Download or read book Design of a Non isolated Single Phase Online UPS Topology with Parallel Battery Bank for Low Power Applications written by Muhammad Aamir and published by Springer. This book was released on 2018-07-14 with total page 108 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a new topology of the non-isolated online uninterruptible power supply (UPS) system consisting of 3 components: bridgeless boost rectifier, battery charger/discharger, and an inverter. The online UPS system is considered to be the most preferable UPS due to its high level of power quality and proven reliability against all types of line disturbances and power outages. The new battery charger/discharger reduces the battery bank voltage, which improves performance and reliability, while a new control method for the inverter regulates the output voltage for both linear and nonlinear loads. The proposed USP system shows an efficiency of 94% during battery mode and 92% during the normal mode of operation.
Download or read book Fuel Cell Based Battery less UPS System written by Mirunalini Venkatagiri Chellappan and published by . This book was released on 2008 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: With the increased usage of electrical equipment for various applications, the demand for quality power apart from continuous power availability has increased and hence requires the development of appropriate power conditioning system. A major factor during development of these systems is the requirement that they remain environment-friendly. This cannot be realized using the conventional systems as they use batteries and/or engine generators. Among various viable technologies, fuel cells have emerged as one of the most promising sources for both portable and stationary applications. In this thesis, a new battery less UPS system configuration powered by fuel cell is discussed. The proposed topology utilizes a standard offline UPS module and the battery is replaced by a supercapacitor. The system operation is such that the supercapacitor bank is sized to support startup and load transients and steady state power is supplied by the fuel cell. Further, the fuel cell runs continuously to supply 10% power in steady state. In case of power outage, it is shown that the startup time for fuel cell is reduced and the supercapacitor bank supplies power till the fuel cell ramps up from supplying 10% load to 100% load. A detailed design example is presented for a 200W/350VA 1- phase UPS system to meet the requirements of a critical load. The equivalent circuit and hence the terminal behavior of the fuel cell and the supercapacitor are considered in the analysis and design of the system for a stable operation over a wide range. The steady state and transient state analysis were used for stability verification. Hence, from the tests such as step load changes and response time measurements, the non-linear model of supercapacitor was verified. Temperature rise and fuel consumption data were measured and the advantages of having a hybrid source (supercapacitor in parallel with fuel cell) over just a standalone fuel cell source were shown. Finally, the transfer times for the proposed UPS system and the battery based UPS system were measured and were found to be satisfactory. Overall, the proposed system was found to satisfy the required performance specifications.
Download or read book Handbook on Battery Energy Storage System written by Asian Development Bank and published by Asian Development Bank. This book was released on 2018-12-01 with total page 123 pages. Available in PDF, EPUB and Kindle. Book excerpt: This handbook serves as a guide to deploying battery energy storage technologies, specifically for distributed energy resources and flexibility resources. Battery energy storage technology is the most promising, rapidly developed technology as it provides higher efficiency and ease of control. With energy transition through decarbonization and decentralization, energy storage plays a significant role to enhance grid efficiency by alleviating volatility from demand and supply. Energy storage also contributes to the grid integration of renewable energy and promotion of microgrid.
Download or read book Emerging Power Converters for Renewable Energy and Electric Vehicles written by Md. Rabiul Islam and published by CRC Press. This book was released on 2021-05-30 with total page 419 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers advancements of power electronic converters and their control techniques for grid integration of large-scale renewable energy sources and electrical vehicles. Major emphasis is on transformer-less direct grid integration, bidirectional power transfer, compensation of grid power quality issues, DC system protection and grounding, interaction in mixed AC/DC systems, AC and DC system stability, design of high-frequency high power density systems with advanced soft magnetic materials, modeling and simulation of mixed AC/DC systems, switching strategies for enhanced efficiency, and protection and reliability for sustainable grid integration. This book is an invaluable resource for professionals active in the field of renewable energy and power conversion. Md. Rabiul Islam received his PhD from the University of Technology Sydney (UTS), Australia. He was appointed as a Lecturer at Rajshahi University of Engineering & Technology (RUET) in 2005 and promoted to full-term Professor in 2017. In early 2018, he joined the School of Electrical, Computer, and Telecommunications Engineering, University of Wollongong, Australia. He is a Senior Member of IEEE. His research interests include the fields of power electronic converters, renewable energy technologies, power quality, electrical machines, electric vehicles, and smart grids. He has authored or coauthored more than 200 publications including 50 IEEE Transactions/IEEE Journal papers. He has been serving as an editor for IEEE Transactions on Energy Conversion and IEEE Power Engineering Letters, and associate editor for IEEE Access. Md. Rakibuzzaman Shah is a Senior Lecturer with the School of Engineering, Information Technology and Physical Science at Federation University Australia. He has worked and consulted with distribution network operators and transmission system operators on individual projects and has done collaborative work on a large number of projects (EPSRC project on multi-terminal HVDC, Scottish and Southern Energy multi-infeed HVDC) - primarily on the dynamic impact of integrating new technologies and power electronics into large systems. He is an active member of the IEEE and CIGRE. He has more than 70 international publications and has spoken at the leading power system conferences around the world. His research interests include future power grids (i.e., renewable energy integration, wide-area control), asynchronous grid connection through VSC-HVDC, application of data mining in power system, distribution system energy management, and low carbon energy systems. Mohd. Hasan Ali is currently an Associate Professor with the Electrical and Computer Engineering Department at the University of Memphis, USA, where he leads the Electric Power and Energy Systems (EPES) Laboratory. His research interests include advanced power systems, smart-grid and microgrid systems, renewable energy systems, and cybersecurity issues in modern power grids. Dr. Ali has more than 190 publications, including 2 books, 4 book chapters, 2 patents, 60 top ranked journal papers, 96 peer-reviewed international conference papers, and 20 national conference papers. He serves as the editor of the IEEE Transactions on Sustainable Energy and IET-Generation, Transmission and Distribution (GTD) journal. Dr. Ali is a Senior Member of the IEEE Power and Energy Society (PES). He is also the Chair of the PES of the IEEE Memphis Section.
