Download or read book Design of Steel Concrete Composite Structures Using High Strength Materials written by J.Y. Richard Liew and published by Woodhead Publishing. This book was released on 2021-08-04 with total page 256 pages. Available in PDF, EPUB and Kindle. Book excerpt: High-strength materials offer alternatives to frequently used materials for high-rise construction. A material of higher strength means a smaller member size is required to resist the design load. However, high-strength concrete is brittle, and high-strength thin steel plates are prone to local buckling. A solution to overcome such problems is to adopt a steel-concrete composite design in which concrete provides lateral restraint to steel plates against local buckling, and steel plates provide confinement to high-strength concrete. Design of Steel-Concrete Composite Structures Using High Strength Materials provides guidance on the design of composite steel-concrete structures using combined high-strength concretes and steels. The book includes a database of over 2,500 test results on composite columns to evaluate design methods, and presents calculations to determine critical parameters affecting the strength and ductility of high-strength composite columns. Finally, the book proposes design methods for axial-moment interaction curves in composite columns. This allows a unified approach to the design of columns with normal- and high-strength steel concrete materials. This book offers civil engineers, structural engineers, and researchers studying the mechanical performance of composite structures in the use of high-strength materials to design and construct advanced tall buildings. Presents the design and construction of composite structures using high-strength concrete and high-strength steel, complementing and extending Eurocode 4 standards Addresses a gap in design codes in the USA, China, Europe and Japan to cover composite structures using high-strength concrete and steel in a comprehensive way Gives insight into the design of concrete-filled steel tubes and concrete-encased steel members Suggests a unified approach to designing columns with normal- and high-strength steel and concrete

Download or read book Composite Structures of Steel and Concrete written by Roger P. Johnson and published by John Wiley & Sons. This book was released on 2018-08-21 with total page 288 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides an introduction to the theory and design of composite structures of steel and concrete. Material applicable to both buildings and bridges is included, with more detailed information relating to structures for buildings. Throughout, the design methods are illustrated by calculations in accordance with the Eurocode for composite structures, EN 1994, Part 1-1, ‘General rules and rules for buildings’ and Part 1-2, ‘Structural fire design’, and their cross-references to ENs 1990 to 1993. The methods are stated and explained, so that no reference to Eurocodes is needed. The use of Eurocodes has been required in the UK since 2010 for building and bridge structures that are publicly funded. Their first major revision began in 2015, with the new versions due in the early 2020s. Both authors are involved in the work on Eurocode 4. They explain the expected additions and changes, and their effect in the worked examples for a multi-storey framed structure for a building, including resistance to fire. The book will be of interest to undergraduate and postgraduate students, their lecturers and supervisors, and to practising engineers seeking familiarity with composite structures, the Eurocodes, and their ongoing revision.

Download or read book Steel Concrete Composite Structures written by R. Narayanan and published by CRC Press. This book was released on 1988-12-31 with total page 362 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is a collection of ten extensive review chapters by different authors.

Download or read book Design of High Strength Steel Reinforced Concrete Columns written by Sing-Ping Chiew and published by CRC Press. This book was released on 2018-04-17 with total page 104 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is the companion volume to Design Examples for High Strength Steel Reinforced Concrete Columns – A Eurocode 4 Approach. Guidance is much needed on the design of high strength steel reinforced concrete (SRC) columns beyond the remit of Eurocode 4. Given the much narrower range of permitted concrete and steel material strengths in comparison to EC2 and EC3, and the better ductility and buckling resistance of SRC columns compared to steel or reinforced concrete, there is a clear need for design beyond the guidelines. This book looks at the design of SRC columns using high strength concrete, high strength structural steel and high strength reinforcing steel materials – columns with concrete cylinder strength up to 90 N/mm2, yield strength of structural steel up to 690 N/mm2 and yield strength of reinforcing steel up to 600 N/mm2 respectively. The companion volume provides detailed worked examples on use of these high strength materials. This book is written primarily for structural engineers and designers who are familiar with basic EC4 design, and should also be useful to civil engineering undergraduate and graduate students who are studying composite steel concrete design and construction. Equations for design resistances are presented clearly so that they can be easily programmed into design spreadsheets for ease of use.

