Download or read book Design of a Research Engine for Homogeneous Charge Compression Ignition HCCI Combustion written by Philip S. Zoldak and published by . This book was released on 2005 with total page 490 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Design of a Viable Homogeneous charge Compression ignition HCCI Engine written by Paul E. Yelvington and published by . This book was released on 2004 with total page 261 pages. Available in PDF, EPUB and Kindle. Book excerpt: The homogeneous-charge compression-ignition (HCCI) engine is a novel engine technology with the potential to substantially lower emissions from automotive sources. HCCI engines use lean-premixed combustion to achieve good fuel economy and low emissions of nitrogen-oxides and particulate matter. However, experimentally these engines have demonstrated a viable operating range that is too narrow for vehicular applications. Incomplete combustion or misfire can occur under fuel-lean conditions imposing a minimum load at which the engine can operate. At high loads, HCCI engines are often extremely loud and measured cylinder pressures show strong acoustic oscillations resembling those for a knocking sparkignited engine. The goal of this research was to understand the factors limiting the HCCI range of operability and propose ways of broadening that range. An engine simulation tool was developed to model the combustion process in the engine and predict HCCI knock and incomplete combustion. Predicting HCCI engine knock is particularly important because knock limits the maximum engine torque, and this limitation is a major obstacle to commercialization. A fundamentally-based criterion was developed and shown to give good predictions of the experimental knock limit. Our engine simulation tool was then used to explore the effect of various engine design parameters and operating conditions on the HCCI viable operating range. Performance maps, which show the response of the engine during a normal driving cycle, were constructed to compare these engine designs. The simulations showed that an acceptably broad operating range can be achieved by using a low compression ratio, low octane fuel, and moderate boost pressure. An explanation of why this choice of parameters gives a broad operating window is discussed. Our prediction of the HCCI knock limit is based on the autoignition theory of knock, which asserts that local overpressures in the engine are caused by extremely rapid chemical energy release. A competing theory asserts that knock is caused by the formation of detonation waves initiated at autoignition centers ('hot-spots') in the engine. No conclusive experimental evidence exists for the detonation theory, but many numerical simulations in the literature show that detonation formation is possible; however, some of the assumptions made in these simulations warrant re-examination. In particular, the effect of curvature on small (quasispherical) hot-spots has often been overlooked. We first examined the well-studied case of gasoline spark-ignited engine knock and observed that the size of the hot-spot needed to initiate a detonation is larger than the end-gas region where knock occurs. Subsequent studies of HCCI engine knock predicted that detonations would not form regardless of the hot-spot size because of the low energy content of fuel-lean mixtures typically used in these engines. Our predictions of the HCCI viable operating range were shown to be quite sensitive to details of the ignition chemistry. Therefore, an attempt was made to build an improved chemistry model for HCCI combustion using automatic mechanism-generation software developed in our research group. Extensions to the software were made to allow chemistry model construction for engine conditions. Model predictions for n-heptane/air combustion were compared to literature data from a jet-stirred reactor and rapid-compression machine. We conclude that automatic mechanism generation gives fair predictions without the tuning of rate parameters or other efforts to improve agreement. However, some tuning of the automatically-generated chemistry models is necessary to give the accurate predictions of HCCI combustion needed for our design calculations.

Download or read book Inflation Kaufkraft Wechselkurs written by and published by . This book was released on 1986 with total page 16 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Cost Effectiveness and Deployment of Fuel Economy Technologies for Light Duty Vehicles written by National Research Council and published by National Academies Press. This book was released on 2015-09-28 with total page 812 pages. Available in PDF, EPUB and Kindle. Book excerpt: The light-duty vehicle fleet is expected to undergo substantial technological changes over the next several decades. New powertrain designs, alternative fuels, advanced materials and significant changes to the vehicle body are being driven by increasingly stringent fuel economy and greenhouse gas emission standards. By the end of the next decade, cars and light-duty trucks will be more fuel efficient, weigh less, emit less air pollutants, have more safety features, and will be more expensive to purchase relative to current vehicles. Though the gasoline-powered spark ignition engine will continue to be the dominant powertrain configuration even through 2030, such vehicles will be equipped with advanced technologies, materials, electronics and controls, and aerodynamics. And by 2030, the deployment of alternative methods to propel and fuel vehicles and alternative modes of transportation, including autonomous vehicles, will be well underway. What are these new technologies - how will they work, and will some technologies be more effective than others? Written to inform The United States Department of Transportation's National Highway Traffic Safety Administration (NHTSA) and Environmental Protection Agency (EPA) Corporate Average Fuel Economy (CAFE) and greenhouse gas (GHG) emission standards, this new report from the National Research Council is a technical evaluation of costs, benefits, and implementation issues of fuel reduction technologies for next-generation light-duty vehicles. Cost, Effectiveness, and Deployment of Fuel Economy Technologies for Light-Duty Vehicles estimates the cost, potential efficiency improvements, and barriers to commercial deployment of technologies that might be employed from 2020 to 2030. This report describes these promising technologies and makes recommendations for their inclusion on the list of technologies applicable for the 2017-2025 CAFE standards.

