Download or read book Design of an RF CMOS Power Amplifier for Wireless Sensor Networks written by Hua Pan and published by . This book was released on 2012 with total page 194 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Power Amplifier (PA) is the last Radio Frequency (RF) building block in a transmitter, directly driving an antenna. The low power RF input signal of the PA is amplified to a significant power RF output signal by converting DC power into RF power. Since the PA consumes a majority of the power, efficiency plays one of the most important roles in a PA design. Designing an efficient, fully integrated RF PA that can operate at low supply voltage (1.2V), low power, and low RF frequency (433MHz) is a major challenge. The class E Power Amplifier, which is one type of switch mode PA, is preferred in such a scenario because of its higher theoretical efficiency compared to linear power amplifiers. A controllable class E RF power amplifier design implemented in 0.13 microm CMOS process is presented. The circuit was designed, simulated, laid out, fabricated, and tested. The PA will be integrated as a part of a complete wireless transceiver system using the same process

Download or read book RF CMOS Power Amplifiers Theory Design and Implementation written by Mona M. Hella and published by Springer Science & Business Media. This book was released on 2005-12-27 with total page 107 pages. Available in PDF, EPUB and Kindle. Book excerpt: RF CMOS Power Amplifiers: Theory Design and Implementation focuses on the design procedure and the testing issues of CMOS RF power amplifiers. This is the first monograph addressing RF CMOS power amplifier design for emerging wireless standards. The focus on power amplifiers for short is distance wireless personal and local area networks (PAN and LAN), however the design techniques are also applicable to emerging wide area networks (WAN) infrastructure using micro or pico cell networks. The book discusses CMOS power amplifier design principles and theory and describes the architectures and tardeoffs in designing linear and nonlinear power amplifiers. It then details design examples of RF CMOS power amplifiers for short distance wireless applications (e, g., Bluetooth, WLAN) including designs for multi-standard platforms. Design aspects of RF circuits in deep submicron CMOS are also discussed. RF CMOS Power Amplifiers: Theory Design and Implementation serves as a reference for RF IC design engineers and RD and R&D managers in industry, and for graduate students conducting research in wireless semiconductor IC design in general and with CMOS technology in particular.

Download or read book Linear CMOS RF Power Amplifiers for Wireless Applications written by Paulo Augusto Dal Fabbro and published by Springer Science & Business Media. This book was released on 2010-06-22 with total page 171 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advances in electronics have pushed mankind to create devices, ranging from - credible gadgets to medical equipment to spacecraft instruments. More than that, modern society is getting used to—if not dependent on—the comfort, solutions, and astonishing amount of information brought by these devices. One ?eld that has continuously bene?tted from those advances is the radio frequency integrated c- cuit (RFIC) design, which in its turn has promoted countless bene?ts to the mankind as a payback. Wireless communications is one prominent example of what the - vances in electronics have enabled and their consequences to our daily life. How could anyone back in the eighties think of the possibilities opened by the wireless local area networks (WLANs) that can be found today in a host of places, such as public libraries, coffee shops, trains, to name just a few? How can a youngster, who lives this true WLAN experience nowadays, imagine a world without it? This book dealswith the design oflinearCMOS RF PowerAmpli?ers(PAs). The RF PA is a very important part of the RF transceiver, the device that enables wireless communications. Two important aspects that are key to keep the advances in RF PA design at an accelerate pace are treated: ef?ciency enhancement and frequen- tunable capability. For this purpose, the design of two different integrated circuits realizedina0. 11μmtechnologyispresented,eachoneaddressingadifferentaspect. With respect to ef?ciency enhancement, the design of a dynamic supply RF power ampli?er is treated, making up the material of Chaps. 2 to 4.

Download or read book Wireless Power Transmission for Sustainable Electronics written by Nuno Borges Carvalho and published by John Wiley & Sons. This book was released on 2020-02-19 with total page 432 pages. Available in PDF, EPUB and Kindle. Book excerpt: Provides a collection of works produced by COST Action IC1301 with the goal of achieving significant advances in the field of wireless power transmission This book constitutes together information from COST Action IC1301, a group of academic and industry experts seeking to align research efforts in the field of wireless power transmission (WPT). It begins with a discussion of backscatter as a solution for Internet of Things (IoT) devices and goes on to describe ambient backscattering sensors that use FM broadcasting for low cost and low power wireless applications. The book also explores localization of passive RFID tags and augmented tags using nonlinearities of RFID chips. It concludes with a review of methods of electromagnetic characterization of textile materials for the development of wearable antennas. Wireless Power Transmission for Sustainable Electronics: COST WiPE - IC1301 covers textile-supported wireless energy transfer, and reviews methods for the electromagnetic characterization of textile materials for the development of wearable antennas. It also looks at: backscatter RFID sensor systems for remote health monitoring; simultaneous localization (of robots and objects) and mapping (SLAM); autonomous system of wireless power distribution for static and moving nodes of wireless sensor networks; and more. Presents techniques for smart beam-forming for "on demand" wireless power transmission (WPT) Discusses RF and microwave energy harvesting for space applications Describes miniaturized RFID transponders for object identification and sensing Wireless Power Transmission for Sustainable Electronics: COST WiPE - IC1301 is an excellent book for both graduate students and industry engineers involved in wireless communications and power transfer, and sustainable materials for those fields.

Download or read book High Linearity CMOS RF Front End Circuits written by Yongwang Ding and published by Springer Science & Business Media. This book was released on 2006-02-08 with total page 132 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on high performance radio frequency integrated circuits (RF IC) design in CMOS. 1. Development of radio frequency ICs Wireless communications has been advancing rapidly in the past two decades. Many high performance systems have been developed, such as cellular systems (AMPS, GSM, TDMA, CDMA, W-CDMA, etc. ), GPS system (global po- tioning system) and WLAN (wireless local area network) systems. The rapid growth of VLSI technology in both digital circuits and analog circuits provides benefits for wireless communication systems. Twenty years ago not many p- ple could imagine millions of transistors in a single chip or a complete radio for size of a penny. Now not only complete radios have been put in a single chip, but also more and more functions have been realized by a single chip and at a much lower price. A radio transmits and receives electro-magnetic signals through the air. The signals are usually transmitted on high frequency carriers. For example, a t- ical voice signal requires only 30 Kilohertz bandwidth. When it is transmitted by a FM radio station, it is often carried by a frequency in the range of tens of megahertz to hundreds of megahertz. Usually a radio is categorized by its carrier frequency, such as 900 MHz radio or 5 GHz radio. In general, the higher the carrier frequency, the better the directivity, but the more difficult the radio design.

Download or read book Linear CMOS RF Power Amplifiers written by Hector Solar Ruiz and published by Springer Science & Business Media. This book was released on 2013-09-14 with total page 191 pages. Available in PDF, EPUB and Kindle. Book excerpt: The work establishes the design flow for the optimization of linear CMOS power amplifiers from the first steps of the design to the final IC implementation and tests. The authors also focuses on design guidelines of the inductor’s geometrical characteristics for power applications and covers their measurement and characterization. Additionally, a model is proposed which would facilitate designs in terms of transistor sizing, required inductor quality factors or minimum supply voltage. The model considers limitations that CMOS processes can impose on implementation. The book also provides different techniques and architectures that allow for optimization.

Download or read book Design and Control of RF Power Amplifiers written by Alireza Shirvani and published by Springer Science & Business Media. This book was released on 2013-04-18 with total page 157 pages. Available in PDF, EPUB and Kindle. Book excerpt: Design and Control of RF Power Amplifiers investigates various architectures and concepts for the design and control of radio-frequency (RF) power amplifiers. This book covers merits and challenges of integrating RF power amplifiers in various technologies, and introduces a number of RF power amplifier performance metrics. It provides a thorough review of various power amplifier topologies, followed by a description of approaches and architectures for the control and linearization of these amplifiers. A novel parallel amplifier architecture introduced in this book offers a breakthrough solution to enhancing efficiency in systems using power control. Design and Control of RF Power Amplifiers is a valuable resource for designers, researchers and students in the field of RF integrated circuit design. Detailed and thorough coverage of various concepts in RF power amplifier design makes this book an invaluable guide for both beginners and professionals.

Download or read book Design and Analysis of RF CMOS Power Amplifiers for Bluetooth Applications written by Ying Y. Li and published by . This book was released on 2014 with total page 128 pages. Available in PDF, EPUB and Kindle. Book excerpt: This thesis researches the design of transceiver front-end RF amplifiers for Bluetooth applications in GPDK 45 nm CMOS technology. The target of the design was to minimize the transceiver's power consumption while achieving the best device operating performances. The design of a band-pass low noise amplifier (LNA) used for the receiver and the design of a power amplifier (PA) used for the transmitter were presented. Both amplifiers were designed in 45 nm CMOS technology with a DC supply voltage under 1.2 V to meet Bluetooth specifications at 2.45 GHz operating frequency. The LNA was designed to achieve a minimum small signal gain of at least 15 dB10 with a NF less than 2 dB10 and a reasonable input range for linearity at 1 mW operating power consumption. The PA was designed based on class E switching power amplifier configuration to achieve a minimum of 40% drain efficiency for 100 mW (Bluetooth Class 1) output power. Research on low power high performance Bluetooth device front-end RF amplifiers was conducted through studies of wireless communication modulation schemes, impedance matching networks, and trade-offs between performance parameters. In summation, this thesis searched for, explored, and analyzed possible methodologies that could be used to design RF CMOS amplifiers of Bluetooth applications.

