Download or read book Development of Terahertz Frequency Quantum Cascade Lasers written by Mohammed Salih and published by . This book was released on 2011 with total page 344 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Spectroscopic Applications of Terahertz Quantum Cascade Lasers written by Tasmim Alam and published by Cuvillier Verlag. This book was released on 2020-10-29 with total page 132 pages. Available in PDF, EPUB and Kindle. Book excerpt: Quantum cascade lasers (QCLs) are attractive for high-resolution spectroscopy because they can provide high power and a narrow linewidth. They are particularly promising in the terahertz (THz) range since they can be used as local oscillators for heterodyne detection as well as transmitters for direct detection. However, THz QCL-based technologies are still under development and are limited by the lack of frequency tunability as well as the frequency and output power stability for free-running operation. In this dissertation, frequency tuning and linewidth of THz QCLs are studied in detail by using rotational spectroscopic features of molecular species. In molecular spectroscopy, the Doppler eff ect broadens the spectral lines of molecules in the gas phase at thermal equilibrium. Saturated absorption spectroscopy has been performed that allows for sub-Doppler resolution of the spectral features. One possible application is QCL frequency stabilization based on the Lamb dip. Since the tunability of the emission frequency is an essential requirement to use THz QCL for high-resolution spectroscopy, a new method has been developed that relies on near-infrared (NIR) optical excitation of the QCL rear-facet. A wide tuning range has been achieved by using this approach. The scheme is straightforward to implement, and the approach can be readily applied to a large class of THz QCLs. The frequency and output stability of the local oscillator has a direct impact on the performance and consistency of the heterodyne spectroscopy. A technique has been developed for a simultaneous stabilization of the frequency and output power by taking advantage of the frequency and power regulation by NIR excitation. The results presented in this thesis will enable the routine use of THz QCLs for spectroscopic applications in the near future.

Download or read book Development of Terahertz QCLs written by Sushil Kumar (Ph. D.) and published by . This book was released on 2007 with total page 340 pages. Available in PDF, EPUB and Kindle. Book excerpt: The terahertz or the far-infrared frequency range of the electromagnetic spectrum (...) has historically been technologically underdeveloped despite having many potential applications, primarily due to lack of suitable sources of coherent radiation. Following on the remarkable development of mid-infrared (...) quantum-cascade lasers (QCLs) in the past decade, this thesis describes the development of electrically-pumped terahertz quantum-cascade lasers in GaAs/AlsGal_. As heterostructures that span a spectral range of 1.59 - 5.0 THz (...). A quantum-cascade laser (QCL) emits photons due to electronic intersubband transitions in the quantum-wells of a semiconductor heterostructure. The operation of terahertz QCLs at frequencies below the Reststrahlen band in the semiconductor (...), is significantly more challenging as compared to that of the mid-infrared QCLs. Firstly, due to small energy separation between the laser levels various intersubband scattering mechanisms are activated, which make it difficult to selectively depopulate the lower laser level. Additionally, as electrons gain enough kinetic energy in the upper laser level thermally activated longitudinal-optical (LO) phonon scattering reduces the level lifetime and makes it difficult to sustain population inversion at higher temperatures. Secondly, waveguide design for terahertz mode confinement is also more challenging due to higher free-carrier losses in the semiconducting doped regions at the terahertz frequencies. For successful designs reported in this work, the lower radiative state depopulation is achieved by a combination of resonant-tunneling and fast LO phonon scattering, which allow robust operation even at relatively high temperatures. An equally important enabling mechanism for these lasers is the development of metal-metal waveguides, which provide low waveguides losses, and strong mode confinement due to subwavelength mode localization in the vertical dimension. With these techniques some record performances for terahertz QCLs are demonstrated including the highest pulsed operating temperature of 169 K, the highest continuous-wave (cw) operating temperature of 117 K, and the highest optical power output (248 mW in pulsed and 138 mW in cw at 5 K) for any terahertz QCL. Towards the bigger goal of realizing a 1-THz solid-state laser to ultimately bridge the gap between electronic and optical sources of electromagnetic radiation, QCLs with a unique one-well injection scheme, which minimizes intersubband absorption losses that occur at longer wavelengths, are developed. Based on this scheme a QCL operating at 1.59 THz (A - 189 ym) is realized, which is amongst the lowest frequency solid-state lasers that operate without the assistance of a magnetic field. This thesis also reports on the development of distributed-feedback lasers in metal-metal waveguides to obtain single-mode operation, with greater output power and better beam quality. The subwavelength vertical dimension in these waveguides leads to a strongly coupled DFB action and a large reflection from the end-facets, and thus conventional coupled-mode theory is not directly applicable to the DFB design. A design technique with precise control of phase of reflection at the end-facets is developed with the aid of finite-element analysis, and with some additional unique design and fabrication methods, robust DFB operation has been obtained. Single-mode surface-emitting terahertz QCLs operating up to - 150 K are demonstrated, with different grating devices spanning a range of approximately 0.35 THz around v - 3 THz using the same gain medium. A single-lobed far-field radiation pattern, higher output power due to surface-emission, and a relatively small degradation in temperature performance compared to the Fabry-Perot ridge lasers makes these DFB lasers well suited for practical applications that are being targeted by the terahertz quantum-cascade lasers.

Download or read book Development of Terahertz Frequency Quantum Cascade Laser written by Mohammed Salih and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: THz QCLs, based on a three-well resonant-phonon depopulation active region design, have been studied in depth using semi-insulating surface plasmon waveguides. Lasing frequencies between 2.3 to 4.0 THz have been investigated, together with a detailed evaluation of the effect of cavity length on devices performance. The effect of reducing the thickness of the THz QCL active region from 10 to 5 IJm was investigated, and the influence of active region thickness on lattice temperatures compared. Thinner active regions potentially make it possible to obtain continuous-wave (CW) operation from three-well, resonant-phonon depopulation QCLs, which is a requirement for many applications. It was demonstrated that the laser cavity of edge-emitting THz QCLs could be defined using an etched rather than a cleaved facet. Three emission frequencies ( - 3.0, - 3.5 and - 4.0 THz) with two different facet angles (et:> = - 50° and et:> = - 42°) were studied and device performance were compared. The new THz QCL devices with sloped facets could open up the possibility of monolithic integration of QCLs into terahertz circuits. They also remove the requirement for THz QCLs to be fabricated perpendicular to cleavage planes of the underlying crystal structure. From the demonstration of lasing from THz QCLs with angled facets, the possibility of coupling surface acoustic waves (SAWs) with THz QCLs is investigated. The aim was to use SAWs propagating through upper surface of the waveguide of the THz QCL to introduce modulation of the gain region. This would have significant application to spectroscopy at THz frequencies. SAW propagate across a QCL mesa was demonstrated, and fully investigated devices were fabricated and tested.

Download or read book Magneto spectroscopy and Development of Terahertz Quantum Cascade Lasers written by and published by . This book was released on with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: In this work we concentrate our efforts on the generation of laser emission at low THz frequencies (3-1 THz range) employing the quantum cascade technology. Quantum cascade (QC) lasers are unipolar semiconductor lasers based on intersubband transitions in quantum wells that cover a large portion of the Mid and Far Infrared electromagnetic spectrum. Two main research lines have been followed: (i) the development of quantum cascade lasers based on population inversion between parabolic subbands and (ii) the development of low frequency QC lasers based on a three-dimensional electron confinement induced by an external magnetic field. (i) : Gain and laser action have been demonstrated in different systems at frequencies of 3.4 3.6 THz exploiting bound-to-bound and bound-to-continuum optical transition. A QC laser emitting at 3.6 THz and based on a vertical transition and resonant tunneling in a single quantum well has been demonstrated. To overcome the limitations in performance of such a system, an heterostructure laser based on a bound-to-continuum transition has been developed. The structure was the first one to operate above the technologically important temperature of liquid nitrogen. With a further development of the bound-to-continuum design that includes lower state lifetime reduction by optical phonon emission, laser action was successfully achieved at 115 K.A study of different waveguide mechanisms suitable for different THz frequencies has also been carried out. (ii) : THz quantum cascade lasers based on the in-plane confinement introduced by a strong magnetic field applied perpendiculary to the plane of the layers have been developed. A model system based on large single quantum wells (50-60 nm wide) has been exploited to study this gain mechanism. Such an approach led to the extension of the frequency range of operation of QC lasers, with the demonstration of laser action at 1.39 THz (220 mm) which is the lowest frequency observed to-date for this kind of.