Download or read book Design Considerations Modeling and Analysis of Micro homogeneous Charge Compression Ignition Combustion Free piston Engines written by Hans Thomas Aichlmayr and published by . This book was released on 2002 with total page 520 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Evaluation of Technical Feasibility of Homogeneous Charge Compression Ignition HCCI Engine Fueled with Hydrogen Natural Gas and DME written by and published by . This book was released on 2007 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The objective of the proposed project was to confirm the feasibility of using blends of hydrogen and natural gas to improve the performance, efficiency, controllability and emissions of a homogeneous charge compression ignition (HCCI) engine. The project team utilized both engine simulation and laboratory testing to evaluate and optimize how blends of hydrogen and natural gas fuel might improve control of HCCI combustion. GTI utilized a state-of-the art single-cylinder engine test platform for the experimental work in the project. The testing was designed to evaluate the feasibility of extending the limits of HCCI engine performance (i.e., stable combustion, high efficiency and low emissions) on natural gas by using blends of natural gas and hydrogen. Early in the project Ricardo provided technical support to GTI as we applied their engine performance simulation program, WAVE, to our HCCI research engine. Modeling support was later provided by Digital Engines, LLC to use their proprietary model to predict peak pressures and temperatures for varying operating parameters included in the Design of Experiments test plan. Digital Engines also provided testing support for the hydrogen and natural gas blends. Prof. David Foster of University of Wisconsin-Madison participated early in the project by providing technical guidance on HCCI engine test plans and modeling requirements. The main purpose of the testing was to quantify the effects of hydrogen addition to natural gas HCCI. Directly comparing straight natural gas with the hydrogen enhanced test points is difficult due to the complexity of HCCI combustion. With the same air flow rate and lambda, the hydrogen enriched fuel mass flow rate is lower than the straight natural gas mass flow rate. However, the energy flow rate is higher for the hydrogen enriched fuel due to hydrogen's significantly greater lower heating value, 120 mJ/kg for hydrogen compared to 45 mJ/kg for natural gas. With these caveats in mind, an analysis of test results indicates that hydrogen enhanced natural gas HCCI (versus neat natural gas HCCI at comparable stoichiometry) had the following characteristics: (1) Substantially lower intake temperature needed for stable HCCI combustion; (2) Inconclusive impact on engine BMEP and power produced; (3) Small reduction in the thermal efficiency of the engine; (4) Moderate reduction in the unburned hydrocarbons in the exhaust; (5) Slight increase in NOx emissions in the exhaust; (6) Slight reduction in CO2 in the exhaust; and (7) Increased knocking at rich stoichiometry. The major accomplishments and findings from the project can be summarized as follows: (1) A model was calibrated for accurately predicting heat release rate and peak pressures for HCCI combustion when operating on hydrogen and natural gas blends. (2) A single cylinder research engine was thoroughly mapped to compare performance and emissions for micro-pilot natural gas compression ignition, and HCCI combustion for neat natural gas versus blends of natural gas and hydrogen. (3) The benefits of using hydrogen to extend, up to a limit, the stable operating window for HCCI combustion of natural gas at higher intake pressures, leaner air to fuel ratios or lower inlet temperatures was documented.