Download or read book Power Electronics Handbook written by Muhammad H. Rashid and published by Elsevier. This book was released on 2010-07-19 with total page 1189 pages. Available in PDF, EPUB and Kindle. Book excerpt: Power electronics, which is a rapidly growing area in terms of research and applications, uses modern electronics technology to convert electric power from one form to another, such as ac-dc, dc-dc, dc-ac, and ac-ac with a variable output magnitude and frequency. Power electronics has many applications in our every day life such as air-conditioners, electric cars, sub-way trains, motor drives, renewable energy sources and power supplies for computers. This book covers all aspects of switching devices, converter circuit topologies, control techniques, analytical methods and some examples of their applications. * 25% new content* Reorganized and revised into 8 sections comprising 43 chapters* Coverage of numerous applications, including uninterruptable power supplies and automotive electrical systems* New content in power generation and distribution, including solar power, fuel cells, wind turbines, and flexible transmission
Download or read book IGBT Modules written by Andreas Volke and published by . This book was released on 2012 with total page 534 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Introduction to Modern Power Electronics written by Andrzej M. Trzynadlowski and published by John Wiley & Sons. This book was released on 2015-11-16 with total page 468 pages. Available in PDF, EPUB and Kindle. Book excerpt: Provides comprehensive coverage of the basic principles and methods of electric power conversion and the latest developments in the field This book constitutes a comprehensive overview of the modern power electronics. Various semiconductor power switches are described, complementary components and systems are presented, and power electronic converters that process power for a variety of applications are explained in detail. This third edition updates all chapters, including new concepts in modern power electronics. New to this edition is extended coverage of matrix converters, multilevel inverters, and applications of the Z-source in cascaded power converters. The book is accompanied by a website hosting an instructor’s manual, a PowerPoint presentation, and a set of PSpice files for simulation of a variety of power electronic converters. Introduction to Modern Power Electronics, Third Edition: Discusses power conversion types: ac-to-dc, ac-to-ac, dc-to-dc, and dc-to-ac Reviews advanced control methods used in today’s power electronic converters Includes an extensive body of examples, exercises, computer assignments, and simulations Introduction to Modern Power Electronics, Third Edition is written for undergraduate and graduate engineering students interested in modern power electronics and renewable energy systems. The book can also serve as a reference tool for practicing electrical and industrial engineers.
Download or read book Oil and Gas Production Handbook An Introduction to Oil and Gas Production written by Havard Devold and published by Lulu.com. This book was released on 2013 with total page 84 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Sustainable Power Systems written by Nava Raj Karki and published by Springer. This book was released on 2017-01-10 with total page 186 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book deals with quantifying and analyzing the risks associated with sustainable energy technology growth in electric power systems, and developing appropriate models and methodologies to mitigate the risks and improve the overall system performance. The rapid increase in the installation of renewable energy sources in electric power systems has given rise to a wide range of problems related to planning and operation of power systems to maintain quality, stability, reliability and efficiency. Additionally, there is a growing global environmental concern regarding increasing emissions from the electric power generation required to meet rising energy needs and support sustainable and inclusive development. The phenomenon of low voltage ride through (LVRT), common to wind energy systems, is discussed, and ways to tackle the same are proposed in the first chapter. Subsequent chapters propose methods of optimizing a sustainable and smart microgrid, and supplying electricity to remote areas of a developing country with no immediate possibility of national grid extension. The economic benefit and technical challenges of forming localized minigrid are also discussed. The book proposes a method for reliability assessment of a power grid with sustainable power transportation system. The issue of weak link in power system is very important as it will provide the system operators and planners to take necessary measures to strengthen the system. An approach to determine the weak parts of the system and its unreliability is proposed. With increasing installation of HVDC power transmission and development of efficient and low cost power electronic devices, the DC microgrids are becoming a common phenomenon. Their existence together with AC Grids result in Hybrid AC/DC Microgrids, which are discussed in this book. It further presents a method for reliability evaluation of a distribution system with network reconfiguration in the presence of distributed generation. The important problems in sustainable energy growth, and their potential solutions discussed and presented in the book should be of great interest to engineers, policy makers, researchers and academics in the area of electric power engineering.
