Download or read book Drinking Water Softening scale Prevention Technology Assessment and Performance of Template Assisted Crystallization written by Lin Shen and published by . This book was released on 2019 with total page 126 pages. Available in PDF, EPUB and Kindle. Book excerpt: Hard water typically has a hardness concentration over 120 mg/L CaCO3. Hardness is not a regulated drinking water parameter and does not have severe health effects. However, hard water causes more soap and detergent consumption and can cause scaling problems on household heating appliances, distribution pipes, and industrial cooling equipment. There are various approaches to soften hard water or prevent scale formation at the centralized and the household scale. In order to choose the best treatment for a specific set of conditions, an appropriate technology evaluation is necessary. Prior research have tested single technology or compared two or three technologies with respect to their performance. Not many papers have compared all available technologies using the same assessment criteria. At the household scale, point-of-entry (POE) devices are commonly used. Among these, ion exchange is the most widely applied POE device in Canada, though it has two major disadvantages: high sodium concentration in softened water and high chloride content in the brine which is often discharged into the sewer. Hence, there is an increasing interest in adopting salt-free treatment technology. Template assisted crystallization (TAC) is a relatively new household scale prevention technology. TAC media transforms free calcium (Ca2+) and magnesium (Mg2+) ions into insoluble microcrystals. TAC technology has the potential to be an alternative to ion exchange, but there is very little published journals about this technology. Therefore, this study had two objectives: 1) to assess and rank currently available softening and scale prevention technologies at both the centralized and household level, and 2) test the performance of the TAC technology using two source waters. The multi-criteria assessment (MCA) method was utilized to evaluate centralized technologies (lime softening, pellet softening, nanofiltration, and ion exchange) as well as household technologies (TAC, ion exchange, nanofiltration, electrically induced precipitation, magnetic water treatment, and capacitive deionization). Criteria that were chosen in this assessment were: waste disposal, energy requirement, life-cycle cost, efficiency, subsequent treatment needed for finished water, chemical addition, easy to use, and validated technology. The initial assessment assigned a higher weight to the first four criteria listed. A sensitivity analysis (SA) was done by changing the weight assignment of different criteria. Three cases were selected: more focus on waste disposal and energy requirement; more emphasis on cost; iv each criterion shared equal importance. For the centralized technologies assessment, pellet softening had the highest score, followed by ion exchange, lime softening, and nanofiltration. SA results showed that although the total score of each technology varied, the final rank did not change. For the household technologies assessment, TAC had the highest score, followed by ion exchange, magnetic water treatment, electrically induced precipitation, nanofiltration, and capacitive deionization. SA results showed that the total score varied, but the final rank did not change. The performance of TAC technology was assessed using four tests which compared untreated and treated water samples of two selected source waters. The first test measured the reduction of free Ca2+ by a Ca2+ selective electrode after being treated by TAC in two source waters and, test results did not show a lot of reduction with percentage reductions ranging from 4.0% to 5.0% for both locations. The reductions were statistically significant but not large enough to be of much practical value. The second test was to measure the change in total Ca2+ and Mg2+ concentration after TAC. The changes were relatively small in both source waters, with percentage reductions ranging from 2.7% to 4.4% for Ca2+ and 4.0% to 6.9% for Mg2+. Again, the reductions were statistically significant but not large enough to be of much practical value. The third test was a sequential ultrafiltration test utilizing membranes (3000 Da, 1000 Da, and 500 Da) to identify the microcrystal size. This test was not able to isolate substantial amounts of microcrystal, nor did it identify the approximate microcrystal size. The last test was developed as a simplified scale test. Results showed that treated water forms somewhat less scale than untreated water for both source waters. Scale formation potential indices: Langelier Saturation Index (LSI) and Calcium Carbonate Precipitation Potential (CCPP) were also calculated, and results showed that there was essentially no change in both indices after the TAC treatment. Overall, assessment results showed that using this study's criteria, pellet softening and TAC were the two most suitable technologies to be applied at the centralized and household level, respectively. The TAC performance tests did not establish a substantial reduction in free calcium ions, nor were any crystals isolated. The scale test only showed relatively small differences between untreated and treated water. Future research could construct a flow-through system to test the performance of TAC technology and should also conduct some tests on new and used media.