Download or read book Control and Robustness Analysis of Homogeneous Charge Compression Ignition Using Exhaust Recompression written by Hsien-Hsin Liao and published by Stanford University. This book was released on 2011 with total page 201 pages. Available in PDF, EPUB and Kindle. Book excerpt: There has been an enormous global research effort to alleviate the current and projected environmental consequences incurred by internal combustion (IC) engines, the dominant propulsion systems in ground vehicles. Two technologies have the potential to improve the efficiency and emissions of IC engines in the near future: variable valve actuation (VVA) and homogeneous charge compression ignition (HCCI). IC engines equipped with VVA systems are proven to show better performance by adjusting the valve lift and timing appropriately. An electro-hydraulic valve system (EHVS) is a type of VVA system that possesses full flexibility, i.e., the ability to change the valve lift and timing independently and continuously, making it an ideal rapid prototyping tool in a research environment. Unfortunately, an EHVS typically shows a significant response time delay that limits the achievable closed-loop bandwidth and, as a result, shows poor tracking performance. In this thesis, a control framework that includes system identification, feedback control design, and repetitive control design is presented. The combined control law shows excellent performance with a root-mean-square tracking error below 40 [Mu]m over a maximum valve lift of 4 mm. A stability analysis is also provided to show that the mean tracking error converges to zero asymptotically with the combined control law. HCCI, the other technology presented in this thesis, is a combustion strategy initiated by compressing a homogeneous air-fuel mixture to auto-ignition, therefore, ignition occurs at multiple points inside the cylinder without noticeable flame propagation. The result is rapid combustion with low peak in-cylinder temperature, which gives HCCI improved efficiency and reduces NOx formation. To initiate HCCI with a typical compression ratio, the sensible energy of the mixture needs to be high compared to a spark ignited (SI) strategy. One approach to achieve this, called recompression HCCI, is by closing the exhaust valve early to trap a portion of the exhaust gas in the cylinder. Unlike a SI or Diesel strategy, HCCI lacks an explicit combustion trigger, as autoignition is governed by chemical kinetics. Therefore, the thermo-chemical conditions of the air-fuel mixture need to be carefully controlled for HCCI to occur at the desired timing. Compounding this challenge in recompression HCCI is the re-utilization of the exhaust gas which creates cycle-to-cycle coupling. Furthermore, the coupling characteristics can change drastically around different operating points, making combustion timing control difficult across a wide range of conditions. In this thesis, a graphical analysis examines the in-cylinder temperature dynamics of recompression HCCI and reveals three qualitative types of temperature dynamics. With this insight, a switching linear model is formulated by combining three linear models: one for each of the three types of temperature dynamics. A switching controller that is composed of three local linear feedback controllers can then be designed based on the switching model. This switching model/control formulation is tested on an experimental HCCI testbed and shows good performance in controlling the combustion timing across a wide range. A semi-definite program is formulated to find a Lyapunov function for the switching model/control framework and shows that it is stable. As HCCI is dictated by the in-cylinder thermo-chemical conditions, there are further concerns about the robustness of HCCI, i.e., the boundedness of the thermo-chemical conditions with uncertainty existing in the ambient conditions and in the engine's own characteristics due to aging. To assess HCCI's robustness, this thesis presents a linear parameter varying (LPV) model that captures the dynamics of recompression HCCI and possesses an elegant model structure that is more amenable to analysis. Based on this model, a recursive algorithm using convex optimization is formulated to generate analytical statements about the boundedness of the in-cylinder thermo-chemical conditions. The bounds generated by the algorithm are also shown to relate well to the data from the experimental testbed.

Download or read book Thermal Barrier for Homogeneous Charge Compression Ignition Application written by Edward Lawrence Hurley and published by . This book was released on 2010 with total page 136 pages. Available in PDF, EPUB and Kindle. Book excerpt: Stringent emissions regulations set forth by the Environmental Protection Agency has forced the automotive industry in the United States to seek a low cost and reliable solution to meet these regulations. Homogeneous Charge Compression Ignition (HCCI) is one of the potential answers to the problem. The HCCI combustion process mates the best features of the two main Internal Combustion Engines (ICE) technologies, Spark Ignition (SI) and Compression Ignition Direct Injected (CIDI). The HCCI combustion process is building on the advantages of each technology while avoiding the disadvantages. One of the main hurdles preventing the successful application of an HCCI engine to the main automotive market is the lack of the precise control over the combustion event. Every successful HCCI research engine found during the literature review employed an external energy source to provide the energy boost necessary for the combustion event. The work contained in this thesis was designed to capture the energy normally wasted by the engine through the engine's exhaust and cooling systems with a Thermal Barrier Coating (TBC). The captured energy was used as the energy boost necessary to cause and control HCCI combustion. This was achieved by modifying a Nissan gasoline engine by increasing the compression ratio from 10.3:1 to 13.5:1 along with coating the cylinder head fire deck, valve heads and crown of the pistons with TBC.

