Download or read book Constitutive Equations for Engineering Materials written by Wai-Fah Chen and published by Elsevier. This book was released on 2013-10-22 with total page 595 pages. Available in PDF, EPUB and Kindle. Book excerpt: Constitutive Equations for Engineering Materials, Volume 1: Elasticity and Modeling, Revised Edition focuses on theories on elasticity and plasticity of engineering materials. The book first discusses vectors and tensors. Coordinate systems, vector algebra, scalar products, vector products, transformation of coordinates, indicial notation and summation convention, and triple products are then discussed. The text also ponders on analysis of stress and strain and presents numerical analysis. The book then discusses elastic stress-strain relations. Basic assumptions; need for elastic models; isotropic linear stress-strain relations; principle of virtual work; strain energy and complementary energy density in elastic solids; and incremental relations grounded on secant moduli are described. The text also explains linear elasticity and failure criteria for concrete and non-linear elasticity and hypoelastic models for concrete. The selection further tackles soil elasticity and failure criteria. Mechanical behavior of soils; failure criteria of soils; and incremental stress-strain models based on modification of the isotropic linear elastic formulation are considered. The text is a good source of data for readers interested in studying the elasticity and plasticity of engineering materials.
Download or read book Constitutive Equations for Engineering Materials written by Wai-Fah Chen and published by Elsevier Science Limited. This book was released on 1994 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Hardbound. Volume 2 extends the elasticity-based stress-strain models to the plastic range and develops plasticity-based models for engineering applications and is divided into four parts. Parts one and two contain a sufficient comprehensive treatment of the classical theory of plasticity and its applications to metal structures. Parts three and four present a state-of-the-art coverage of concrete plasticity and soil plasticity.
Download or read book Constitutive Equations for Engineering Materials written by W. F. (Wai-Fah) Chen and published by . This book was released on 1982 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Constitutive Equations for Engineering Materials written by and published by . This book was released on 1994 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Constitutive equations for engineering materials 2 Plasticity and modeling written by and published by . This book was released on 1994 with total page 547 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Constitutive Equations for Engineering Materials written by Wai-Fah Chen and published by . This book was released on 1980 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Cyclic Plasticity of Engineering Materials written by Guozheng Kang and published by John Wiley & Sons. This book was released on 2017-03-10 with total page 552 pages. Available in PDF, EPUB and Kindle. Book excerpt: New contributions to the cyclic plasticity of engineering materials Written by leading experts in the field, this book provides an authoritative and comprehensive introduction to cyclic plasticity of metals, polymers, composites and shape memory alloys. Each chapter is devoted to fundamentals of cyclic plasticity or to one of the major classes of materials, thereby providing a wide coverage of the field. The book deals with experimental observations on metals, composites, polymers and shape memory alloys, and the corresponding cyclic plasticity models for metals, polymers, particle reinforced metal matrix composites and shape memory alloys. Also, the thermo-mechanical coupled cyclic plasticity models are discussed for metals and shape memory alloys. Key features: Provides a comprehensive introduction to cyclic plasticity Presents Macroscopic and microscopic observations on the ratchetting of different materials Establishes cyclic plasticity constitutive models for different materials. Analysis of cyclic plasticity in engineering structures. This book is an important reference for students, practicing engineers and researchers who study cyclic plasticity in the areas of mechanical, civil, nuclear, and aerospace engineering as well as materials science.
Download or read book Generalized Plasticity written by Mao-Hong Yu and published by Springer Science & Business Media. This book was released on 2006-05-20 with total page 462 pages. Available in PDF, EPUB and Kindle. Book excerpt: Generalized Plasticity deals with the plasticity of materials and structures. It is an expansion of the "Unified Strength Theory to Plasticity Theory", leading to a unified treatment of metal plasticity and plasticity of geomaterials, generally. It includes the metal plasticity for Tresca materials, Huber-von-Mises materials and twin-shear materials and the geomaterial plasticity for Mohr-Coulomb materials, generalized twin-shear materials and the Unified Strength Theory.
Download or read book Mechanical Constitutive Models for Engineering Materials written by Behzad Rohani and published by . This book was released on 1977 with total page 190 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Unified Constitutive Equations for Creep and Plasticity written by A.K. Miller and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 351 pages. Available in PDF, EPUB and Kindle. Book excerpt: Constitutive equations refer to 'the equations that constitute the material response' at any point within an object. They are one of the ingredients necessary to predict the deformation and fracture response of solid bodies (among other ingredients such as the equations of equilibrium and compatibility and mathematical descriptions of the configuration and loading history). These ingredients are generally combined together in complicated computer programs, such as finite element analyses, which serve to both codify the pertinent knowledge and to provide convenient tools for making predictions of peak stresses, plastic strain ranges, crack growth rates, and other quantities of interest. Such predictions fall largely into two classes: structural analysis and manufacturing analysis. In the first category, the usual purpose is life prediction, for assessment of safety, reliability, durability, and/or operational strategies. Some high-technology systems limited by mechanical behavior, and therefore requiring accurate life assess ments, include rocket engines (the space-shuttle main engine being a prominent example), piping and pressure vessels in nuclear and non-nuclear power plants (for example, heat exchanger tubes in solar central receivers and reformer tubes in high-temperature gas-cooled reactors used for process heat applications), and the ubiquitous example of the jet engine turbine blade. In structural analysis, one is sometimes concerned with predicting distortion per se, but more often, one is concerned with predicting fracture; in these cases the informa tion about deformation is an intermediate result en route to the final goal of a life prediction.
