Download or read book Digital Timing Macromodeling for VLSI Design Verification written by Jeong-Taek Kong and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 276 pages. Available in PDF, EPUB and Kindle. Book excerpt: Digital Timing Macromodeling for VLSI Design Verification first of all provides an extensive history of the development of simulation techniques. It presents detailed discussion of the various techniques implemented in circuit, timing, fast-timing, switch-level timing, switch-level, and gate-level simulation. It also discusses mixed-mode simulation and interconnection analysis methods. The review in Chapter 2 gives an understanding of the advantages and disadvantages of the many techniques applied in modern digital macromodels. The book also presents a wide variety of techniques for performing nonlinear macromodeling of digital MOS subcircuits which address a large number of shortcomings in existing digital MOS macromodels. Specifically, the techniques address the device model detail, transistor coupling capacitance, effective channel length modulation, series transistor reduction, effective transconductance, input terminal dependence, gate parasitic capacitance, the body effect, the impact of parasitic RC-interconnects, and the effect of transmission gates. The techniques address major sources of errors in existing macromodeling techniques, which must be addressed if macromodeling is to be accepted in commercial CAD tools by chip designers. The techniques presented in Chapters 4-6 can be implemented in other macromodels, and are demonstrated using the macromodel presented in Chapter 3. The new techniques are validated over an extremely wide range of operating conditions: much wider than has been presented for previous macromodels, thus demonstrating the wide range of applicability of these techniques.

Download or read book High Performance Digital VLSI Circuit Design written by Richard X. Gu and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 322 pages. Available in PDF, EPUB and Kindle. Book excerpt: High-Performance Digital VLSI Circuit Design is the first book devoted entirely to the design of digital high-performance VLSI circuits. CMOS, BiCMOS and bipolar ciruits are covered in depth, including state-of-the-art circuit structures. Recent advances in both the computer and telecommunications industries demand high-performance VLSI digital circuits. Digital processing of signals demands high-speed circuit techniques for the GHz range. The design of such circuits represents a great challenge; one that is amplified when the power supply is scaled down to 3.3 V. Moreover, the requirements of low-power/high-performance circuits adds an extra dimension to the design of such circuits. High-Performance Digital VLSI Circuit Design is a self-contained text, introducing the subject of high-performance VLSI circuit design and explaining the speed/power tradeoffs. The first few chapters of the book discuss the necessary background material in the area of device design and device modeling, respectively. High-performance CMOS circuits are then covered, especially the new all-N-logic dynamic circuits. Propagation delay times of high-speed bipolar CML and ECL are developed analytically to give a thorough understanding of various interacting process, device and circuit parameters. High-current phenomena of bipolar devices are also addressed as these devices typically operate at maximum currents for limited device area. Different, new, high-performance BiCMOS circuits are presented and compared to their conventional counterparts. These new circuits find direct applications in the areas of high-speed adders, frequency dividers, sense amplifiers, level-shifters, input/output clock buffers and PLLs. The book concludes with a few system application examples of digital high-performance VLSI circuits. Audience: A vital reference for practicing IC designers. Can be used as a text for graduate and senior undergraduate students in the area.

Download or read book Co Synthesis of Hardware and Software for Digital Embedded Systems written by Rajesh Kumar Gupta and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 275 pages. Available in PDF, EPUB and Kindle. Book excerpt: Co-Synthesis of Hardware and Software for Digital Embedded Systems, with a Foreword written by Giovanni De Micheli, presents techniques that are useful in building complex embedded systems. These techniques provide a competitive advantage over purely hardware or software implementations of time-constrained embedded systems. Recent advances in chip-level synthesis have made it possible to synthesize application-specific circuits under strict timing constraints. This work advances the state of the art by formulating the problem of system synthesis using both application-specific as well as reprogrammable components, such as off-the-shelf processors. Timing constraints are used to determine what part of the system functionality must be delegated to dedicated application-specific hardware while the rest is delegated to software that runs on the processor. This co-synthesis of hardware and software from behavioral specifications makes it possible to realize real-time embedded systems using off-the-shelf parts and a relatively small amount of application-specific circuitry that can be mapped to semi-custom VLSI such as gate arrays. The ability to perform detailed analysis of timing performance provides the opportunity of improving the system definition by creating better phototypes. Co-Synthesis of Hardware and Software for Digital Embedded Systems is of interest to CAD researchers and developers who want to branch off into the expanding field of hardware/software co-design, as well as to digital system designers who are interested in the present power and limitations of CAD techniques and their likely evolution.