Download or read book HCCI and CAI Engines for the Automotive Industry written by Hua Zhao and published by CRC Press. This book was released on 2007-09-10 with total page 562 pages. Available in PDF, EPUB and Kindle. Book excerpt: Homogeneous charge compression ignition (HCCI)/controlled auto-ignition (CAI) has emerged as one of the most promising engine technologies with the potential to combine fuel efficiency and improved emissions performance, offering reduced nitrous oxides and particulate matter alongside efficiency comparable with modern diesel engines. Despite the considerable advantages, its operational range is rather limited and controlling the combustion (timing of ignition and rate of energy release) is still an area of on-going research. Commercial applications are, however, close to reality. HCCI a.

Download or read book Homogeneous Charge Compression Ignition HCCI Engines written by Fuquan Zhao and published by SAE International. This book was released on 2003-01-01 with total page 658 pages. Available in PDF, EPUB and Kindle. Book excerpt: The homogeneous charge, compression-ignition (HCCI) combustion process has the potential to significantly reduce NOx and particulate emissions, while achieving high thermal efficiency and the capability of operating with a wide variety of fuels. This makes the HCCI engine an attractive technology that can ostensibly provide diesel-like fuel efficiency and very low emissions, which may allow emissions compliance to occur without relying on lean aftertreatment systems. A profound increase in the level of research and development of this technology has occurred in the last decade. This book gathers contributions from experts in both industry and academia, providing a basic introduction to the state-of-the-art of HCCI technology, a critical review of current HCCI research and development efforts, and perspective for the future. Chapters cover: Gasoline-Fueled HCCI Engines; Diesel-Fueled HCCI Engines; Alternative Fuels and Fuel Additives for HCCI Engines; HCCI Control and Operating Range Extension; Kinetics of HCCI Combustion; HCCI Engine Modeling Approaches.In addition to the extensive overview of terminology, physical processes, and future needs, each chapter also features select SAE papers (a total of 41 are included in the book), as well as a comprehensive list of references related to the subjects. Homogeneous Charge Compression Ignition (HCCI) Engines: Key Research and Development Issues provides a valuable base of information for those interested in learning about this rapidly-progressing technology which has the potential to enhance fuel economy and reduce emissions.

Download or read book Advances in Internal Combustion Engine Research written by Dhananjay Kumar Srivastava and published by Springer. This book was released on 2017-11-29 with total page 346 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book discusses all aspects of advanced engine technologies, and describes the role of alternative fuels and solution-based modeling studies in meeting the increasingly higher standards of the automotive industry. By promoting research into more efficient and environment-friendly combustion technologies, it helps enable researchers to develop higher-power engines with lower fuel consumption, emissions, and noise levels. Over the course of 12 chapters, it covers research in areas such as homogeneous charge compression ignition (HCCI) combustion and control strategies, the use of alternative fuels and additives in combination with new combustion technology and novel approaches to recover the pumping loss in the spark ignition engine. The book will serve as a valuable resource for academic researchers and professional automotive engineers alike.

Download or read book Modeling the Novel Jones Engine Toroidal Concept in Homogeneous Charge Compression Ignition HCCI and Spark Ignition SI Combustion Model written by and published by . This book was released on 2020 with total page 112 pages. Available in PDF, EPUB and Kindle. Book excerpt: The need for reduced CO2 emissions from transportation and stationary power generation applications has driven engine designers, developers, and researchers to seek new and novel technologies and designs to maximize engine efficiency, reduce weight, and increase engine performance. One such new engine design was proposed by Jones Engine LLC, and called the Jones Engine. The Jones Engine concept utilizes a novel toroidal piston/cylinder configuration, eliminating the connecting rod of the traditional slider-crank mechanism, thereby allowing for a more direct transfer of work from the combustion gases to the crankshaft. Jones Engine LLC promises significantly increase output torque, reduced fuel economy, and decreased engine weight through its unique design. This work seeks to model the Jones Engine's unique engine cycle, and directly compare to analogous conventional reciprocating slider-crank engines to provide an assessment of the benefits and limitations of the Jones Engine concept. In this work, the Jones Engine concept was modeled via a MATLAB based 0-D engine simulation code developed by the authors, utilizing Cantera to solve the gas phase chemical kinetics. The engine was modeled in two combustion modes, Homogeneous Charge Compession Ignition (HCCI), and Spark-Ignited (SI). The HCCI combustion model utilized a homogeneous single-zone incorporating the effects of piston motion, heat transfer, and gas phase kinetics, while the SI combustion model utilized a 2-zone modeling approach with either a prescribed Wiebe function heat release, or a semi-predictive flame propagation model. The engine models were validated against experimental data from conventional engines available in the literature. The results of the simulations showed that at identical engine operating conditions and analogous geometrics, the Jones offered slightly reduced efficiency in HCCI and SI combustion modes, but with significantly higher output torque due to the nature of the Jones Engine mechanism. However, the simulation results indicated several potential benefits of the Jones Engine configuration, including increased knock mitigatation in SI mode, and therefore the ability to operate with significantly higher geometric compression ratios, thereby offering higher efficiency potential.