Download or read book Extrusion written by Harold F. Giles Jr and published by William Andrew. This book was released on 2013-09-21 with total page 638 pages. Available in PDF, EPUB and Kindle. Book excerpt: The second edition of Extrusion is designed to aid operators, engineers, and managers in extrusion processing in quickly answering practical day-to-day questions. The first part of the book provides the fundamental principles, for operators and engineers, of polymeric materials extrusion processing in single and twin screw extruders. The next section covers advanced topics including troubleshooting, auxiliary equipment, and coextrusion for operators, engineers, and managers. The final part provides applications case studies in key areas for engineers such as compounding, blown film, extrusion blow molding, coating, foam, and reprocessing. This practical guide to extrusion brings together both equipment and materials processing aspects. It covers basic and advanced topics, for reference and training, in thermoplastics processing in the extruder. Detailed reference data are provided on such important operating conditions as temperatures, start-up procedures, shear rates, pressure drops, and safety. A practical guide to the selection, design and optimization of extrusion processes and equipment Designed to improve production efficiency and product quality Focuses on practical fault analysis and troubleshooting techniques
Download or read book Handbook of Brewing written by Hans Michael Eßlinger and published by John Wiley & Sons. This book was released on 2009-04-22 with total page 778 pages. Available in PDF, EPUB and Kindle. Book excerpt: This comprehensive reference combines the technological know-how from five centuries of industrial-scale brewing to meet the needs of a global economy. The editor and authors draw on the expertise gained in the world's most competitive beer market (Germany), where many of the current technologies were first introduced. Following a look at the history of beer brewing, the book goes on to discuss raw materials, fermentation, maturation and storage, filtration and stabilization, special production methods and beermix beverages. Further chapters investigate the properties and quality of beer, flavor stability, analysis and quality control, microbiology and certification, as well as physiology and toxicology. Such modern aspects as automation, energy and environmental protection are also considered. Regional processes and specialties are addressed throughout the entire book, making this a truly global resource on brewing.
Download or read book Historic Lighthouse Preservation Handbook written by and published by U.S. Government Printing Office. This book was released on 1997 with total page 326 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Physicochemical Treatment Processes written by Lawrence K. Wang and published by Springer Science & Business Media. This book was released on 2005-03-11 with total page 731 pages. Available in PDF, EPUB and Kindle. Book excerpt: The past 30 years have seen the emergence of a growing desire worldwide to take positive actions to restore and protect the environment from the degrading effects of all forms of pollution: air, noise, solid waste, and water. Because pollution is a direct or indirect consequence of waste, the seemingly idealistic demand for “zero discharge” can be construed as an unrealistic demand for zero waste. However, as long as waste exists, we can only attempt to abate the subsequent pollution by converting it to a less noxious form. Three major questions usually arise when a particular type of pollution has been identified: (1) How serious is the pollution? (2) Is the technology to abate it available? and (3) Do the costs of abatement justify the degree of abatement achieved? The principal intention of the Handbook of Environmental Engineering series is to help readers formulate answers to the last two questions. The traditional approach of applying tried-and-true solutions to specific pollution pr- lems has been a major contributing factor to the success of environmental engineering, and has accounted in large measure for the establishment of a “methodology of pollution c- trol. ” However, realization of the ever-increasing complexity and interrelated nature of current environmental problems makes it imperative that intelligent planning of pollution abatement systems be undertaken.
Download or read book Protecting Groundwater for Health written by World Health Organization and published by World Health Organization. This book was released on 2006 with total page 697 pages. Available in PDF, EPUB and Kindle. Book excerpt: This publication provides a structured approach to analyzing hazards to groundwater quality, assessing the risk they may cause for a specific supply, setting priorities in addressing these, and developing management strategies for their control. This book summarizes which pathogens and chemicals are relevant to human health, how they are transported, reduced, removed or retarded; provides practical guidance on characterizing the drinking-water catchment area and assessing potential health hazards; provides guidance on prioritising both hazards and management responses; presents key information on potential management actions and explains their integration into a comprehensive Water Safety Plan from catchment to consumer; and describes policy, land-use planning and implementation of pollution prevention, groundwater, with overviews of specific management approaches applicable to agriculture, sanitation, industry, mining, military sites, waste disposal and traffic.--Publisher's description.
Download or read book New Technologies for Seawater Desalination Using Nuclear Energy written by and published by . This book was released on 2015-03-11 with total page 171 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Pharmaceutical Manufacturing Handbook written by Shayne Cox Gad and published by John Wiley & Sons. This book was released on 2008-03-21 with total page 1384 pages. Available in PDF, EPUB and Kindle. Book excerpt: This handbook features contributions from a team of expert authors representing the many disciplines within science, engineering, and technology that are involved in pharmaceutical manufacturing. They provide the information and tools you need to design, implement, operate, and troubleshoot a pharmaceutical manufacturing system. The editor, with more than thirty years' experience working with pharmaceutical and biotechnology companies, carefully reviewed all the chapters to ensure that each one is thorough, accurate, and clear.
Download or read book The Aggregates Handbook Second Edition written by National Stone, Sand & Gravel Association and published by . This book was released on 2013-03-20 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Medical Surgical Nursing written by Sharon Mantik Lewis and published by Mosby Incorporated. This book was released on 2003-12-01 with total page 2176 pages. Available in PDF, EPUB and Kindle. Book excerpt: Package includes Medical-Surgical Nursing: Assessment and Management of Clinical Problems Two Volume text and Virtual Clinical Excursions 2.0
Download or read book Medicines from Animal Cell Culture written by Glyn N. Stacey and published by John Wiley & Sons. This book was released on 2007-06-29 with total page 696 pages. Available in PDF, EPUB and Kindle. Book excerpt: Medicines from Animal Cell Culture focuses on the use of animal cell culture, which has been used to produce human and veterinary vaccines, interferon, monoclonal antibodies and genetically engineered products such as tPA and erythropoietin. It also addresses the recent dramatic expansion in cell-based therapies, including the use of live cells for tissue regeneration and the culture of stem cells. Medicines from Animal Cell Culture: Provides comprehensive descriptions of methods for cell culture and nutrition as well as the technologies for the preservation and characterisation of both the cells and the derived products Describes the preparation of stem cells and others for use in cell-based therapies – an area of burgeoning research Includes experimental examples to indicate expected results Covers regulatory issues from the UK, the EU and the USA and reviews how these are developing around the world Addresses the key issues of standardisation and validation with chapters on GLP and GMP for cell culture processes Delivering insight into the exciting world of biological medicines and directions for further investigation into specific topics, Medicines from Animal Cell Culture is an essential resource for researchers and technicians at all levels using cell culture within the pharmaceutical, biotechnology and biomedical industries. It is of value to laboratory managers in these industries and to all those interested in this topic alike.
Download or read book Perovskite Photovoltaics written by Aparna Thankappan and published by Academic Press. This book was released on 2018-06-29 with total page 521 pages. Available in PDF, EPUB and Kindle. Book excerpt: Perovskite Photovoltaics: Basic to Advanced Concepts and Implementation examines the emergence of perovskite photovoltaics, associated challenges and opportunities, and how to achieve broader development. Consolidating developments in perovskite photovoltaics, including recent progress solar cells, this text also highlights advances and the research necessary for sustaining energy. Addressing different photovoltaics fields with tailored content for what makes perovskite solar cells suitable, and including commercialization examples of large-scale perovskite solar technology. The book also contains a detailed analysis of the implementation and economic viability of perovskite solar cells, highlighting what photovoltaic devices need to be generated by low cost, non-toxic, earth abundant materials using environmentally scalable processes. This book is a valuable resource engineers, scientists and researchers, and all those who wish to broaden their knowledge on flexible perovskite solar cells. Includes contributions by leading solar cell academics, industrialists, researchers and institutions across the globe Addresses different photovoltaics fields with tailored content for what makes perovskite solar cells different Provides commercialization examples of large-scale perovskite solar technology, giving users detailed analysis on the implementation, technical challenges and economic viability of perovskite solar cells
Download or read book Membrane and Desalination Technologies written by Lawrence K. Wang and published by Springer Science & Business Media. This book was released on 2010-12-01 with total page 728 pages. Available in PDF, EPUB and Kindle. Book excerpt: In this essential new volume, Volume 13: Membrane and Desalination Technologies, a panel of expert researchers provide a wealth of information on membrane and desalination technologies. An advanced chemical and environmental engineering textbook as well as a comprehensive reference book, this volume is of high value to advanced graduate and undergraduate students, researchers, scientists, and designers of water and wastewater treatment systems. This is an essential part of the Handbook of Environmental Engineering series, an incredible collection of methodologies that study the effects of pollution and waste in their three basic forms: gas, solid, and liquid. Chapters adopt the series format, employing methods of practical design and calculation illustrated by numerical examples, including pertinent cost data whenever possible, and exploring in great detail the fundamental principles of the field. Volume 13: Membrane and Desalination Technologies is an essential guide for researchers, highlighting the latest developments in principles of membrane technology, membrane systems planning and design, industrial and municipal waste treatments, desalination requirements, wastewater reclamation, biofiltration, and more.
Download or read book Reflow Soldering Processes written by Ning-Cheng Lee and published by Newnes. This book was released on 2002-01-11 with total page 282 pages. Available in PDF, EPUB and Kindle. Book excerpt: Focused on technological innovations in the field of electronics packaging and production, this book elucidates the changes in reflow soldering processes, its impact on defect mechanisms, and, accordingly, the troubleshooting techniques during these processes in a variety of board types. Geared toward electronics manufacturing process engineers, design engineers, as well as students in process engineering classes, Reflow Soldering Processes and Troubleshooting will be a strong contender in the continuing skill development market for manufacturing personnel. Written using a very practical, hands-on approach, Reflow Soldering Processes and Troubleshooting provides the means for engineers to increase their understanding of the principles of soldering, flux, and solder paste technology. The author facilitates learning about other essential topics, such as area array packages--including BGA, CSP, and FC designs, bumping technique, assembly, and rework process,--and provides an increased understanding of the reliability failure modes of soldered SMT components. With cost effectiveness foremost in mind, this book is designed to troubleshoot errors or problems before boards go into the manufacturing process, saving time and money on the front end. The author's vast expertise and knowledge ensure that coverage of topics is expertly researched, written, and organized to best meet the needs of manufacturing process engineers, students, practitioners, and anyone with a desire to learn more about reflow soldering processes. Comprehensive and indispensable, this book will prove a perfect training and reference tool that readers will find invaluable. Provides engineers the cutting-edge technology in a rapidly changing field Offers in-depth coverage of the principles of soldering, flux, solder paste technology, area array packages--including BGA, CSP, and FC designs, bumping technique, assembly, and the rework process
Download or read book Zeolite Synthesis written by Mario L. Occelli and published by . This book was released on 1989 with total page 672 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume is a complete progress report on the various aspects of zeolite synthesis on a molecular level. It provides many examples that illustrate how zeolites can be crystallized and what the important parameters are that control crystallization. Forty-two chapters cover such topics as: crystallization techniques; gel chemistry; crystal size and morphology; the role of organic compounds; and novel synthesis procedures. It offers a complete review of zeolite synthesis as well as the latest finding in this important field. Contains benchmark contributions from many notable pioneers in the field, including R.M. Barrer, H. Robson, and Robert Milton.
Download or read book Guide to ASTM Test Methods for the Analysis of Petroleum Products and Lubricants written by R. A. Nadkarni and published by Astm International. This book was released on 2000 with total page 389 pages. Available in PDF, EPUB and Kindle. Book excerpt: Summarizes the essential elements of all analytical tests used to characterize petroleum products. The 350 plus entries are alphabetically arranged by chemical and physical properties, such as apparent viscosity, density, metal analysis, sulfur determination, vapor pressure, and water. Each entry co
Download or read book Introduction to Environmental Engineering with Unit Conversion Booklet written by Mackenzie L. Davis and published by McGraw-Hill Science, Engineering & Mathematics. This book was released on 1998 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This comprehensive new edition tackles the multiple aspects of environmental engineering, from solid waste disposal to air and noise pollution. It places a much-needed emphasis on fundamental concepts, definitions, and problem-solving while providing updated problems and discussion questions in each chapter. Introduction to Environmental Engineering also includes a discussion of environmental legislation along with environmental ethics case studies and problems to present the legal framework that governs environmental engineering design.