Download or read book Binary Decision Diagrams and Applications for VLSI CAD written by Shin-ichi Minato and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 151 pages. Available in PDF, EPUB and Kindle. Book excerpt: Symbolic Boolean manipulation using binary decision diagrams (BDDs) has been successfully applied to a wide variety of tasks, particularly in very large scale integration (VLSI) computer-aided design (CAD). The concept of decision graphs as an abstract representation of Boolean functions dates back to the early work by Lee and Akers. In the last ten years, BDDs have found widespread use as a concrete data structure for symbolic Boolean manipulation. With BDDs, functions can be constructed, manipulated, and compared by simple and efficient graph algorithms. Since Boolean functions can represent not just digital circuit functions, but also such mathematical domains as sets and relations, a wide variety of CAD problems can be solved using BDDs. `Binary Decision Diagrams and Applications for VLSI CAD provides valuable information for both those who are new to BDDs as well as to long time aficionados.' -from the Foreword by Randal E. Bryant. `Over the past ten years ... BDDs have attracted the attention of many researchers because of their suitability for representing Boolean functions. They are now widely used in many practical VLSI CAD systems. ... this book can serve as an introduction to BDD techniques and ... it presents several new ideas on BDDs and their applications. ... many computer scientists and engineers will be interested in this book since Boolean function manipulation is a fundamental technique not only in digital system design but also in exploring various problems in computer science.' - from the Preface by Shin-ichi Minato.

Download or read book Quick Turnaround ASIC Design in VHDL written by N. Bouden-Romdhane and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 191 pages. Available in PDF, EPUB and Kindle. Book excerpt: From the Foreword..... Modern digital signal processing applications provide a large challenge to the system designer. Algorithms are becoming increasingly complex, and yet they must be realized with tight performance constraints. Nevertheless, these DSP algorithms are often built from many constituent canonical subtasks (e.g., IIR and FIR filters, FFTs) that can be reused in other subtasks. Design is then a problem of composing these core entities into a cohesive whole to provide both the intended functionality and the required performance. In order to organize the design process, there have been two major approaches. The top-down approach starts with an abstract, concise, functional description which can be quickly generated. On the other hand, the bottom-up approach starts from a detailed low-level design where performance can be directly assessed, but where the requisite design and interface detail take a long time to generate. In this book, the authors show a way to effectively resolve this tension by retaining the high-level conciseness of VHDL while parameterizing it to get good fit to specific applications through reuse of core library components. Since they build on a pre-designed set of core elements, accurate area, speed and power estimates can be percolated to high- level design routines which explore the design space. Results are impressive, and the cost model provided will prove to be very useful. Overall, the authors have provided an up-to-date approach, doing a good job at getting performance out of high-level design. The methodology provided makes good use of extant design tools, and is realistic in terms of the industrial design process. The approach is interesting in its own right, but is also of direct utility, and it will give the existing DSP CAD tools a highly competitive alternative. The techniques described have been developed within ARPAs RASSP (Rapid Prototyping of Application Specific Signal Processors) project, and should be of great interest there, as well as to many industrial designers. Professor Jonathan Allen, Massachusetts Institute of Technology

Download or read book Logic Synthesis for Field Programmable Gate Arrays written by Rajeev Murgai and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 432 pages. Available in PDF, EPUB and Kindle. Book excerpt: Short turnaround has become critical in the design of electronic systems. Software- programmable components such as microprocessors and digital signal processors have been used extensively in such systems since they allow rapid design revisions. However, the inherent performance limitations of software-programmable systems mean that they are inadequate for high-performance designs. Designers thus turned to gate arrays as a solution. User-programmable gate arrays (field-programmable gate arrays, FPGAs) have recently emerged and are changing the way electronic systems are designed and implemented. The growing complexity of the logic circuits that can be packed onto an FPGA chip means that it has become important to have automatic synthesis tools that implement logic functions on these architectures. Logic Synthesis for Field-Programmable Gate Arrays describes logic synthesis for both look-up table (LUT) and multiplexor-based architectures, with a balanced presentation of existing techniques together with algorithms and the system developed by the authors. Audience: A useful reference for VLSI designers, developers of computer-aided design tools, and anyone involved in or with FPGAs.

Download or read book Automatic Speech and Speaker Recognition written by Chin-Hui Lee and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 524 pages. Available in PDF, EPUB and Kindle. Book excerpt: Research in the field of automatic speech and speaker recognition has made a number of significant advances in the last two decades, influenced by advances in signal processing, algorithms, architectures, and hardware. These advances include: the adoption of a statistical pattern recognition paradigm; the use of the hidden Markov modeling framework to characterize both the spectral and the temporal variations in the speech signal; the use of a large set of speech utterance examples from a large population of speakers to train the hidden Markov models of some fundamental speech units; the organization of speech and language knowledge sources into a structural finite state network; and the use of dynamic, programming based heuristic search methods to find the best word sequence in the lexical network corresponding to the spoken utterance. Automatic Speech and Speaker Recognition: Advanced Topics groups together in a single volume a number of important topics on speech and speaker recognition, topics which are of fundamental importance, but not yet covered in detail in existing textbooks. Although no explicit partition is given, the book is divided into five parts: Chapters 1-2 are devoted to technology overviews; Chapters 3-12 discuss acoustic modeling of fundamental speech units and lexical modeling of words and pronunciations; Chapters 13-15 address the issues related to flexibility and robustness; Chapter 16-18 concern the theoretical and practical issues of search; Chapters 19-20 give two examples of algorithm and implementational aspects for recognition system realization. Audience: A reference book for speech researchers and graduate students interested in pursuing potential research on the topic. May also be used as a text for advanced courses on the subject.

Download or read book Computer Aided Design Techniques for Low Power Sequential Logic Circuits written by José Monteiro and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 194 pages. Available in PDF, EPUB and Kindle. Book excerpt: Rapid increases in chip complexity, increasingly faster clocks, and the proliferation of portable devices have combined to make power dissipation an important design parameter. The power consumption of a digital system determines its heat dissipation as well as battery life. For some systems, power has become the most critical design constraint. Computer-Aided Design Techniques for Low Power Sequential Logic Circuits presents a methodology for low power design. The authors first present a survey of techniques for estimating the average power dissipation of a logic circuit. At the logic level, power dissipation is directly related to average switching activity. A symbolic simulation method that accurately computes the average switching activity in logic circuits is then described. This method is extended to handle sequential logic circuits by modeling correlation in time and by calculating the probabilities of present state lines. Computer-Aided Design Techniques for Low Power Sequential Logic Circuits then presents a survey of methods to optimize logic circuits for low power dissipation which target reduced switching activity. A method to retime a sequential logic circuit where registers are repositioned such that the overall glitching in the circuit is minimized is also described. The authors then detail a powerful optimization method that is based on selectively precomputing the output logic values of a circuit one clock cycle before they are required, and using the precomputed value to reduce internal switching activity in the succeeding clock cycle. Presented next is a survey of methods that reduce switching activity in circuits described at the register-transfer and behavioral levels. Also described is a scheduling algorithm that reduces power dissipation by maximising the inactivity period of the modules in a given circuit. Computer-Aided Design Techniques for Low Power Sequential Logic Circuits concludes with a summary and directions for future research.

Download or read book Software Synthesis from Dataflow Graphs written by Shuvra S. Bhattacharyya and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 198 pages. Available in PDF, EPUB and Kindle. Book excerpt: Software Synthesis from Dataflow Graphs addresses the problem of generating efficient software implementations from applications specified as synchronous dataflow graphs for programmable digital signal processors (DSPs) used in embedded real- time systems. The advent of high-speed graphics workstations has made feasible the use of graphical block diagram programming environments by designers of signal processing systems. A particular subset of dataflow, called Synchronous Dataflow (SDF), has proven efficient for representing a wide class of unirate and multirate signal processing algorithms, and has been used as the basis for numerous DSP block diagram-based programming environments such as the Signal Processing Workstation from Cadence Design Systems, Inc., COSSAP from Synopsys® (both commercial tools), and the Ptolemy environment from the University of California at Berkeley. A key property of the SDF model is that static schedules can be determined at compile time. This removes the overhead of dynamic scheduling and is thus useful for real-time DSP programs where throughput requirements are often severe. Another constraint that programmable DSPs for embedded systems have is the limited amount of on-chip memory. Off-chip memory is not only expensive but is also slower and increases the power consumption of the system; hence, it is imperative that programs fit in the on-chip memory whenever possible. Software Synthesis from Dataflow Graphs reviews the state-of-the-art in constructing static, memory-optimal schedules for programs expressed as SDF graphs. Code size reduction is obtained by the careful organization of loops in the target code. Data buffering is optimized by constructing the loop hierarchy in provably optimal ways for many classes of SDF graphs. The central result is a uniprocessor scheduling framework that provably synthesizes the most compact looping structures, called single appearance schedules, for a certain class of SDF graphs. In addition, algorithms and heuristics are presented that generate single appearance schedules optimized for data buffering usage. Numerous practical examples and extensive experimental data are provided to illustrate the efficacy of these techniques.

Download or read book Application Specific Processors written by Earl E. Swartzlander Jr. and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 266 pages. Available in PDF, EPUB and Kindle. Book excerpt: Application Specific Processors is written for use by engineers who are developing specialized systems (application specific systems). Traditionally, most high performance signal processors have been realized with application specific processors. The explanation is that application specific processors can be tailored to exactly match the (usually very demanding) application requirements. The result is that no `processing power' is wasted for unnecessary capabilities and maximum performance is achieved. A disadvantage is that such processors have been expensive to design since each is a unique design that is customized to the specific application. In the last decade, computer-aided design systems have been developed to facilitate the development of application specific integrated circuits. The success of such ASIC CAD systems suggests that it should be possible to streamline the process of application specific processor design. Application Specific Processors consists of eight chapters which provide a mixture of techniques and examples that relate to application specific processing. The inclusion of techniques is expected to suggest additional research and to assist those who are faced with the requirement to implement efficient application specific processors. The examples illustrate the application of the concepts and demonstrate the efficiency that can be achieved via application specific processors. The chapters were written by members and former members of the application specific processing group at the University of Texas at Austin. The first five chapters relate to specific arithmetic which often is the key to achieving high performance in application specific processors. The next two chapters focus on signal processing systems, and the final chapter examines the interconnection of possibly disparate elements to create systems.

Download or read book Advanced Concepts in Adaptive Signal Processing written by W. Kenneth Jenkins and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 316 pages. Available in PDF, EPUB and Kindle. Book excerpt: Although adaptive filtering and adaptive array processing began with research and development efforts in the late 1950's and early 1960's, it was not until the publication of the pioneering books by Honig and Messerschmitt in 1984 and Widrow and Stearns in 1985 that the field of adaptive signal processing began to emerge as a distinct discipline in its own right. Since 1984 many new books have been published on adaptive signal processing, which serve to define what we will refer to throughout this book as conventional adaptive signal processing. These books deal primarily with basic architectures and algorithms for adaptive filtering and adaptive array processing, with many of them emphasizing practical applications. Most of the existing textbooks on adaptive signal processing focus on finite impulse response (FIR) filter structures that are trained with strategies based on steepest descent optimization, or more precisely, the least mean square (LMS) approximation to steepest descent. While literally hundreds of archival research papers have been published that deal with more advanced adaptive filtering concepts, none of the current books attempt to treat these advanced concepts in a unified framework. The goal of this new book is to present a number of important, but not so well known, topics that currently exist scattered in the research literature. The book also documents some new results that have been conceived and developed through research conducted at the University of Illinois during the past five years.

Download or read book Electronic Design Automation for IC System Design Verification and Testing written by Luciano Lavagno and published by CRC Press. This book was released on 2017-12-19 with total page 644 pages. Available in PDF, EPUB and Kindle. Book excerpt: The first of two volumes in the Electronic Design Automation for Integrated Circuits Handbook, Second Edition, Electronic Design Automation for IC System Design, Verification, and Testing thoroughly examines system-level design, microarchitectural design, logic verification, and testing. Chapters contributed by leading experts authoritatively discuss processor modeling and design tools, using performance metrics to select microprocessor cores for integrated circuit (IC) designs, design and verification languages, digital simulation, hardware acceleration and emulation, and much more. New to This Edition: Major updates appearing in the initial phases of the design flow, where the level of abstraction keeps rising to support more functionality with lower non-recurring engineering (NRE) costs Significant revisions reflected in the final phases of the design flow, where the complexity due to smaller and smaller geometries is compounded by the slow progress of shorter wavelength lithography New coverage of cutting-edge applications and approaches realized in the decade since publication of the previous edition—these are illustrated by new chapters on high-level synthesis, system-on-chip (SoC) block-based design, and back-annotating system-level models Offering improved depth and modernity, Electronic Design Automation for IC System Design, Verification, and Testing provides a valuable, state-of-the-art reference for electronic design automation (EDA) students, researchers, and professionals.

Download or read book International Conference on VLSI and CAD written by and published by . This book was released on 1999 with total page 672 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book IEEE International Conference on Electronics Circuits and Systems written by and published by . This book was released on 2002 with total page 478 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Theory of CMOS Digital Circuits and Circuit Failures written by Masakazu Shoji and published by Princeton University Press. This book was released on 2014-07-14 with total page 589 pages. Available in PDF, EPUB and Kindle. Book excerpt: CMOS chips are becoming increasingly important in computer circuitry. They have been widely used during the past decade, and they will continue to grow in popularity in those application areas that demand high performance. Challenging the prevailing opinion that circuit simulation can reveal all problems in CMOS circuits, Masakazu Shoji maintains that simulation cannot completely remove the often costly errors that occur in circuit design. To address the failure modes of these circuits more fully, he presents a new approach to CMOS circuit design based on his systematizing of circuit design error and his unique theory of CMOS digital circuit operation. In analyzing CMOS digital circuits, the author focuses not on effects originating from the characteristics of the device (MOSFET) but on those arising from their connection. This emphasis allows him to formulate a powerful but ultimately simple theory explaining the effects of connectivity by using a concept of the states of the circuits, called microstates. Shoji introduces microstate sequence diagrams that describe the state changes (or the circuit connectivity changes), and he uses his microstate theory to analyze many of the conventional CMOS digital circuits. These analyses are practically all in closed-form, and they provide easy physical interpretation of the circuit's working mechanisms, the parametric dependence of performance, and the circuit's failure modes. Originally published in 1992. The Princeton Legacy Library uses the latest print-on-demand technology to again make available previously out-of-print books from the distinguished backlist of Princeton University Press. These editions preserve the original texts of these important books while presenting them in durable paperback and hardcover editions. The goal of the Princeton Legacy Library is to vastly increase access to the rich scholarly heritage found in the thousands of books published by Princeton University Press since its founding in 1905.

Download or read book EDA for IC System Design Verification and Testing written by Louis Scheffer and published by CRC Press. This book was released on 2018-10-03 with total page 617 pages. Available in PDF, EPUB and Kindle. Book excerpt: Presenting a comprehensive overview of the design automation algorithms, tools, and methodologies used to design integrated circuits, the Electronic Design Automation for Integrated Circuits Handbook is available in two volumes. The first volume, EDA for IC System Design, Verification, and Testing, thoroughly examines system-level design, microarchitectural design, logical verification, and testing. Chapters contributed by leading experts authoritatively discuss processor modeling and design tools, using performance metrics to select microprocessor cores for IC designs, design and verification languages, digital simulation, hardware acceleration and emulation, and much more. Save on the complete set.

Download or read book Application Specific Processors written by Earl E. Swartzlander and published by . This book was released on 1997 with total page 284 pages. Available in PDF, EPUB and Kindle. Book excerpt: Application Specific Processors consists of eight chapters which provide a mixture of techniques and examples that relate to application specific processing. The inclusion of techniques is expected to suggest additional research and to assist those who are faced with the requirement to implement efficient application specific processors. The examples illustrate the application of the concepts and demonstrate the efficiency that can be achieved via application specific processors. The chapters were written by members and former members of the application specific processing group at the University of Texas at Austin.