Download or read book Design and Implementation of an AC to DC Matrix Converter with High Frequency Isolation and Power Factor Correction for Particle Accelerator Applications written by Rafael Garcia Gil and published by Universal-Publishers. This book was released on 2005-11-05 with total page 282 pages. Available in PDF, EPUB and Kindle. Book excerpt: This thesis (written in Spanish) presents the analysis, design and implementation of a four-quadrant power supply with high-frequency isolation, which is expected to be used to feed the low-energy correction magnet of a particle accelerator. In particle accelerator applications the magnetic field during beam acceleration may be either positive or negative, and true bipolar power converters are needed. The selected bipolar topology consists of a bidirectional three-phase to single-phase reduced matrix converter (RMC) with power factor correction and a bidirectional active rectifier. Main features of this power converter are the ability to regenerate energy back to the utility when the magnet acts as generator, unity power factor at the mains and reduction of volume and weight thanks to the inclusion of the isolation transformer at the switching frequency. A space vector modulation (SVM) technique was used to achieve unity power factor at the input and output current regulation simultaneously. This was done while a symmetrical pure AC profile is generated at the primary side of the isolation transformer. The secondary AC signal is then rectified into a positive or negative voltage, according to the desired output current sign, and later filtered to obtain the output DC current in both polarities. The active rectifier used permits reverse current flow to the primary side when driving an inductive load. By synchronising the commutation of both converters and adding a saturable inductor and a blocking capacitor it is possible to achieve soft commutation for most of the semiconductor elements. An all-digital control based on a Digital-Signal-Processor (DSP) and a Field-Programmed-Gate-Array (FPGA) was used to implement space vector modulation and output current regulation. Output current regulation is performed on a powerful 32-bit fixed-point DSP of Motorola, and was implemented by means of an observer based optimum state feedback control (LQR -- Linear Quadratic Regulator). A reduced order observer was implemented to estimate the output filter inductor current, reducing the number of sensors. Experimental results of a 1.5 kW, 20 kHz prototype are presented to illustrate the performance of the proposed topology.

Download or read book Electrical Electronics Abstracts written by and published by . This book was released on 1994 with total page 976 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Feedback Systems written by Karl Johan Åström and published by Princeton University Press. This book was released on 2021-02-02 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The essential introduction to the principles and applications of feedback systems—now fully revised and expanded This textbook covers the mathematics needed to model, analyze, and design feedback systems. Now more user-friendly than ever, this revised and expanded edition of Feedback Systems is a one-volume resource for students and researchers in mathematics and engineering. It has applications across a range of disciplines that utilize feedback in physical, biological, information, and economic systems. Karl Åström and Richard Murray use techniques from physics, computer science, and operations research to introduce control-oriented modeling. They begin with state space tools for analysis and design, including stability of solutions, Lyapunov functions, reachability, state feedback observability, and estimators. The matrix exponential plays a central role in the analysis of linear control systems, allowing a concise development of many of the key concepts for this class of models. Åström and Murray then develop and explain tools in the frequency domain, including transfer functions, Nyquist analysis, PID control, frequency domain design, and robustness. Features a new chapter on design principles and tools, illustrating the types of problems that can be solved using feedback Includes a new chapter on fundamental limits and new material on the Routh-Hurwitz criterion and root locus plots Provides exercises at the end of every chapter Comes with an electronic solutions manual An ideal textbook for undergraduate and graduate students Indispensable for researchers seeking a self-contained resource on control theory

Download or read book Applications of Power Electronics written by Frede Blaabjerg and published by MDPI. This book was released on 2019-06-24 with total page 476 pages. Available in PDF, EPUB and Kindle. Book excerpt: Power electronics technology is still an emerging technology, and it has found its way into many applications, from renewable energy generation (i.e., wind power and solar power) to electrical vehicles (EVs), biomedical devices, and small appliances, such as laptop chargers. In the near future, electrical energy will be provided and handled by power electronics and consumed through power electronics; this not only will intensify the role of power electronics technology in power conversion processes, but also implies that power systems are undergoing a paradigm shift, from centralized distribution to distributed generation. Today, more than 1000 GW of renewable energy generation sources (photovoltaic (PV) and wind) have been installed, all of which are handled by power electronics technology. The main aim of this book is to highlight and address recent breakthroughs in the range of emerging applications in power electronics and in harmonic and electromagnetic interference (EMI) issues at device and system levels as discussed in ‎robust and reliable power electronics technologies, including fault prognosis and diagnosis technique stability of grid-connected converters and ‎smart control of power electronics in devices, microgrids, and at system levels.

Download or read book High Voltage Engineering Fundamentals written by John Kuffel and published by Elsevier. This book was released on 2000-07-17 with total page 556 pages. Available in PDF, EPUB and Kindle. Book excerpt: Power transfer for large systems depends on high system voltages. The basics of high voltage laboratory techniques and phenomena, together with the principles governing the design of high voltage insulation, are covered in this book for students, utility engineers, designers and operators of high voltage equipment. In this new edition the text has been entirely revised to reflect current practice. Major changes include coverage of the latest instrumentation, the use of electronegative gases such as sulfur hexafluoride, modern diagnostic techniques, and high voltage testing procedures with statistical approaches. - A classic text on high voltage engineering - Entirely revised to bring you up-to-date with current practice - Benefit from expanded sections on testing and diagnostic techniques

Download or read book Passive Nondestructive Assay of Nuclear Materials written by Doug Reilly and published by . This book was released on 1991 with total page 700 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Neutron Generators for Analytical Purposes written by International Atomic Energy Agency and published by IAEA Radiation Technology Repo. This book was released on 2012 with total page 145 pages. Available in PDF, EPUB and Kindle. Book excerpt: This publication addresses recent developments in neutron generator (NG) technology. It presents information on compact instruments with high neutron yield to be used for neutron activation analysis (NAA) and prompt gamma neutron activation analysis in combination with high count rate spectrometers. Traditional NGs have been shown to be effective for applications including borehole logging, homeland security, nuclear medicine and the on-line analysis of aluminium, coal and cement. Pulsed fast thermal neutron analysis, as well as tagged and timed neutron analysis, are additional techniques which can be applied using NG. Furthermore, NG can effectively be used for elemental analysis and is also effective for analysis of hidden materials by neutron radiography. Useful guidelines for developing NG based research laboratories are also provided in this publication.

Download or read book Semiconductor Detector Systems written by Helmuth Spieler and published by OUP Oxford. This book was released on 2005-08-25 with total page 513 pages. Available in PDF, EPUB and Kindle. Book excerpt: Semiconductor sensors patterned at the micron scale combined with custom-designed integrated circuits have revolutionized semiconductor radiation detector systems. Designs covering many square meters with millions of signal channels are now commonplace in high-energy physics and the technology is finding its way into many other fields, ranging from astrophysics to experiments at synchrotron light sources and medical imaging. This book is the first to present a comprehensive discussion of the many facets of highly integrated semiconductor detector systems, covering sensors, signal processing, transistors and circuits, low-noise electronics, and radiation effects. The diversity of design approaches is illustrated in a chapter describing systems in high-energy physics, astronomy, and astrophysics. Finally a chapter "Why things don't work" discusses common pitfalls. Profusely illustrated, this book provides a unique reference in a key area of modern science.

Download or read book Science Citation Index written by and published by . This book was released on 1993 with total page 2300 pages. Available in PDF, EPUB and Kindle. Book excerpt: Vols. for 1964- have guides and journal lists.

Download or read book Iron Dominated Electromagnets Design Fabrication Assembly And Measurements written by Jack T Tanabe and published by World Scientific Publishing Company. This book was released on 2005-05-06 with total page 355 pages. Available in PDF, EPUB and Kindle. Book excerpt: This unique book, written by one of the world's foremost specialists in the field, is devoted to the design of low and medium field electromagnets whose field level and quality (uniformity) are dominated by the pole shape and saturation characteristics of the iron yoke.The wide scope covers material ranging from the physical requirements for typical high performance accelerators, through the mathematical relationships which describe the shape of two-dimensional magnetic fields, to the mechanical fabrication, assembly, installation, and alignment of magnets in a typical accelerator lattice. In addition, stored energy concepts are used to develop magnetic force relationships and expressions for magnets with time varying fields.The material in the book is derived from lecture notes used in a course at the Lawrence Livermore National Laboratory and subsequently expanded for the U.S. Particle Accelerator School, making this text an invaluable reference for students planning to enter the field of high energy physics.Mathematical relationships tying together magnet design and measurement theory are derived from first principles, and chapters are included that describe mechanical design, fabrication, installation, and alignment. Some fabrication and assembly practices are reviewed to ensure personnel and equipment safety and operational reliability of electromagnets and their power supply systems. This additional coverage makes the book an important resource for those already in the particle accelerator business as well as those requiring the design and fabrication of low and medium field level magnets for charged particle beam transport in ion implantation and medical applications.

Download or read book Frequency Standards written by Fritz Riehle and published by John Wiley & Sons. This book was released on 2006-03-06 with total page 540 pages. Available in PDF, EPUB and Kindle. Book excerpt: Of all measurement units, frequency is the one that may be determined with the highest degree of accuracy. It equally allows precise measurements of other physical and technical quantities, whenever they can be measured in terms of frequency. This volume covers the central methods and techniques relevant for frequency standards developed in physics, electronics, quantum electronics, and statistics. After a review of the basic principles, the book looks at the realisation of commonly used components. It then continues with the description and characterisation of important frequency standards from atomic clocks, to frequency stabilised lasers. The whole is rounded of with a discussion of topical applications in engineering, telecommunications, and metrology.

Download or read book Power Electronic Converters written by Robert Bausiere and published by Springer Science & Business Media. This book was released on 2013-06-29 with total page 422 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is the third in a series of four devoted to POWER ELECTRONIC CONVERTERS: The first of these concerns AC to DC conversion. The second concerns AC to AC conversion. This volume examines DC to DC conversion. The fourth is devoted to DC to AC conversion. Converters which carry out the DC-DC conversion operate by chopping the input voltage or current: they are called choppers or switch-mode power converters. Their operating frequency is not imposed by either the input or the output, both of which are at zero frequency. A frequency which is much greater than that of the industrial network can be chosen, provided that suitable configurations and semiconductor devices are used. This is the first difference compared to the rectifiers and AC-AC converters, analyzed in the previous volumes and which often operate at the industrial network frequency. The second difference concerns the commutation mode. Choppers operate in forced commutation. The beginning of an operating phase does not auto matically turn off the semiconductor devices which were conducting during the previous phase and which have to be brought to the blocking state. This turn-off must be carried out autonomously. These two differences - the higher frequency of commutations and, espe cially, the different mode of commutation -justify the first two chapters in this work: - Chapter 1 examines general notions concerning converters, supplies and loads, and more especially, how they can be characterized with regard to commutations.

Download or read book Modular Multilevel Converters written by Sixing Du and published by John Wiley & Sons. This book was released on 2018-02-22 with total page 386 pages. Available in PDF, EPUB and Kindle. Book excerpt: An invaluable academic reference for the area of high-power converters, covering all the latest developments in the field High-power multilevel converters are well known in industry and academia as one of the preferred choices for efficient power conversion. Over the past decade, several power converters have been developed and commercialized in the form of standard and customized products that power a wide range of industrial applications. Currently, the modular multilevel converter is a fast-growing technology and has received wide acceptance from both industry and academia. Providing adequate technical background for graduate- and undergraduate-level teaching, this book includes a comprehensive analysis of the conventional and advanced modular multilevel converters employed in motor drives, HVDC systems, and power quality improvement. Modular Multilevel Converters: Analysis, Control, and Applications provides an overview of high-power converters, reference frame theory, classical control methods, pulse width modulation schemes, advanced model predictive control methods, modeling of ac drives, advanced drive control schemes, modeling and control of HVDC systems, active and reactive power control, power quality problems, reactive power, harmonics and unbalance compensation, modeling and control of static synchronous compensators (STATCOM) and unified power quality compensators. Furthermore, this book: Explores technical challenges, modeling, and control of various modular multilevel converters in a wide range of applications such as transformer and transformerless motor drives, high voltage direct current transmission systems, and power quality improvement Reflects the latest developments in high-power converters in medium-voltage motor drive systems Offers design guidance with tables, charts graphs, and MATLAB simulations Modular Multilevel Converters: Analysis, Control, and Applications is a valuable reference book for academic researchers, practicing engineers, and other professionals in the field of high power converters. It also serves well as a textbook for graduate-level students.

