Download or read book Damage Detection in Carbon Fiber Composites Using Electrical Resistance Measurements written by Ryan Steven Gory and published by . This book was released on 2012 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: ABSTRACT: This thesis proposes a methodology for structural health monitoring that incorporates the inherent multi-functionality of carbon fibers. The hypothesis of the thesis is that by monitoring the electrical resistance of composite panels it is possible to detect impacts and statistically model their effects on the remaining useful service life of structures. The proposed research investigates the application of statistics-based analysis to the measured electrical resistance signals during loading. The research also investigates the use of electrical resistance as a stress sensor by monitoring the resistance of test samples under tensile loading.

Download or read book Damage Detection in Composite Interfaces Through Carbon Nanotube Reinforcement written by and published by . This book was released on 2010 with total page 84 pages. Available in PDF, EPUB and Kindle. Book excerpt: Use of carbon nanotubes along composite interfaces was studied to both improve fracture strength and monitor interfacial damage progression. Both carbon fiber and E-glass fiber composites were manufactured with vinyl ester resin using vacuum-assisted resin transfer molding. First, the effects of single-step curing (i.e., co-curing) versus two-step curing (i.e., curing a new section to a previously cured section) was studied using Mode II fracture testing. The results showed the two-step cured interface was as strong as the co-cured interface, thus validating the use of two-step curing during modular construction or repair of composite sections. Application of carbon nanotubes to the composite interfaces was then accomplished through two-step curing, using acetone as a dispersant. Mode II testing indicated significant improvement of the interface fracture toughness for both carbon fiber and glass fiber samples with carbon nanotubes. Because carbon nanotubes have very high electrical conductivity, the electrical resistance was measured across the interface during Mode II loading. As the interface crack grew, there was an increase in electrical resistance (approximately linear for carbon fiber specimens until final failure). The study demonstrated the feasibility of electrical resistance measurement with dispersed carbon nanotubes to monitor damage along critical interfaces, while simultaneously improving fracture properties.

Download or read book Electrical Contacts written by Milenko Braunovic and published by CRC Press. This book was released on 2017-12-19 with total page 672 pages. Available in PDF, EPUB and Kindle. Book excerpt: Various factors affect the performance of electrical contacts, including tribological, mechanical, electrical, and materials aspects. Although these behaviors have been studied for many years, they are not widely used or understood in practice. Combining approaches used across the globe, Electrical Contacts: Fundamentals, Applications, and Technology integrates advances in research and development in the tribological, material, and analytical aspects of electrical contacts with new data on electrical current transfer at the micro- and nanoscales. Taking an application-oriented approach, the authors illustrate how material characteristics, tribological behavior, and loading impact the degradation of contacts, formation of intermetallics, and overall reliability and performance. Coverage is divided broadly into three sections, with the first focused on mechanics, tribology, materials, current and heat transfer, and basic reliability issues of electrical contacts. The next section explores applications, such as power connections, electronic connections, and sliding contacts, while the final section presents the diagnostic and monitoring techniques used to investigate and measure phenomena occurring at electrical contact interfaces. Numerous references to current literature reflect the fact that this book is the most comprehensive survey in the field. Explore an impressive collection of data, theory, and practical applications in Electrical Contacts: Fundamentals, Applications, and Technology, a critical tool for anyone investigating or designing electrical equipment with improved performance and reliability in mind.

Download or read book Nondestructive Testing and Evaluation of Fiber Reinforced Composite Structures written by Shuncong Zhong and published by Springer Nature. This book was released on 2022-04-01 with total page 431 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a detailed description of the most common nondestructive testing(NDT) techniques used for the testing and evaluation fiber-reinforced composite structures, during manufacturing and/or in service stages. In order to facilitate the understanding and the utility of the different NDT techniques presented, the book first provides some information regarding the defects and material degradation mechanisms observed in fiber-reinforced composite structures as well as their general description and most probable causes. It is written based on the extensive scientific research and engineering backgrounds of the authors in the NDT and structural health monitoring (SHM) of structural systems from various areas including electrical, mechanical, materials, civil and biomedical engineering. Pursuing a rigorous approach, the book establishes a fundamental framework for the NDT of fiber-reinforced composite structures, while emphasizing on the importance of technique’s spatial resolution, integrated systems analysis and the significance of the influence stemming from the applicability of the NDT and the physical parameters of the test structures in the selection and utilization of adequate NDT techniques. The book is intended for students who are interested in the NDT of fiber-reinforced composite structures, researchers investigating the applicability of different NDT techniques to the inspections of structural systems, and NDT researchers and engineers working on the optimization of NDT systems for specific applications involving the use of fiber-reinforced composite structures.

Download or read book Structural Health Monitoring of Aerospace Composites written by Victor Giurgiutiu and published by Academic Press. This book was released on 2015-09-08 with total page 471 pages. Available in PDF, EPUB and Kindle. Book excerpt: Structural Health Monitoring of Aerospace Composite Structures offers a comprehensive review of established and promising technologies under development in the emerging area of structural health monitoring (SHM) of aerospace composite structures. Beginning with a description of the different types of composite damage, which differ fundamentally from the damage states encountered in metallic airframes, the book moves on to describe the SHM methods and sensors currently under consideration before considering application examples related to specific composites, SHM sensors, and detection methods. Expert author Victor Giurgiutiu closes with a valuable discussion of the advantages and limitations of various sensors and methods, helping you to make informed choices in your structure research and development. - The first comprehensive review of one of the most ardent research areas in aerospace structures, providing breadth and detail to bring engineers and researchers up to speed on this rapidly developing field - Covers the main classes of SHM sensors, including fiber optic sensors, piezoelectric wafer active sensors, electrical properties sensors and conventional resistance strain gauges, and considers their applications and limitation - Includes details of active approaches, including acousto-ultrasonics, vibration, frequency transfer function, guided-wave tomography, phased arrays, and electrochemical impedance spectroscopy (ECIS), among other emerging methods

Download or read book Impact Damage Sensing in Carbon Fiber Polymer matrix Composite Plates Via Electrical Resistance Measurement written by Justin McAndrew and published by . This book was released on 2009 with total page 500 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Experimental and Applied Mechanics Volume 6 written by Nancy Sottos and published by Springer. This book was released on 2014-08-02 with total page 202 pages. Available in PDF, EPUB and Kindle. Book excerpt: Experimental and Applied Mechanics, Volume 6: Proceedings of the 2014 Annual Conference on Experimental and Applied Mechanics, the sixth volume of eight from the Conference, brings together contributions to important areas of research and engineering. The collection presents early findings and case studies on a wide range of topics, including: Advances in Residual Stress Measurement Methods Residual Stress Effects on Material Performance Inverse Problems and Hybrid Techniques Thermoelastic Stress Analysis Infrared Techniques Research in Progress Applications in Experimental Mechanics

Download or read book Polymer Composites for Electrical Engineering written by Xingyi Huang and published by John Wiley & Sons. This book was released on 2021-11-01 with total page 452 pages. Available in PDF, EPUB and Kindle. Book excerpt: Explore the diverse electrical engineering application of polymer composite materials with this in-depth collection edited by leaders in the field Polymer Composites for Electrical Engineering delivers a comprehensive exploration of the fundamental principles, state-of-the-art research, and future challenges of polymer composites. Written from the perspective of electrical engineering applications, like electrical and thermal energy storage, high temperature applications, fire retardance, power cables, electric stress control, and others, the book covers all major application branches of these widely used materials. Rather than focus on polymer composite materials themselves, the distinguished editors have chosen to collect contributions from industry leaders in the area of real and practical electrical engineering applications of polymer composites. The books relevance will only increase as advanced polymer composites receive more attention and interest in the area of advanced electronic devices and electric power equipment. Unique amongst its peers, Polymer Composites for Electrical Engineering offers readers a collection of practical and insightful materials that will be of great interest to both academic and industrial audiences. Those resources include: A comprehensive discussion of glass fiber reinforced polymer composites for power equipment, including GIS, bushing, transformers, and more) Explorations of polymer composites for capacitors, outdoor insulation, electric stress control, power cable insulation, electrical and thermal energy storage, and high temperature applications A treatment of semi-conductive polymer composites for power cables In-depth analysis of fire-retardant polymer composites for electrical engineering An examination of polymer composite conductors Perfect for postgraduate students and researchers working in the fields of electrical, electronic, and polymer engineering, Polymer Composites for Electrical Engineering will also earn a place in the libraries of those working in the areas of composite materials, energy science and technology, and nanotechnology.

Download or read book American Society of Composites 28th Technical Conference written by Charles Bakis and published by DEStech Publications, Inc. This book was released on 2013-11-01 with total page 1892 pages. Available in PDF, EPUB and Kindle. Book excerpt: New and unpublished U.S. and international research on multifunctional, active, biobased, SHM, self-healing composites -- from nanolevel to large structures New information on modeling, design, computational engineering, manufacturing, testing Applications to aircraft, bridges, concrete, medicine, body armor, wind energy This fully searchable CD-ROM contains 135 original research papers on all phases of composite materials. The document provides cutting edge research by US, Canadian, and Japanese authorities on matrix-based and fiber composites from design to damage analysis and detection. Major divisions of the work include: Structural Health Monitoring, Multifunctional Composites, Integrated Computational Materials Engineering, Interlaminar Testing, Analysis-Shell Structures, Thermoplastic Matrices, Analysis Non-classical Laminates, Bio-Based Composites, Electrical Properties, Dynamic Behavior, Damage/Failure, Compression-Testing, Active Composites, 3D Reinforcement, Dielectric Nanocomposites, Micromechanical Analysis, Processing, CM Reinforcement for Concrete, Environmental Effects, Phase-Transforming, Molecular Modeling, Impact.

Download or read book Carbon Nanotube Enhanced Aerospace Composite Materials written by A. Paipetis and published by Springer Science & Business Media. This book was released on 2012-09-14 with total page 381 pages. Available in PDF, EPUB and Kindle. Book excerpt: The well documented increase in the use of high performance composites as structural materials in aerospace components is continuously raising the demands in terms of dynamic performance, structural integrity, reliable life monitoring systems and adaptive actuating abilities. Current technologies address the above issues separately; material property tailoring and custom design practices aim to the enhancement of dynamic and damage tolerance characteristics, whereas life monitoring and actuation is performed with embedded sensors that may be detrimental to the structural integrity of the component. This publication explores the unique properties of carbon nanotubes (CNT) as an additive in the matrix of Fibre Reinforced Plastics (FRP), for producing structural composites with improved mechanical performance as well as sensing/actuating capabilities. The successful combination of the CNT properties and existing sensing actuating technologies leads to the realization of a multifunctional FRP structure. The current volume presents the state of the art research in this field. The contributions cover all the aspects of the novel composite systems, i.e. modeling from nano to macro scale, enhancement of structural efficiency, dispersion and manufacturing, integral health monitoring abilities, Raman monitoring, as well as the capabilities that ordered carbon nanotube arrays offer in terms of sensing and/or actuating in aerospace composites.

Download or read book American Society for Composites American Society for Testing And Materials Committee D30 written by Erian Armanios and published by DEStech Publications, Inc. This book was released on 2004-10 with total page 1464 pages. Available in PDF, EPUB and Kindle. Book excerpt: Highlights the recent developments in the fundamental understanding of composites; important information for researchers and composite scientists.

Download or read book Non destructive Testing of Impact Damage in Fiber reinforced Polymer Composites written by Milad Saeedifar and published by Elsevier. This book was released on 2024-08-08 with total page 333 pages. Available in PDF, EPUB and Kindle. Book excerpt: Non-destructive Testing of Impact Damage in Fiber-reinforced Polymer Composites: Fundamentals and Applications provides detailed knowledge on the fundamentals and applications of frequently used nondestructive testing (NDT) techniques utilized to assess impact damage in composite structures. This book starts with an introduction to impact damage in composite structures, each subsequent chapter focuses on evaluating damage using specific NDT methods. Chapters 2–4 concentrate on vision-based NDT methods such as visual inspection, digital image correlation, and digital shearography. Following this, Chapters 5–6 delve into ultrasound-based methods, including acoustic emission and phased-array ultrasonic inspection. Radiation-based methods, micro-CT, and thermography are discussed in Chapters 7 and 8, while Chapters 9 and 10 elucidate microwave inspection and electrical impedance tomography. This book is a useful reference for both academia and industry and covers the fundamentals, practical tips, case studies, and applications, as well as current research trends and future possibilities, for each technique. - Insights into the diverse damage levels in composite materials resulting from low-velocity impact, ranging from micro matrix cracks to severe delamination and fiber breakage - Covers a broad range of NDT techniques, including recently developed NDT techniques, suitable for detecting impact damage in composite materials - Serves as a valuable reference for both academia and industry, providing comprehensive coverage of fundamental principles, practical insights, applications, case studies, current research trends, and future prospects for each NDT technique

Download or read book Emerging Technologies in NDT written by Gerhard Busse and published by CRC Press. This book was released on 2008-04-16 with total page 380 pages. Available in PDF, EPUB and Kindle. Book excerpt: Non-destructive testing (NDT) is a pertinent task in nearly every field of human activity, from the assuring of aircraft integrity to the evaluation of infrastructural decay caused by deterioration or damage. The development of non-destructive methods for quality management results in economic and environmental benefits, in an increase in product reliability, and in improved public safety and security. This book contains over fifty reviewed and edited papers on the innovative developments and new applications in NDT. It covers cutting-edge NDT methods, including optical, acoustic, ultrasonic, and electromagnetic techniques, tomography, radiography, and thermography. Intended for a researchers and practitioners involved with studying, testing and maintaining machinery, products and components in laboratory and industrial environments.

Download or read book Damage Detection of Carbon Fiber Reinforced Polymer Using Electrical Measurement and Analysis of Acoustic Emission Signals written by Heng-Hsueh Chen and published by . This book was released on 2013 with total page 73 pages. Available in PDF, EPUB and Kindle. Book excerpt: Carbon fiber reinforced polymer composites (CFRPs) have been widely used in aerospace, civil engineering and so on in recent decades because of their excellent mechanical properties (high strength and stiffness), low density, long-term durability and high resistances to corrosion, pressure and other harsh environment conditions. Since CFRPs are multiphase materials that consist of polymer matrix and carbon fibers plies. Local separation between plies and/or debonding at fiber-matrix interface may occur during application. Damage in this form of delamination may affect the material properties such as the ability of stress transmission, which leads to component failure in the vehicles or even disastrous loss. Hence, the study of damage detection is necessary to ensure the safety use of CFRPs. In this thesis, we first introduce the tensile test for CFRP sample. The test is conducted by hydraulic wedge grip with electrical potential measurement and acoustic emission sensors, respectively. Continuous wavelet transform is applied to analyze output signals, which enables us to see the differences between unbroken and broken samples. Electrical potential measurement provides direct information from the original output signal about the sample damage, and there is no external sensors needed. Acoustic emission method, on the other hand, helps us to make hypothesis on recognizing different failure modes. Then we study the impact of damage in the form of delamiantion and the damage in the form of hole. By measuring the electrical potential, we estimate the damage location experimentally, and the linear relationship between damage dimension ratio and average/maximum ratio of potential change is developed to estimate the damage size. Then via 3D FEA modeling, we study the undamaged and damaged cases numerically with the same conditions as in the experimental study, and the electrical potential distributions are obtained to evaluate the damage. The numerical result shows good agreement with the experimental result.

Download or read book Carbon Composites written by Deborah D.L. Chung and published by Butterworth-Heinemann. This book was released on 2016-11-08 with total page 708 pages. Available in PDF, EPUB and Kindle. Book excerpt: Carbon Composites: Composites with Carbon Fibers, Nanofibers, and Nanotubes, Second Edition, provides the reader with information on a wide range of carbon fiber composites, including polymer-matrix, metal-matrix, carbon-matrix, ceramic-matrix and cement-matrix composites. In contrast to other books on composites, this work emphasizes materials rather than mechanics. This emphasis reflects the key role of materials science and engineering in the development of composite materials. The applications focus of the book covers both the developing range of structural applications for carbon fiber composites, including military and civil aircraft, automobiles and construction, and non-structural applications, including electromagnetic shielding, sensing/monitoring, vibration damping, energy storage, energy generation, and deicing. In addition to these new application areas, new material in this updated edition includes coverage of cement-matrix composites, carbon nanofibers, carbon matrix precursors, fiber surface treatment, nanocarbons, and hierarchical composites. An ideal source of information for senior undergraduate students, graduate students, and professionals working with composite materials and carbon fibers, this book can be used both as a reference book and as a textbook. Introduces the entire spectrum of carbon fiber composites, including polymer-matrix, metal-matrix, carbon-matrix, ceramic-matrix and cement-matrix composites Systematically sets out the processing, properties, and applications of each type of material Emphasizes processing as the foundation of understanding, manufacturing, and designing with composite materials

Download or read book Proceedings of the American Society for Composites 2014 Twenty ninth Technical Conference on Composite Materials written by Hyonny Kim and published by DEStech Publications, Inc. This book was released on 2014-09-17 with total page 3583 pages. Available in PDF, EPUB and Kindle. Book excerpt: New and not previously published U.S. and international research on composite and nanocomposite materialsFocus on health monitoring/diagnosis, multifunctionality, self-healing, crashworthiness, integrated computational materials engineering (ICME), and moreApplications to aircraft, armor, bridges, ships, and civil structures This fully searchable CD-ROM contains 270 original research papers on all phases of composite materials, presented by specialists from universities, NASA and private corporations such as Boeing. The document is divided into the following sections: Aviation Safety and Aircraft Structures; Armor and Protection; Multifunctional Composites; Effects of Defects; Out of Autoclave Processing; Sustainable Processing; Design and Manufacturing; Stability and Postbuckling; Crashworthiness; Impact and Dynamic Response; Natural, Biobased and Green; Integrated Computational Materials Engineering (ICME); Structural Optimization; Uncertainty Quantification; NDE and SHM Monitoring; Progressive Damage Modeling; Molecular Modeling; Marine Composites; Simulation Tools; Interlaminar Properties; Civil Structures; Textiles. The CD-ROM displays figures and illustrations in articles in full color along with a title screen and main menu screen. Each user can link to all papers from the Table of Contents and Author Index and also link to papers and front matter by using the global bookmarks which allow navigation of the entire CD-ROM from every article. Search features on the CD-ROM can be by full text including all key words, article title, author name, and session title. The CD-ROM has Autorun feature for Windows 2000 or higher products and can also be used with Macintosh computers. The CD includes the program for Adobe Acrobat Reader with Search 11.0. One year of technical support is included with your purchase of this product.

Download or read book Structural Health Monitoring 2003 written by Fu-Kuo Chang and published by DEStech Publications, Inc. This book was released on 2003 with total page 1592 pages. Available in PDF, EPUB and Kindle. Book excerpt: Important new information on sensors, monitoring, prognosis, networking, and planning for safety and maintenance.