Download or read book Maximizing Power Output in Homogeneous Charge Compression Ignition HCCI Engines and Enabling Effective Control of Combustion Timing written by Samveg Saxena and published by . This book was released on 2011 with total page 238 pages. Available in PDF, EPUB and Kindle. Book excerpt: Homogeneous Charge Compression Ignition (HCCI) engines are one of the most promising engine technologies for the future of energy conversion from clean, efficient combustion. HCCI engines allow high efficiency and lower CO2 emission through the use of high compression ratios and the removal of intake throttle valves (like Diesel), and allow very low levels of urban pollutants like nitric oxide and soot (like Otto). These engines, however, are not without their challenges, such as low power density compared with other engine technologies, and a difficulty in controlling combustion timing. This dissertation first addresses the power output limits. The particular strategies for enabling high power output investigated in this dissertation focus on avoiding five critical limits that either damage an engine, drastically reduce efficiency, or drastically increase emissions: 1) ringing limits, 2) peak in-cylinder pressure limits, 3) misfire limits, 4) low intake temperature limits, and 5) excessive emissions limits. The research shows that the key factors that enable high power output, sufficient for passenger vehicles, while simultaneously avoiding the five limits defined above are the use of: 1) high intake air pressures allowing improved power output, 2) highly delayed combustion timing to avoid ringing limits, and 3) using the highest possible equivalence ratio before encountering ringing limits. These results are revealed by conducting extensive experiments spanning a wide range of operating conditions on a multi-cylinder HCCI engine. Second, this dissertation discusses strategies for effectively sensing combustion characteristics on a HCCI engine. For effective feedback control of HCCI combustion timing, a sensor is required to quantify when combustion occurs. Many laboratory engines use in-cylinder pressure sensors but these sensors are currently prohibitively expensive for wide-scale commercialization. Instead, ion sensors made from inexpensive sparkplugs are proposed for sensing combustion timing. Ion sensing, however, is unreliable under certain HCCI conditions. The dissertation presents two strategies for improving the usefulness of ion sensors in HCCI engines: 1) the use of tiny fractions of metal-acetate fuel additives that expand the useful range of ion sensors, and 2) the use of ion sensors for detecting excessive ringing that must be avoided in HCCI engines. These two innovative research efforts make ion sensors viable for sensing combustion characteristics across the full range of HCCI operation, making them effective for use in engine control systems. In summary, this Ph. D dissertation addresses two important technical challenges facing HCCI engines: power output limits, and difficulty in sensing combustion characteristics for control applications. The strategies proposed in this dissertation research bring HCCI engines closer to widespread commercialization allowing vehicles to operate with significantly higher efficiency and with cleaner emissions.

Download or read book Design a Four stroke Homogeneous Charge Compression Ignition HCCI Engine written by Mohamad Azzad Mokhri and published by . This book was released on 2011 with total page 62 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Homogeneous Charge Compression Ignition HCCI written by and published by . This book was released on 2004 with total page 332 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Combustion in Homogeneous Charge Compression Ignition Engines written by Daniel Lee Flowers and published by . This book was released on 2001 with total page 382 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Study of homogeneous charge compression ignition HCCI combustion and emission characteristics in a multi cylinder engine written by Jacek Waldemar Misztal and published by . This book was released on 2008 with total page 228 pages. Available in PDF, EPUB and Kindle. Book excerpt: