Download or read book Connections for Hydraulic Fluid Power and General Use Hose Fittings Hose Fittings with ISO 6149 Metric Stud Ends written by British Standards Institute Staff and published by . This book was released on 2007-08-31 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt: Hose connectors, Flexible pipes, Pipe connections, Hydraulic equipment, Hydraulic transmission systems, Stud couplings, Pipe couplings, Bend couplings, Unalloyed steels, Dimensions, Performance, Designations, Screwed fittings, Threads, Assembling
Download or read book Connections for Fluid Power and General UsePorts and Stud Ends with ISO 261 Threads and O Ring Sealing Part 1 Port with O Ring Seal in Truncated Housing written by Hydraulic Tube Fittings Committee and published by . This book was released on 2007 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This part of SAE J2244 specifies dimensions for fluid power metric ports for use with adjustable and nonadjustable stud ends shown in SAE J2244/2.Ports in accordance with this part of SAE J2244 may be used at working pressures up to 63 MPa for nonadjustable stud ends and 40 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc.For threaded ports and stud ends specified in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used for new designs in hydraulic fluid power applications. All parts of SAE J2244 are being cancelled. SAE J2244 was published to provide users and manufacturers access to metric port and stud end dimensions. ISO 6149 is more recognized in the industry as the preferred metric port and stud end standard, thus the SAE FCCTC SC1 committee has approved cancelling SAE J2244-1 and superseding it with ISO 6149-1.
Download or read book Connections for Fluid Power and General Use Ports and Stud Ends with ISO 261 Threads and O Ring Sealing Part 2 Heavy Duty S Series Stud Ends Dimensions Design Test Methods and Requirements written by Hydraulic Tube Fittings Committee and published by . This book was released on 2007 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This part of SAE J2244 specifies dimensions, performance requirements, and test procedures for metric adjustable and nonadjustable heavy-duty (S Series) stud ends and O-rings. Stud ends in accordance with this part of SAE J2244 may be used at working pressures up to 63 MPa for nonadjustable stud ends and 40 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc. For threaded ports and stud ends for use in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used for new designs in hydraulic fluid power applications. Conformance to the dimensional information in this standard does not guarantee rated performance. Each manufacturer shall perform testing according to the specification contained in this standard to ensure that components made to this standard comply with the performance ratings.All parts of SAE J2244 are being cancelled. J2244 was published to provide users and manufacturers access to metric port and stud end dimensions. ISO 6149 is more recognized in the industry as the preferred metric port and stud end standard, thus the SAE FCCTC SC 1 committee has approved cancelling SAE J2244-2 and superseding it with ISO 6149-2.
Download or read book Connections for Fluid Power and General Use Ports and Stud Ends with ISO 261 Threads and O Ring Sealing Part 4 Heavy Duty S Series External Hex Port Plugs Dimensions Design Test Methods and Requirements written by Hydraulic Tube Fittings Committee and published by . This book was released on 2007 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This part of SAE J2244 specifices dimensions, performance requirements, and test procedures for metric external hex O-rings port plugs. Port plugs in accordance with this part of SAE J2244 may be used at working pressures up to 63 MPa. The permissible working pressure depends upon materials, design, working conditions, applications, etc. For threaded ports and stud ends for use in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used in new designs in hydrualic fluid power applications. Conformance to the dimensional information in this document does not guarantee rated performance. Each manufacturer shall perform testing according to the specification contained in this document to ensure that components made to this document comply with the performance ratings.All parts of SAE J2244 are being cancelled. J2244 was published to provide users and manufacturers access to metric port and stud end dimensions. ISO 6149 is more recognized in the industry as the preferred metric port and stud end standard, thus the SAE FCCTC SC 1 committee has approved cancelling SAE J2244-4 and superseding it with ISO 6149-4.
Download or read book Connections for Fluid Power and General Use Ports and Stud Ends with ISO 261 Metric Threads and O Ring Sealing Part 3 Light Duty L Series Stud Ends Dimensions Design Test Methods and Requirements written by Hydraulic Tube Fittings Committee and published by . This book was released on 2007 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This part of SAE J2244 specifies dimensions, performancerequirements, and test procedures for metric adjustable andnonadjustable light-duty (L series) stud ends and O-rings.Stud ends in accordance with this part of SAE J2244 may be usedat working pressures up to 40 MPa for nonadjustable stud ends and31.5 MPa for adjustable stud ends. The permissible working pressuredepends upon materials, design, working conditions, applications,etc.For threaded ports and stud ends for use in new designs inhydraulic fluid power applications, only SAE J2244 shall be used.Threaded ports and stud ends in accordance with ISO 1179, ISO 9974,and SAE J1926 (ISO 11926) shall not be used in new designs inhydraulic fluid power applications.Conformance to the dimensional information in this SAE Standarddoes not guarantee rated performance. Each manufacturer shallperform testing according to the specification contained in thisdocument to ensure that components made to this document complywith the performance ratings.All parts of SAE J2244 are being cancelled. J2244 was published to provide users and manufacturers access to metric port and stud end dimensions. ISO 6149 is more recognized in the industry as the preferred metric port and stud end standard, thus the SAE FCCTC SC 1 committee has approved cancelling SAE J2244-3 and superseding it with ISO 6149-3.