Download or read book Unified Plasticity for Engineering Applications written by Sol R. Bodner and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 126 pages. Available in PDF, EPUB and Kindle. Book excerpt: Considerably simplified models of macroscopic material behavior, such as the idealization for metals of elastic-time independent plastic response with a yield (onset) criterion, have served the engineering profession well for many years. They are still basic to the design and analysis of most structural applications. In the need to use materials more effectively, there are circumstances where those traditional models are not adequate, and constitutive laws that are more physically realistic have to be employed. This is especially relevant to conditions where the inherent time dependence of inelastic deformations, referred to as "viscoplasticity", is pronounced such as at elevated temperatures and for high strain rates. Unified theories of elastic-viscoplastic material behavior, which are primarily applicable for metals and metallic alloys, combine all aspects of inelastic response into a set of time dependent equations with a single inelastic strain rate variable. For such theories, creep under constant stress, stress relaxation under constant strain, and stress-strain relations at constant rates are each special cases of a general formulation. Those equations mayor may not include a yield criterion, but models which do not separate a fully elastic region from the overall response could be considered "unified" in a more general sense. The theories have reached a level of development and maturity where they are being used in a number of sophisticated engineering applications. However, they have not yet become a standard method of material representation for general engineering practice.
Download or read book Plasticity in Reinforced Concrete written by Wai-Fah Chen and published by J. Ross Publishing. This book was released on 2007 with total page 500 pages. Available in PDF, EPUB and Kindle. Book excerpt: J. Ross Publishing Classics are world-renowned texts and monographs written bt preeminent scholars. These books are available to students, researchers, professionals, and libararies.
Download or read book Constitutive Modeling of Engineering Materials written by Vladimir Buljak and published by Academic Press. This book was released on 2021-02-18 with total page 330 pages. Available in PDF, EPUB and Kindle. Book excerpt: Constitutive Modeling of Engineering Materials provides an extensive theoretical overview of elastic, plastic, damage, and fracture models, giving readers the foundational knowledge needed to successfully apply them to and solve common engineering material problems. Particular attention is given to inverse analysis, parameter identification, and the numerical implementation of models with the finite element method. Application in practice is discussed in detail, showing examples of working computer programs for simple constitutive behaviors. Examples explore the important components of material modeling which form the building blocks of any complex constitutive behavior. Addresses complex behaviors in a wide range of materials, from polymers, to metals and shape memory alloys Covers constitutive models with both small and large deformations Provides detailed examples of computer implementations for material models
Download or read book Modelling of Engineering Materials written by C. Lakshmana Rao and published by John Wiley & Sons. This book was released on 2014-07-02 with total page 202 pages. Available in PDF, EPUB and Kindle. Book excerpt: Modelling of Engineering Materials presents the background that is necessary to understand the mathematical models that govern the mechanical response of engineering materials. The book provides the basics of continuum mechanics and helps the reader to use them to understand the development of nonlinear material response of solids and fluids used in engineering applications. A brief review of simplistic and linear models used to characterize the mechanical response of materials is presented. This is followed by a description of models that characterize the nonlinear response of solids and fluids from first principles. Emphasis is given to popular models that characterize the nonlinear response of materials. The book also presents case studies of materials, where a comprehensive discussion of material characterization, experimental techniques and constitutive model development, is presented. Common principles that govern material response of both solids and fluids within a unified framework are outlined. Mechanical response in the presence of non-mechanical fields such as thermal and electrical fields applied to special materials such as shape memory materials and piezoelectric materials is also explained within the same framework.
Download or read book Plasticity Limit Analysis Stability And Structural Design An Academic Life Journey From Theory To Practice written by Wai-fah Chen and published by World Scientific. This book was released on 2021-01-22 with total page 612 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is a personal anthology of the author's utmost academic works and accomplishments with his former students and colleagues intended as an enduring record for the engineering community for many years to come.The author's forty-year professional career and academic life journey is first briefly sketched in Chapter 1 and more details are elaborated in three chapters that follow: Chapter 2: The first ten years at Lehigh — beginning to show; Chapter 3: Twenty=three years at Purdue — the highly productive years; and Chapter 4: seven years at UH — the pursuit of excellence. The author's specific academic contributions are documented in the following three chapters: Chapter 5: 23 academic bulletins are selected to highlight his 10 major research areas; Chapter 6: 23 Academic masterpiece books are listed along with their respective peer review comments; and Chapter 7: academic publications include journal articles, conference proceedings and symposiums, and lectures and keynotes. The book ends with the listing of all the author's 55 doctoral students' dissertation titles in Chapter 8.In 1975 at Lehigh, the author published a milestone treatise on Limit Analysis and Soil Plasticity. In 1982 at Purdue, he published another pioneering work on Plasticity in Reinforced Concrete.In September 1999, the author was recruited by UH to take the Deanship of the College of Engineering to accomplish the noble mission: to build the College to become one of the top 50 engineering schools by strengthening the faculty, improving the facilities, and increasing the enrollment. Over his seven years at UH, a lot of progress was made in all these three areas — the research program expanded, facilities improved, and enrollment increased.
Download or read book Constitutive Modelling for Engineering Materials with Applications written by American Society of Mechanical Engineers. Winter Meeting and published by . This book was released on 1988 with total page 122 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Developments in Geotechnical Engineering from Harvard to New Delhi 1936 1994 written by A.S. Balasubramaniam and published by CRC Press. This book was released on 2021-06-30 with total page 593 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book reviews the developments that have taken place in the field of geotechnical engineering since the first international conference on Soil Mechanics and Foundation Engineering was held in Harvard University in 1936 until the January 1994 conference in New Delhi, India.
