Download or read book Dust Studies in DIII D and TEXTOR written by and published by . This book was released on 2008 with total page 10 pages. Available in PDF, EPUB and Kindle. Book excerpt: Studies of naturally occurring and artificially introduced carbon dust are conducted in DIII-D and TEXTOR. In DIII-D, dust does not present operational concerns except immediately after entry vents. Energetic plasma disruptions produce significant amounts of dust. However, dust production by disruptions alone is insufficient to account for the estimated in-vessel dust inventory in DIII-D. Submicron sized dust is routinely observed using Mie scattering from a Nd:Yag laser. The source is strongly correlated with the presence of Type I edge localized modes (ELMs). Larger size (0.005-1 mm diameter) dust is observed by optical imaging, showing elevated dust levels after entry vents. Inverse dependence of the dust velocity on the inferred dust size is found from the imaging data. Migration of pre-characterized carbon dust is studied in DIII-D and TEXTOR by injecting micron-size dust in plasma discharges. In DIII-D, a sample holder filled with (almost equal to)30 mg of dust is introduced in the lower divertor and exposed to high-power ELMing H-mode discharges with strike points swept across the divertor floor. After a brief exposure ((almost equal to)0.1 s) at the outer strike point, part of the dust is injected into the plasma, raising the core carbon density by a factor of 2-3 and resulting in a twofold increase of the radiated power. Individual dust particles are observed moving at velocities of 10-100 m/s, predominantly in the toroidal direction, consistent with the drag force from the deuteron flow and in agreement with modeling by the 3D DustT code. In TEXTOR, instrumented dust holders with 1-45 mg of dust are exposed in the scrape-off layer 0-2 cm radially outside of the last closed flux surface in discharges heated with neutral beam injection (NBI) power of 1.4 MW. Dust is launched either in the beginning of a discharge or at the initiation of NBI, preferentially in a direction perpendicular to the toroidal magnetic field. At the given configuration of the launch, the dust did not penetrate the core plasma and only moderately perturbed the edge plasma, as evidenced by an increase of the edge carbon content.
Download or read book On the Edge of Magnetic Fusion Devices written by Sergei Krasheninnikov and published by Springer Nature. This book was released on 2020-09-07 with total page 269 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book reviews the current state of understanding concerning edge plasma, which bridges hot fusion plasma, with a temperature of roughly one million degrees Kelvin with plasma-facing materials, which have melting points of only a few thousand degrees Kelvin. In a fact, edge plasma is one of the keys to solution for harnessing fusion energy in magnetic fusion devices. The physics governing the processes at work in the edge plasma involves classical and anomalous transport of multispecies plasma, neutral gas dynamics, atomic physics effects, radiation transport, plasma-material interactions, and even the transport of plasma species within the plasma-facing materials. The book starts with simple physical models, then moves on to rigorous theoretical considerations and state-of-the-art simulation tools that are capable of capturing the most important features of the edge plasma phenomena. The authors compare the conclusions arising from the theoretical and computational analysis with the available experimental data. They also discuss the remaining gaps in their models and make projections for phenomena related to edge plasma in magnetic fusion reactors.
Download or read book DIII D Dust Particulate Characterization June 1998 Vent written by and published by . This book was released on 1999 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Dust is a key component of fusion power device accident source term. Understanding the amount of dust expected in fusion power devices and its physical and chemical characteristics is needed to verify assumptions currently used in safety analyses. An important part of this safety research and development work is to characterize dust from existing experimental tokamaks. In this report, we present the collection, data analysis methods used, and the characterization of dust particulate collected from various locations inside the General Atomics DIII-D vacuum vessel following the June 1998 vent. The collected particulate was analyzed at the Idaho National Engineering and Environmental Laboratory (INEEL). Two methods were used to collect particulate with the goal of preserving the particle size distribution and physical characteristics of the particulate. Choice of collection technique is important because the sampling method used can bias the particle size distribution collected. Vacuum collection on substrates and adhesion removal with metallurgical replicating tape were chosen as non-intrusive sampling methods. Seventeen samples were collected including plasma facing surfaces in lower, upper, and horizontal locations, surfaces behind floor tiles, surfaces behind divertor tiles, and surfaces behind ceiling tiles. The results of the analysis are presented.
Download or read book Introduction to Dusty Plasma Physics written by P.K Shukla and published by CRC Press. This book was released on 2015-05-06 with total page 281 pages. Available in PDF, EPUB and Kindle. Book excerpt: Introduction to Dusty Plasma Physics contains a detailed description of the occurrence of dusty plasmas in our Solar System, the Earth's mesosphere, and in laboratory discharges. The book illustrates numerous mechanisms for charging dust particles and provides studies of the grain dynamics under the influence of forces that are common in dusty plas
Download or read book Techniques For Injection Of Pre Charaterized Dust Into The Scrape Off Layer Of Fusion Plasma written by and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Introduction of micron-sized dust into the scrape-off layer (SOL) of a plasma has recently found many applications aimed primarily at determining dust behavior in future fusion reactors. The dust particles are typically composed of materials intrinsic to a fusion reactor. On DIII-D and TEXTOR carbon dust has been introduced into the SOL using a probe inserted from below into the divertor region. On NSTX, both Li and tungsten dust have been dropped from the top of the machine into the SOL throughout the duration of a discharge, by utilizing a vibrating piezoelectric based particle dropper. The original particle dropper was developed to inject passivated Li powder ≈ 40 [mu]m in diameter into the SOL to enhance plasma performance. A simplified version of the dropper was developed to introduce trace amounts of tungsten powder for only a few discharges, thus not requiring a large powder reservoir. The particles emit visible light from plasma interactions and can be tracked by either spectroscopic means or by fast frame rate visible cameras. This data can then be compared with dust transport codes such as DUSTT to make predictions of dust behavior in next-step devices such as ITER. For complete modeling results, it is desired to be able to inject pre-characterized dust particles in the SOL at various known poloidal locations, including near the vessel midplane. Purely mechanical methods of injecting particles are presently being studied using a modified piezoelectric-based powder dropper as a particle source and one of several piezo-based transducers to deflect the particles into the SOL. Vibrating piezo fans operating at 60 Hz with a deflection of ±2.5 cm can impart a significant horizontal boost in velocity. The highest injection velocities are expected from rotating paddle wheels capable of injecting particles at 10's of meters per second depending primarily on the rotation velocity and diameter of the wheel. Several injection concepts have been tested and will be discussed below.
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1995 with total page 704 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Plasma Material Interactions in a Controlled Fusion Reactor written by Tetsuo Tanabe and published by Springer Nature. This book was released on 2021-03-08 with total page 209 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is a primer on the interplay between plasma and materials in a fusion reactor, so-called plasma–materials interactions (PMIs), highlighting materials and their influence on plasma through PMI. It aims to demonstrate that a plasma-facing surface (PFS) responds actively to fusion plasma and that the clarifying nature of PFS is indispensable to understanding the influence of PFS on plasma. It describes the modern insight into PMI, namely, relevant feedback to plasma performance from plasma-facing material (PFM) on changes in a material surface by plasma power load by radiation and particles, contrary to a conventional view that unilateral influence from plasma on PFM is dominant in PMI. There are many books and reviews on PMI in the context of plasma physics, that is, how plasma or plasma confinement works in PMI. By contrast, this book features a materials aspect in PMI focusing on changes caused by heat and particle load from plasma: how PFMs are changed by plasma exposure and then, accordingly, how the changed PFM interacts with plasma.
Download or read book New Aspects of Plasma Physics written by Bengt Eliasson and published by World Scientific. This book was released on 2008 with total page 513 pages. Available in PDF, EPUB and Kindle. Book excerpt: The OC 2007 ICTP Summer College on Plasma Physics'' was held at the Abdus Salam International Centre for Theoretical Physics (ICTP), Trieste, Italy, during the period 30 July to 24 August 2007. The purpose of the summer college was to provide training for young scientists from all over the world, mainly from third world countries, and to give them the opportunity to interact with senior scientists in an informal manner. A large number of talks were given by invited speakers and experts, with information about the most recent advances in magnetic confinement fusion and tokamak physics, intense laserOCoplasma interactions and plasma-based particle acceleration, turbulence, dusty plasmas, and the emerging field of quantum plasmas. A selected number of papers from the invited speakers appear in this book. Sample Chapter(s). Foreword (60 KB). Nonlinear Collective Processes in Very Dense Plasmas (1,782 KB). Contents: Nonlinear Collective Processes in Very Dense Plasmas (P K Shukla et al.); Quantum, Spin and QED Effects in Plasmas (G Brodin & M Marklund); Quantum Methodologies in Beam, Fluid and Plasma Physics (R Fedele); Generation of Galactic Seed Magnetic Fields (H Saleem); Multifluid Theory of Solitons (F Verheest); Electro-Acoustic Solitary Waves in Dusty Plasmas (A A Mamun & P K Shukla); Physics of Dust in Magnetic Fusion Devices (Z Wang et al.); Short Wavelength Ballooning Mode in Tokamaks (A Hirose & N Joiner); and other papers. Readership: Researchers in the field of plasma physics."
Download or read book Fusion Science and Technology written by and published by . This book was released on 2008 with total page 808 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Energy Research Abstracts written by and published by . This book was released on 1993 with total page 900 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Plasma Surface Interactions in Controlled Fusion Devices written by and published by . This book was released on 1978 with total page 658 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Arid Zone Geomorphology written by David S. G. Thomas and published by John Wiley & Sons. This book was released on 2011-02-08 with total page 658 pages. Available in PDF, EPUB and Kindle. Book excerpt: The new edition of Arid Zone Geomorphology aims to encapsulate the advances that have been made in recent years in the investigation and explanation of landforms and geomorphological processes in drylands. Building on the success of the previous two editions, the Third Edition has been completely revised and updated to reflect the latest developments in the field. Whilst this latest edition will remain a comprehensive reference to the subject, the book has been restructured to include regional case studies throughout to enhance student understanding and is clearly defined into five distinct sections; Firstly, the book introduces the reader to Large Scale Controls and Variability in Drylands and then moves on to consider Surface Processes and Characteristics; The Work of Water, The Work of the Wind. The book concludes with a section on Living with Dryland Geomorphology that includes a chapter on geomorphological hazards and the human impact on these environments. Once again, recognised world experts in the field have been invited to contribute chapters in order to present a comprehensive and up-to-date overview of current knowledge about the processes shaping the landscape of deserts and arid regions. In order to broaden the appeal of the Third Edition, the book has been reduced in extent by 100 pages and the Regional chapters have been omitted in favour of the inclusion of key regional case studies throughout the book. The Editor is also considering the inclusion of a supplementary website that could include further images, problems and case studies.
Download or read book Metals Abstracts written by and published by . This book was released on 1996 with total page 1628 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Applied Magnetism written by R. Gerber and published by Springer Science & Business Media. This book was released on 2013-03-09 with total page 596 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is based on the contributions to a course, entitled Applied Magnetism, which was the 25th Course of the International School of Materials Science and Technology. The Course was held as a NATO Advanced Study Institute at the Ettore Majorana Centre in Erice, Sicily, Italy between the 1st and 12th July 1992, and attracted almost 70 participants from 15 different countries. The book deals with the theory, experiments and applications of the main topical areas of applied magnetism. These selected areas include the physics of magnetic recording, magnetic and magneto-optic recording devices, systems and media, magnetic fine particles, magnetic separation, domains and domain walls in soft magnetic materials, permanent magnets, magnetoresistance, thin film magneto-optics, and finally, microwave, optical and computational magnetics. The material is organised into I 0 self-contained chapters which together provide a comprehensive coverage of the subject of applied magnetism. The aim is to emphasise the connection between the fundamental theoretical concepts, key experiments and the important technological developments which have been achieved in this field up to the present time. Moreover, when and where possible, pointers to future trends are indicated which hopefully, together with the background material, will promote further advancement of research. The organizing committee would like to acknowledge the sponsorship of the NATO Scientific Affairs Division, the National Science Foundation of the USA, the Science and Engineering Research Council of the UK, the Italian Ministry of Education, the Italian Ministry of University and Scientific Research and the Sicilian Regional Government.
Download or read book Metals Abstracts Index written by and published by . This book was released on 1996 with total page 1622 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Encyclopedia of Plasma Technology Two Volume Set written by J. Leon Shohet and published by CRC Press. This book was released on 2016-12-12 with total page 1654 pages. Available in PDF, EPUB and Kindle. Book excerpt: Technical plasmas have a wide range of industrial applications. The Encyclopedia of Plasma Technology covers all aspects of plasma technology from the fundamentals to a range of applications across a large number of industries and disciplines. Topics covered include nanotechnology, solar cell technology, biomedical and clinical applications, electronic materials, sustainability, and clean technologies. The book bridges materials science, industrial chemistry, physics, and engineering, making it a must have for researchers in industry and academia, as well as those working on application-oriented plasma technologies. Also Available Online This Taylor & Francis encyclopedia is also available through online subscription, offering a variety of extra benefits for researchers, students, and librarians, including: Citation tracking and alerts Active reference linking Saved searches and marked lists HTML and PDF format options Contact Taylor and Francis for more information or to inquire about subscription options and print/online combination packages. US: (Tel) 1.888.318.2367; (E-mail) [email protected] International: (Tel) +44 (0) 20 7017 6062; (E-mail) [email protected]
Download or read book Mineral Dust written by Peter Knippertz and published by Springer. This book was released on 2014-09-01 with total page 526 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume presents state-of-the-art research about mineral dust, including results from field campaigns, satellite observations, laboratory studies, computer modelling and theoretical studies. Dust research is a new, dynamic and fast-growing area of science and due to its multiple roles in the Earth system, dust has become a fascinating topic for many scientific disciplines. Aspects of dust research covered in this book reach from timescales of minutes (as with dust devils, cloud processes and radiation) to millennia (as with loess formation and oceanic sediments), making dust both a player and recorder of environmental change. The book is structured in four main parts that explore characteristics of dust, the global dust cycle, impacts of dust on the Earth system, and dust as a climate indicator. The chapters in these parts provide a comprehensive, detailed overview of this highly interdisciplinary subject. The contributions presented here cover dust from source to sink and describe all the processes dust particles undergo while travelling through the atmosphere. Chapters explore how dust is lifted and transported, how it affects radiation, clouds, regional circulations, precipitation and chemical processes in the atmosphere and how it deteriorates air quality. The book explores how dust is removed from the atmosphere by gravitational settling, turbulence or precipitation, how iron contained in dust fertilizes terrestrial and marine ecosystems, and about the role that dust plays in human health. We learn how dust is observed, simulated using computer models and forecast. The book also details the role of dust deposits for climate reconstructions. Scientific observations and results are presented, along with numerous illustrations. This work has an interdisciplinary appeal and will engage scholars in geology, geography, chemistry, meteorology and physics, amongst others with an interest in the Earth system and environmental change. body>
