Download or read book Crack Initiation in Low Alloy Steel in High Temperature Water written by RE. DeLair and published by . This book was released on 1997 with total page 15 pages. Available in PDF, EPUB and Kindle. Book excerpt: This paper describes a study of fatigue crack initiation in WB36, a German low alloy steel, tested in high temperature, high purity, water. Flat un-notched, tensile specimens were cycled under load control, with R=0.1, and with a saw-tooth wave form (with a loading time of 30 seconds and an unloading time of 3 seconds). Crack initiation was followed by periodically stopping the test and replicating the surface. The tests were performed at 177°C, in water containing 8ppm O2. H2SO4 additions were also made in some tests to raise the conductivity of the water from 0.06 ?S/cm to 0.4-0.5?S/cm. The crack initiation and growth data are correlated with the water chemistry of the test.

Download or read book Effects of the Environment on the Initiation of Crack Growth written by William Alan Van der Sluys and published by ASTM International. This book was released on 1997 with total page 304 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Crack Initiation and Crack Growth Behavior of Carbon and Low alloy Steels written by and published by . This book was released on 2001 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Section III of the ASME Boiler and Pressure Vessel Code specifies fatigue design curves for structural materials. These curves were based on tests of smooth polished specimens at room temperature in air. The effects of reactor coolant environments are not explicitly addressed by the Code design curves, but recent test data illustrate potentially significant effects of LWR coolant environments on the fatigue resistance of carbon and low-alloy steels. Under certain loading and environmental conditions, fatigue lives of test specimens may be a factor of[approx]70 shorter than in air. Results of fatigue tests that examine the influence of reactor environment on crack imitation and crack growth of carbon and low-alloy steels are presented. Crack lengths as a function of fatigue cycles were determined in air by a surface replication technique, and in water by block loading that leaves marks on the fracture surface. Decreases in fatigue life of low-alloy steels in high-dissolved-oxygen (DO) water are primarily caused by the effects of environment during early stages of fatigue damage, i.e., growth of short cracks100[micro]m in depth. For crack sizes of100[micro]m, crack growth rates in high-DO water are higher than in air by one order of magnitude. The effects of LWR environments on growth of short cracks are discussed.

Download or read book The Effect of Aqueous Environments Upon the Initiation and Propagation of Fatigue Cracks in Low alloy Steels written by and published by . This book was released on 1996 with total page 34 pages. Available in PDF, EPUB and Kindle. Book excerpt: The effect of elevated temperature aqueous environments upon the initiation and propagation of fatigue cracks in low-alloy steels is discussed in terms of the several parameters which influence such behavior. These parameters include water chemistry, impurities within the steels themselves, as well as factors such as the water flow rate, loading waveform and loading rates. Some of these parameters have similar effects upon both crack initiation and propagation, while others exhibit different effects in the two stages of cracking. In the case of environmentally-assisted crack (EAC) growth, the most important impurities within the steel are metallurgical sulfide inclusions which dissolve upon contact with the water. A ''critical'' concentration of sulfide ions at the crack tip can then induce environmentally-assisted cracking which proceeds at significantly increased crack growth rates over those observed in air. The occurrence, or non-occurrence, of EAC is governed by the mass-transport of sulfide ions to and from the crack-tip region, and the mass-transport is discussed in terms of diffusion, ion migration, and convection induced within the crack enclave. Examples are given of convective mass-transport within the crack enclave resulting from external free stream flow. The initiation of fatigue cracks in elevated temperature aqueous environments, as measured by the S-N fatigue lifetimes, is also strongly influenced by the parameters identified above. The influence of sulfide inclusions does not appear to be as strong on the crack initiation process as it is on crack propagation. The oxygen content of the environment appears to be the dominant factor, although loading frequency (strain rate) and temperature are also important factors.

Download or read book Fatigue Crack Initiation in Carbon and Low alloy Steels in Light Water Reactor Environments written by and published by . This book was released on 1998 with total page 23 pages. Available in PDF, EPUB and Kindle. Book excerpt: Section 111 of the ASME Boiler and Pressure Vessel Code specifies fatigue design curves for structural materials. The effects of reactor coolant environments are not explicitly addressed by the Code design curves. Recent test data illustrate potentially significant effects of light water reactor (LWR) coolant environments on the fatigue resistance of carbon and low-alloy steels. Under certain loading and environmental conditions, fatigue lives of test specimens may be shorter than those in air by a factor of H"0. The crack initiation and crack growth characteristics of carbon and low-alloy steels in LWR environments are presented. Decreases in fatigue life of these steels in high-dissolved-oxygen water are caused primarily by the effect of environment on growth of short cracks

Download or read book Corrosion Resistance of Steels Nickel Alloys and Zinc in Aqueous Media written by Michael Schütze and published by John Wiley & Sons. This book was released on 2016-01-05 with total page 418 pages. Available in PDF, EPUB and Kindle. Book excerpt: This handbook is derived from the online reference "Corrosion Handbook", bringing together the relevant information about corrosion protection and prevention for steels, one of the most widely used materials. It provides comprehensive information, including tabulated data and references, on the corrosion properties of the following materials: Unalloyed steels and cast steel, unalloyed cast iron, high-alloy cast iron, high-silicon cast iron, structural steels with up to 12% chromium, ferritic chromium steels with more than 12% chromium, ferritic-austenitic steels with more than 12% chromium, high-alloy multiphase steels, ferritic/perlitic-martensitic steels, ferritic-austenitic steels/duplex steels, austenitic chromium-nickel steels, austenitic chromium-nickel-molybdenum steels, austenitic chromium-nickel steels with special alloying additions, special iron-based alloys, and zinc. The following corrosive media are considered: Seawater, brackish water, industrial waste water, municipal waste water, drinking water, high-purity water.

Download or read book Initiation of Environmentally assisted Cracking in Low alloy Steels written by and published by . This book was released on 1996 with total page 22 pages. Available in PDF, EPUB and Kindle. Book excerpt: Environmentally-Assisted Cracking (EAC) in low alloy steels is activated by a critical level of sulfide ions at the crack tip, which is produced from dissolution of sulfide inclusions (MnS, FeS, etc.) in the steel following exposure by a growing crack. EAC of concern herein is the increase of fatigue crack growth rate of up to 40 to 100 times the rate in air that occurs at 240--300 C in high temperature LWR or boiler water environments. The initiation of EAC is the onset of the higher fatigue crack growth rates in fully developed cracks already presumed to be present due to fatigue, stress corrosion cracking, or induced by fabrication. Initiation of EAC is induced by a change in loading parameters causing the fatigue crack growth rate to increase from a small multiple (2--4) to 40--100 times the air rate. A steady state theory developed by Combrade, suggests that EAC will initiate only above a critical crack velocity and cease below this same velocity. However, more recent tests show that EAC can persist down to much lower velocities (100 times lower) in low oxygen water at slightly lower temperatures. A special set of experiments on high sulfur plate material demonstrate that EAC will not initiate from surface cracks with low sulfide inventories at low crack tip velocities. Transient diffusion calculations show that a finite crack extension at a high crack tip velocity is necessary to initiate EAC, providing a possible explanation for the lack of high crack growth observations reported in low alloy steels in structural applications involving low oxygen environments.

Download or read book Proceedings of the 15th International Conference on Environmental Degradation of Materials in Nuclear Power Systems Water Reactors written by Gabriell Ilevbare and published by Springer. This book was released on 2017-07-17 with total page 2354 pages. Available in PDF, EPUB and Kindle. Book excerpt: This 15th Edition of the International Conference on Materials Degradation in Light Water Reactors focuses on subject areas critical to the safe and efficient running of nuclear reactor systems through the exchange and discussion of reseach results as well as field operating and management experience.

Download or read book Comprehensive Nuclear Materials written by and published by Elsevier. This book was released on 2020-07-22 with total page 4871 pages. Available in PDF, EPUB and Kindle. Book excerpt: Materials in a nuclear environment are exposed to extreme conditions of radiation, temperature and/or corrosion, and in many cases the combination of these makes the material behavior very different from conventional materials. This is evident for the four major technological challenges the nuclear technology domain is facing currently: (i) long-term operation of existing Generation II nuclear power plants, (ii) the design of the next generation reactors (Generation IV), (iii) the construction of the ITER fusion reactor in Cadarache (France), (iv) and the intermediate and final disposal of nuclear waste. In order to address these challenges, engineers and designers need to know the properties of a wide variety of materials under these conditions and to understand the underlying processes affecting changes in their behavior, in order to assess their performance and to determine the limits of operation. Comprehensive Nuclear Materials, Second Edition, Seven Volume Set provides broad ranging, validated summaries of all the major topics in the field of nuclear material research for fission as well as fusion reactor systems. Attention is given to the fundamental scientific aspects of nuclear materials: fuel and structural materials for fission reactors, waste materials, and materials for fusion reactors. The articles are written at a level that allows undergraduate students to understand the material, while providing active researchers with a ready reference resource of information. Most of the chapters from the first Edition have been revised and updated and a significant number of new topics are covered in completely new material. During the ten years between the two editions, the challenge for applications of nuclear materials has been significantly impacted by world events, public awareness, and technological innovation. Materials play a key role as enablers of new technologies, and we trust that this new edition of Comprehensive Nuclear Materials has captured the key recent developments. Critically reviews the major classes and functions of materials, supporting the selection, assessment, validation and engineering of materials in extreme nuclear environments Comprehensive resource for up-to-date and authoritative information which is not always available elsewhere, even in journals Provides an in-depth treatment of materials modeling and simulation, with a specific focus on nuclear issues Serves as an excellent entry point for students and researchers new to the field

Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1994 with total page 836 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Nuclear Corrosion written by Stefan Ritter and published by Woodhead Publishing. This book was released on 2020-08-14 with total page 497 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nuclear Corrosion: Research, Progress and Challenges, part of the “Green Book series of the EFC, builds upon the foundations of the very first book published in this series in 1989 (“Number 1 - Corrosion in the Nuclear Industry ). This newest volume provides an overview on state-of-the-art research in some of the most important areas of nuclear corrosion. Chapters covered include aging phenomena in light water reactors, reprocessing plants, nuclear waste disposal, and supercritical water and liquid metal systems. This book will be a vital resource for both researchers and engineers working within the nuclear field in both academic and industrial environments. Discusses industry related aspects of materials in nuclear power generation and how these materials react with the environment Provides comprehensive coverage of the topic as written by noted experts in the field Includes coverage of nuclear waste corrosion

Download or read book Energy Research Abstracts written by and published by . This book was released on 1989 with total page 690 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Assessment Methodologies for Preventing Failure Service experience and environmental considerations written by Raj Mohan and published by . This book was released on 2000 with total page 214 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book The Shock and Vibration Digest written by and published by . This book was released on 1986 with total page 594 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book The Effect of Potential on the High temperature Fatigue Crack Growth Response of Low Alloy Steels written by and published by . This book was released on 1997 with total page 25 pages. Available in PDF, EPUB and Kindle. Book excerpt: Environmentally assisted cracking (EAC) in low alloy steels was found to be dependent on externally applied potential in low sulfur steels in high temperature water. EAC could be turned on when the specimen was polarized anodically above a critical potential. However, hydrogen (H) additions inhibited the ability of potential to affect EAC. The behavior was related to formation of H ions during H oxidation at the crack mouth. A mechanism based on formation of H sulfide at the crack tip and H ions at the crack mouth is presented to describe the process by which sulfides and H ions affect the critical sulfide concentration at the crack tip.

Download or read book Ninth International Symposium on Environmental Degradation of Materials in Nuclear Power Systems written by Steve Bruemmer and published by John Wiley & Sons. This book was released on 2013-10-18 with total page 1776 pages. Available in PDF, EPUB and Kindle. Book excerpt: This collection presents an exchange of ideas among scientists and engineers about the economic and safety concerns surrounding environmentally induced materials problems which lead to nuclear power plant outages. Scientists and engineers concerned with the environmental degradation processes (corrosion, mechanical, and radiation effects) present their latest results on such topics as life extension/relicensing and materials problems associated with spent fuel storage and radioactive waste disposal. This collection will be of interest to utility engineers, reactor vendor engineers, plant architect engineers, researchers concerned with materials degradation, and consultants involved in design, construction, and operation of water reactors.

Download or read book The Effect of Potential Upon the High temperature Fatigue Crack Growth Response of Low alloy Steels Part 1 written by and published by . This book was released on 1997 with total page 25 pages. Available in PDF, EPUB and Kindle. Book excerpt: Corrosion-fatigue crack propagation experiments were conducted on several low-alloy steels in elevated temperature aqueous environments, and experimental parameters included temperature, sulfur content of the steel, applied potential level, and dissolved hydrogen (and in one case, dissolved oxygen) concentration in the water. Specimen potentials were controlled potentiostatically, and the observation (or non-observation) of accelerated fatigue crack growth rates was a complex function of the above parameters. Electrochemical results and the postulated explanation for the complex behavior are given in Part II.