Download or read book Advances in Steel Concrete Composite Structures written by J. Y. Richard Liew and published by Research Publishing Service. This book was released on 2012 with total page 31 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Composite Construction in Steel and Concrete VI written by Roberto T. Leon and published by Amer Society of Civil Engineers. This book was released on 2011 with total page 790 pages. Available in PDF, EPUB and Kindle. Book excerpt: Proceedings of the sixth International Conference on Composite Construction in Steel and Concrete held at the Devil s Thumb Ranch in Tabernash, Colorado, July 20 24, 2008. Sponsored by Engineering Conferences International; the Structural Engineering Institute of ASCE. This collection contains the 63 technical papers representing the state-of-the-art in composite construction worldwide. Topics include: composite bridges, composite slabs, shear connectors, composite columns, innovative composite structural systems, fire and seismic resistance of composite structural systems and practical applications. These papers will be valuable to structural engineers and allied professionals engaged in construction with steel and concrete composites.

Download or read book Analysis and Design of Steel and Composite Structures written by Qing Quan Liang and published by CRC Press. This book was released on 2018-10-08 with total page 458 pages. Available in PDF, EPUB and Kindle. Book excerpt: Steel and composite steel–concrete structures are widely used in modern bridges, buildings, sport stadia, towers, and offshore structures. Analysis and Design of Steel and Composite Structures offers a comprehensive introduction to the analysis and design of both steel and composite structures. It describes the fundamental behavior of steel and composite members and structures, as well as the current design criteria and procedures given in Australian standards AS/NZS 1170, AS 4100, AS 2327.1, Eurocode 4, and AISC-LRFD specifications. Featuring numerous step-by-step examples that clearly illustrate the detailed analysis and design of steel and composite members and connections, this practical and easy-to-understand text: Covers plates, members, connections, beams, frames, slabs, columns, and beam-columns Considers bending, axial load, compression, tension, and design for strength and serviceability Incorporates the author’s latest research on composite members Analysis and Design of Steel and Composite Structures is an essential course textbook on steel and composite structures for undergraduate and graduate students of structural and civil engineering, and an indispensable resource for practising structural and civil engineers and academic researchers. It provides a sound understanding of the behavior of structural members and systems.

Download or read book Design of High performance Pre engineered Steel Concrete Composite Beams for Sustainable Construction written by Ming-Shan Zhao and published by CRC Press. This book was released on 2024-08-05 with total page 144 pages. Available in PDF, EPUB and Kindle. Book excerpt: This accessible and practical shortform book details the properties and advantages of high-performance pre-engineered steel-concrete composite beams (HPCBs) for improving the sustainability of construction techniques. It also explains the analysis methods for testing HPCB systems. The authors describe a new HPCB system that has been developed to reduce the input of raw materials and embodied CO2 commonly associated with heavily loaded and long-spanned industrial buildings (which predominately comprise reinforced concrete) and improve the sustainability of the construction process. They provide several resources throughout to facilitate adoption by professionals. Design equations derived from Eurocode 4 approach for ultimate limit state and serviceability limit state and worked examples are included throughout. The authors discuss the feasibility for both materials and the full-scale beams and CO2 reduction methods, including use of recycled concrete aggregate, ground granulated blast-furnace and silica fume to replace natural coarse aggregates and Ordinary Portland Cement. Guidance for testing HPCBs—including setup, test procedure and data collection and interpretation—is also given. The authors also elaborate on recommendations for finite element analysis for HPCBs. Design examples are appended to illustrate typical current practice using a 12 × 12 m grid floor with live load of 15 kPa. Various considerations for different parameters such as fire resistance are discussed. Finally, the authors present a case study of a recently completed industrial building in Singapore to quantify the benefits of using HPCBs over reinforced concrete and conventional composite construction. Structural engineering professionals, whose work relates to long-span and heavy-loading industrial or commercial buildings, will benefit from the detailed guidance and focus on practical applications provided throughout this book. Post-graduate students of advanced steel and composite structures will also benefit from these descriptions.

Download or read book Design of Concrete Structures Using High strength Steel Reinforcement written by Bahram M. Shahrooz and published by Transportation Research Board. This book was released on 2011 with total page 83 pages. Available in PDF, EPUB and Kindle. Book excerpt: TRB's National Cooperative Highway Research Program (NCHRP) Report 679: Design of Concrete Structures Using High-Strength Steel Reinforcement evaluates the existing American Association of State Highway and Transportation Officials (AASHTO) Load and Resistance Factor Design (LRFD) Bridge Design Specifications relevant to the use of high-strength reinforcing steel and other grades of reinforcing steel having no discernible yield plateau. The report also includes recommended language to the AASHTO LRFD Bridge Design Specifications that will permit the use of high-strength reinforcing steel with specified yield strengths not greater than 100 ksi. The Appendixes to NCHRP Report 679 were published online.

Download or read book Design of Composite Steel concrete Structures written by Lloyd C. P. Yam and published by . This book was released on 1981 with total page 192 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Composite Construction in Steel and Concrete IV written by Jerome F. Hajjar and published by . This book was released on 2002 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This collection contains 85 papers presented at the Composite Construction in Steel and Concrete IV Conference, held in Banff, Alberta, Canada, May 28-June 2, 2000.

Download or read book Design Examples for High Strength Steel Reinforced Concrete Columns written by Sing-Ping Chiew and published by CRC Press. This book was released on 2018-04-17 with total page 96 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is the companion volume to Design of High Strength Steel Reinforced Concrete Columns – A Eurocode 4 Approach. This book provides a large number of worked examples for the design of high strength steel reinforced concrete (SRC) columns. It is based on the Eurocode 4 approach, but goes beyond this to give much needed guidance on the narrower range of permitted concrete and steel material strengths in comparison to EC2 and EC3, and the better ductility and buckling resistance of SRC columns compared to steel or reinforced concrete. Special considerations are given to resistance calculations that maximize the full strength of the materials, with concrete cylinder strength up to 90 N/mm2, yield strength of structural steel up to 690 N/mm2 and yield strength of reinforcing steel up to 600 N/mm2 respectively. These examples build on the design principles set out in the companion volume, allowing the readers to practice and understand the EC4 methodology easily. Structural engineers and designers who are familiar with basic EC4 design should find these design examples particularly helpful, whilst engineering undergraduate and graduate students who are studying composite steel concrete design and construction should easily gain further understanding from working through the worked examples which are set out in a step-by-step clearly fashion.

Download or read book Finite Element Analysis and Design of Steel and Steel Concrete Composite Bridges written by Ehab Ellobody and published by Butterworth-Heinemann. This book was released on 2014-05-30 with total page 683 pages. Available in PDF, EPUB and Kindle. Book excerpt: In recent years, bridge engineers and researchers are increasingly turning to the finite element method for the design of Steel and Steel-Concrete Composite Bridges. However, the complexity of the method has made the transition slow. Based on twenty years of experience, Finite Element Analysis and Design of Steel and Steel-Concrete Composite Bridges provides structural engineers and researchers with detailed modeling techniques for creating robust design models. The book’s seven chapters begin with an overview of the various forms of modern steel and steel–concrete composite bridges as well as current design codes. This is followed by self-contained chapters concerning: nonlinear material behavior of the bridge components, applied loads and stability of steel and steel–concrete composite bridges, and design of steel and steel–concrete composite bridge components. Constitutive models for construction materials including material non-linearity and geometric non-linearity The mechanical approach including problem setup, strain energy, external energy and potential energy), mathematics behind the method Commonly available finite elements codes for the design of steel bridges Explains how the design information from Finite Element Analysis is incorporated into Building information models to obtain quantity information, cost analysis

Download or read book Composite Structures of Steel and Concrete written by R. P. Johnson and published by John Wiley & Sons. This book was released on 2008-04-15 with total page 251 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book sets out the basic principles of composite constructionwith reference to beams, slabs, columns and frames, and theirapplications to building structures. It deals with the problemslikely to arise in the design of composite members in buildings,and relates basic theory to the design approach of Eurocodes 2, 3and 4. The new edition is based for the first time on the finalisedEurocode for steel/concrete composite structures.

