Download or read book Development of Traffic Inputs for the Mechanistic empirical Pavement Design Guide in New York State written by Ferdous Intaj and published by . This book was released on 2012 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Proper characterization of traffic data is a prerequisite for the determination of appropriate traffic inputs to Mechanistic-Empirical Pavement Design Guide (MEPDG). The development of proper traffic inputs helps reflect the traffic conditions over the life of pavement which would decrease the maintenance, repair and traffic disruptions and improve the traffic conditions of a road network. The objective of the study was to characterize the traffic data and suggest the sitespecific, regional or state wide average values for traffic inputs to MEPDG for New York State. Vehicle class distribution (VCD), monthly distribution factors (MDF), hourly distribution factors (HDF), average number of axle groups per vehicle (AGPV) and axle load spectra were obtained from vehicle classification and WIM sites in New York State for the years of 2007-2011. These traffic data was processed with TrafLoad software. Cluster analysis was performed on the processed VCD, MDF and HDF data collected during the time period. This statistical analysis could not be done for AGPV values and axle load spectra due to the unavailability of sufficient number of WIM sites. However, MEPDG runs were carried out to investigate the effect of the variability of traffic inputs on the pavement performance of typical new flexible and rigid pavement structures. The statistical analysis showed consistent results for VCD and HDF over the years. However, the results of statistical analysis on MDF were not consistent over the time period. Site specific values for VCD, MDF, AGPV and axle load spectra showed little variation with statewide average values after the cluster analysis and MEPDG runs for the vehicle classification and WIM data of the year of 2010. This was observed for both flexible and rigid pavements. However, HDF did not show any effect on the design of pavement with MEPDG. These findings were also verified from the analysis of vehicle classification and WIM data of the other years.
Download or read book Mechanistic empirical Pavement Design Guide written by American Association of State Highway and Transportation Officials and published by AASHTO. This book was released on 2008 with total page 218 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Development of Traffic Data Input Resources for the Mechanistic Empirical Pavement Design Process written by John Randolph Stone and published by . This book was released on 2011 with total page 225 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Implementation Plan for the New Mechanistic empirical Pavement Design Guide written by Y. Richard Kim and published by . This book was released on 2007 with total page 690 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Mechanistic empirical Pavement Design Guide Implementation Plan written by Todd E. Hoerner and published by . This book was released on 2007 with total page 324 pages. Available in PDF, EPUB and Kindle. Book excerpt: As AASH is expected to eventually adopt the MEPDG at its primary pavement design method, it is critical that the SDDOT become familiar with the MEPGD documentation and associated design software. The research conducted under this project was a first step toward achieving this goal.
Download or read book Traffic Characterization for a Mechanistic empirical Pavement Design written by Jorge A. Prozzi and published by . This book was released on 2006 with total page 164 pages. Available in PDF, EPUB and Kindle. Book excerpt: The goal of this research study was to assess and address the implications of the axle load spectra approach proposed by the M-E Design Guide. In addition, recommendations were developed regarding traffic data needs and availability to aid in deciding the installation locations of future WIM stations in Texas. A methodology for specifying the required accuracy of WIM equipment based on the effect that this accuracy has on pavement performance prediction was also developed. Regarding traffic volume forecasting, a methodology is presented that allows optimum use of available data by simultaneously estimating traffic growth and seasonal traffic variability.
Download or read book Guide for the Local Calibration of the Mechanistic empirical Pavement Design Guide written by and published by AASHTO. This book was released on 2010 with total page 202 pages. Available in PDF, EPUB and Kindle. Book excerpt: This guide provides guidance to calibrate the Mechanistic-Empirical Pavement Design Guide (MEPDG) software to local conditions, policies, and materials. It provides the highway community with a state-of-the-practice tool for the design of new and rehabilitated pavement structures, based on mechanistic-empirical (M-E) principles. The design procedure calculates pavement responses (stresses, strains, and deflections) and uses those responses to compute incremental damage over time. The procedure empirically relates the cumulative damage to observed pavement distresses.
Download or read book Mechanistic empirical Pavement Design Guide written by and published by . This book was released on 2015 with total page 200 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book AASHTO Guide for Design of Pavement Structures 1993 written by American Association of State Highway and Transportation Officials and published by AASHTO. This book was released on 1993 with total page 622 pages. Available in PDF, EPUB and Kindle. Book excerpt: Design related project level pavement management - Economic evaluation of alternative pavement design strategies - Reliability / - Pavement design procedures for new construction or reconstruction : Design requirements - Highway pavement structural design - Low-volume road design / - Pavement design procedures for rehabilitation of existing pavements : Rehabilitation concepts - Guides for field data collection - Rehabilitation methods other than overlay - Rehabilitation methods with overlays / - Mechanistic-empirical design procedures.
Download or read book Recommended Mechanistic empirical Pavement Design Guide and Software written by National Cooperative Highway Research Program and published by . This book was released on 2004 with total page 6 pages. Available in PDF, EPUB and Kindle. Book excerpt: "This digest announces the availability of key products from NCHRP Project 1-37A, 'Development of the 2002 guide for the design of new and rehabilitated pavement structures: phase II, ' for evaluation"--Page 1 excerpt
Download or read book Implementing the Mechanistic empirical Pavement Design Guide written by Brian Coree and published by . This book was released on 2005 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Implementation of the AASHTO Mechanistic empirical Pavement Design Guide and Software written by and published by . This book was released on 2014 with total page 84 pages. Available in PDF, EPUB and Kindle. Book excerpt: Introduction -- Mechanistic-Empirical Pavement Design Guide and AASHTOWare Pavement ME Design (TM) Software Overview -- Survey of Agency Pavement Design Practices -- Common Elements of Agency Implementation Plans -- Case Examples of Agency Implementation -- Conclusions.
Download or read book Local Calibration of Mechanistic Empirical Pavement Design Guide for North Eastern United States written by Shariq A. Momin and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The Mechanistic-Empirical Pavement Design Guide (MEPDG) developed under the National Cooperative Highway Research Program (NCHRP) 1-37A project is based on mechanistic-empirical analysis of the pavement structure to predict the performance of the pavement under different sets of conditions (traffic, structure and environment). MEPDG takes into account the advanced modeling concepts and pavement performance models in performing the analysis and design of pavement. The mechanistic part of the design concept relies on the application of engineering mechanics to calculate stresses, strains and deformations in the pavement structure induced by the vehicle loads. The empirical part of the concept is based on laboratory developed performance models that are calibrated with the observed distresses in the in-service pavements with known structural properties, traffic loadings, and performances. These models in the MEPDG were calibrated using a national database of pavement performance data (Long Term Pavement Performance, LTPP) and will provide design solution for pavements with a national average performance. In order to improve the performance prediction of the models and the efficiency of the design for a given state, it is necessary to calibrate it to local conditions by taking into consideration locally available materials, traffic information and the environmental conditions. The objective of this study was to calibrate the MEPDG flexible pavement performance models to local conditions of Northeastern region of United States. To achieve this, seventeen pavement sections were selected for the calibration process and the relevant data (structural, traffic, climatic and pavement performance) was obtained from the LTPP database. MEPDG software (Version 1.1) simulation runs were made using the nationally calibrated coefficients and the MEPDG predicted distresses were compared with the LTPP measured distresses (rutting, alligator and longitudinal cracking, thermal cracking and IRI). The predicted distresses showed fair agreement with the measured distresses but still significant differences were found. The difference between the measured and the predicted distresses were minimized through recalibration of the MEPDG distress models. For the permanent deformation models of each layer, a simple linear regression with no intercept was performed and a new set of model coefficients (ßr1, ßGB, and ßSG) for asphalt concrete, granular base and subgrade layer models were calculated. The calibration of alligator (bottom-up fatigue cracking) and longitudinal (topdown fatigue cracking) was done by deriving the appropriate model coefficients (C1, C2, and C4) since the fatigue damage is given in MEDPG software output. Thermal cracking model was not calibrated since the measured transverse cracking data in the LTPP database did not increase with time, as expected to increase with time. The calibration of IRI model was done by computing the model coefficients (C1, C2, C3, and C4) based on other distresses (rutting, total fatigue cracking, and transverse cracking) by performing a simple linear regression.
Download or read book Joint Design Methods Developed for the NYS Pavement Design Manual written by Luis Julian Bendaña and published by . This book was released on 1992 with total page 10 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Development of a Master Plan for Calibration and Implementation of the Mechanistic Empirical Pavement Design Guide written by Kevin Dale Hall and published by . This book was released on 2015 with total page 35 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book From Fundamentals to Applications in Geotechnics written by D. Manzanal and published by IOS Press. This book was released on 2015-12-11 with total page 3344 pages. Available in PDF, EPUB and Kindle. Book excerpt: The work of geotechnical engineers contributes to the creation of safe, economic and pleasant spaces to live, work and relax all over the world. Advances are constantly being made, and the expertise of the profession becomes ever more important with the increased pressure on space and resources. This book presents the proceedings of the 15th Pan-American Conference on Soil Mechanics and Geotechnical Engineering (XV PCSMGE), held in Buenos Aires, Argentina, in November 2015. This conference, held every four years, is an important opportunity for international experts, researchers, academics, professionals and geo-engineering companies to meet and exchange ideas and research findings in the areas of soil mechanics, rock mechanics, and their applications in civil, mining and environmental engineering. The articles are divided into nine sections: transportation geotechnics; in-situ testing; geo-engineering for energy and sustainability; numerical modeling in geotechnics; foundations and ground improvement; unsaturated soil behavior; embankments, dams and tailings; excavations and tunnels; and geo-risks, and cover a wide spectrum of issues from fundamentals to applications in geotechnics. This book will undoubtedly represent an essential reference for academics, researchers and practitioners in the field of soil mechanics and geotechnical engineering. In this proceedings, approximately 65% of the contributions are in English, and 35% of the contributions are in Spanish or Portuguese.
Download or read book Adapting the AASHTO Pavement Design Guide to New York State Conditions written by Hong-Jer Chen and published by . This book was released on 1995 with total page 84 pages. Available in PDF, EPUB and Kindle. Book excerpt:
