EBookClubs

Read Books & Download eBooks Full Online

EBookClubs

Read Books & Download eBooks Full Online

Book Seismic Design of Precast Concrete Building Structures

Download or read book Seismic Design of Precast Concrete Building Structures written by fib Fédération internationale du béton and published by fib Fédération internationale du béton. This book was released on 2003-01-01 with total page 272 pages. Available in PDF, EPUB and Kindle. Book excerpt: The aim of this state-of-art report is to present current practices for use of precast and prestressed concrete in countries in seismic regions, to recommend good practice, and to discuss current developments. The report has been drafted by 30 contributors from nine different countries. This state-of-art report covers: state of the practice in various countries; advantages and disadvantages of incorporating precast reinforced and prestressed concrete in construction; lessons learned from previous earthquakes; construction concepts; design approaches; primary lateral load resisting systems (precast and prestressed concrete frame systems and structural walls including dual systems) diaphragms of precast and prestressed concrete floor units; modelling and analytical methods; gravity load resisting systems; foundations; and miscellaneous elements (shells, folded plates, stairs and architectural cladding panels). Design equations are reported where necessary, but the emphasis is on principles. Ordinary cast-in-place reinforced concrete is not considered in this report. This fib state-of-the-art report is intended to assist designers and constructors to provide safe and economical applications of structural precast concrete and at the same time to allow innovation in design and construction to continue. This Bulletin N° 27 was approved as an fib state-of-art report in autumn 2002 byfib Commission 7, Seismic design.

Book Precast concrete buildings in seismic areas

Download or read book Precast concrete buildings in seismic areas written by FIB – Féd. Int. du Béton and published by FIB - Féd. Int. du Béton. This book was released on 2016 with total page 290 pages. Available in PDF, EPUB and Kindle. Book excerpt: This document has a broad scope and is not focussed on design issues. Precast construction under seismic conditions is treated as a whole. The main principles of seismic design of different structural systems, their behavior and their construction techniques are presented through rules, construction steps and sequences, procedures, and details that should lead to precast structures built in seismic areas complying with the fundamental performance requirements of collapse prevention and life safety in major earthquakes and limited damage in more frequent earthquakes. The content of this document is largely limited to conventional precast construction and, although some information is provided on the well-known “PRESSS technology” (jointed ductile dry connections), this latter solution is not treated in detail in this document. The general overview, contained in this document, of alternative structural systems and connection solutions available to achieve desired performance levels, intends to provide engineers, architects, clients, and end-users (in general) with a better appreciation of the wide range of applications that modern precast concrete technology can have in various types of construction from industrial to commercial as well as residential. Lastly, the emphasis on practical aspects, from conceptual design to connection detailing, aims to help engineers to move away from the habit of blindly following prescriptive codes in their design, but instead go back to basic principles, in order to achieve a more robust understanding, and thus control, of the seismic behaviour of the structural system as a whole, as well as of its components and individual connections.

Book Concrete Structures in Earthquake Regions

Download or read book Concrete Structures in Earthquake Regions written by Edmund D. Booth and published by Longman Scientific and Technical. This book was released on 1994 with total page 392 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is an essential reference for practicing civil and structural engineers and architects involved with projects in earthquake regions. Undergraduate and advanced students of earthquake engineering will welcome the comprehensive and approachable coverage.

Book The Shock and Vibration Digest

Download or read book The Shock and Vibration Digest written by and published by . This book was released on 1986 with total page 594 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Book Concrete Buildings in Seismic Regions

Download or read book Concrete Buildings in Seismic Regions written by George G. Penelis and published by CRC Press. This book was released on 2014-03-24 with total page 856 pages. Available in PDF, EPUB and Kindle. Book excerpt: Bearing in mind that reinforced concrete is a key component in a majority of built environment structures, Concrete Buildings in Seismic Regions combines the scientific knowledge of earthquake engineering with a focus on the design of reinforced concrete buildings in seismic regions. This book addresses practical design issues, providing an integrated, comprehensible, and clear presentation that is suitable for design practice. It combines current approaches to seismic analysis and design, with a particular focus on reinforced concrete structures, and includes: an overview of structural dynamics analysis and design of new R/C buildings in seismic regions post-earthquake damage evaluation, pre earthquake assessment of buildings and retrofitting procedures seismic risk management of R/C buildings within urban nuclei extended numerical example applications Concrete Buildings in Seismic Regions determines guidelines for the proper structural system for many types of buildings, explores recent developments, and covers the last two decades of analysis, design, and earthquake engineering. Divided into three parts, the book specifically addresses seismic demand issues and the basic issues of structural dynamics, considers the "capacity" of structural systems to withstand seismic effects in terms of strength and deformation, and highlights existing R/C buildings under seismic action. All of the book material has been adjusted to fit a modern seismic code and offers in-depth knowledge of the background upon which the code rules are based. It complies with the last edition of European Codes of Practice for R/C buildings in seismic regions, and includes references to the American Standards in effect for seismic design.

Book Design of Reinforced Concrete Buildings for Seismic Performance

Download or read book Design of Reinforced Concrete Buildings for Seismic Performance written by Mark Aschheim and published by CRC Press. This book was released on 2019-04-05 with total page 622 pages. Available in PDF, EPUB and Kindle. Book excerpt: The costs of inadequate earthquake engineering are huge, especially for reinforced concrete buildings. This book presents the principles of earthquake-resistant structural engineering, and uses the latest tools and techniques to give practical design guidance to address single or multiple seismic performance levels. It presents an elegant, simple and theoretically coherent design framework. Required strength is determined on the basis of an estimated yield displacement and desired limits of system ductility and drift demands. A simple deterministic approach is presented along with its elaboration into a probabilistic treatment that allows for design to limit annual probabilities of failure. The design method allows the seismic force resisting system to be designed on the basis of elastic analysis results, while nonlinear analysis is used for performance verification. Detailing requirements of ACI 318 and Eurocode 8 are presented. Students will benefit from the coverage of seismology, structural dynamics, reinforced concrete, and capacity design approaches, which allows the book to be used as a foundation text in earthquake engineering.

Book Displacement based Seismic Design of Reinforced Concrete Buildings

Download or read book Displacement based Seismic Design of Reinforced Concrete Buildings written by fib Fédération internationale du béton and published by fib Fédération internationale du béton. This book was released on 2003 with total page 206 pages. Available in PDF, EPUB and Kindle. Book excerpt: A brief summary of the history of seismic design as given in chapter 1, indicates that initially design was purely based on strength or force considerations. When the importance of displacement, however, became better appreciated, it was attempted to modify the existing force-based approach in order to include considerations of displacement, rather than to totally reconsider the procedure on a more rational basis. In the last decade, then, several researchers started pointing out this inconsistency, proposing displacement-based approaches for earthquake engineering evaluation and design, with the aim of providing improved reliability in the engineering process by more directly relating computed response and expected structural performance. The main objective of this report is to summarize, critically review and compare the displacement - based approaches proposed in the literature, thus favouring code implementation and practical use of rational and reliable methods. Chapter 2 Seismic performance and design objectives of this report introduces concepts of performance levels, seismic hazard representation, and the coupling of performance and hazard to define performance objectives. In fact, for displacement analysis to be relevant in the context of performance-based design, the structural engineer must select appropriate performance levels and seismic loadings. A critical review of some engineering limit states appropriate to the different performance levels is therefore proposed. In chapter 3 Conceptual basis for displacement-based earthquake resistant design, the fundamental principles associated with displacement of the ground during an earthquake and the effects, in terms of displacement, in the structure, are reviewed. The historical development guides the presentation with a review of general linear and nonlinear structural dynamics principles, general approaches to estimate displacement, for both ground and structure, and finally a general presentation of the means to measure and judge the appropriateness of the displacements of the structure in section. Chapter 4 Approaches and procedures for displacement-based design can be somehow considered the fundamental part of the report, since a critical summary of the displacement - based approaches proposed by different researchers is presented there. Displacement - based design may require specific characterization of the input ground motion, a topic addressed in Chapter 5 Seismic input. In general, various pertinent definitions of input motion for non-code format analysis are included, while peak ground parameters necessary for code base shear equations are only addressed as needed for the definition of motion for analysis. Chapter 6 Displacement capacity of members and systems addresses the fundamental problem of evaluating the inelastic displacement capacity of reinforced concrete members and realistic values of their effective cracked stiffness at yielding, including effects of shear and inclined cracking, anchorage slip, bar buckling and of load cycling. In Chapter 7 Application and evaluation of displacement-based approaches, some of the many different displacement based design procedures briefly introduced in Chapter 4 are applied to various case studies, identifying and discussing the difficulties a designer may encounter when trying to use displacement based design. Results for five different case studies designed in accordance with eight different displacement based design methods are presented. Although in general case studies are considered a useful but marginal part of a state of the art document, in this case it has to be noted that chapter 7 is possibly the most innovative and fundamental part of the whole report. The conclusions of chapter 7 are the fundamental and essential conclusions of the document and allow foreseeing a bright future for displacement - based design approaches. The state-of-art report has been elaborated over a period of 4 years by Task Group 7.2 Displacement-based design and assessment of fib Commission 7Seismic design, a truly international team of experts, representing the expertise and experience of all the important seismic regions of the world. In October 2002 the final draft of the Bulletin was presented to the public during the 1st fibCongress in Osaka. It was also there that it was approved by fib Commission 7Seismic Design.

Book 1st fib Congress in Osaka Japan Vol1

Download or read book 1st fib Congress in Osaka Japan Vol1 written by FIB – International Federation for Structural Concrete and published by FIB - Féd. Int. du Béton. This book was released on 2002-01-01 with total page 817 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Book Structural Connections for Precast Concrete Buildings

Download or read book Structural Connections for Precast Concrete Buildings written by fib Fédération internationale du béton and published by fib Fédération internationale du béton. This book was released on 2008-01-01 with total page 369 pages. Available in PDF, EPUB and Kindle. Book excerpt: Connections are among the most essential parts in precast structures. Their performance relates to the structural limit states, as well as to manufacture of the precast elements and erection and maintenance of the structure itself. Proper design of connections is one major key to a successful prefabrication. The principal aim of fib Bulletin 43 is to encourage good practice in the design of structural connections in precast concrete structures. This is achieved through a good understanding of structural connections as parts of the overall structural system and of basic force transferring mechanisms. The bulletin consists of two parts; the first part concerns general considerations and philosophy in the design of structural connections, and the second part deals with basic force transferring mechanisms within structural connections. The main focus is on the design of structural connections with regard to their structural function in ordinary design situations in the serviceability and ultimate limit states, and in accidental/abnormal design situations, like fire, lack of fit and impact/accidental loads. Other aspects considered include production, handling and site erection of elements, building physics, durability and maintenance. Bulletin 43 applies to structural connections for precast concrete buildings, although the information on basic force transfer mechanisms can also be applicable to other types of prefabricated structures.

Book Earthquake Design Practice for Buildings

Download or read book Earthquake Design Practice for Buildings written by David Key and published by Thomas Telford. This book was released on 1988 with total page 236 pages. Available in PDF, EPUB and Kindle. Book excerpt: Illustrated and with a large number of photographs, diagrams and graphs, this title is a sound guide not only to the practising engineer who is unfamiliar with the concepts of seismic design but also to those familiar with the concepts but who want a concise design guide to what is sound engineering practice.

Book Concrete Buildings in Seismic Regions Second Edition

Download or read book Concrete Buildings in Seismic Regions Second Edition written by George G. Penelis and published by CRC Press. This book was released on 2018-10-25 with total page 801 pages. Available in PDF, EPUB and Kindle. Book excerpt: Reinforced concrete (R/C) is one of the main building materials used worldwide, and an understanding of its structural performance under gravity and seismic loads, albeit complex, is crucial for the design of cost effective and safe buildings. Concrete Buildings in Seismic Regions comprehensively covers of all the analysis and design issues related to the design of reinforced concrete buildings under seismic action. It is suitable as a reference to the structural engineer dealing with specific problems during the design process and also for undergraduate and graduate structural, concrete and earthquake engineering courses. This revised edition provides new and significantly developed coverage of seismic isolation and passive devices, and coverage of recent code modifications as well as notes on future developments of standards. It retains an overview of structural dynamics, the analysis and design of new R/C buildings in seismic regions, post-earthquake damage evaluation, pre-earthquake assessment of buildings and retrofitting procedures, and several numerical examples. The book outlines appropriate structural systems for many types of buildings, explores recent developments, and covers the last two decades of analysis, design, and earthquake engineering. It specifically addresses seismic demand issues and the basic issues of structural dynamics, considers the "capacity" of structural systems to withstand seismic effects in terms of strength and deformation, and highlights the assessment of existing R/C buildings under seismic action. All of the material has been developed to fit a modern seismic code and offers in-depth knowledge of the background upon which the code rules are based. It complies with European Codes of Practice for R/C buildings in seismic regions, and includes references to current American Standards for seismic design.

Book PCI Journal

Download or read book PCI Journal written by and published by . This book was released on 2007 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Book Dynamic Behaviour of Reinforced Concrete Frames Designed with Direct Displacement Based Design

Download or read book Dynamic Behaviour of Reinforced Concrete Frames Designed with Direct Displacement Based Design written by J. Didier Pettinga and published by . This book was released on 2005 with total page 154 pages. Available in PDF, EPUB and Kindle. Book excerpt: