chapters provide stepwise presentation of the analysis and design procedures for various steel structures and structural elements/members on the basis of Eurocodes and British (BS) codes of practice. The three types of structures specifically covered, on the basis of functional aspects, are scrap yard structures, conveyor structural systems, and turbo-generator buildings. In the Second Edition, analysis and design of steel structures have been carried out based on Indian Standard code of practice IS 800:2007. Every component of the structure comprising the beams and columns is designed in compliance with the code IS 800:2007. A comparison has been made between the results of the steel structures analysed and designed in compliance with EC3: Part 1-1 and those obtained in accordance with Indian Standard code of practice IS 800:2007. The book discusses the various structural analyses and design calculations in an exhaustive manner. The text is illustrated with an abundant number of visuals. Important sources of information relevant to steel structures can be found in the references at the end of various chapters. Audience Undergraduate students of civil engineering and postgraduate students of structural engineering.
Download or read book SSC written by United States. Ship Structure Committee and published by . This book was released on 1997 with total page 140 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Wind and Seismic Effects written by United States-Japan Cooperative Program in Natural Resources. Panel on Wind and Seismic Effects and published by . This book was released on 1983 with total page 724 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Design of Structures to Resist the Effects of Atomic Weapons written by United States. Army. Corps of Engineers and published by . This book was released on 1957 with total page 104 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fracture and Fatigue Control in Structures written by Stanley Theodore Rolfe and published by ASTM International. This book was released on 1977 with total page 527 pages. Available in PDF, EPUB and Kindle. Book excerpt: Emphasizes applications of fracture mechanics to prevent fracture and fatigue failures in structures, rather than the theoretical aspects of fracture mechanics. The concepts of driving force and resistance force are used to differentiate between the mathematical side and the materials side. Case studies of actual failures are new to the third edition. Annotation copyrighted by Book News, Inc., Portland, OR
Download or read book Tensile Properties of SA 516 Grade 55 Steel in Temperature Range of 25 sup 0 to 927 sup 0 C and Strain Rate Range of 10 sup 4 to 10 sup 1 Sec sup 1 written by and published by . This book was released on 1978 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Tension test results are presented including stress-strain curves obtained in the temperature range of 25 to 927/sup 0/C (75 to 1700/sup 0/F) from specimens of SA 516 (Grade 55) steel, a low carbon pressure vessel steel recommended for cell liners in liquid metal fast nuclear reactors. The tensile properties and stress-strain curves at very high temperatures are required in the analysis and design and in the post-accident integrity analysis of the cell-liners. The values of properties such as yield strength, ultimate tensile strength, reduction in area and total elongation are presented at various test temperatures. Functional relationships between the above properties and test temperature are also presented. In the wide range of temperatures and strain rates at which the tests were performed it was found that the material exhibits dynamic strain aging at temperatures up to about 315/sup 0/C resulting in increased tensile strength and uniform elongation with impaired reduction in area and total elongation. At temperatures above 315/sup 0/C the material gradually loses tensile strength. The strain rate effects on tensile properties are significant and become pronounced at elevated temperatures.
Download or read book Blast Effects on Buildings written by Geoffrey Mays and published by Thomas Telford. This book was released on 1995 with total page 140 pages. Available in PDF, EPUB and Kindle. Book excerpt: This guide is aimed at all engineers and architects involved in building design, focusing on the importance of constructing buildings which minimise damage to people and property in the event of an explosion.
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1991 with total page 1460 pages. Available in PDF, EPUB and Kindle. Book excerpt: Lists citations with abstracts for aerospace related reports obtained from world wide sources and announces documents that have recently been entered into the NASA Scientific and Technical Information Database.
Download or read book Fatigue and Tribological Properties of Plastics and Elastomers written by PDL PDL Staff and published by William Andrew. This book was released on 2013-10-22 with total page 551 pages. Available in PDF, EPUB and Kindle. Book excerpt: For all practical purposes, the useful life of a plastic component is equal to its fatigue life under conditions of cyclic loading such as those that occur in vibration. Equally important to materials engineers and designers are abrasion, friction and wearùtribological properties. Over 80 generic families are covered including thermoplastics, thermosets, thermoplastic elastomers and rubbers. Neat resins, blends and alloys, plastics with various combinations of fillers, additives and more are covered. Also covers plastics mated to plastics and metals.
Download or read book Dynamics written by J. R. Maguire and published by Thomas Telford. This book was released on 2002 with total page 106 pages. Available in PDF, EPUB and Kindle. Book excerpt: A translation of the text by Roberto Tenenbaum (originally published in Portuguese).
Download or read book Geopolymer Concrete Structures with Steel and FRP Reinforcements written by Mohamed Elchalakani and published by Elsevier. This book was released on 2023-02-15 with total page 666 pages. Available in PDF, EPUB and Kindle. Book excerpt: Geopolymer Concrete Structures with Steel and FRP Reinforcements: Analysis and Design focuses on structural behavior, including the aspects of compression, bending strength and combined action of GPC members, with the book's content based on published studies over the last two decades. Geopolymer concrete (GPC) structural members reinforced with FRP reinforcement have some advantages in resisting forces compared to conventional concrete or steel tubular members. Among the most important are the high strength and bending stiffness, fire and impact performance and favorable, construction ability and durability. To this end, there are no significant applications of these new structural elements worldwide, partly due to the lack of the understanding of their behavior and insufficient design provisions in different design manuals. This book, therefore, seeks to highlight their characteristics and future potential. - Provides comprehensive, up-to-date advances on Geopolymer Concrete (GPC) reinforced with steel and FRP bars and stirrups construction with a summary of over 100 papers published in the last decade - Compares the behavior and failure modes between Geopolymer Concrete (GPC) structures and Ordinary Portland Concrete (OPC) structures - Explains important concepts such as bond, confinement, fracture of stirrups and buckling of FRP bars - Includes an in-depth analysis of ultimate strength of GPC and OPC, considering governing failure modes - Presents design examples following international standards, including North America ACI 440.1R-15, Canadian CAN/CSA S806, and Australian such as AS 3600
Download or read book Machine Design written by Andrew D. Dimarogonas and published by John Wiley & Sons. This book was released on 2000-12-18 with total page 1024 pages. Available in PDF, EPUB and Kindle. Book excerpt: Computer aided design (CAD) emerged in the 1960s out of the growing acceptance of the use of the computer as a design tool for complex systems. As computers have become faster and less expensive while handling an increasing amount of information, their use in machine design has spread from large industrial needs to the small designer.
Download or read book The Static and Dynamic Properties of Steel written by American Vanadium Co and published by . This book was released on 1911 with total page 15 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Metal Deformation Processing written by F. W. Boulger and published by . This book was released on 1964 with total page 182 pages. Available in PDF, EPUB and Kindle. Book excerpt: As part of the Metalworking Process and Equipment Program, a survey was conducted to collect and summarize information on deformation characteristics of metals and their effect on processing operations. This report presents information obtained from reports on Governmentsponsored work and from articles in technical publications. The report covers eight subjects: extrusion, forging, rolling, thermal mechanical variables affecting the properties of refractory metals and alloys, development of preferred orientations, anisotropy of strength and ductility, high-strain-rate deformation, and strain aging. In order to be useful to engineering students and production engineers the topics are treated in two ways. Generalized discussions of common processes point out why specific variables must be modified in order to deform certain types of metals satisfactorily. When practical, data on the more-difficultto-form metals are used to illustrate the principles, limitations, and effects of the processes. The objective is to help the non-specialist recognize the implications of specific findings and to apply them to specific operations. (Author).
