Download or read book Digital Signal Processing in Power Electronics Control Circuits written by Krzysztof Sozański and published by Springer Science & Business Media. This book was released on 2013-07-03 with total page 280 pages. Available in PDF, EPUB and Kindle. Book excerpt: Many digital control circuits in current literature are described using analog transmittance. This may not always be acceptable, especially if the sampling frequency and power transistor switching frequencies are close to the band of interest. Therefore, a digital circuit is considered as a digital controller rather than an analog circuit. This helps to avoid errors and instability in high frequency components. Digital Signal Processing in Power Electronics Control Circuits covers problems concerning the design and realization of digital control algorithms for power electronics circuits using digital signal processing (DSP) methods. This book bridges the gap between power electronics and DSP. The following realizations of digital control circuits are considered: digital signal processors, microprocessors, microcontrollers, programmable digital circuits. Discussed in this book is signal processing, starting from analog signal acquisition, through its conversion to digital form, methods of its filtration and separation, and ending with pulse control of output power transistors. The book is focused on two applications for the considered methods of digital signal processing: an active power filter and a digital class D power amplifier. The major benefit to readers is the acquisition of specific knowledge concerning discussions on the processing of signals from voltage or current sensors using a digital signal processor and to the signals controlling the output inverter transistors. Included are some Matlab examples for illustration of the considered problems.

Download or read book Digital Signal Processing in Power Electronics Control Circuits written by Krzysztof Sozanski and published by Springer. This book was released on 2013-07-06 with total page 265 pages. Available in PDF, EPUB and Kindle. Book excerpt: Many digital control circuits in current literature are described using analog transmittance. This may not always be acceptable, especially if the sampling frequency and power transistor switching frequencies are close to the band of interest. Therefore, a digital circuit is considered as a digital controller rather than an analog circuit. This helps to avoid errors and instability in high frequency components. Digital Signal Processing in Power Electronics Control Circuits covers problems concerning the design and realization of digital control algorithms for power electronics circuits using digital signal processing (DSP) methods. This book bridges the gap between power electronics and DSP. The following realizations of digital control circuits are considered: digital signal processors, microprocessors, microcontrollers, programmable digital circuits. Discussed in this book is signal processing, starting from analog signal acquisition, through its conversion to digital form, methods of its filtration and separation, and ending with pulse control of output power transistors. The book is focused on two applications for the considered methods of digital signal processing: an active power filter and a digital class D power amplifier. The major benefit to readers is the acquisition of specific knowledge concerning discussions on the processing of signals from voltage or current sensors using a digital signal processor and to the signals controlling the output inverter transistors. Included are some Matlab examples for illustration of the considered problems.

Download or read book Digital Signal Processing in Power System Protection and Control written by Waldemar Rebizant and published by Springer Science & Business Media. This book was released on 2011-07-28 with total page 324 pages. Available in PDF, EPUB and Kindle. Book excerpt: Digital Signal Processing in Power System Protection and Control bridges the gap between the theory of protection and control and the practical applications of protection equipment. Understanding how protection functions is crucial not only for equipment developers and manufacturers, but also for their users who need to install, set and operate the protection devices in an appropriate manner. After introductory chapters related to protection technology and functions, Digital Signal Processing in Power System Protection and Control presents the digital algorithms for signal filtering, followed by measurement algorithms of the most commonly-used protection criteria values and decision-making methods in protective relays. A large part of the book is devoted to the basic theory and applications of artificial intelligence techniques for protection and control. Fuzzy logic based schemes, artificial neural networks, expert systems and genetic algorithms with their advantages and drawbacks are discussed. AI techniques are compared and it is also shown how they can be combined to eliminate the disadvantages and magnify the useful features of particular techniques. The information provided in Digital Signal Processing in Power System Protection and Control can be useful for protection engineers working in utilities at various levels of the electricity network, as well as for students of electrical engineering, especially electrical power engineering. It may also be helpful for other readers who want to get acquainted with and to apply the filtering, measuring and decision-making algorithms for purposes other than protection and control, everywhere fast and on-line signal analysis is needed for proper functioning of the apparatus.

Download or read book Digital Signal Processing in Power Electronics Control Circuits written by Krzysztof Sozański and published by Springer. This book was released on 2017-05-10 with total page 340 pages. Available in PDF, EPUB and Kindle. Book excerpt: This revised and extended second edition covers problems concerning the design and realization of digital control algorithms for power electronics circuits using digital signal processing (DSP) methods. This book discusses signal processing, starting from analog signal acquisition, through conversion to digital form, methods of filtration and separation, and ending with pulse control of output power transistors. The book is focused on two applications for the considered methods of digital signal processing, a three-phase shunt active power filter and a digital class-D audio power amplifier. The book bridges the gap between power electronics and digital signal processing. Many control algorithms and circuits for power electronics in the current literature are described using analog transmittances. This may not always be acceptable, especially if half of the sampling frequencies and half of the power transistor switching frequencies are close to the band of interest. Therefore in this book, a digital circuit is treated as a digital circuit with its own peculiar characteristics, rather than an analog circuit. This helps to avoid errors and instability. This edition includes a new chapter dealing with selected problems of simulation of power electronics systems together with digital control circuits. The book includes numerous examples using MATLAB and PSIM programs.

Download or read book Programming and Application of a DSP to Control and Regulate Power Electronic Converters Programming in C written by Baris Bagci and published by diplom.de. This book was released on 2014-03-01 with total page 145 pages. Available in PDF, EPUB and Kindle. Book excerpt: The purpose of this project has been to study, operate and program the 32-bit 150MIPS TMS320F2812 DSP developed by Texas Instruments Inc. In addition, it has also been a goal to implement fast estimation techniques for control of resonant converters. For this purpose, PWM signals that are generated using this DSP are used. The demands on the system and the hardware to solve the problem were already decided when I started the work. The algorithms were programmed in C/C++ language, compiled, debugged and transferred to the DSP development board in a compiling and simulation tool (downloader), called CCS (Code Composer Studio v2), also provided by Texas Instruments. In the first chapters of this study I give general information about control systems, digital signal processors, digital signal processing and the DSP used in this work. The following chapters tell about PWM, how to configure the PWM outputs and some examples related with PWM signals are given. After a short review of series resonant converters, I presented the last example implemented in this project. I conclude with a summary and provide some hints of future work.

Download or read book Control Circuits in Power Electronics written by Miguel Castilla and published by IET. This book was released on 2016-05-16 with total page 457 pages. Available in PDF, EPUB and Kindle. Book excerpt: Resource added for the Electronics/Biomedical Technology program 106051.

Download or read book Intelligent Systems and Signal Processing in Power Engineering written by Abhisek Ukil and published by Springer Science & Business Media. This book was released on 2007-09-23 with total page 384 pages. Available in PDF, EPUB and Kindle. Book excerpt: This highly experienced author sets out to build a bridge between two inter-disciplinary power engineering practices. The book looks into two major fields used in modern power systems: intelligent systems and the signal processing. The intelligent systems section comprises fuzzy logic, neural network and support vector machine. The author looks at relevant theories on the topics without assuming much particular background. Following the theoretical basics, he studies their applications in various problems in power engineering, like, load forecasting, phase balancing, or disturbance analysis.

Download or read book Signal Processing and Analysis of Electrical Circuit written by Adam Glowacz and published by MDPI. This book was released on 2020-03-13 with total page 604 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Special Issue with 35 published articles shows the significance of the topic “Signal Processing and Analysis of Electrical Circuit”. This topic has been gaining increasing attention in recent times. The presented articles can be categorized into four different areas: signal processing and analysis methods of electrical circuits; electrical measurement technology; applications of signal processing of electrical equipment; fault diagnosis of electrical circuits. It is a fact that the development of electrical systems, signal processing methods, and circuits has been accelerating. Electronics applications related to electrical circuits and signal processing methods have gained noticeable attention in recent times. The methods of signal processing and electrical circuits are widely used by engineers and scientists all over the world. The constituent papers represent a significant contribution to electronics and present applications that can be used in industry. Further improvements to the presented approaches are required for realizing their full potential.

Download or read book Digital Power Electronics and Applications written by Fang Lin Luo and published by Elsevier. This book was released on 2010-07-20 with total page 422 pages. Available in PDF, EPUB and Kindle. Book excerpt: The purpose of this book is to describe the theory of Digital Power Electronics and its applications. The authors apply digital control theory to power electronics in a manner thoroughly different from the traditional, analog control scheme. In order to apply digital control theory to power electronics, the authors define a number of new parameters, including the energy factor, pumping energy, stored energy, time constant, and damping time constant. These parameters differ from traditional parameters such as the power factor, power transfer efficiency, ripple factor, and total harmonic distortion. These new parameters result in the definition of new mathematical modeling: • A zero-order-hold (ZOH) is used to simulate all AC/DC rectifiers. • A first-order-hold (FOH) is used to simulate all DC/AC inverters. • A second-order-hold (SOH) is used to simulate all DC/DC converters. • A first-order-hold (FOH) is used to simulate all AC/AC (AC/DC/AC) converters. Presents most up-to-date methods of analysis and control algorithms for developing power electronic converters and power switching circuits Provides an invaluable reference for engineers designing power converters, commercial power supplies, control systems for motor drives, active filters, etc. Presents methods of analysis not available in other books

Download or read book Digital Control in Power Electronics written by Simone Buso and published by Springer Nature. This book was released on 2007-12-31 with total page 153 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the reader, whether an electrical engineering student in power electronics or a design engineer, some typical power converter control problems and their basic digital solutions, based on the most widespread digital control techniques. The presentation is focused on different applications of the same power converter topology, the half-bridge voltage source inverter, considered both in its single- and three-phase implementation. This is chosen as the case study because, besides being simple and well known, it allows the discussion of a significant spectrum of the more frequently encountered digital control applications in power electronics, from digital pulse width modulation (DPWM) and space vector modulation (SVM), to inverter output current and voltage control. The book aims to serve two purposes: to give a basic, introductory knowledge of the digital control techniques applied to power converters, and to raise the interest for discrete time control theory, stimulating new developments in its application to switching power converters.

Download or read book Integrated Power Electronic Converters and Digital Control written by Ali Emadi and published by CRC Press. This book was released on 2017-12-19 with total page 350 pages. Available in PDF, EPUB and Kindle. Book excerpt: Because of the demand for higher efficiencies, smaller output ripple, and smaller converter size for modern power electronic systems, integrated power electronic converters could soon replace conventional switched-mode power supplies. Synthesized integrated converters and related digital control techniques address problems related to cost, space, flexibility, energy efficiency, and voltage regulation—the key factors in digital power management and implementation. Meeting the needs of professionals working in power electronics, as well as advanced engineering students, Integrated Power Electronic Converters and Digital Control explores the many benefits associated with integrated converters. This informative text details boost type, buck type, and buck-boost type integrated topologies, as well as other integrated structures. It discusses concepts behind their operation as well specific applications. Topics discussed include: Isolated DC-DC converters such as flyback, forward, push-pull, full-bridge, and half-bridge Power factor correction and its application Definition of the integrated switched-mode power supplies Steady-state analysis of the boost integrated flyback rectifier energy storage converter Dynamic analysis of the buck integrated forward converter Digital control based on the use of digital signal processors (DSPs) With innovations in digital control becoming ever more pervasive, system designers continue to introduce products that integrate digital power management and control integrated circuit solutions, both hybrid and pure digital. This detailed assessment of the latest advances in the field will help anyone working in power electronics and related industries stay ahead of the curve.

Download or read book Power Electronics and Control Techniques for Maximum Energy Harvesting in Photovoltaic Systems written by Nicola Femia and published by CRC Press. This book was released on 2017-07-12 with total page 366 pages. Available in PDF, EPUB and Kindle. Book excerpt: Incentives provided by European governments have resulted in the rapid growth of the photovoltaic (PV) market. Many PV modules are now commercially available, and there are a number of power electronic systems for processing the electrical power produced by PV systems, especially for grid-connected applications. Filling a gap in the literature, Power Electronics and Control Techniques for Maximum Energy Harvesting in Photovoltaic Systems brings together research on control circuits, systems, and techniques dedicated to the maximization of the electrical power produced by a photovoltaic (PV) source. Tools to Help You Improve the Efficiency of Photovoltaic Systems The book supplies an overview of recent improvements in connecting PV systems to the grid and highlights various solutions that can be used as a starting point for further research and development. It begins with a review of methods for modeling a PV array working in uniform and mismatched conditions. The book then discusses several ways to achieve the best maximum power point tracking (MPPT) performance. A chapter focuses on MPPT efficiency, examining the design of the parameters that affect algorithm performance. The authors also address the maximization of the energy harvested in mismatched conditions, in terms of both power architecture and control algorithms, and discuss the distributed MPPT approach. The final chapter details the design of DC/DC converters, which usually perform the MPPT function, with special emphasis on their energy efficiency. Get Insights from the Experts on How to Effectively Implement MPPT Written by well-known researchers in the field of photovoltaic systems, this book tackles state-of-the-art issues related to how to extract the maximum electrical power from photovoltaic arrays under any weather condition. Featuring a wealth of examples and illustrations, it offers practical guidance for researchers and industry professionals who want to implement MPPT in photovoltaic systems.

