Download or read book Design and Control of Power Converters 2020 written by Manuel Arias and published by MDPI. This book was released on 2021-06-04 with total page 188 pages. Available in PDF, EPUB and Kindle. Book excerpt: In this book, nine papers focusing on different fields of power electronics are gathered, all of which are in line with the present trends in research and industry. Given the generality of the Special Issue, the covered topics range from electrothermal models and losses models in semiconductors and magnetics to converters used in high-power applications. In this last case, the papers address specific problems such as the distortion due to zero-current detection or fault investigation using the fast Fourier transform, all being focused on analyzing the topologies of high-power high-density applications, such as the dual active bridge or the H-bridge multilevel inverter. All the papers provide enough insight in the analyzed issues to be used as the starting point of any research. Experimental or simulation results are presented to validate and help with the understanding of the proposed ideas. To summarize, this book will help the reader to solve specific problems in industrial equipment or to increase their knowledge in specific fields.

Download or read book Design and Control of Power Converters 2019 written by Manuel Arias and published by MDPI. This book was released on 2021-07-02 with total page 402 pages. Available in PDF, EPUB and Kindle. Book excerpt: In this book, 20 papers focused on different fields of power electronics are gathered. Approximately half of the papers are focused on different control issues and techniques, ranging from the computer-aided design of digital compensators to more specific approaches such as fuzzy or sliding control techniques. The rest of the papers are focused on the design of novel topologies. The fields in which these controls and topologies are applied are varied: MMCs, photovoltaic systems, supercapacitors and traction systems, LEDs, wireless power transfer, etc.

Download or read book Control of Power Electronic Converters and Systems Volume 4 written by Frede Blaabjerg and published by Academic Press. This book was released on 2024-02-24 with total page 642 pages. Available in PDF, EPUB and Kindle. Book excerpt: Control of Power Electronic Converters and Systems, Volume Four covers emerging topics in the control of power electronics and converters not covered in previous volumes, including emerging power converter topologies, storage systems, battery chargers and the smart transformer. This updated edition specifically focuses on emerging power converter topologies and discusses very recent advances and topics with applications in power electronics and formidable probable dynamics. Chapters include modeling of power converters and their control, with supportive simulations and additional experimental results.Anyone looking for fundamental knowledge regarding new trends in power electronics by application, and also ready to use models and methodologies in their design, control and testing will find this the next invaluable resource in this highly regarded series. - Combines essential control design methods and trends with different applications of power convertor topologies - Includes global perspectives, case studies and real examples from different applications and their control - Features ready-to-use models and methodologies in power electronic application, their design, control and testing

Download or read book Design Control and Application of Modular Multilevel Converters for HVDC Transmission Systems written by Kamran Sharifabadi and published by John Wiley & Sons. This book was released on 2016-10-17 with total page 414 pages. Available in PDF, EPUB and Kindle. Book excerpt: Design, Control and Application of Modular Multilevel Converters for HVDC Transmission Systems is a comprehensive guide to semiconductor technologies applicable for MMC design, component sizing control, modulation, and application of the MMC technology for HVDC transmission. Separated into three distinct parts, the first offers an overview of MMC technology, including information on converter component sizing, Control and Communication, Protection and Fault Management, and Generic Modelling and Simulation. The second covers the applications of MMC in offshore WPP, including planning, technical and economic requirements and optimization options, fault management, dynamic and transient stability. Finally, the third chapter explores the applications of MMC in HVDC transmission and Multi Terminal configurations, including Supergrids. Key features: Unique coverage of the offshore application and optimization of MMC-HVDC schemes for the export of offshore wind energy to the mainland. Comprehensive explanation of MMC application in HVDC and MTDC transmission technology. Detailed description of MMC components, control and modulation, different modeling approaches, converter dynamics under steady-state and fault contingencies including application and housing of MMC in HVDC schemes for onshore and offshore. Analysis of DC fault detection and protection technologies, system studies required for the integration of HVDC terminals to offshore wind power plants, and commissioning procedures for onshore and offshore HVDC terminals. A set of self-explanatory simulation models for HVDC test cases is available to download from the companion website. This book provides essential reading for graduate students and researchers, as well as field engineers and professionals who require an in-depth understanding of MMC technology.