Download or read book The Art of Electronics written by Paul Horowitz and published by . This book was released on 2021 with total page 1227 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Advanced Concepts for Renewable Energy Supply of Data Centres written by Jaume Salom and published by CRC Press. This book was released on 2022-09-01 with total page 337 pages. Available in PDF, EPUB and Kindle. Book excerpt: The rapid increase of cloud computing, high performance computing (HPC) and the vast growth in Internet and Social Media use have aroused the interest in energy consumption and the carbon footprint of Data Centres. Data Centres primarily contain electronic equipment used for data processing (servers), data storage (storage equipment), and communications (network equipment). Collectively, this equipment processes, stores, and transmits digital information and is known as information technology (IT) equipment. Advanced Concepts for Renewable Energy Supply of Data Centres introduces a number of technical solutions for the supply of power and cooling energy into Data Centres with enhanced utilisation of renewable energy sources in order to achieve low energy Data Centres. Because of the high energy density nature of these unique infrastructures, it is essential to implement energy efficiency measures and reduce consumption before introducing any renewable energy source. A holistic approach is used with the objective of integrating many technical solutions such as management of the IT (Information Technology) load, efficient electrical supply to the IT systems, Low-Ex air-conditioning systems, interaction with district heating and cooling networks, re-use of heat, free cooling (air, seawater, groundwater), optimal use of heat and cold storage, electrical storage and integration in smart grids. This book is therefore a catalogue of advanced technical concepts that could be integrated into Data Centres portfolio in order to increase the overall efficiency and the share of renewable energies in power and cooling supply. Based on dynamic energy models implemented in TRNSYS some concepts are deeply evaluated through yearly simulations. The results of the simulation are illustrated with Sankey charts, where the energy flows per year within the subsystems of each concept for a selected scenario are shown, and graphs showing the results of parametric analysis. A set of environmental metrics (as the non-renewable primary energy) and financial metrics (CAPEX and OPEX) as well of energy efficiency metrics like the well-known PUE, are described and used to evaluate the different technical concepts.
Download or read book Operational Amplifiers and Linear Integrated Circuits written by James M.. Fiore and published by . This book was released on 2002 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The goal of this book is to encourage the reader to become proficient in the analysis and design of circuits utilizing modern linear integrated circuits. It progresses from the fundamental circuit building blocks through to analog and digital conversion systems. A methodical step-by-step presentation introduces the basic idealized operational amplifiers and eventually examines practical limitations in great detail. Each chapter has a problem set and contains extended topic to present extra discussion and details about the subject.
Download or read book IBM z13s Technical Guide written by Octavian Lascu and published by IBM Redbooks. This book was released on 2016-11-10 with total page 588 pages. Available in PDF, EPUB and Kindle. Book excerpt: Digital business has been driving the transformation of underlying information technology (IT) infrastructure to be more efficient, secure, adaptive, and integrated. IT must be able to handle the explosive growth of mobile clients and employees. It also must be able to process enormous amounts of data to provide deep and real-time insights to help achieve the greatest business impact. This IBM® Redbooks® publication addresses the new IBM z SystemsTM single frame, the IBM z13s server. IBM z Systems servers are the trusted enterprise platform for integrating data, transactions, and insight. A data-centric infrastructure must always be available with a 99.999% or better availability, have flawless data integrity, and be secured from misuse. It needs to be an integrated infrastructure that can support new applications. It also needs to have integrated capabilities that can provide new mobile capabilities with real-time analytics delivered by a secure cloud infrastructure. IBM z13s servers are designed with improved scalability, performance, security, resiliency, availability, and virtualization. The superscalar design allows z13s servers to deliver a record level of capacity over the prior single frame z Systems server. In its maximum configuration, the z13s server is powered by up to 20 client characterizable microprocessors (cores) running at 4.3 GHz. This configuration can run more than 18,000 millions of instructions per second (MIPS) and up to 4 TB of client memory. The IBM z13s Model N20 is estimated to provide up to 100% more total system capacity than the IBM zEnterprise® BC12 Model H13. This book provides information about the IBM z13s server and its functions, features, and associated software support. Greater detail is offered in areas relevant to technical planning. It is intended for systems engineers, consultants, planners, and anyone who wants to understand the IBM z SystemsTM functions and plan for their usage. It is not intended as an introduction to mainframes. Readers are expected to be generally familiar with existing IBM z Systems technology and terminology.
Download or read book System z Parallel Sysplex Best Practices written by Frank Kyne and published by IBM Redbooks. This book was released on 2011-01-11 with total page 202 pages. Available in PDF, EPUB and Kindle. Book excerpt: This IBM® Redbooks® publication pulls together diverse information regarding the best way to design, implement, and manage a Parallel Sysplex® to deliver the levels of performance and availability required by your organization. This book should be of interest to system programmers, availability managers, and database administrators who are interested in verifying that your systems conform to IBM best practices for a Parallel Sysplex environment. In addition to z/OS® and the sysplex hardware configuration, this book also covers the major IBM subsystems: CICS® DB2® IMSTM MQ WebSphere® Application Server To get the best value from this book, readers should have hands-on experience with Parallel Sysplex and have working knowledge of how your systems are set up and why they were set up in that manner.
Download or read book Active Power Line Conditioners written by Patricio Salmeron Revuelta and published by Academic Press. This book was released on 2015-07-31 with total page 436 pages. Available in PDF, EPUB and Kindle. Book excerpt: Active Power Line Conditioners: Design, Simulation and Implementation for Improving Power Quality presents a rigorous theoretical and practical approach to active power line conditioners, one of the subjects of most interest in the field of power quality. Its broad approach offers a journey that will allow power engineering professionals, researchers, and graduate students to learn more about the latest landmarks on the different APLC configurations for load active compensation. By introducing the issues and equipment needs that arise when correcting the lack of power quality in power grids, this book helps define power terms according to the IEEE Standard 1459. Detailed chapters discuss instantaneous reactive power theory and the theoretical framework that enabled the practical development of APLCs, in both its original and modified formulations, along with other proposals. Different APLCs configurations for load compensation are explored, including shunt APF, series APF, hybrid APF, and shunt combined with series APF, also known as UPQC. The book includes simulation examples carefully developed and ready for download from the book’s companion website, along with different case studies where real APLCs have been developed. Finally, the new paradigm brought by the emergence of distribution systems with dispersed generation, such as the use of small power units based on gas technology or renewable energy sources, is discussed in a chapter where mitigation technologies are addressed in a distributed environment. Combines the development of theories, control strategies, and the most widespread practical implementations of active power line conditioners, along with the most recent new approaches Details updated and practical content on periodic disturbances mitigation technologies with special emphasis on distributed generation systems Includes over 28 practical simulation examples in Matlab-Simulink which are available for download at the book’s companion website, with 4 reproducible case studies from real APLCs
Download or read book Lifelines written by Stephane Hallegatte and published by World Bank Publications. This book was released on 2019-07-16 with total page 220 pages. Available in PDF, EPUB and Kindle. Book excerpt: Infrastructure—electricity, telecommunications, roads, water, and sanitation—are central to people’s lives. Without it, they cannot make a living, stay healthy, and maintain a good quality of life. Access to basic infrastructure is also a key driver of economic development. This report lays out a framework for understanding infrastructure resilience - the ability of infrastructure systems to function and meet users’ needs during and after a natural hazard. It focuses on four infrastructure systems that are essential to economic activity and people’s well-being: power systems, including the generation, transmission, and distribution of electricity; water and sanitation—especially water utilities; transport systems—multiple modes such as road, rail, waterway, and airports, and multiple scales, including urban transit and rural access; and telecommunications, including telephone and Internet connections.
Download or read book Planning Guide for Power Distribution Plants written by Hartmut Kiank and published by John Wiley & Sons. This book was released on 2012-01-27 with total page 427 pages. Available in PDF, EPUB and Kindle. Book excerpt: When planning an industrial power supply plant, the specific requirements of the individual production process are decisive for the design and mode of operation of the network and for the selection and design and ratings of the operational equipment. Since the actual technical risks are often hidden in the profound and complex planning task, planning decisions should be taken after responsible and careful consideration because of their deep effects on supply quality and energy efficiency. This book is intended for engineers and technicians of the energy industry, industrial companies and planning departments. It provides basic technical network and plant knowledge on planning, installation and operation of reliable and economic industrial networks. In addition, it facilitates training for students and graduates in this field. In an easy and comprehensible way, this book informs about solution competency gained in many years of experience. Moreover, it also offers planning recommendations and knowledge on standards and specifications, the use of which ensures that technical risks are avoided and that production and industrial processes can be carried out efficiently, reliably and with the highest quality.