Download or read book The Hydraulic Handbook written by Trevor M. Hunt and published by Elsevier. This book was released on 1996 with total page 792 pages. Available in PDF, EPUB and Kindle. Book excerpt: Hardbound. The first point of reference for design engineers, hydraulic technicians, chief engineers, plant engineers, and anyone concerned with the selection, installation, operation or maintenance of hydraulics equipment. The hydraulic industry has seen many changes over recent years and numerous new techniques, components and methods have been introduced. The ninth edition of the Hydraulic Handbook incorporates all these developments to provide a crucial reference manual for practical and technical guidance.
Download or read book Connections for General Use and Fluid PowerPorts and Stud Ends with ASME B1 1 Threads and O Ring SealingPart 3 Light Duty L Series Stud Ends written by Hydraulic Tube Fittings Committee and published by . This book was released on 2010 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This part of SAE J1926 specifies dimensions, performance requirements, and test procedures for adjustable and nonadjustable light-duty (L series) stud ends with ASME B1.1 threads for use in fluid power and general applications and the O-rings used with them.Stud ends in accordance with this part of SAE J1926 may be used at working pressures up to 35 MPa for nonadjustable and adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc.For threaded ports and stud end specified in new designs for hydraulic fluid power applications, only ISO 6149 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and ISO 11926 shall not be used for new design in hydraulic fluid power applications.Conformance to the dimensional Information does not guarantee rated performance. Each manufacturer shall perform testing according to the specification contained in this document to ensure that components made to this document comply with the performance rating.Appendices A of this document is informative.NOTE: This document specifies inch as well as metric hexes for the stud ends. Therefore, any product drawing specifying stud ends in accordance with this document must specify hex type, inch or metric, to assure getting intended hex.Stud ends or parts specified before January 1, 2010 using this standard, shall be supplied with inch hexes, unless otherwise specified. General revision for harmonizationwith SAE J514 and ISO 11926-3 and addition of sizes -40, -48 and -64 and converting the document to metric hex standard in accordance with FCCTC resolution on metric hex conversion. The resolution provides rationale for converting to metric hex and not using inch hex for new designs as follows: "In an effort to standardize within a global market and ensuring that companies can remain competitive in an international market, it is the intent to convert to metric hex sizes which will: -lead to one global standard -guide users to a preferred system -reduce complexity -eliminate duplication -reduce confusion"
Download or read book Connections for General Use and Fluid Power Ports and Stud Ends with ASME B1 1 Threads and O Ring Sealing Part 2 Heavy Duty S Series Stud Ends written by Hydraulic Tube Fittings Committee and published by . This book was released on 2023 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This part of SAE J1926 specifies dimensions, performance requirements, and test procedures for adjustable and nonadjustable heavy-duty (S series) stud ends with ASME B1.1 threads for use in fluid power and general applications.Stud ends in accordance with this part of SAE J1926 may be used at working pressures up to 63 MPa for nonadjustable stud ends and up to 41.3 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc.For threaded ports and stud ends specified in new designs for hydraulic fluid power applications, only ISO 6149 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and ISO 11926 shall not be used for new design in hydraulic fluid power applications. Conformance to the dimensional information does not guarantee rated performance. Each manufacturer shall perform testing according to the specification contained in this document to ensure that components made to this document comply with the performance rating.Appendices A and B of this document are informative. This document was revised in order to remove Table 5.
Download or read book Connections for General Use and Fluid PowerPorts and Stud Ends with ASME B1 1 Threads and O Ring SealingPart 2 Heavy Duty S Series Stud Ends written by Hydraulic Tube Fittings Committee and published by . This book was released on 2010 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This part of SAE J1926 specifies dimensions, performance requirements, and test procedures for adjustable and nonadjustable heavy-duty (S series) stud ends with ASME B1.1 threads for use in fluid power and general applications and the O-rings used with them that are currently not listed in SAE J515.Stud ends in accordance with this part of SAE J1926 may be used at working pressures up to 63 MPa for nonadjustable stud ends and up to 41.3 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc.For threaded ports and stud ends specified in new designs for hydraulic fluid power applications, only ISO 6149 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and ISO 11926 shall not be used for new design in hydraulic fluid power applications.NOTE: This document specifies inch as well as metric hexes for the stud ends. Therefore, any product drawing specifying stud ends in accordance with this document must specify hex type, inch or metric, to assure getting intended hex.Stud ends or parts specified before January 1, 2010 using this standard, shall be supplied with inch hexes, unless otherwise specified.Conformance to the dimensional information does not guarantee rated performance. Each manufacturer shall perform testing according to the specification contained in this document to ensure that components made to this document comply with the performance rating.Appendix A of this document is informative. General revision for harmonization with J1453-3 and ISO 11926-2, addition of sizes -32, -40 and-48 and converting the document to metric hex standard in accordance with FCCTC resolution on metric hex conversion. The resolution provides rationale for converting to metric hex and not using inch hex for new designs as follows: "In an effort to standardize within a global market and ensuring that companies can remain competitive in an international market, it is the intent to convert to metric hex sizes which will: -lead to one global standard -guide users to a preferred system -reduce complexity -eliminate duplication -reduce confusion"
