Download or read book CVD Silicon Carbide Monofilament Reinforced SrO Al2O3 2SiO2 SAS Glass Ceramic Composites written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-08-20 with total page 44 pages. Available in PDF, EPUB and Kindle. Book excerpt: Unidirectional CVD SiC fiber-reinforced SrO.Al2O3.2SiO2 (SAS) glass-ceramic matrix composites have been fabricated by hot pressing at various combinations of temperature, pressure and time. Both carbon-rich surface coated SCS-6 and uncoated SCS-0 fibers were used as reinforcements. Almost fully dense composites have been obtained. Monoclinic celsian, SrAl2Si2O8, was the only crystalline phase observed in the matrix from x-ray diffraction. During three point flexure testing of composites, a test span to thickness ratio of approximately 25 or greater was necessary to avoid sample delamination. Strong and tough SCS-6/SAS composites having a first matrix crack stress of approximately 300 MPa and an ultimate bend strength of approximately 825 MPa were fabricated. No chemical reaction between the SCS-6 fibers and the SAS matrix was observed after high temperature processing. The uncoated SCS-0 fiber-reinforced SAS composites showed only limited improvement in strength over SAS monolithic. The SCS-0/SAS composite having a fiber volume fraction of 0.24 and hot pressed at 1400 deg C exhibited a first matrix cracking stress of approximately 231 +/- 20 MPa and ultimate strength of 265 +/- 17 MPa. From fiber push-out tests, the fiber/matrix interfacial debonding strength (tau(sub debond)) and frictional sliding stress (tau(sub friction)) in the SCS-6/SAS system were evaluated to be approximately 6.7 +/- 2.3 MPa and 4.3 +/- 0.6 MPa, respectively, indicating a weak interface. However, for the SCS-0/SAS composite, much higher values of approximately 17.5 +/- 2.7 MPa for tau(sub debond) and 11.3 +/- 1.6 MPa for tau(sub friction) respectively, were observed; some of the fibers were so strongly bonded to the matrix that they could not be pushed out. Examination of fracture surfaces revealed limited short pull-out length of SCS-0 fibers. The applicability of various micromechanical models for predicting the values of first matrix cracking stress and ultimate strength of these composit...
Download or read book CVD Silicon Carbide Monofilament Reinforced SrO Al2O3 2SiO2 SAS Glass ceramic Composites written by and published by . This book was released on 1995 with total page 44 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book 20th Annual Conference on Composites Advanced Ceramics Materials and Structures B Volume 17 Issue 4 written by John B. Wachtman and published by John Wiley & Sons. This book was released on 2009-09-28 with total page 469 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume is part of the Ceramic Engineering and Science Proceeding (CESP) series. This series contains a collection of papers dealing with issues in both traditional ceramics (i.e., glass, whitewares, refractories, and porcelain enamel) and advanced ceramics. Topics covered in the area of advanced ceramic include bioceramics, nanomaterials, composites, solid oxide fuel cells, mechanical properties and structural design, advanced ceramic coatings, ceramic armor, porous ceramics, and more.
Download or read book Effects of Fiber Content on Mechanical Properties of CVD SiC Fiber Reinforced Strontium Aluminosilicate Glass Ceramic Composites written by Narottam P. Bansal and published by . This book was released on 1996 with total page 30 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Monthly Catalog of United States Government Publications written by and published by . This book was released on 1996-07 with total page 1000 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Ceramic Matrix Composites written by Krishan K. Chawla and published by Springer Science & Business Media. This book was released on 2013-11-27 with total page 449 pages. Available in PDF, EPUB and Kindle. Book excerpt: After an introductory chapter, the processing, microstructure, and properties of various ceramic materials, reinforcements, and their composites are described. A separate chapter is devoted to processing of ceramic reinforcements, with a special emphasis on fibers. Processing of ceramic matrix composites is the next chapter, which includes novel techniques such as sol-gel processing and ceramics from polymeric precursors. The next four chapters cover the subjects of interface region in ceramic composites, mechanical and physical properties, and the role of thermal stresses and the important subject of toughness enhancement. Laminated composites made of ceramics are described in a separate chapter. Finally, a chapter is devoted to various applications of ceramic matrix composites. Throughout the text, the underlying relationships between the components of the triad: processing, microstructure, and properties are brought out. An exhaustive list of references and suggested reading is provided.
Download or read book Proceedings of the 20th Annual Conference on Composites Advanced Ceramics Materials and Structures written by and published by . This book was released on 1996 with total page 652 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Handbook of Ceramic Composites written by Narottam P. Bansal and published by Springer Science & Business Media. This book was released on 2006-08-25 with total page 547 pages. Available in PDF, EPUB and Kindle. Book excerpt: This valuable handbook has been compiled by internationally renowned researchers in the field. Each chapter is focused on a specific composite system or a class of composites, presenting a detailed description of processing, properties, and applications.
Download or read book Fiber Reinforced Ceramic Composites written by K.S. Mazdiyasni and published by William Andrew. This book was released on 1990-12-31 with total page 546 pages. Available in PDF, EPUB and Kindle. Book excerpt: Provides the first comprehensive treatment of continuous and discontinuous ceramic fiber and whisker reinforced ceramic composites, written by 29 authorities in the field.
Download or read book Effects of Fiber Content on Mechanical Properties of CVD SiC Fiber Reinforced Strontium Aluminosilicate Glass Ceramic Composites written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-07-02 with total page 30 pages. Available in PDF, EPUB and Kindle. Book excerpt: Unidirectional CVD SiC(f)(SCS-6) fiber-reinforced strontium aluminosilicate (SAS) glass-ceramic matrix composites containing various volume fractions, approximately 16 to 40 volume %, of fibers were fabricated by hot pressing at 1400 C for 2 h under 27.6 MPa. Monoclinic celsian, SrAl2Si2O8, was the only crystalline phase formed, with complete absence of the undesired hexacelsian phase, in the matrix. Room temperature mechanical properties were measured in 3-point flexure. The matrix microcracking stress and the ultimate strength increased with increase in fiber volume fraction, reached maximum values for V(sub f) approximately equal to 0.35, and degraded at higher fiber loadings. This degradation in mechanical properties is related to the change in failure mode, from tensile at lower V(sub f) to interlaminar shear at higher fiber contents. The extent of fiber loading did not have noticeable effect on either fiber-matrix debonding stress, or frictional sliding stress at the interface. The applicability of micromechanical models in predicting the mechanical properties of the composites was also examined. The currently available theoretical models do not appear to be useful in predicting the values of the first matrix cracking stress, and the ultimate strength of the SCS-6/SAS composites. Bansal, Narottam P. Glenn Research Center RTOP 505-63-12...
Download or read book High Temperature Ceramic Matrix Composites written by R. Naslain and published by Woodhead Publishing Limited. This book was released on 1993 with total page 864 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book High Temperature Ceramic Matrix Composites written by Walter Krenkel and published by Wiley-VCH. This book was released on 2001 with total page 1044 pages. Available in PDF, EPUB and Kindle. Book excerpt: The extreme high temperature stability and damage tolerance of materials and components required for space, terrestrial, energetic and many other applications can only be achieved by ceramic materials. All over the world research is going on to develop ceramics with quasiductile behaviour. The materials with the highest potential for high temperature applications are fibre reinforced ceramic matrix composites (CMC). The international conference HT-CMC 4 in Munich will continue the tradition of its successful predecessor meetings held in Bordeaux (France, 1993), Santa Barbara (USA, 1995) and Osaka (Japan, 1998). This conference series has been recognized as the central meeting event in high temperature CMC science and technology and demonstrates the great interest in research and development on reinforced ceramics. The Proceedings of this conference will therefore be a valuable reference for every materials scientist or engineer involved in this field of high-tech materials development.
Download or read book Silicon Carbide Fiber Reinforced Glass ceramic Composites in the Zirconia magnesium Aluminosilicate System written by Valerie Jean Powers and published by . This book was released on 1986 with total page 192 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Research and Technology 1992 written by and published by . This book was released on 1992 with total page 176 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Government Reports Announcements Index written by and published by . This book was released on 1996 with total page 748 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Ceramics and Composites Processing Methods written by Narottam P. Bansal and published by John Wiley & Sons. This book was released on 2012-04-17 with total page 598 pages. Available in PDF, EPUB and Kindle. Book excerpt: Examines the latest processing and fabrication methods There is increasing interest in the application of advanced ceramic materials in diverse areas such as transportation, energy, environmental protection and remediation, communications, health, and aerospace. This book guides readers through a broad selection of key processing techniques for ceramics and their composites, enabling them to manufacture ceramic products and components with the properties needed for various industrial applications. With chapters contributed by internationally recognized experts in the field of ceramics, the book includes traditional fabrication routes as well as new and emerging approaches in order to meet the increasing demand for more reliable ceramic materials. Ceramics and Composites Processing Methods is divided into three sections: * Densification, covering the fundamentals and practice of sintering, pulsed electric current sintering, and viscous phase silicate processing * Chemical Methods, examining colloidal methods, sol-gel, gel casting, polymer processing, chemical vapor deposition, chemical vapor infiltration, reactive melt infiltration, and combustion synthesis * Physical Methods, including directional solidification, solid free-form fabrication, microwave processing, electrophoretic deposition, and plasma spraying Each chapter focuses on a particular processing method or approach. Collectively, these chapters offer readers comprehensive, state-of-the-science information on the many approaches, techniques, and methods for the processing and fabrication of advanced ceramics and ceramic composites. With its coverage of the latest processing methods, Ceramics and Composites Processing Methods is recommended for researchers and students in ceramics, materials science, structural materials, biomedical engineering, and nanotechnology.
Download or read book Handbook of Glass Properties written by Narottam P. Bansal and published by Elsevier. This book was released on 2013-10-22 with total page 691 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume is a compilation of data on the properties of glasses. The authors have critically examined and correlated the most reliable data on the properties of multicomponent commercial silicate glasses, vitreous silica, and binary and ternary laboratory glasses. Thermodynamic, thermal, mechanical, electrical, and transport properties are covered. Measurement methods and appropriate theories are also discussed.