Download or read book CMOS Low Noise Amplifier Design for Wireless Sensor Networks written by Richard Lu and published by . This book was released on 2003 with total page 73 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Modeling and Design Techniques for RF Power Amplifiers written by Arvind Raghavan and published by John Wiley & Sons. This book was released on 2008-02-04 with total page 224 pages. Available in PDF, EPUB and Kindle. Book excerpt: Achieve higher levels of performance, integration, compactness, and cost-effectiveness in the design and modeling of radio-frequency (RF) power amplifiers RF power amplifiers are important components of any wireless transmitter, but are often the limiting factors in achieving better performance and lower cost in a wireless communication system—presenting the RF IC design community with many challenges. The next-generation technological advances presented in this book are the result of cutting-edge research in the area of large-signal device modeling and RF power amplifier design at the Georgia Institute of Technology, and have the potential to significantly address issues of performance and cost-effectiveness in this area. Richly complemented with hundreds of figures and equations, Modeling and Design Techniques for RF Power Amplifiers introduces and explores the most important topics related to RF power amplifier design under one concise cover. With a focus on efficiency enhancement techniques and the latest advances in the field, coverage includes: Device modeling for CAD Empirical modeling of bipolar devices Scalable modeling of RF MOSFETs Power amplifier IC design Power amplifier design in silicon Efficiency enhancement of RF power amplifiers The description of state-of-the-art techniques makes this book a valuable and handy reference for practicing engineers and researchers, while the breadth of coverage makes it an ideal text for graduate- and advanced undergraduate-level courses in the area of RF power amplifier design and modeling.

Download or read book Advances in Analog and RF IC Design for Wireless Communication Systems written by Mustafa Acar and published by Elsevier Inc. Chapters. This book was released on 2013-05-13 with total page 51 pages. Available in PDF, EPUB and Kindle. Book excerpt: This chapter presents high-efficiency power amplifiers (PAs) for wireless infrastructure. It starts by stating the importance of high efficiency and the historical evolution in base station PA concepts. It then introduces the current solution, the Doherty PA. After explaining the fundamentals of the Doherty PA, a novel implementation achieving more than 35% drain efficiency across a 6dB power back-off range and up to 20W peak power between 1.7 and 2.3GHz is given. Afterwards, a future PA concept, switch-mode outphasing PA, is introduced. Theory and implementation details of a class-E outphasing PA achieving more than 60% drain efficiency across a 6dB power back-off range and up to 19W peak power between 1800 and 2050MHz is explained. By the end of the chapter, an essential part of switch-mode PAs, high voltage (up to 10V) and high frequency (up to 4GHz) drivers are presented.

Download or read book RF and Microwave Power Amplifier Design written by Andrei Grebennikov and published by McGraw Hill Professional. This book was released on 2004-09-15 with total page 433 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is a rigorous tutorial on radio frequency and microwave power amplifier design, teaching the circuit design techniques that form the microelectronic backbones of modern wireless communications systems. Suitable for self-study, corporate training, or Senior/Graduate classroom use, the book combines analytical calculations and computer-aided design techniques to arm electronic engineers with every possible method to improve their designs and shorten their design time cycles.

Download or read book RF and mm Wave Power Generation in Silicon written by Hua Wang and published by Academic Press. This book was released on 2015-12-10 with total page 578 pages. Available in PDF, EPUB and Kindle. Book excerpt: RF and mm-Wave Power Generation in Silicon presents the challenges and solutions of designing power amplifiers at RF and mm-Wave frequencies in a silicon-based process technology. It covers practical power amplifier design methodologies, energy- and spectrum-efficient power amplifier design examples in the RF frequency for cellular and wireless connectivity applications, and power amplifier and power generation designs for enabling new communication and sensing applications in the mm-Wave and THz frequencies. With this book you will learn: Power amplifier design fundamentals and methodologies Latest advances in silicon-based RF power amplifier architectures and designs and their integration in wireless communication systems State-of-the-art mm-Wave/THz power amplifier and power generation circuits and systems in silicon Extensive coverage from fundamentals to advanced design topics, focusing on various layers of abstraction: from device modeling and circuit design strategy to advanced digital and mixed-signal architectures for highly efficient and linear power amplifiers New architectures for power amplifiers in the cellar and wireless connectivity covering detailed design methodologies and state-of-the-art performances Detailed design techniques, trade-off analysis and design examples for efficiency enhancement at power back-off and linear amplification for spectrally-efficient non-constant envelope modulations Extensive coverage of mm-Wave power-generation techniques from the early days of the 60 GHz research to current state-of the-art reconfigurable, digital mm-Wave PA architectures Detailed analysis of power generation challenges in the higher mm-Wave and THz frequencies and novel technical solutions for a wide range for potential applications, including ultrafast wireless communication to sensing, imaging and spectroscopy Contributions from the world-class experts from both academia and industry

Download or read book Ultra Low Power Wireless Technologies for Sensor Networks written by Brian Otis and published by Springer Science & Business Media. This book was released on 2007-02-24 with total page 192 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is written for academic and professional researchers designing communication systems for pervasive and low power applications. There is an introduction to wireless sensor networks, but the main emphasis of the book is on design techniques for low power, highly integrated transceivers. Instead of presenting a single design perspective, this book presents the design philosophies from three diverse research groups, providing three completely different strategies for achieving similar goals. By presenting diverse perspectives, this book prepares the reader for the countless design decisions they will be making in their own designs.

Download or read book Introduction to RF Power Amplifier Design and Simulation written by Abdullah Eroglu and published by CRC Press. This book was released on 2018-09-03 with total page 289 pages. Available in PDF, EPUB and Kindle. Book excerpt: Introduction to RF Power Amplifier Design and Simulation fills a gap in the existing literature by providing step-by-step guidance for the design of radio frequency (RF) power amplifiers, from analytical formulation to simulation, implementation, and measurement. Featuring numerous illustrations and examples of real-world engineering applications, this book: Gives an overview of intermodulation and elaborates on the difference between linear and nonlinear amplifiers Describes the high-frequency model and transient characteristics of metal–oxide–semiconductor field-effect transistors Details active device modeling techniques for transistors and parasitic extraction methods for active devices Explores network and scattering parameters, resonators, matching networks, and tools such as the Smith chart Covers power-sensing devices including four-port directional couplers and new types of reflectometers Presents RF filter designs for power amplifiers as well as application examples of special filter types Demonstrates the use of computer-aided design (CAD) tools, implementing systematic design techniques Blending theory with practice, Introduction to RF Power Amplifier Design and Simulation supplies engineers, researchers, and RF/microwave engineering students with a valuable resource for the creation of efficient, better-performing, low-profile, high-power RF amplifiers.

Download or read book Handbook of RF and Wireless Technologies written by Farid Dowla and published by Elsevier. This book was released on 2003-11-20 with total page 540 pages. Available in PDF, EPUB and Kindle. Book excerpt: Expert contributors drawn from the ranks of academia and industry have authored chapters in such areas as third-generation wireless, wireless sensor networks, RF power amplifiers, spread spectrum modulation, signal propagation, antennas, and other key subjects that engineers working in RF and wireless need to be familiar with. This is far more than just a tutorial or reference guide—it is a "guided tour" through the world of cutting-edge RF and wireless design, combining theory, applications, and philosophies behind the RF/wireless design process. The multiple and sometimes overlapping chapters reiterate and emphasize the fundamentals in the context of different types of wireless applications.Here are just a few benefits that readers will gain from reading this book:*A refresher and update of wireless principles and techniques.*Information about the latest (and forthcoming) RF and wireless circuits, products and systems.*Guidelines, approaches, and techniques to RF/wireless design.*Examples of typical applications with an emphasis on real-world situations including existing and forthcoming new components and integrated circuits.*Coverage of new and emerging wireless topics heretofore not widely covered in print (e.g. UWB, RFID, IR, etc.) * A comprehensive survey of current RF and wireless engineering practice * Heavy emphasis on practical applications and design guidelines* Multiple contributors assure a wide range of perspectives and avoids individual bias

Download or read book RF Power Amplifiers for Mobile Communications written by Patrick Reynaert and published by Springer Science & Business Media. This book was released on 2006-11-18 with total page 259 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book tackles both high efficiency and high linearity power amplifier (PA) design in low-voltage CMOS. With its emphasis on theory, design and implementation, the book offers a guide for those actively involved in the design of fully integrated CMOS wireless transceivers. Offering mathematical background, as well as intuitive insight, the book is essential reading for RF design engineers and researchers and is also suitable as a text book.