Download or read book Physics and Applications of Terahertz Radiation written by Matteo Perenzoni and published by Springer. This book was released on 2013-10-16 with total page 257 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers the latest advances in the techniques employed to manage the THz radiation and its potential uses. It has been subdivided in three sections: THz Detectors, THz Sources, Systems and Applications. These three sections will allow the reader to be introduced in a logical way to the physics problems of sensing and generation of the terahertz radiation, the implementation of these devices into systems including other components and finally the exploitation of the equipment for real applications in some different field. All of the sections and chapters can be individually addressed in order to deepen the understanding of a single topic without the need to read the whole book. The THz Detectors section will address the latest developments in detection devices based on three different physical principles: photodetection, thermal power detection, rectification. The THz Sources section will describe three completely different generation methods, operating in three separate scales: quantum cascade lasers, free electron lasers and non-linear optical generation. The Systems and Applications section will take care of introducing many of the aspects needed to move from a device to an equipment perspective: control of terahertz radiation, its use in imaging or in spectroscopy, potential uses in security, and will address also safety issues. The text book is at a level appropriate to graduate level courses up to researchers in the field who require a reference book covering all aspects of terahertz technology.

Download or read book Development of Terahertz Quantum cascade VECSELs written by Christopher Curwen and published by . This book was released on 2019 with total page 184 pages. Available in PDF, EPUB and Kindle. Book excerpt: Terahertz (THz) quantum-cascade lasers (QCLs) are an emerging semiconductor source of compact, high-power THz radiation. Though first realized more than 15 years ago, THz QCLs continue to suffer from poor beam quality and outcoupling efficiency due to the subwavelength nature of the semiconductor ridge-waveguides typically used. In this thesis, a new technique is discussed for obtaining high power and good beam quality from THz QCLs, the THz quantum-cascade external cavity surface emitting laser (QC-VECSEL). The concept of the QC-VECSEL is to use THz QC-gain material to design a millimeter-scale reflective amplifying surface, or metasurface, for free space THz waves and incorporate it into a free-space THz resonant cavity to provide feedback to the amplification and form a laser. In this manner, the beam shape is determined by the external cavity, which supports fundamental Gaussian solutions. Further, the metasurface itself is composed of a subwavelength array (to prevent diffraction) of surface-coupled QC-elements whose properties, such as phase and polarization response, can be engineered on a unit cell basis allowing for a variety of unique experiments. The power output power of the QC-VECSEL can be scaled by either increasing the size of the metasurface, or increasing the density (or fill factor) of QC-elements across the surface. In this work, large area metasurfaces with high fill-factor have been studied and demonstrated up to 1.35 W of peak output power for a QC-VECSEL operating at 3.4 THz at a heat sink temperature of 4 K. A peak wall-plug efficiency of ~2% is demonstrated, but observation of self lasing from the metasurface at high bias (when no external cavity is provided) in combination with a simultaneous roll-off in VECSEL output power suggests even higher efficiency can be achieved with improved suppression of self-lasing modes. The output beam is well fit to a Gaussian distribution with a 4 degree full-width half-maximum divergence angle. In addition to power and beam quality, the QC-VECSEL opens the door to many interesting and unique studies via engineering of the metasurface properties and external cavity. Much of this thesis describes frequency tuning of QC-VECSELs based on broadband metasurfaces by varying the length of the external cavity. By making the external cavity extremely short (comparable to the operating wavelength), we are able to push all other external cavity modes outside of the gain bandwidth of the metasurface and demonstrate more than 20% fractional single-mode tuning around a center operating frequency of 3.5 THz. Because there are almost no diffraction losses at such a short cavity, the size of the metasurface could be reduced, allowing for continuous wave lasing with up to 20 milliwatts of output power at a heatsink temperature of 77 K, though the output power is highly variable as the reflectance of the output coupler has a strong frequency dependence. At the time of writing this, these are record performances in both frequency tuning and high-temperature continuous wave operation for lasers based on THz QC-gain material. The amount of tuning that be achieved with this approach is limited by the phase response of the metasurface, which squeezes the external cavity modes closer together in the spectral domain. Development of metasurfaces with lower electrical power consumption and higher conversion efficiency for the purpose of improving continuous wave performance. A sparse, patch-based metasurface with reduced power consumption is demonstrated, though the design was not optimal and only showed a 20% reduction in current draw compared to the previously demonstrated metasurfaces. Routes towards improving the performance are discussed. The last subject discussed is the design of a mid-infrared (IR) QC-VECSEL. Due to the large metal losses at mid-IR frequencies compared to THz, the technique used to develop THz QC-VECSELs cannot be directly extended to the mid-IR. We propose a scheme based on a diffraction grating to provide surface coupling of the QC-gain material. Progress on experimental realization is discussed, but lasing has not yet been observed.

Download or read book Development of Terahertz Quantum cascade Lasers as Sources for Heterodyne Receivers written by Martin Wienold and published by . This book was released on 2012 with total page 214 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Terahertz Quantum Cascade Lasers written by Benjamin Stanford Williams and published by . This book was released on 2003 with total page 310 pages. Available in PDF, EPUB and Kindle. Book excerpt: The development of the terahertz frequency range has long been impeded by the relative dearth of compact, coherent radiation sources of reasonable power. This thesis details the development of quantum cascade lasers (QCLs) that operate in the terahertz with photon energies below the semiconductor Reststrahlen band. Photons are emitted via electronic intersubband transitions that take place entirely within the conduction band, where the wavelength is chosen by engineering the well and barrier widths in multiple-quantum-well heterostructures. Fabrication of such long wavelength lasers has traditionally been challenging, since it is difficult to obtain a population inversion between such closely spaced energy levels, and because traditional dielectric waveguides become extremely lossy due to free carrier absorption. This thesis reports the development of terahertz QCLs in which the lower radiative state is depopulated via resonant longitudinal-optical phonon scattering. This mechanism is efficient and temperature insensitive, and provides protection from thermal backfilling due to the large energy separation between the lower radiative state and the injector. Both properties are important in allowing higher temperature operation at longer wavelengths. Lasers using a surface plasmon based waveguide grown on a semi-insulating (SI) GaAs substrate were demonstrated at 3.4 THz in pulsed mode up to 87 K, with peak collected powers of 14 mW at 5 K, and 4 mW at 77 K.

Download or read book Molecular Beam Epitaxy written by Hajime Asahi and published by John Wiley & Sons. This book was released on 2019-04-15 with total page 510 pages. Available in PDF, EPUB and Kindle. Book excerpt: Covers both the fundamentals and the state-of-the-art technology used for MBE Written by expert researchers working on the frontlines of the field, this book covers fundamentals of Molecular Beam Epitaxy (MBE) technology and science, as well as state-of-the-art MBE technology for electronic and optoelectronic device applications. MBE applications to magnetic semiconductor materials are also included for future magnetic and spintronic device applications. Molecular Beam Epitaxy: Materials and Applications for Electronics and Optoelectronics is presented in five parts: Fundamentals of MBE; MBE technology for electronic devices application; MBE for optoelectronic devices; Magnetic semiconductors and spintronics devices; and Challenge of MBE to new materials and new researches. The book offers chapters covering the history of MBE; principles of MBE and fundamental mechanism of MBE growth; migration enhanced epitaxy and its application; quantum dot formation and selective area growth by MBE; MBE of III-nitride semiconductors for electronic devices; MBE for Tunnel-FETs; applications of III-V semiconductor quantum dots in optoelectronic devices; MBE of III-V and III-nitride heterostructures for optoelectronic devices with emission wavelengths from THz to ultraviolet; MBE of III-V semiconductors for mid-infrared photodetectors and solar cells; dilute magnetic semiconductor materials and ferromagnet/semiconductor heterostructures and their application to spintronic devices; applications of bismuth-containing III–V semiconductors in devices; MBE growth and device applications of Ga2O3; Heterovalent semiconductor structures and their device applications; and more. Includes chapters on the fundamentals of MBE Covers new challenging researches in MBE and new technologies Edited by two pioneers in the field of MBE with contributions from well-known MBE authors including three Al Cho MBE Award winners Part of the Materials for Electronic and Optoelectronic Applications series Molecular Beam Epitaxy: Materials and Applications for Electronics and Optoelectronics will appeal to graduate students, researchers in academia and industry, and others interested in the area of epitaxial growth.