Download or read book Composite Steel and Concrete Structures Fundamental Behaviour Second Edition written by D.J. Oehlers and published by Elsevier. This book was released on 2013-10-22 with total page 588 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book deals with the analysis and behaviour of composite structural members that are made by joining a steel component to a concrete component. The emphasis of the book is to impart a fundamental understanding of how composite structures work, so engineers develop a feel for the behaviour of the structure, often missing when design is based solely by using codes of practice or by the direct application of prescribed equations. It is not the object to provide quick design procedures for composite members, as these are more than adequately covered by recourse to such aids as safe load tables. The subject should therefore be of interest to practising engineers, particularly if they are involved in the design of non-standard or unusual composite structures for buildings and bridges, or are involved in assessing, upgrading, strengthening or repairing existing composite structures. The fundamentals in composite construction are covered first, followed by more advanced topics that include: behaviour of mechanical and rib shear connectors; local buckling; beams with few shear connectors; moment redistribution and lateral-distortional buckling in continuous beams; longitudinal splitting; composite beams with service ducts; composite profiled beams and profiled slabs; composite columns; and the fatigue design and assessment of composite bridge beams.

Download or read book Composite Construction in Steel and Concrete 9 written by Markus Knobloch and published by John Wiley & Sons. This book was released on 2024-09-03 with total page 754 pages. Available in PDF, EPUB and Kindle. Book excerpt: Composite Construction in Steel and Concrete IX The highly successful International Conference series on Composite Construction in Steel and Concrete is a major forum for researchers, practitioners, and engineers to share and discuss their research, practical experience and innovations related to composite constructions in steel and concrete. Composite Construction is a key consideration in the design of buildings and infrastructure. Significant advances in research and development have increased the knowledge of the structural performance of composite structures. Some areas are becoming well understood and implemented in the design practice, codes and standards worldwide, while others like, e.g., application of high-performance materials or dismountable and reusable composite members need further studies; trends that are reflected by the conference papers. The 62 contributions contained in this book cover a wide variety of topics, including composite beams, composite columns, composite decks, joints, shear connections, fire behavior, seismic behavior, fatigue and fracture, codification, composite bridges, innovative hybrid structures, numerical investigations and practical applications. The Papers are peer-reviewed by the Scientific Board and may be adapted based on the outcome of the discussions during the conference. This book therefore summarizes the state-of-the-art in composite construction worldwide, as presented at the 9th International Conference on Composite Construction in Steel and Concrete hosted by the Ruhr-Universität Bochum, University of Stuttgart, RPTU Kaiserslautern-Landau and University of Luxembourg, representing the work of authors from 18 countries.

Download or read book Analysis and Design of Steel and Composite Structures written by Qing Quan Liang and published by CRC Press. This book was released on 2014-10-21 with total page 460 pages. Available in PDF, EPUB and Kindle. Book excerpt: Steel and composite steel–concrete structures are widely used in modern bridges, buildings, sport stadia, towers, and offshore structures. Analysis and Design of Steel and Composite Structures offers a comprehensive introduction to the analysis and design of both steel and composite structures. It describes the fundamental behavior of steel and composite members and structures, as well as the current design criteria and procedures given in Australian standards AS/NZS 1170, AS 4100, AS 2327.1, Eurocode 4, and AISC-LRFD specifications. Featuring numerous step-by-step examples that clearly illustrate the detailed analysis and design of steel and composite members and connections, this practical and easy-to-understand text: Covers plates, members, connections, beams, frames, slabs, columns, and beam-columns Considers bending, axial load, compression, tension, and design for strength and serviceability Incorporates the author’s latest research on composite members Analysis and Design of Steel and Composite Structures is an essential course textbook on steel and composite structures for undergraduate and graduate students of structural and civil engineering, and an indispensable resource for practising structural and civil engineers and academic researchers. It provides a sound understanding of the behavior of structural members and systems.