Download or read book High Frequency Magnetic Components written by Marian K. Kazimierczuk and published by John Wiley & Sons. This book was released on 2011-08-24 with total page 510 pages. Available in PDF, EPUB and Kindle. Book excerpt: If you are looking for a complete study of the fundamental concepts in magnetic theory, read this book. No other textbook covers magnetic components of inductors and transformers for high-frequency applications in detail. This unique text examines design techniques of the major types of inductors and transformers used for a wide variety of high-frequency applications including switching-mode power supplies (SMPS) and resonant circuits. It describes skin effect and proximity effect in detail to provide you with a sound understanding of high-frequency phenomena. As well as this, you will discover thorough coverage on: integrated inductors and the self-capacitance of inductors and transformers, with expressions for self-capacitances in magnetic components; criteria for selecting the core material, as well as core shape and size, and an evaluation of soft ferromagnetic materials used for magnetic cores; winding resistance at high frequencies; expressions for winding and core power losses when non-sinusoidal inductor or transformer current waveforms contain harmonics. Case studies, practical design examples and procedures (using the area product method and the geometry coefficient method) are expertly combined with concept-orientated explanations and student-friendly analysis. Supplied at the end of each chapter are summaries of the key concepts, review questions, and problems, the answers to which are available in a separate solutions manual. Such features make this a fantastic textbook for graduates, senior level undergraduates and professors in the area of power electronics in addition to electrical and computer engineering. This is also an inimitable reference guide for design engineers of power electronics circuits, high-frequency transformers and inductors in areas such as (SMPS) and RF power amplifiers and circuits.

Download or read book Power Electronic Converter Harmonics written by D. A. Paice and published by Institute of Electrical & Electronics Engineers(IEEE). This book was released on 1996 with total page 234 pages. Available in PDF, EPUB and Kindle. Book excerpt: Electrical Engineering/Power and Energy Engineering Power Electronic Converter Harmonics Multipulse Methods for Clean Power "An excellent treatment of the subject." --Allan Ludbrook, Ludbrook & Associates "Pulls all the material together and presents it from the viewpoint of a long-time practitioner in the field . will be much appreciated by designers, the utilities, and users." --Thomas Barton, University of Calgary Stay on the cutting edge of applied power electronics for energy-saving systems with this invaluable guide to multipulse converters, power sources, and the IEEE Industry Standard 519. One of the foremost experts in the field and holder of 28 patents, Derek A. Paice brings you new circuit schematics and easy-to-follow methods for practical system analysis, using actual field test results. This book offers thorough coverage of: * Requirements, calculations, and standards for harmonics * Power source representation * Multipulse methods and transformers * Double-wound, auto-wound, interphase, and current-control transformers * Multiphase circuit performance * Practical applications * Useful formulas for analysis Power Electronic Converter Harmonics will be indispensable to anyone looking for optimum concepts for power electronics design, including applications engineers, consultants, and manufacturers. Also of Interest from IEEE Press. Printed Circuit Board Design Techniques for EMC Compliance Mark I. Montrose 1996 Hardcover 256 pp IEEE Order No. PC5595 ISBN 0-7803-1131-0 electromagnetic Compatibility in Power Electronics Laszlo Tihanyi 1995 Hardcover 416 pp IEEE Order No. PC3129 ISBN 0-7803-0416-0 Handbook of Electrical and Electronic Insulating Materials Second Edition W. Tillar Shugg, Shugg Enterprises, Inc. 1995 Hardcover 608 pp IEEE Order No. PC 3780 ISBN 0-7803-1030-6.

Download or read book Vehicle Propulsion Systems written by Lino Guzzella and published by Springer Science & Business Media. This book was released on 2007-09-21 with total page 345 pages. Available in PDF, EPUB and Kindle. Book excerpt: The authors of this text have written a comprehensive introduction to the modeling and optimization problems encountered when designing new propulsion systems for passenger cars. It is intended for persons interested in the analysis and optimization of vehicle propulsion systems. Its focus is on the control-oriented mathematical description of the physical processes and on the model-based optimization of the system structure and of the supervisory control algorithms.

Download or read book Foundations of Analog and Digital Electronic Circuits written by Anant Agarwal and published by Elsevier. This book was released on 2005-07-01 with total page 1009 pages. Available in PDF, EPUB and Kindle. Book excerpt: Unlike books currently on the market, this book attempts to satisfy two goals: combine circuits and electronics into a single, unified treatment, and establish a strong connection with the contemporary world of digital systems. It will introduce a new way of looking not only at the treatment of circuits, but also at the treatment of introductory coursework in engineering in general. Using the concept of ''abstraction,'' the book attempts to form a bridge between the world of physics and the world of large computer systems. In particular, it attempts to unify electrical engineering and computer science as the art of creating and exploiting successive abstractions to manage the complexity of building useful electrical systems. Computer systems are simply one type of electrical systems.+Balances circuits theory with practical digital electronics applications.+Illustrates concepts with real devices.+Supports the popular circuits and electronics course on the MIT OpenCourse Ware from which professionals worldwide study this new approach.+Written by two educators well known for their innovative teaching and research and their collaboration with industry.+Focuses on contemporary MOS technology.