Download or read book Dimensional Specifications for Metallic Body Push to Connect Fittings Used on a Vehicular Air Brake System written by Air Brake Tubing and Tube Ftg Committee and published by . This book was released on 2011 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard covers general and dimensional specifications for brass bodied reusable Push to Connect tube fittings for use in the piping of vehicular air brake systems. This type of fitting is intended for use with nylon tubing per SAE J844. See SAE J2494-3 for the Performance Requirements of Reusable (Push to Connect) Fittings Intended for Use in Automotive Air Brake Systems and U.S. Department of Transportation, National Highway Traffic Safety Administration (NHTSA) Federal Motor Vehicle Safety Standards (FMVSS) 571. The purpose of the changes noted in this document are to harmonize the dimensioning scheme for the jam nut thickness of bulkhead unions found in Figure 1 with that of Figure 2 in this document and also Figure A5 of SAE J2494-2. In each case, the bulkhead union jam nut thickness dimensions was noted to be a "minimum", except for that found in Table 1A and 1B for Figure 1 of SAE J2494-1 where the dimensions were noted to be a "maximum". It is reasonable that the dimensions for the jam nut thickness, define a certain minimum thickness, as to insure an adequate thread engagement will be maintained for the integrity of the fitting. Correcting Table 1A and 1B, harmonizes the design intent for all bulkhead union, jam nut minimum thickness found in the SAE J2494-1 and SAE J2494-2 documents.

Download or read book Dimensional Specifications for Metallic Body Push To Connect Fittings Used on a Vehicle Air Brake System written by Air Brake Tubing and Tube Ftg Committee and published by . This book was released on 2004 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard covers general and dimensional specifications for brass bodied reusable Push-to-Connect tube fittings for use in the piping of vehicular air brake systems. This type of fitting is intended for use with nylon tubing per SAE J844. Performance requirements for SAE J844 are covered in SAE J1131. See SAE J1131 for the Performance Requirements of Reusable (Push-to-Connect) Fittings Intended for Use in Automotive Air Brake Systems and U.S. Department of Transportation FMVSS 571.

Download or read book Dimensional Specifications for Non Metallic Body Push to Connect Fittings Used On a Vehicular Air Brake System written by Air Brake Tubing and Tube Ftg Committee and published by . This book was released on 2002 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard covers general dimensional specifications for non-metallic body reusable push to connect tube fittings for use in the piping of air brake systems on automotive vehicles. This type of fitting is intended for use with nylon tubing per SAE J844. It is not intended to restrict or preclude other designs of a tube fitting for use with SAE J844. Performance requirements for SAE J844 are covered in SAE J1131. See SAE J2494-3 for the performance requirements of Reusable (push-to-connect) fittings intended for use in Automotive Air Brake Systems and U.S. Department of Transportation FMVSS 571.106.

Download or read book Federal Register written by and published by . This book was released on 2007-10 with total page 308 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book AUTOMOTIVE TUBE FITTINGS written by Air Brake Tubing and Tube Ftg Committee and published by . This book was released on 1996 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard covers complete general and dimensional specifications for the various types of tube fittings intended for general application in the automotive, appliance, and allied fields. See SAE J1131 for the performance requirements of reusable (push to connect) fittings intended for use in automotive air brake systems.Flare type fittings shall be as specified in Figures 1 to 4 and Tables 3 to 5. Inverted flared type fittings shall be as specified in Figures 5 to 11 and Tables 3, 6, 7, 8, and 9. Gages and gaging procedures pertaining to inverted flared tube fittings are given in Appendix A. Tapered sleeve compression type fittings intended for general use with annealed copper alloy tubings shall be as specified in Figures 12 to 17 and Tables 3, 10, 11, and 12. To assure satisfactory performance, spherical sleeve compression type fitting components (see SAE J246) should not be intermixed with tapered sleeve compression type fitting components when assembling connections in areas where both types are available.Dimensions of single and double 45 degree flares on tubing to be used in conjunction with flared and inverted flared fittings are given in Figure 2 and Table 3 of SAE J533.The following general specifications supplement the dimensional data for all types of fittings contained in Tables 3 to 13 with respect to all unspecified detail.

Download or read book Spherical and Flanged Sleeve Compression Tube Fittings written by Air Brake Tubing and Tube Ftg Committee and published by . This book was released on 2017 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard covers complete general and dimensional specifications for tube fittings of the spherical and flanged sleeve compression types for use in the piping of air brake systems on automotive vehicles. The spherical sleeve compression type Figures 1A to 5 and Tables 1 to 3 is intended for use with annealed copper alloy tubing per SAE J1149, Type 1. The flanged sleeve compression type Figures 6A to 11 and Tables 4 to 6 is intended for use with nylon tubing per SAE J844. It is not intended to restrict or preclude other designs of a tube fitting for use with SAE J844, air brake tubing. Performance requirements for SAE J844 are covered in SAE J1131. See SAE J1131 for the Performance Requirements of Reusable (Push to Connect) Fittings Intended for Use in Automotive Air Brake Systems.CAUTION: To assure satisfactory performance, tapered sleeve compression type fitting components (SAE J512) should not be intermixed with the spherical or flanged sleeve components, nor should the spherical sleeve compression type components be intermixed with the flanged sleeve compression type components when assembling connection in areas where the three types are available. J246 has been reaffirmed to comply with the SAE Five-Year Review policy.

Download or read book Spherical and Flanged Sleeve Compression Tube Fittings written by Hydraulic Tube Fittings Committee and published by . This book was released on 1997 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard covers complete general and dimensional specifications for tube fittings of the spherical and flanged sleeve compression types for use in the piping of air brake systems on automotive vehicles. The spherical sleeve compression type Figures 1A to 5 and Tables 1 to 3 is intended for use with annealed copper alloy tubing per SAE J1149, Type 1. The flanged sleeve compression type Figures 6A to 11 and Tables 4 to 6 is intended for use with nylon tubing per SAE J844. It is not intended to restrict or preclude other designs of a tube fitting for use with SAE J844, air brake tubing. Performance requirements for SAE J844 are covered in J1131. See SAE J1131 for the Performance Requirements of Reusable (Push to Connect) Fittings Intended for use in Automotive Air Brake Systems. CAUTION: To assure satisfactory performance, tapered sleeve compression type fitting components (SAE J512) should not be intermixed with the spherical or flanged sleeve components, nor should the spherical sleeve compression type components be intermixed with the flanged sleeve compression type components when assembling connection in areas where the three types are available.

Download or read book Automotive Pipe Fittings written by Air Brake Tubing and Tube Ftg Committee and published by . This book was released on 2018 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard includes complete general and dimensional specifications for those types of pipe fittings commonly used in the automotive and other mass production industries where the use of lubricants or sealers is objectionable. The automotive pipe fittings shown in Figures 1 to 17 and Tables 1 to 6 are intended for general automotive and similar applications involving low or medium pressures or in conjunction with automotive tube fittings in piping systems.

Download or read book Standard Specification for Metallic Press Connect Fittings for Piping and Tubing Systems written by and published by . This book was released on with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Push to Connect Tube Fittings for Use in the Piping of Vehicular Air Brake written by and published by . This book was released on 2000 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book HOSE PUSH ON FITTINGS written by Hydraulic Hose and Hose Fittings Committee and published by . This book was released on 1978 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This standard covers complete general and dimensional specifications for hose push-on fittings. These fittings are intended for general applications in low pressure automotive and hydraulic systems on automotive, industrial, and commercial products. The fittings shown in Figs. 13 and Table 2 are intended for use with low pressure hose and shall be retained by hose clamps as specified in SAE J536.

Download or read book Specification for Dimensions of Hydraulic Connectors and Adaptors written by British Standards Institute Staff and published by . This book was released on 1997-03-15 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt: Hydraulic equipment, Hydraulic transmission systems, Hose connectors, Pipe connections, Pipe fittings, Screwed fittings, Dimensions, Interchangeability, Elbows (pipes), Bend couplings, Straight couplings, Pipe tees, Nipples (pipes), Toroidal sealing rings, Designations, Service pressure, Pressure pipes, Marking, Pressure, Dimensional tolerances

Download or read book Dictionary of Occupational Titles written by and published by . This book was released on 1991 with total page 900 pages. Available in PDF, EPUB and Kindle. Book excerpt: Supplement to 3d ed. called Selected characteristics of occupations (physical demands, working conditions, training time) issued by Bureau of Employment Security.

Download or read book Automotive Pipe Filler and Drain Plugs written by Air Brake Tubing and Tube Ftg Committee and published by . This book was released on 1992 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard includes complete general and dimensional specifications for those types of pipe, filler, and drain plugs (shown in Figures 1 to 6 and Tables 1 to 4) commonly used in automotive and related industrial applications.

Download or read book Dictionary of Occupational Titles written by United States Employment Service and published by . This book was released on 1977 with total page 1434 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Specification for Flanges and Bolting for Pipes Valves and Fittings written by British Standards Institute Staff and published by . This book was released on 1962-12-17 with total page 66 pages. Available in PDF, EPUB and Kindle. Book excerpt: Flanges, Flanged fittings, Bolting, Pipes, Pipe fittings, Valves, Unalloyed steels, Alloy steels, Steels, Cast-iron, Copper alloys, Chemical composition, Tensile strength, Elongation, Dimensions, Ratings, Temperature, Pressure, Pressure pipes

Download or read book Specification for Coupling Dimensions for Low Pressure Air Connections for Engine Starting written by British Standards Institute Staff and published by . This book was released on 1973-10-31 with total page 4 pages. Available in PDF, EPUB and Kindle. Book excerpt: Aircraft components, Pipe connections, Pipe fittings, Aircraft engines, Air, Dimensions, Aircraft ground servicing, Air transport engineering, Hose connectors, Unions, Detachable unions, Starting