Download or read book The Development and Applications of Terahertz Quantum Cascade Lasers written by Raed Hussain S. Alhathlool and published by . This book was released on 2014 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Design and Modeling of High Temperature Terahertz Quantum Cascade Lasers written by Benjamin Adams Burnett and published by . This book was released on 2016 with total page 223 pages. Available in PDF, EPUB and Kindle. Book excerpt: The portion of the electromagnetic spectrum between roughly 300 GHz and 10 THz is nicknamed the "THz Gap" because of the enormous difficulty encountered by researchers to devise practical sources covering it. Still, the quantum cascade laser (QCL) has emerged over recent years as the most promising approach to a practical source in the 1-5 THz range. First developed in the higher-frequency mid-IR, where they are now widely available, QCLs were later extended to the THz where a host of greater design challenges awaited. Lasing in QCLs is based on intersubband optical transitions in semiconductor quantum wells, the energy of which can be chosen by design ("bandstructure engineering"). However, simply building a THz optical transition is insufficient; a good design must also produce significant population inversion by the applied cascading electron current, and this requires deep understanding of the transport physics. So far, no THz QCL has operated above the temperature of 200 K, even though the reasons prohibiting high temperature operation are well known. The goal of this Thesis is to put novel ideas for high-temperature operation of THz QCL active regions through rigorous theoretical testing. The central enabling development is a density-matrix-based model of transport and optical properties tailored for use in QCLs, which is general enough that widely varying design concepts can be tested using the same core principles. Importantly, by simulating QCLs more generally, fewer a priori assumptions are required on part of the researcher, allowing for the true physics to emerge on its own. It will be shown that this gives rise to new and useful insights that will help to guide the experimental efforts towards realization of these devices. One specific application is a quantum dot cascade laser (QDCL), a highly ambitious approach in which the electrons cascade through a series of quantum dots rather than wells. Benefits are expected due to the suppression of nonradiative scattering, brought about by the discrete spectrum of electronic states. However, this in turn leads to a highly different physics of transport and effects that are not well understood, even in the case of perfect materials. This work will show that while the benefits are clear, naive scaling of existing QCL designs to the quantum dot limit will not work. An alternative strategy is given based on a revised understanding of the nature of transport, and is put to a test of practicality in which the effects of quantum dot size inhomogeneity are estimated. Another application is to the already existing method of THz difference frequency generation in mid-IR QCLs, which occurs via a difference-frequency susceptibility $\chi^{(2)}$ in the active region itself. For this purpose, the model is extended to enable a coherent and nonperturbative calculation of optical nonlinearities. First, the generality of the method is displayed through the emergence of exotic nonlinear effects, including electromagnetically-induced transparency, in mock quantum-well systems. Then, the modeling concepts are applied to the real devices, where two new and important mechanisms contributing to $\chi^{(2)}$ are identified. Most importantly, it is predicted that the QCL acts as an extremely fast photodetector of itself, giving rise to a current response to the mid-IR beatnote that provides a better path forward to the generation of frequencies below ~2 THz. Finally, the fundamentals of density matrix transport theory for QCLs are revisited to develop a model for conventional THz QCL designs eliminating the usual phenomenological treatment of scattering. The new theory is fully developed from first principles, and in particular sheds light on the effects of scattering-induced electron localization. The versatility of the model is demonstrated by successful simulation of varying active region designs.

Download or read book From High Power Terahertz Quantum Cascade Lasers to Terahertz Light Amplifiers written by Tsung-Yu Kao and published by . This book was released on 2014 with total page 208 pages. Available in PDF, EPUB and Kindle. Book excerpt: The terahertz (THz) frequency range (300 GHz to 10 THz, wavelength 30-1000 [mu]m), despite having many potential applications, is technologically relatively underdeveloped mainly because of the lack of suitable coherent radiation sources when compared with nearby electromagnetic radiation spectrum. The invention of the THz quantum cascade laser, a electronically-pumped semiconductor heterostructure which emits photons from electronic intersubband transitions, provides the first solidstate fundamental oscillator at the frequency range from 1.2 to 5.1 THz. Due to the subwavelength confinement nature of the metal-metal waveguide used in most of the THz QC lasers, far-field beam patterns from lasers with simple Fabry-Perot waveguides are divergent and far from ideal Gaussian beams. The first part of this thesis describes the development of single-mode THz QC lasers on metal-metal waveguides. Starting with the corrugated third-order DFB laser-a clever laser structure which utilizes end-fire array effect to achieve low divergence beam patterns-several applications using densely-packed third-order DFB laser arrays, such as frequency agile sources for THz swept-source optical tomography and local oscillators for THz heterodyne receivers with precise frequency control, have been investigated. With the improved design rules and fabrication techniques, 830 GHz single-mode frequency coverage on a monolithic multicolor DFB laser array has been achieved. The origin of the deterioration in far-field beam patterns and power outputs in long third-order DFB lasers is then identified. This finding leads to a modified third-order DFB laser structure which can achieve perfect phase-matching (PM) condition, resulting in scalable power output and even lower beam divergence when compared with that of a conventional third-order DFB laser. Radiations from up to 151 laser sectors are phase-locked to form a single-lobe beam pattern with divergence ~ 6 x 11° and ~13 mW pulsed power at the end-fire direction. This approach substantially increases the usable length of a third-order DFB laser while keeping a high slope efficiency (140 mW/A). Later development applies the concept of microstrip antenna-a structure commonly used in microwave engineering-to THz photonics devices. By coupling the microstrip antenna to each grating aperture of a perfectly phase-matched DFB laser, the radiation impedance of the laser can now be tuned to enhance the overall emission efficiency. This novel genre of DFB laser achieves > 8 mW pulsed power (10% duty-cycle) at 12 K with beam divergence as low as 12.5 x 12.5' and maximum lasing temperature Tmax = 109 K (pulsed) and 77 K (c.w.) with the highest slope efficiency (~450 mW/A) and wall-plug efficiency (0.57%) of all THz DFB laser sources. The second part of the thesis then focuses on the development of the first light amplifier in THz frequency under Fabry-Perot amplifier (FPA) scheme. Although amplification at terahertz frequency in quantum cascade structures has been demonstrated under the transient state or in a integrated platform, none of them is suitable for amplifying continuous-wave free-space THz radiations. The proposed amplifier is consisted of an array of short-cavity surface-emitting second-order distributed feedback lasers arranged in a two-dimensional grid which are operated marginally beneath their lasing thresholds. A overall system power gain of ~5.6x = 7.5 dB at ~3 THz is obtained with ~1 GHz bandwidth. The free-space THz light amplifier can be used as the pre-amplifier for a THz heterodyne receiver system to reduce the receiver system noise, or be placed on the focal plane of a THz imaging system to enhance the signal-to-noise ratio of the image and reduce the acquisition time. A new locking mechanism for two-dimensional phase-locked laser arrays based on antenna mutual-coupling is also proposed and then successfully demonstrated in the THz frequency using short-cavity DFB THz lasers. Up to 37 lasers are phase-locked to deliver 6.5 mW single-mode pulsed power (4% duty-cycle) at 3 THz with symmetric beam pattern ( 10 x 10°). This new coupling scheme can be extended to other electromagnetic systems with sub-wavelength confined elements such as plasmonic lasers and nanolasers. This thesis also reports the development of fabrication techniques required to bring the aforementioned novel THz cavity designs from concepts to reality which include a high aspect ratio ( 1:10) anisotropic reactive-ion etch on GaAs which is compatible with the metal-metal waveguide platform and the procedure to create airbridge structures by selectively removing the dielectric materials beneath the metal contacts.

Download or read book Terahertz Frequency Detection and Identification of Materials and Objects written by R.E. Miles and published by Springer Science & Business Media. This book was released on 2007-09-08 with total page 365 pages. Available in PDF, EPUB and Kindle. Book excerpt: Want an overview of where the technology of terahertz detection has been going? Here it is. The technology has largely been developed around expensive and bulky femtosecond laser systems but, as described in this book, advances in semiconductor superlattice technology are leading to compact "electronic" sources such as the quantum cascade laser, two-terminal "Gunn" type oscillators and even a THz frequency amplifier. These advances towards electronic (as opposed to optical) THz systems mean that the technology will become portable and much less costly.

Download or read book Terahertz Generation with Quantum Cascade Lasers written by Karun Vijayraghavan and published by . This book was released on 2014 with total page 226 pages. Available in PDF, EPUB and Kindle. Book excerpt: The terahertz (THz) spectral range is devoid of commercially feasible radiation sources, detectors, and components. In particular, THz sources are bulky, complex to operate, and cost-prohibitive - more suited for a research laboratory than a commercial setting. Developing compact and mass-producible sources in the 1 to 6 THz spectral range will open up new avenues for this technology to make a mainstream societal impact. The focus of this thesis is the development of compact, room-temperature terahertz sources based on quantum cascade lasers (QCL) and quantum well technology. QCLs are semiconductor lasers that operate with high power at mid-infrared (mid-IR) and THz frequencies. THz QCLs are the only mW-level average power sources with spectral coverage from 0.8 to 5 THz. However they only work at cryogenic temperatures because they cannot maintain population inversion across the lasing transition at elevated temperatures. Cryogenic cooling makes these sources cumbersome to operate and expensive to manufacture. Room-temperature operation significantly enhances their commercial appeal and a portion of this dissertation investigated the improvement in THz QCL temperature performance using GaAs-Al0.15Ga0.85As double-phonon resonant active region designs. These devices worked up to 173 K and were a substantial improvement compared to prior implementations of double-phonon resonant designs. Room-temperature THz sources that do not require population inversion across the lasing transition can be engineered by combining the field of nonlinear optics with intersubband transitions in quantum well structures. One method of creating inversionless THz lasing is based upon the principle of Raman gain in semiconductors and this thesis explores the design of an intersubband Raman laser (IRL) with GaAs-Al0.33Ga0.67As heterostructures. The primary focus of this dissertation is developing room-temperature, broadly-tunable, monolithic THz sources based on difference-frequency generation (DFG) in mid-IR QCLs. The source active region is quantum-engineered to provide lasing at mid-IR frequencies, [omega]1 and [omega]2, and simultaneously have giant second-order optical nonlinearity for THz generation at frequency [omega] [subscript THz]=[omega]1-[omega]2. This dissertation developed a Cherenkov emission scheme that produced devices with a narrow emission linewidth, 0.12 mW peak power and tuning from 1.55 to 5.7 THz - the largest tuning bandwidth compared to semiconductor technology of similar size and cost.

Download or read book MBE Growth Fabrication and Electrical Characterisation of Terahertz Frequency Quantum Cascade Lasers written by and published by . This book was released on 2015 with total page 302 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Development of Tunable Terahertz Quantum Cascade Wire Lasers written by Qi Qin (Ph. D.) and published by . This book was released on 2012 with total page 188 pages. Available in PDF, EPUB and Kindle. Book excerpt: For a long time, terahertz (THz) radiation has been of great interest to scientific community because of its spectroscopic and imaging applications based on its unique properties, such as the capabilities to penetrate many materials which are opaque in other frequency range (e.g. packaging, plastics, paints and semiconductors), and spectroscopic signatures of many important materials. In this thesis, a continuously tunable THz wire QC laser, which comprises a QC laser with deep sub-wavelength transverse dimensions, and a movable side object, termed as "plunger", is demonstrated. This deep sub-wavelength cross-section results in a large fraction of mode propagating outside of the laser core (GaAs/A10.15Ga0.85As material system). The frequency tuning is achieved by changing the transverse wave vector, using a plunger made by metal (metal plunger) or silicon (dielectric plunger). When nudged close to the wire laser core, the metal plunger can push modes to the opposite side of the waveguide. Confined by a metal-metal waveguide, the mode is squeezed and the transverse wave vector is increased, resulting in a blue-shifted frequency. In contrast, a silicon plunger can suck the mode out due to its similar refractive index to GaAs/Al0.15Ga0.85As material system of laser core. Thus a decreased transverse wave vector results in a redshifted frequency. Although a tuning record of 138GHz (3.6%) was achieved, a discontinuous tuning resulted from a jittering movement of the plungers due to its friction with the guiding system. To solve this problem, an improved plunger based on micro-mechanical system (MEMS) was implemented. This MEMS plunger uses a two-stage folded-beam flexure to isolate the misaligned external actuation. The plunger is attached with the flexure which suspends above a silicon substrate to eliminate friction. Eventually, this MEMS flexure was actuated by a mechanical system which comprised a lever to de-amplify the displacement of a linear mechanical feedthrough. This MEMS plunger enabled a restorable and frictionless movement which led to a continuous tuning range of 330GHz (8.6%) centered at ~3.85 THz. The challenges posted by the weak mode discrimination led to the development of comb-shape connectors which electrically connect the top metal of wire lasers and the side bonding pad. This design can significantly increase the mode discrimination by selectively guiding undesired mode into the lossy bonding pad. This robust design of single mode operation enables the initial lasing at a frequency far below the gain peak, which can potentially increase the tuning range significantly.