Download or read book Controlled Impingement of Drying Drops on Solid Surfaces written by Anil Thadani and published by . This book was released on 1970 with total page 234 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Controlled Impingement of Liquid Drops on Solid Spherical Surfaces written by Mounir Soliman Neamatalla and published by . This book was released on 1971 with total page 106 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Particle laden Drop Impingement on a Solid Surface written by Hyunyoung Ok and published by . This book was released on 2005 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: An experimental study on impaction of a single drop on solid surfaces was conducted to show the effects of particles on the impact process. The parameters were: volume fraction of particles (0 to 0.3), particle size (0.47 to 250 micron), and ratio of particle size to drop size (0.00017 to 0.074). The effect of particle volume fraction on the spreading process depended on impact speed and substrate. At low impact speed, particles had little effect on the spreading except for surfaces where the equilibrium contact angle was low. For high impact speed, the influence of particles on spreading can be described by the effective viscosity. The effect of particle size on the spreading process also depended on impact speed and substrate. At low impact speed, the drop did not have enough kinetic energy to overcome the energy barrier associated with the large particles. For particle-laden liquids, retraction was affected by particle parameters. When pure liquid drops retracted from the maximum spreading ratio, the retraction appeared to be symmetric around the point of impaction while retraction of the particle-laden drop was sometimes asymmetric. Rebounding on the Teflon film depended on impact speed, particle volume fraction, and particle size. The impact speed must reach a critical value for rebounding to occur. Bouncing results suggested that the probability of bouncing decreased as viscosity increased, impact speed increased, and surface tension decreased. The non-wetting behavior and bouncing probably involved an air layer between the surface and the drop. When a low-velocity liquid drop impacts on a surface, ejection of a secondary drop from the top of the impacting drop was sometimes observed. When Renardy et al.'s (2003) criterion for the range of velocities for existence of a capillary wave was applied to for a 3.2-mm water drop; the range was between 0.2 to 1.5 m/s. However, drop ejection was observed at lower impact speed. When apparent viscosity of the particle-laden liquid obtained from Krieger's equation (1972) was used in the pure liquid models for predicting the maximum spreading ratio, good agreement between model predictions and experimental results was obtained when Park et al's model (2003) was used.
Download or read book Drop Impingement and Interaction with a Solid Surface written by Heungsup Park and published by . This book was released on 2003 with total page 324 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Drops and Bubbles in Contact with Solid Surfaces written by Michele Ferrari and published by CRC Press. This book was released on 2016-04-19 with total page 344 pages. Available in PDF, EPUB and Kindle. Book excerpt: The third volume in a series dedicated to colloids and interfaces, Drops and Bubbles in Contact with Solid Surfaces presents an up-to-date overview of the fundamentals and applications of drops and bubbles and their interaction with solid surfaces. The chapters cover the theoretical and experimental aspects of wetting and wettability, liquid-solid
Download or read book The Effect of Relative Humidity on the Collision Behavior of Water Drops in the Air written by Lee Edward Baker and published by . This book was released on 1972 with total page 438 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Drying of Complex Fluid Drops written by David Brutin and published by Royal Society of Chemistry. This book was released on 2022-06-01 with total page 244 pages. Available in PDF, EPUB and Kindle. Book excerpt: Coffee rings, paint drying, blood splatter are all examples of complex fluids drying. Understanding the phenomena of complex fluid drops with respect to drying is important for technology and a lot of research in academia and industry is poured into this topic. This book addresses this industrially important area and provides a thorough grounding to the field. Addressing the fundamental underpinnings of wetting, spreading and drying, the book then takes the reader through key applications grouped into themes, including colloidal droplets (used in printing) and biological (e.g. bloodstain analysis for forensics). With a section on modelling and simulation to balance experiment with computational tools, this book will appeal to anyone working in complex fluids across classical fluid mechanics, soft matter, and chemical, biological and mechanical engineering
Download or read book Master s Theses and Doctoral Dissertations in the Pure and Applied Sciences written by and published by . This book was released on 1971 with total page 186 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Masters Theses and Doctoral Dissertations in the Pure and Applied Sciences Accepted by Colleges and Universities of the United States written by and published by . This book was released on 1971 with total page 544 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Mechanical Engineering And Control Systems Proceedings Of 2015 International Conference Mecs2015 written by Xiaolong Li and published by World Scientific. This book was released on 2016-01-15 with total page 543 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book consists of 113 selected papers presented at the 2015 International Conference on Mechanical Engineering and Control Systems (MECS2015), which was held in Wuhan, China during January 23-25, 2015. All accepted papers have been subjected to strict peer review by two to four expert referees, and selected based on originality, ability to test ideas and contribution to knowledge.MECS2015 focuses on eight main areas, namely, Mechanical Engineering, Automation, Computer Networks, Signal Processing, Pattern Recognition and Artificial Intelligence, Electrical Engineering, Material Engineering, and System Design. The conference provided an opportunity for researchers to exchange ideas and application experiences, and to establish business or research relations, finding global partners for future collaborations. The conference program was extremely rich, profound and featured high-impact presentations of selected papers and additional late-breaking contributions.
Download or read book Control and Safety Analysis of Intensified Chemical Processes written by Gade Pandu Rangaiah and published by John Wiley & Sons. This book was released on 2024-06-10 with total page 389 pages. Available in PDF, EPUB and Kindle. Book excerpt: Resource on the design and safety analysis of intensified chemical processes, ranging from general methods to specific applications Control and Safety Analysis of Intensified Chemical Processes covers the basic principles of and recent developments in control and safety analysis of intensified chemical processes, ranging from dynamic simulations and safety analysis to the design and control of important processes. The text discusses general methods and tools such as dynamic simulation and safety analysis as well as design and analysis of important applications in order to provide scientists and engineers with an understanding of the design and safety considerations involved in intensified chemical processes. Sample topics covered in Control and Safety Analysis of Intensified Chemical Processes include: Simulation and optimization methods, common programs and simulators for simulation and optimization, and interfacing of simulators and optimizers Programs/simulators for dynamic simulation and control, tuning of controllers, and popular criteria for control assessment Control of a distillation column with dual steam and hot-oil reboilers, and an energy intensified side-stream extractive distillation for binary azeotropic separation Dynamics and control of middle vessel batch distillation with vapor recompression and development of a control structure of intensified biobutanol production A comprehensive resource on the subject, Control and Safety Analysis of Intensified Chemical Processes is a highly valuable reference for researchers, students and practitioners interested in process intensification and their applications. The text can be adopted by instructors for use in advanced courses on process control and safety.
Download or read book Annual Report written by University of Wisconsin--Madison. Engineering Experiment Station and published by . This book was released on 1969 with total page 124 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Handbook of Industrial Drying written by Arun S. Mujumdar and published by CRC Press. This book was released on 2014-07-11 with total page 1334 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Fourth Edition book includes 12 new chapters covering computational fluid dynamic simulation; solar, impingement, and pulse combustion drying; drying of fruits, vegetables, sugar, biomass, and coal; physicochemical aspects of sludge drying; and life-cycle assessment of drying systems. Addressing commonly encountered dryers as well as innovative dryers with future potential, the fully revised text not only delivers a comprehensive treatment of the current state of the art, but also serves as a consultative reference for streamlining industrial drying operations to increase energy efficiency and cost-effectiveness.
Download or read book Tribology in Industries written by Srivastava, Sushil Kumar and published by S. Chand Publishing. This book was released on 2004-08 with total page 212 pages. Available in PDF, EPUB and Kindle. Book excerpt: A Textbook-cum-reference book for Undergraduate, Graduate and Postgraduate students of Mechanical, Electrical, Maintenance and Production Engineering disciplines. This book would also be of immensehelp to various practising engineers, technologists, managers and supervisiors engaged in the maintenance, operation and upkeep of the different machines, equipments, systems and plants of various industries.
Download or read book High Value Manufacturing Advanced Research in Virtual and Rapid Prototyping written by Maria K. Todd and published by CRC Press. This book was released on 2013-09-16 with total page 650 pages. Available in PDF, EPUB and Kindle. Book excerpt: High Value Manufacturing is the result of the 6th International Conference on Advanced Research in Virtual and Rapid Prototyping, held in Leiria, Portugal, October 2013. It contains current contributions to the field of virtual and rapid prototyping (V&RP) and is also focused on promoting better links between industry and academia. This volume
Download or read book Annual Report Engineering Experiment Station University of Wisconsin Madison written by University of Wisconsin--Madison. Engineering Experiment Station and published by . This book was released on 1969 with total page 324 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Kirk Othmer Concise Encyclopedia of Chemical Technology 2 Volume Set written by Kirk-Othmer and published by John Wiley & Sons. This book was released on 2007-07-16 with total page 2762 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is an easily-accessible two-volume encyclopedia summarizing all the articles in the main volumes Kirk-Othmer Encyclopedia of Chemical Technology, Fifth Edition organized alphabetically. Written by prominent scholars from industry, academia, and research institutions, the Encyclopedia presents a wide scope of articles on chemical substances, properties, manufacturing, and uses; on industrial processes, unit operations in chemical engineering; and on fundamentals and scientific subjects related to the field.
