Download or read book Determination and Control of Contact Pressure Distribution in Fretting Fatigue written by K. Sato and published by . This book was released on 1992 with total page 16 pages. Available in PDF, EPUB and Kindle. Book excerpt: Contact pressure is one of the most important factors in fretting fatigue. The contact pressure distribution on loading of applied cyclic stress is markedly different from that on unloading. To elucidate the effect of contact pressure on fretting fatigue strength, the contact pressure distribution should be exactly determined. In this paper, the contact pressure distribution was calculated by using a boundary element method and monitored by an experimental method of caustics. Differences in the contact pressure distribution between the shapes of fretting bridges whose height is 10, 15, 20, and 30 mm at a constant span of 30 mm, and between two types of clamping, which are center clamping and edge clamping at the back face of the bridge, were analyzed. In order to examine the effect of the contact pressure distribution on the fretting fatigue strength, fretting fatigue tests in plane bending were carried out. The S-N properties obtained from fretting fatigue tests could be estimated analytically by equivalent stress amplitude.
Download or read book Standardization of Fretting Fatigue Test Methods and Equipment written by Mahmoud Helmi Attia and published by ASTM International. This book was released on 1992 with total page 275 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Mechanics of Fretting Fatigue written by D.A. Hills and published by Springer Science & Business Media. This book was released on 1994-05-31 with total page 260 pages. Available in PDF, EPUB and Kindle. Book excerpt: Failures of many mechanical components in service result from fatigue. The cracks which grow may either originate from some pre-existing macroscopic defect, or, if the component is of high integrity but highly stressed, a region of localized stress concentration. In turn, such concentrators may be caused by some minute defect, such as a tiny inclusion, or inadvertent machining damage. Another source of surface damage which may exist between notionally 'bonded' components is associated with minute relative motion along the interface, brought about usually be cyclic tangential loading. Such fretting damage is quite insidious, and may lead to many kinds of problems such as wear, but it is its influence on the promotion of embryo cracks with which we are concerned here. When the presence of fretting is associated with decreased fatigue performance the effect is known as fretting fatigue. Fretting fatigue is a subject drawing equally on materials science and applied mechanics, but it is the intention in this book to concentrate attention entirely on the latter aspects, in a search for the quantification of the influence of fretting on both crack nucleation and propagation. There have been very few previous texts in this area, and the present volume seeks to cover five principal areas; (a) The modelling of contact problems including partial slip under tangentialloading, which produces the surface damage. (b) The modelling of short cracks by rigorous methods which deal effectively with steep stress gradients, kinking and closure. (c) The experimental simulation of fretting fatigue.
Download or read book Fretting Wear and Fretting Fatigue written by Tomasz Liskiewicz and published by Elsevier. This book was released on 2022-12-07 with total page 656 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fretting Wear and Fretting Fatigue: Fundamental Principles and Applications takes a combined mechanics and materials approach, providing readers with a fundamental understanding of fretting phenomena, related modeling and experimentation techniques, methods for mitigation, and robust examples of practical applications across an array of engineering disciplines. Sections cover the underpinning theories of fretting wear and fretting fatigue, delve into experimentation and modeling methods, and cover a broad array of applications of fretting fatigue and fretting wear, looking at its impacts in medical implants, suspension ropes, bearings, heating exchangers, electrical connectors, and more. Covers theoretical fundamentals, modeling and experimentation techniques, and applications of fretting wear and fatigue Takes a combined mechanics and materials approach Discusses the differences and similarities between fretting wear and fretting fatigue as well as combined experimental and modeling methods Covers applications including medical implants, heat exchangers, bearings, automotive components, gas turbines, and more
Download or read book Fatigue and Fracture Mechanics written by Tina Louise Panontin and published by ASTM International. This book was released on 1999 with total page 922 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fretting Fatigue written by Steven E. Kinyon and published by ASTM International. This book was released on 2003 with total page 445 pages. Available in PDF, EPUB and Kindle. Book excerpt: Contains 29 contributions drawn from the Third International Symposium on Fretting Fatigue held in Nagaoka, Japan in May 2001. Sections of the volume address fretting wear and crack initiation; fretting fatigue crack and damage; life prediction; fretting fatigue parameter effects; loading condition
Download or read book Metals Abstracts written by and published by . This book was released on 1998 with total page 1076 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Contact Problems and Surface Interactions in Manufacturing and Tribological Systems written by American Society of Mechanical Engineers. Winter Annual Meeting and published by . This book was released on 1993 with total page 376 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Examination of Contact Width on Fretting Fatigue written by Russell S. Magaziner and published by . This book was released on 2002-03 with total page 186 pages. Available in PDF, EPUB and Kindle. Book excerpt: The primary goal of this study was to find the effects on the fretting fatigue life when systematically holding the fretting fatigue variables, peak contact pressure, maximum/minimum nominal bulk stress, and the ratio of shear traction to pressure force constant while varying the contact semi-width through changes in pad radius and normal load. Experimental tests were performed on a test setup capable of independent pad displacement. Analytical and finite element simulations of the different experimental tests were performed. The local mechanistic parameters were inspected. Five different critical plane based fatigue predictive parameters lacked effectiveness in predicting changes in life with changes in contact width. The Ruiz parameter, and a modified version of the Ruiz parameter performed better than the five critical plane based parameters. Correlations between slip amplitude and fretting fatigue life were found. Tests experiencing infinite fatigue life, in contrast to the typical shortened fretting fatigue life, were experiencing the gross slip condition, which led to fretting wear instead of fretting fatigue.
Download or read book Applied Mechanics Reviews written by and published by . This book was released on 1969 with total page 1090 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1992 with total page 1572 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Handbook of Contact Mechanics written by Valentin L. Popov and published by Springer. This book was released on 2019-04-26 with total page 357 pages. Available in PDF, EPUB and Kindle. Book excerpt: This open access book contains a structured collection of the complete solutions of all essential axisymmetric contact problems. Based on a systematic distinction regarding the type of contact, the regime of friction and the contact geometry, a multitude of technically relevant contact problems from mechanical engineering, the automotive industry and medical engineering are discussed. In addition to contact problems between isotropic elastic and viscoelastic media, contact problems between transversal-isotropic elastic materials and functionally graded materials are addressed, too. The optimization of the latter is a focus of current research especially in the fields of actuator technology and biomechanics. The book takes into account adhesive effects which allow access to contact-mechanical questions about micro- and nano-electromechanical systems. Solutions of the contact problems include both the relationships between the macroscopic force, displacement and contact length, as well as the stress and displacement fields at the surface and, if appropriate, within the half-space medium. Solutions are always obtained with the simplest available method - usually with the method of dimensionality reduction (MDR) or approaches which use the solution of the non-adhesive normal contact problem to solve the respective contact problem.
Download or read book Fretting Fatigue ESIS 18 written by R. B. Waterhouse and published by Wiley. This book was released on 1994-03-30 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume contains the vast majority of the papers presented at the International Conference on Fretting Fatigue in Sheffield in 1993. The book forms the latest in a series on the various aspects of fatigue, including the behaviour of short cracks and the behaviour of fatigue cracks.
Download or read book Mechanics of Elastic Contacts written by A. SACKFIELD and published by Elsevier. This book was released on 2013-10-22 with total page 505 pages. Available in PDF, EPUB and Kindle. Book excerpt: Materials and mechanical engineering researchers studying wear, fretting, elastic indentation testing and other tribological processes frequently need closed-form solutions for various attributes of contacts. These characteristics include contact law, pressure distribution, internal state of stress induced and the influence of friction. Materials and mechanical engineering researchers studying wear, fretting, elastic indentation testing and other tribological processes frequently need closed-form solutions for various attributes of contacts. These characteristics include contact law, pressure distribution, internal state of stress induced and the influence of friction. These solutions, scattered throughout the applied mechanics literature, are difficult to locate, are presented using a range of solution techniques, and express results in a way that is suitable only for experts in the field. `Mechanics of Elastic Contacts' uses a consistent set of recipes for the solution of all relevant problems, presents results in the simplest possible forms, and contains summaries using tabulated data. This reference source will provide a clear guide to elastic contacts for engineering designers, materials scientists and tribologists irrespective of their level of expertise in this important subject.
Download or read book Alloys Index written by and published by . This book was released on 1993 with total page 950 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book International Aerospace Abstracts written by and published by . This book was released on 1999 with total page 974 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Mechanics of Fretting Fatigue written by D.A. Hills and published by Springer Science & Business Media. This book was released on 2013-03-09 with total page 251 pages. Available in PDF, EPUB and Kindle. Book excerpt: Failures of many mechanical components in service result from fatigue. The cracks which grow may either originate from some pre-existing macroscopic defect, or, if the component is of high integrity but highly stressed, a region of localized stress concentration. In turn, such concentrators may be caused by some minute defect, such as a tiny inclusion, or inadvertent machining damage. Another source of surface damage which may exist between notionally 'bonded' components is associated with minute relative motion along the interface, brought about usually be cyclic tangential loading. Such fretting damage is quite insidious, and may lead to many kinds of problems such as wear, but it is its influence on the promotion of embryo cracks with which we are concerned here. When the presence of fretting is associated with decreased fatigue performance the effect is known as fretting fatigue. Fretting fatigue is a subject drawing equally on materials science and applied mechanics, but it is the intention in this book to concentrate attention entirely on the latter aspects, in a search for the quantification of the influence of fretting on both crack nucleation and propagation. There have been very few previous texts in this area, and the present volume seeks to cover five principal areas; (a) The modelling of contact problems including partial slip under tangentialloading, which produces the surface damage. (b) The modelling of short cracks by rigorous methods which deal effectively with steep stress gradients, kinking and closure. (c) The experimental simulation of fretting fatigue.