Download or read book Connections for Hydraulic Fluid Power and General Use Hose Fittings Hose Fittings with ISO 8434 6 60 0D Cone Ends written by British Standards Institute Staff and published by . This book was released on 2009-12-31 with total page 24 pages. Available in PDF, EPUB and Kindle. Book excerpt: Hose connectors, Flexible pipes, Pipe connections, Hydraulic equipment, Hydraulic transmission systems, Pipe couplings, Unalloyed steels, Dimensions, Performance, Designations, Screwed fittings, Threads
Download or read book Connections for Hydraulic Fluid Power and General Use Ports and Stud Ends with ISO 261 Metric Threads and O Ring Sealing Dimensions Design Test Methods and Requirements for Light Duty L Series Stud Ends written by British Standards Institute Staff and published by . This book was released on 2006-03-31 with total page 22 pages. Available in PDF, EPUB and Kindle. Book excerpt: Hydraulic transmission systems, Pneumatic transmission systems, Stud couplings, Pipe couplings, Pipe fittings, Screwed fittings, Light-duty, Toroidal sealing rings, Dimensions, Performance, Service pressure, Low-carbon steels, Steels, Threads, Marking, Identification methods
Download or read book Connections for Hydraulic Fluid Power and General Use Ports and Stud Ends with ISO 261 Metric Threads and O Ring Sealing Dimensions Design Test Methods and Requirements for Heavy Duty S Series Stud Ends written by British Standards Institute Staff and published by . This book was released on 2006-03-31 with total page 22 pages. Available in PDF, EPUB and Kindle. Book excerpt: Hydraulic transmission systems, Pneumatic transmission systems, Stud couplings, Pipe couplings, Pipe fittings, Screwed fittings, Heavy-duty, Toroidal sealing rings, Sealing rings, Dimensions, Performance, Service pressure, Low-carbon steels, Steels, Threads, Marking, Identification methods, Designations
Download or read book Connections for Hydraulic Fluid Power and General Use Hose Fittings written by British Standards Institution and published by . This book was released on 2017 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Connections for Hydraulic Fluid Power and General Use Ports and Stud Ends with ISO 261 Metric Threads and O Ring Sealing Ports with Truncated Housing for O Ring Seal written by British Standards Institute Staff and published by . This book was released on 2006-03-31 with total page 16 pages. Available in PDF, EPUB and Kindle. Book excerpt: Hydraulic transmission systems, Pneumatic transmission systems, Orifices, Stud couplings, Holes, Pipe couplings, Pipe fittings, Screwed fittings, Threads, Toroidal sealing rings, Dimensions, Identification methods, Service pressure, Marking
Download or read book Connections for General Use and Fluid Power Ports and Stud Ends with ASME B1 1 Threads and O Ring Sealing Part 3 Light Duty L Series Stud Ends written by Hydraulic Tube Fittings Committee and published by . This book was released on 2016 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This part of SAE J1926 specifies dimensions, performance requirements, and test procedures for adjustable and nonadjustable light-duty (L series) stud ends with ASME B1.1 threads for use in fluid power and general applications and the O-rings used with them.Stud ends in accordance with this part of SAE J1926 may be used at working pressures up to 35 MPa for nonadjustable and adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc.For threaded ports and stud end specified in new designs for hydraulic fluid power applications, only ISO 6149 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and ISO 11926 shall not be used for new design in hydraulic fluid power applications.Conformance to the dimensional information does not guarantee rated performance. Each manufacturer shall perform testing according to the specification contained in this document to ensure that components made to this document comply with the performance rating.Appendices A and B of this document are informative. This document was revised in order to move the optional inch hex sizes and dimensions to Appendix B.In an effort to standardize within a global market and ensuring that companies can remain competitive in an international market, it is the intent to convert to metric hex sizes which will: -lead to one global system -guide users to preferred system -reduce complexity -eliminate duplicationsThe optional inch hexes now contain the note "NOT TO BE USED FOR NEW DESIGN" in accordance with the Metric Hex Resolution approved during the March 2008 FCCTC meeting.
Download or read book Connections for Hydraulic Fluid Power and General Use Hose Fittings Hose Fittings with ISO 8434 1 and ISO 8434 4 24 0d Cone Connector Ends with O Rings written by British Standards Institute Staff and published by . This book was released on 2003-07-16 with total page 22 pages. Available in PDF, EPUB and Kindle. Book excerpt: Hose connectors, Flexible pipes, Pipe connections, Hydraulic equipment, Hydraulic transmission systems, Fluid equipment, Steels, Dimensions, Design, Toroidal sealing rings, Pipe fittings
Download or read book Connections for hydraulic fluid power and general use hose fittings Part 2 Hose fittings with ISO 8434 1 24 cone connector ends with O rings ISO 12151 2 2022 written by and published by . This book was released on 2023 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