Download or read book Programming and Use of TMS320F2812 DSP to Control and Regulate Power Electronic Converters written by Baris Bagci and published by Grin Publishing. This book was released on 2007-08 with total page 145 pages. Available in PDF, EPUB and Kindle. Book excerpt: Master's Thesis from the year 2003 in the subject Electrotechnology, grade: 1 (A), Cologne University of Applied Sciences (Institute for Automation Technology), language: English, abstract: The purpose of this master thesis project has been to study, operate and program the 32-bit 150MIPS TMS320F2812 DSP developed by Texas Instruments Inc. In addition, it has also been a goal to implement fast estimation techniques for control of resonant converters. For this purpose, PWM signals that are generated using this DSP are used. The demands on the system and the hardware to solve the problem were already decided when I started the work. The algorithms were programmed in C/C++ language, compiled, debugged and transferred to the DSP development board in a compiling and simulation tool (downloader), called CCS (Code Composer Studio v2), also provided by Texas Instruments. In the first chapters of this thesis I give general information about control systems, digital signal processors, digital signal processing and the DSP used in this work. The following chapters tell about PWM, how to configure the PWM outputs and some examples related with PWM signals are given. After a short review of series resonant converters, I presented the last example implemented in this project. I conclude with a summary and provide some hints of future work.

Download or read book DSP Software Development Techniques for Embedded and Real Time Systems written by Robert Oshana and published by Elsevier. This book was released on 2006-01-09 with total page 608 pages. Available in PDF, EPUB and Kindle. Book excerpt: Today's embedded and real-time systems contain a mix of processor types: off-the-shelf microcontrollers, digital signal processors (DSPs), and custom processors. The decreasing cost of DSPs has made these sophisticated chips very attractive for a number of embedded and real-time applications, including automotive, telecommunications, medical imaging, and many others—including even some games and home appliances. However, developing embedded and real-time DSP applications is a complex task influenced by many parameters and issues. DSP Software Development Techniques for Embedded and Real-Time Systems is an introduction to DSP software development for embedded and real-time developers giving details on how to use digital signal processors efficiently in embedded and real-time systems. The book covers software and firmware design principles, from processor architectures and basic theory to the selection of appropriate languages and basic algorithms. The reader will find practical guidelines, diagrammed techniques, tool descriptions, and code templates for developing and optimizing DSP software and firmware. The book also covers integrating and testing DSP systems as well as managing the DSP development effort. Digital signal processors (DSPs) are the future of microchips! Includes practical guidelines, diagrammed techniques, tool descriptions, and code templates to aid in the development and optimization of DSP software and firmware

Download or read book Real time Digital Signal Processing written by Sen-Maw Kuo and published by 清华大学出版社有限公司. This book was released on 2003 with total page 524 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Digital Control in Power Electronics written by Simone Buso and published by Morgan & Claypool Publishers. This book was released on 2015-05-01 with total page 231 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the reader, whether an electrical engineering student in power electronics or a design engineer, a selection of power converter control problems and their basic digital solutions, based on the most widespread digital control techniques. The presentation is primarily focused on different applications of the same power converter topology, the half-bridge voltage source inverter, considered both in its single- and three-phase implementation. This is chosen as the test case because, besides being simple and well known, it allows the discussion of a significant spectrum of the most frequently encountered digital control applications in power electronics, from digital pulse width modulation (DPWM) and space vector modulation (SVM), to inverter output current and voltage control, ending with the relatively more complex VSI applications related to the so called smart-grid scenario. This book aims to serve two purposes: (1) to give a basic, introductory knowledge of the digital control techniques applied to power converters; and (2) to raise the interest for discrete time control theory, stimulating new developments in its application to switching power converters.

Download or read book Advanced Digital Signal Processing written by Glenn Zelniker and published by CRC Press. This book was released on 1993-10-28 with total page 694 pages. Available in PDF, EPUB and Kindle. Book excerpt: Provides a detailed treatment of the concepts and applications of advanced digital signal processing.