Download or read book Analysis Optimization and Control of Grid Interfaced Matrix Based Isolated AC DC Converters written by Jaydeep Saha and published by Springer Nature. This book was released on 2022-11-05 with total page 295 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents novel contributions in the development of solid-state-transformer (SST) technology both for medium-voltage (MV) and low-voltage (LV) utility grid interfaces, which can potentially augment the grid modernization process in the evolving power system paradigm. For the MV interface, a single-stage AC-DC SST submodule topology has been proposed, and its modulation and soft-switching possibilities are analysed, experimentally validated and adequately benchmarked. A control scheme with power balance capability among submodules is developed for MV grid-connected single-stage AC-DC SST for smooth operation under inevitable parameter drift scenario, and experimental validation shows excellent performance under drastic load change conditions. A novel machine learning-aided multi-objective design optimization framework for grid-connected SST is developed and experimentally validated, which equips a power electronics design engineer with meagre computational resources to find out the most optimal SST design in a convenient time-frame. This book has also contributed towards the development of dual-active-bridge (DAB)-type and non-DAB-type LV grid-interfaced isolated AC-DC converters by providing solutions to specific topology and modulation-related shortcomings in these two types of topologies. A comprehensive comparison of the DAB and non-DAB-type LVAC-LVDC converters reveals the superiority of DAB-type conversion strategy.

Download or read book The proceedings of the 16th Annual Conference of China Electrotechnical Society written by Qingxin Yang and published by Springer Nature. This book was released on 2022-04-17 with total page 1465 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book gathers outstanding papers presented at the 16th Annual Conference of China Electrotechnical Society, organized by China Electrotechnical Society (CES), held in Beijing, China, from September 24 to 26, 2021. It covers topics such as electrical technology, power systems, electromagnetic emission technology, and electrical equipment. It introduces the innovative solutions that combine ideas from multiple disciplines. The book is very much helpful and useful for the researchers, engineers, practitioners, research students, and interested readers.

Download or read book Design of Three phase AC Power Electronics Converters written by Fei "Fred" Wang and published by John Wiley & Sons. This book was released on 2023-11-08 with total page 692 pages. Available in PDF, EPUB and Kindle. Book excerpt: DESIGN OF THREE-PHASE AC POWER ELECTRONICS CONVERTERS Comprehensive resource on design of power electronics converters for three-phase AC applications Design of Three-phase AC Power Electronics Converters contains a systematic discussion of the three-phase AC converter design considering various electrical, thermal, and mechanical subsystems and functions. Focusing on establishing converter components and subsystems models needed for the design, the text demonstrates example designs for these subsystems and for the whole three-phase AC converters considering interactions among subsystems. The design methods apply to different applications and topologies. The text presents the basics of the three-phase AC converter, its design, and the goal and organization of the book, focusing on the characteristics and models important to the converter design for components commonly used in three-phase AC converters. The authors present the design of subsystems, including passive rectifiers, inverters and active rectifiers, electromagnetic interference (EMI) filters, thermal management system, control and auxiliaries, mechanical system, and application considerations, and discuss design optimization, which presents methodology to achieve optimal design results for three-phase AC converters. Specific sample topics covered in Design of Three-phase AC Power Electronics Converters include: Models and characteristics for devices most commonly used in three-phase converters, including conventional Si devices, and emerging SiC and GaN devices Models and selection of various capacitors; characteristics and design of magnetics using different types of magnetic cores, with a focus on inductors Optimal three-phase AC converter design including design and selection of devices, AC line inductors, DC bus capacitors, EMI filters, heatsinks, and control. The design considers both steady-state and transient conditions Load and source impact converter design, such as motors and grid condition impacts For researchers and graduate students in power electronics, along with practicing engineers working in the area of three-phase AC converters, Design of Three-phase AC Power Electronics Converters serves as an essential resource for the subject and may be used as a textbook or industry reference.

Download or read book Energy Efficiency in Electric Motors Drives Power Converters and Related Systems written by Mario Marchesoni and published by MDPI. This book was released on 2020-06-25 with total page 248 pages. Available in PDF, EPUB and Kindle. Book excerpt: Today, there is a great deal of attention focused on sustainable growth worldwide. The increase in efficiency in the use of energy may even, in this historical moment, bring greater benefit than the use of renewable energies. Electricity appears to be the most sustainable of energies and the most promising hope for a planet capable of growing without compromising its own health and that of its inhabitants. Power electronics and electrical drives are the key technologies that will allow energy savings through the reduction of energy losses in many applications. This Special Issue has collected several scientific contributions related to energy efficiency in electrical equipment. Some articles are dedicated to the use and optimization of permanent magnet motors, which allow obtaining the highest level of efficiency. Most of the contributions describe the energy improvements that can be achieved with power electronics and the use of suitable control techniques. Last but not least, some articles describe interesting solutions for hybrid vehicles, which were created mainly to save energy in the smartest way possible.

Download or read book Emerging Power Converters for Renewable Energy and Electric Vehicles written by Md. Rabiul Islam and published by CRC Press. This book was released on 2021-05-30 with total page 419 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers advancements of power electronic converters and their control techniques for grid integration of large-scale renewable energy sources and electrical vehicles. Major emphasis is on transformer-less direct grid integration, bidirectional power transfer, compensation of grid power quality issues, DC system protection and grounding, interaction in mixed AC/DC systems, AC and DC system stability, design of high-frequency high power density systems with advanced soft magnetic materials, modeling and simulation of mixed AC/DC systems, switching strategies for enhanced efficiency, and protection and reliability for sustainable grid integration. This book is an invaluable resource for professionals active in the field of renewable energy and power conversion. Md. Rabiul Islam received his PhD from the University of Technology Sydney (UTS), Australia. He was appointed as a Lecturer at Rajshahi University of Engineering & Technology (RUET) in 2005 and promoted to full-term Professor in 2017. In early 2018, he joined the School of Electrical, Computer, and Telecommunications Engineering, University of Wollongong, Australia. He is a Senior Member of IEEE. His research interests include the fields of power electronic converters, renewable energy technologies, power quality, electrical machines, electric vehicles, and smart grids. He has authored or coauthored more than 200 publications including 50 IEEE Transactions/IEEE Journal papers. He has been serving as an editor for IEEE Transactions on Energy Conversion and IEEE Power Engineering Letters, and associate editor for IEEE Access. Md. Rakibuzzaman Shah is a Senior Lecturer with the School of Engineering, Information Technology and Physical Science at Federation University Australia. He has worked and consulted with distribution network operators and transmission system operators on individual projects and has done collaborative work on a large number of projects (EPSRC project on multi-terminal HVDC, Scottish and Southern Energy multi-infeed HVDC) - primarily on the dynamic impact of integrating new technologies and power electronics into large systems. He is an active member of the IEEE and CIGRE. He has more than 70 international publications and has spoken at the leading power system conferences around the world. His research interests include future power grids (i.e., renewable energy integration, wide-area control), asynchronous grid connection through VSC-HVDC, application of data mining in power system, distribution system energy management, and low carbon energy systems. Mohd. Hasan Ali is currently an Associate Professor with the Electrical and Computer Engineering Department at the University of Memphis, USA, where he leads the Electric Power and Energy Systems (EPES) Laboratory. His research interests include advanced power systems, smart-grid and microgrid systems, renewable energy systems, and cybersecurity issues in modern power grids. Dr. Ali has more than 190 publications, including 2 books, 4 book chapters, 2 patents, 60 top ranked journal papers, 96 peer-reviewed international conference papers, and 20 national conference papers. He serves as the editor of the IEEE Transactions on Sustainable Energy and IET-Generation, Transmission and Distribution (GTD) journal. Dr. Ali is a Senior Member of the IEEE Power and Energy Society (PES). He is also the Chair of the PES of the IEEE Memphis Section.

Download or read book Analysis and Simulation of Electrical and Computer Systems written by Damian Mazur and published by Springer. This book was released on 2017-10-20 with total page 444 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book addresses selected topics in electrical engineering, electronics and mechatronics that have posed serious challenges for both the scientific and engineering communities in recent years. The topics covered range from mathematical models of electrical and electronic components and systems, to simulation tools implemented for their analysis and further developments; and from multidisciplinary optimization, signal processing methods and numerical results, to control and diagnostic techniques. By bridging theory and practice in the modeling, design and optimization of electrical, electromechanical and electronic systems, and by adopting a multidisciplinary perspective, the book provides researchers and practitioners with timely and extensive information on the state of the art in the field — and a source of new, exciting ideas for further developments and collaborations. The book presents selected results of the XIII Scientific Conference on Selected Issues of Electrical Engineering and Electronics (WZEE 2016), held on May 04–08, 2016, in Rzeszów, Poland. The Conference was organized by the Rzeszów Division of Polish Association of Theoretical and Applied Electrical Engineering (PTETiS) in cooperation with the Faculty of Electrical and Computer Engineering of the Rzeszów University of Technology.

Download or read book DC DC Converters for Future Renewable Energy Systems written by Neeraj Priyadarshi and published by Springer Nature. This book was released on 2021-09-27 with total page 480 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book presents the analysis and control of numerous DC-DC converters widely used in several applications such as standalone, grid integration, and motor drives-based renewable energy systems. The book provides extensive simulation and practical analysis of recent and advanced DC-DC power converter topologies. This self-contained book contributes to DC-DC converters design, control techniques, and industrial as well as domestic applications of renewable energy systems. This volume will be useful for undergraduate/postgraduate students, energy planners, designers, system analysis, and system governors.

Download or read book Silicon Carbide Ceramics written by Andrew J. Ruys and published by Elsevier. This book was released on 2023-01-22 with total page 588 pages. Available in PDF, EPUB and Kindle. Book excerpt: It has been three decades since the last significant book was published on SiC ceramics (other than those books that specifically focus on SiC semiconductors). Thirty years has been a long time in the world of SiC ceramics. In the early 1990s, SiC was still a relatively obscure ceramic even within the materials community, prominent only as an industrial abrasive (carborundum), and a refractory (Chapter 7). This has all changed dramatically in the 21st century. For example, - As a semiconductor, SiC greatly surpasses silicon in performance, especially in high-power systems. Its market penetration since its launch in 2001 has been exponential. Single-crystal SiC semiconductors are covered in Chapter 3 - Millions of military and paramilitary personnel have globally been protected with lightweight SiC body armour, since the late 1990s. Body armour is covered in Chapters 4 and 5 - SiC–SiC is a composite material close to commercialization that makes possible high-temperature load-bearing applications hitherto only able to be hypothesized: from ultra-high-temperature jet turbine blades to advanced nuclear fuel encapsulation, the possibilities are very promising. Aerospace applications are covered in Chapter 9 - Other key areas that are addressed are blast-resistant SiC vehicle/vessel armour in Chapter 8 and wear-resistant SiC ceramics in Chapter 6 - Silicon Carbide Ceramics will be an essential reference resource for academic and industrial researchers and materials scientists and engineers working in ceramic materials for the semiconductor, defence, aerospace, wear resistance and refractory fields - Presents an extensive review of the history, production and properties of SiC ceramics, including their characterization and applications - Discusses classical and state-of-the-art sintering technologies for SiC ceramics - Focuses on the future of ceramic manufacturing and advanced ceramic additive technologies

Download or read book On the perspectives of SiC MOSFETs in high frequency and high power isolated DC DC converters written by Eial Awwad, Abdullah and published by Universitätsverlag der TU Berlin. This book was released on 2020-08-11 with total page 184 pages. Available in PDF, EPUB and Kindle. Book excerpt: Increasing demand for efficiency and power density pushes Si-based devices to some of their inherent material limits, including those related to temperature operation, switching frequency, and blocking voltage. Recently, SiC-based power devices are promising candidates for high-power and high-frequency switching applications. Today, SiC MOSFETs are commercially available from several manufacturers. Although technology affiliated with SiC MOSFETs is improving rapidly, many challenges remain, and some of them are investigated in this work. The research work in this dissertation is divided into the three following parts. Firstly, the static and switching characteristics of the state-of-the-art 1.2 kV planar and double-trench SiC MOSFETs from two different manufacturers are evaluated. The effects of different biasing voltages, DC link voltages, and temperatures are analysed. The characterisation results show that the devices exhibit superior switching performances under different operating conditions. Moreover, several aspects of using the SiC MOSFET’s body diode in a DC/DC converter are investigated, comparing the body-diodes of planar and double-trench devices. Reverse recovery is evaluated in switching tests considering the case temperature, switching rate, forward current, and applied voltage. Based on the measurement results, the junction temperature is estimated to guarantee safe operation. A simple electro-thermal model is proposed in order to estimate the maximum allowed switching frequency based on the thermal design of the SiC devices. Using these results, hard- and soft-switching converters are designed, and devices are characterised as being in continuous operation at a very high switching frequency of 1 MHz. Thereafter, the SiC MOSFETs are operated in a continuous mode in a 10 kW / 100-250 kHz buck converter, comparing synchronous rectification, the use of the body diode, and the use of an external Schottky diode. Further, the parallel operation of the planar devices is considered. Thus, the paralleling of SiC MOSFETs is investigated before comparing the devices in continuous converter operation. In this regard, the impact of the most common mismatch parameters on the static and dynamic current sharing of the transistors is evaluated, showing that paralleling of SiC MOSFETs is feasible. Subsequently, an analytical model of SiC MOSFETs for switching loss optimisation is proposed. The analytical model exhibits relatively close agreement with measurement results under different test conditions. The proposed model tracks the oscillation effectively during both turn-on and –off transitions. This has been achieved by considering the influence of the most crucial parasitic elements in both power and gate loops. In the second part, a comprehensive short-circuit ruggedness evaluation focusing on different failure modes of the planar and double-trench SiC devices is presented. The effects of different biasing voltages, DC link voltages, and gate resistances are evaluated. Additionally, the temperature-dependence of the short-circuit capability is evaluated, and the associated failure modes are analysed. Subsequently, the design and test of two different methods for overcurrent protection are proposed. The desaturation technique is applied to the SiC MOSFETs and compared to a second method that depends on the stray inductance of the devices. Finally, the benefits of using SiC devices in continuous high-frequency, high-power DC/DC converters is experimentally evaluated. In this regard, a design optimisation of a high-frequency transformer is introduced, and the impact of different core materials, conductor designs, and winding arrangements are evaluated. A ZVZCS Phase-Shift Full-Bridge unidirectional DC/DC converter is proposed, using only the parasitic leakage inductance of the transformer. Experimental results for a 10 kW, (100-250) kHz prototype indicate an efficiency of up to 98.1% for the whole converter. Furthermore, an optimized control method is proposed to minimise the circulation current in the isolated bidirectional dual active bridge DC/DC converter, based on a modified dual-phase-shift control method. This control method is also experimentally compared with traditional single-phase shift control, yielding a significant improvement in efficiency. The experimental results confirm the theoretical analysis and show that the proposed control can enhance the overall converter efficiency and expand the ZVZCS range. Die steigende Nachfrage nach Effizienz und Leistungsdichte bringt Si-basierte eistungsbauteile an einige inhärente Materialgrenzen, die unter anderem mit der Temperaturbelastung, der Schaltfrequenz und der Blockierspannung in Zusammenhang stehen. In jüngster Zeit sind SiC-basierte Leistungsbauelemente vielversprechende Kandidaten für Hochleistungs- und Hochfrequenzanwendungen. Aktuell sind SiC-MOSFETs von mehreren Herstellern im Handel erhältlich. Obwohl sich die Technologie der SiC-MOSFETs rasch verbessert, werden viele Herausforderungen bestehen bleiben. Einige dieser Herausforderungen werden in dieser Arbeit untersucht. Die Untersuchungen in dieser Dissertation gliedern sich in die drei folgenden Teile: Im ersten Teil erfolgt, die statische und die transiente Charakterisierung der aktuellen 1,2 kV Planarund Doubletrench SiC-MOSFETs verschiedener Hersteller. Die Auswirkungen unterschiedlicher Gatespannungen, Zwischenkreisspannungen und Temperaturen werden analysiert. Die Ergebnisse der Charakterisierung zeigen, dass die Bauteile überlegene Schaltleistungen unter verschiedenen Betriebsbedingungen aufweisen. Darüber hinaus wird der Einsatz der internen SiC-Bodydioden in einem DC/DC-Wandler untersucht, wobei die Unterschiede zwischen Planar- und Doppeltrench-Bauteilen aufgezeigt werden. Das Reverse-Recovery-Verhalten wird unter Berücksichtigung der Gehäusetemperatur, der Schaltgeschwindigkeit, des Durchlassstroms und der angelegten Spannung bewertet. Anhand der Messergebnisse wird die Sperrschichttemperatur geschätzt, damit ein sicherer Betrieb gewährleistet ist. Ein einfaches elektrothermisches Modell wird vorgestellt, um die maximal zulässige Schaltfrequenz auf der Grundlage des thermischen Designs der SiC-Bauteile abzuschätzen. Anhand dieser Ergebnisse werden hart- und weichschaltende Umrichter konzipiert und die Bauteile werden im Dauerbetrieb mit einer sehr hohen Schaltfrequenz von 1 MHz untersucht. Danach werden die SiC-MOSFETs im Dauerbetrieb in einem 10 kW / 100-250 kHz-Tiefsetzsteller betrieben. Dabei wird die Synchrongleichrichtung, die Verwendung der internen Diode und die Verwendung einer externen Schottky-Diode verglichen. Außerdem wird die Parallelisierung von SiC-MOSFETs untersucht, bevor die Parallelschaltung der verschiedenen Bauelemente ebenso im kontinuierlichen Konverterbetrieb verglichen wird. Es wird der Einfluss der häufigsten Parametervariationen auf die statische und dynamische Stromaufteilung der Transistoren analysiert, was zeigt, dass eine Parallelisierung von SiC-MOSFETs möglich ist. Anschließend wird ein analytisches Modell der SiC-MOSFETs zur Schaltverlustoptimierung vorgeschlagen. Das analytische Modell zeigt eine relativ enge Übereinstimmung mit den Messergebnissen unter verschiedenen Testbedingungen. Das vorgeschlagene Modell bildet die Schwingungen sowohl beim Ein- als auch beim Ausschalten effektiv nach. Dies wurde durch die Berücksichtigung der wichtigsten parasitären Elemente in Strom- und Gatekreisen erreicht. Im zweiten Teil wird eine umfassende Bewertung der Kurzschlussfestigkeit mit Fokus auf verschiedene Ausfallmodi der planaren und double-trench SiC-Bauelemente vorgestellt. Die Auswirkungen unterschiedlicher Gatespannungen, Zwischenkreisspannungen und Gate-Widerstände werden ausgewertet. Zusätzlich wird die temperaturabhängige Kurzschlussfähigkeit ausgewertet und die zugehörigen Fehlerfälle werden analysiert. Anschließend wird die Auslegung und Prüfung von zwei verschiedenen Verfahren zum Überstromschutz evaluiert. Die „Desaturation“-Technik wird auf SiC-MOSFETs angewendet und mit einer zweiten Methode verglichen, welche die parasitäre Induktivität der Bauelemente nutzt. Schließlich wird der Nutzen des Einsatzes von SiC-Bauteilen in kontinuierlichen Hochfrequenz-Hochleistungs-DC/DC-Wandlern experimentell untersucht. In diesem Zusammenhang wird eine Designoptimierung eines Hochfrequenztransformators vorgestellt und der Einfluss verschiedener Kernmaterialien, Leiterausführungen und Wicklungsanordnungen wird bewertet. Es wird ein unidirektionaler ZVZCS Vollbrücken-DC/DC-Wandler vorgestellt, der nur die parasitäre Streuinduktivität des Transformators verwendet. Experimentelle Ergebnisse für einen 10 kW, (100-250) kHz Prototyp zeigen einenWirkungsgrad von bis zu 98,1% für den gesamten Umrichter. Abschließend wird ein optimiertes Regelverfahren verwendet, welches auf einem modifizierten Dual-Phase-Shift-Regelverfahren basiert, um den Kreisstrom im isolierten bidirektionalen Dual-Aktiv-Brücken-DC/DC-Wandler zu minimieren. Diese Regelmethode wird experimentell mit der herkömmlichen Single-Phase-Shift-Regelung verglichen. Hierbei zeigt sich eine deutliche Effizienzsteigerung durch die neue Regelmethode. Die experimentellen Ergebnisse bestätigen die theoretische Analyse und zeigen, dass die vorgeschlagene Regelung den Gesamtwirkungsgrad des Umrichters erhöhen und den ZVZCS-Bereich erweitern kann.

Download or read book SiC based Miniaturized Devices written by Stephen Edward Saddow and published by MDPI. This book was released on 2020-06-18 with total page 170 pages. Available in PDF, EPUB and Kindle. Book excerpt: MEMS devices are found in many of today’s electronic devices and systems, from air-bag sensors in cars to smart phones, embedded systems, etc. Increasingly, the reduction in dimensions has led to nanometer-scale devices, called NEMS. The plethora of applications on the commercial market speaks for itself, and especially for the highly precise manufacturing of silicon-based MEMS and NEMS. While this is a tremendous achievement, silicon as a material has some drawbacks, mainly in the area of mechanical fatigue and thermal properties. Silicon carbide (SiC), a well-known wide-bandgap semiconductor whose adoption in commercial products is experiening exponential growth, especially in the power electronics arena. While SiC MEMS have been around for decades, in this Special Issue we seek to capture both an overview of the devices that have been demonstrated to date, as well as bring new technologies and progress in the MEMS processing area to the forefront. Thus, this Special Issue seeks to showcase research papers, short communications, and review articles that focus on: (1) novel designs, fabrication, control, and modeling of SiC MEMS and NEMS based on all kinds of actuation mechanisms; and (2) new developments in applying SiC MEMS and NEMS in consumer electronics, optical communications, industry, medicine, agriculture, space, and defense.

Download or read book The proceedings of the 10th Frontier Academic Forum of Electrical Engineering FAFEE2022 written by Qingxin Yang and published by Springer Nature. This book was released on 2023-09-14 with total page 1290 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book includes the original, peer-reviewed research papers from the 10th Frontier Academic Forum of Electrical Engineering (FAFEE 2022), held in Xi’an, China, in August 2022. It gathers the latest research, innovations, and applications in the fields of Electrical Engineering. The topics it covers include electrical materials and equipment, electrical energy storage and device, power electronics and drives, new energy electric power system equipment, IntelliSense and intelligent equipment, biological electromagnetism and its applications, and insulation and discharge computation for power equipment. Given its scope, the book benefits all researchers, engineers, and graduate students who want to learn about cutting-edge advances in Electrical Engineering.

Download or read book High Power Converters and AC Drives written by Bin Wu and published by John Wiley & Sons. This book was released on 2017-01-17 with total page 476 pages. Available in PDF, EPUB and Kindle. Book excerpt: A comprehensive reference of the latest developments in MV drive technology in the area of power converter topologies This new edition reflects the recent technological advancements in the MV drive industry, such as advanced multilevel converters and drive configurations. It includes three new chapters, Control of Synchronous Motor Drives, Transformerless MV Drives, and Matrix Converter Fed Drives. In addition, there are extensively revised chapters on Multilevel Voltage Source Inverters and Voltage Source Inverter-Fed Drives. This book includes a systematic analysis on a variety of high-power multilevel converters, illustrates important concepts with simulations and experiments, introduces various megawatt drives produced by world leading drive manufacturers, and addresses practical problems and their mitigations methods. This new edition: Provides an in-depth discussion and analysis of various control schemes for the MV synchronous motor drives Examines new technologies developed to eliminate the isolation transformer in the MV drives Discusses the operating principle and modulation schemes of matrix converter (MC) topology and multi-module cascaded matrix converters (CMCs) for MV drives, and their application in commercial MV drives Bin Wu is a Professor and Senior NSERC/Rockwell Automation Industrial Research Chair in Power Electronics and Electric Drives at Ryerson University, Canada. He is a fellow of Institute of Electrical and Electronics Engineers (IEEE), Engineering Institute of Canada (EIC), and Canadian Academy of Engineering (CAE). Dr. Wu has published more than 400 papers and holds more than 30 granted/pending US/European patents. He co-authored several books including Power Conversion and Control of Wind Energy Systems and Model Predictive Control of Wind Energy Conversion Systems (both by Wiley-IEEE Press). Mehdi Narimani is a Postdoctoral Research Associate with the Department of Electrical and computer Engineering at Ryerson University, Canada, and Rockwell Automation Canada. He is a senior member of IEEE. Dr. Narimani is author/co-author of more than 50 technical papers and four US/European patents (issued/pending review). His current research interests include power conversion, high power converters, control of power electronics, and renewable energy systems.

Download or read book Digital Technologies and Applications written by Saad Motahhir and published by Springer Nature. This book was released on with total page 572 pages. Available in PDF, EPUB and Kindle. Book excerpt: