Download or read book Computational Investigation of a Boundary layer Ingestion Propulsion System for the Common Research Model written by Brennan Blumenthal and published by . This book was released on 2016 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: This thesis will examine potential propulsive and aerodynamic benefits of integrating a Boundary-layer Ingestion (BLI) propulsion system with a typical commercial aircraft using the Common Research Model geometry and the NASA Tetrahedral Unstructured Software System (TetrUSS). The Numerical Propulsion System Simulation (NPSS) environment will be used to generate engine conditions for CFD analysis. Improvements to the BLI geometry will be made using the Constrained Direct Iterative Surface Curvature (CDISC) design method. Previous studies have shown reductions of up to 25% in terms of propulsive power required for cruise for other axisymmetric geometries using the BLI concept. An analysis of engine power requirements, drag, and lift coefficients using the baseline and BLI geometries coupled with the NPSS model are shown. Potential benefits of the BLI system relating to cruise propulsive power are quantified using a power balance method and a comparison to the baseline case is made. Iterations of the BLI geometric design are shown and any improvements between subsequent BLI designs presented. Simulations are conducted for a cruise flight condition of Mach 0.85 at an altitude of 38,500 feet and an angle of attack of 2° for all geometries. A comparison between available wind tunnel data, previous computational results, and the original CRM model is presented for model verification purposes along with full results for BLI power savings. Results indicate a 14.3% reduction in engine power requirements at cruise for the BLI configuration over the baseline geometry. Minor shaping of the aft portion of the fuselage using CDISC has been shown to increase the benefit from boundary-layer ingestion further, resulting in a 15.6% reduction in power requirements for cruise as well as a drag reduction of eighteen counts over the baseline geometry.
Download or read book Green Approaches in Sustainable Aviation written by T. Hikmet Karakoc and published by Springer Nature. This book was released on 2023-11-11 with total page 188 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sustainable aviation is a long-term strategy to provide innovative solutions to the industry’s environmental challenges. The International Symposium on Sustainable Aviation is a multi-disciplinary symposium that presents research on current sustainability-based issues and future trends in aviation from an economic, social, and environmental perspective. The conference provides a platform offering insights on a broad range of current issues in aviation, such as aviation and environment, commercial air transport, regulations and policy, sustainable aerospace vehicles and technologies, and environmental modeling and measurements. The ISSA symposium allows researchers, scientists, engineers, practitioners, policymakers, and students to exchange information, present new technologies and developments, and discuss future direction, strategies, and priorities in sustainable aviation topics.
Download or read book Commercial Aircraft Propulsion and Energy Systems Research written by National Academies of Sciences, Engineering, and Medicine and published by National Academies Press. This book was released on 2016-08-09 with total page 123 pages. Available in PDF, EPUB and Kindle. Book excerpt: The primary human activities that release carbon dioxide (CO2) into the atmosphere are the combustion of fossil fuels (coal, natural gas, and oil) to generate electricity, the provision of energy for transportation, and as a consequence of some industrial processes. Although aviation CO2 emissions only make up approximately 2.0 to 2.5 percent of total global annual CO2 emissions, research to reduce CO2 emissions is urgent because (1) such reductions may be legislated even as commercial air travel grows, (2) because it takes new technology a long time to propagate into and through the aviation fleet, and (3) because of the ongoing impact of global CO2 emissions. Commercial Aircraft Propulsion and Energy Systems Research develops a national research agenda for reducing CO2 emissions from commercial aviation. This report focuses on propulsion and energy technologies for reducing carbon emissions from large, commercial aircraftâ€" single-aisle and twin-aisle aircraft that carry 100 or more passengersâ€"because such aircraft account for more than 90 percent of global emissions from commercial aircraft. Moreover, while smaller aircraft also emit CO2, they make only a minor contribution to global emissions, and many technologies that reduce CO2 emissions for large aircraft also apply to smaller aircraft. As commercial aviation continues to grow in terms of revenue-passenger miles and cargo ton miles, CO2 emissions are expected to increase. To reduce the contribution of aviation to climate change, it is essential to improve the effectiveness of ongoing efforts to reduce emissions and initiate research into new approaches.
Download or read book Introduction to the Theory of Flow Machines written by Albert Betz and published by Elsevier. This book was released on 2014-05-16 with total page 300 pages. Available in PDF, EPUB and Kindle. Book excerpt: Introduction to the Theory of Flow Machines details the fundamental processes and the relations that have a significant influence in the operating mechanism of flow machines. The book first covers the general consideration in flow machines, such as pressure, stress, and cavitation. In the second chapter, the text deals with ducts; this chapter discusses the general remarks, types of flow, and mixing process. Next, the book tackles the types of cascades, along with its concerns. The closing chapter covers the flow machine and its components, such as turbine, wheels, engines, and propellers. The text will be of great use to mechanical engineers and technicians.
Download or read book Aerial Robots written by Omar D Lopez Mejia and published by BoD – Books on Demand. This book was released on 2017-09-06 with total page 196 pages. Available in PDF, EPUB and Kindle. Book excerpt: Few years ago, the topic of aerial robots was exclusively related to the robotics community, so a great number of books about the dynamics and control of aerial robots and UAVs have been written. As the control technology for UAVs advances, the great interaction that exists between other systems and elements that are as important as control such as aerodynamics, energy efficiency, acoustics, structural integrity, and applications, among others has become evident. Aerial Robots - Aerodynamics, Control, and Applications is an attempt to bring some of these topics related to UAVs together in just one book and to look at a selection of the most relevant problems of UAVs in a broader engineering perspective.
Download or read book Introduction to Aircraft Flight Mechanics written by Thomas R. Yechout and published by AIAA. This book was released on 2003 with total page 666 pages. Available in PDF, EPUB and Kindle. Book excerpt: Based on a 15-year successful approach to teaching aircraft flight mechanics at the US Air Force Academy, this text explains the concepts and derivations of equations for aircraft flight mechanics. It covers aircraft performance, static stability, aircraft dynamics stability and feedback control.
Download or read book Fundamentals of Electric Propulsion written by Dan M. Goebel and published by John Wiley & Sons. This book was released on 2008-12-22 with total page 528 pages. Available in PDF, EPUB and Kindle. Book excerpt: Throughout most of the twentieth century, electric propulsion was considered the technology of the future. Now, the future has arrived. This important new book explains the fundamentals of electric propulsion for spacecraft and describes in detail the physics and characteristics of the two major electric thrusters in use today, ion and Hall thrusters. The authors provide an introduction to plasma physics in order to allow readers to understand the models and derivations used in determining electric thruster performance. They then go on to present detailed explanations of: Thruster principles Ion thruster plasma generators and accelerator grids Hollow cathodes Hall thrusters Ion and Hall thruster plumes Flight ion and Hall thrusters Based largely on research and development performed at the Jet Propulsion Laboratory (JPL) and complemented with scores of tables, figures, homework problems, and references, Fundamentals of Electric Propulsion: Ion and Hall Thrusters is an indispensable textbook for advanced undergraduate and graduate students who are preparing to enter the aerospace industry. It also serves as an equally valuable resource for professional engineers already at work in the field.
Download or read book Propulsion and Power written by Joachim Kurzke and published by Springer. This book was released on 2018-05-28 with total page 766 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book is written for engineers and students who wish to address the preliminary design of gas turbine engines, as well as the associated performance calculations, in a practical manner. A basic knowledge of thermodynamics and turbomachinery is a prerequisite for understanding the concepts and ideas described. The book is also intended for teachers as a source of information for lecture materials and exercises for their students. It is extensively illustrated with examples and data from real engine cycles, all of which can be reproduced with GasTurb (TM). It discusses the practical application of thermodynamic, aerodynamic and mechanical principles. The authors describe the theoretical background of the simulation elements and the relevant correlations through which they are applied, however they refrain from detailed scientific derivations.
Download or read book Distributed Propulsion Technology written by Amir S. Gohardani and published by Nova Science Publishers. This book was released on 2014 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Distributed propulsion technology is one of the revolutionary candidates for future aircraft propulsion. In this book, which serves as the very first reference book on distributed propulsion technology, the potential role of distributed propulsion technology in future aviation is investigated. Following a historical journey that revisits distributed propulsion technology in unmanned air vehicles, commercial aircrafts, and military aircrafts, features of this specific technology are highlighted in synergy with an electric aircraft concept and a first-of-its-kind comparison between commercial and military aircrafts employing distributed propulsion arrangements. In light of propulsionairframe integration and complementary technologies, such as boundary layer ingestion, thrust vectoring and circulation control, transpired opportunities and challenges are addressed in addition to a number of identified research directions proposed for future aircrafts. Moreover, a diverse set of distributed propulsion arrangements are considered. These include: small engines, gas-driven multi-fan architectures, turboelectric systems featuring superconductive and non-superconducting electrical machine technology, and electromagnetic fans. This book features contributions by the National Aeronautics and Space Administration (NASA) and the United States Air Force (USAF), and includes the first proposed official definition for distributed propulsion technology in subsonic fixed wing aircrafts.
Download or read book Shock Wave Boundary Layer Interactions written by Holger Babinsky and published by Cambridge University Press. This book was released on 2011-09-12 with total page 481 pages. Available in PDF, EPUB and Kindle. Book excerpt: Shock wave-boundary-layer interaction (SBLI) is a fundamental phenomenon in gas dynamics that is observed in many practical situations, ranging from transonic aircraft wings to hypersonic vehicles and engines. SBLIs have the potential to pose serious problems in a flowfield; hence they often prove to be a critical - or even design limiting - issue for many aerospace applications. This is the first book devoted solely to a comprehensive, state-of-the-art explanation of this phenomenon. It includes a description of the basic fluid mechanics of SBLIs plus contributions from leading international experts who share their insight into their physics and the impact they have in practical flow situations. This book is for practitioners and graduate students in aerodynamics who wish to familiarize themselves with all aspects of SBLI flows. It is a valuable resource for specialists because it compiles experimental, computational and theoretical knowledge in one place.
Download or read book Internal Flow written by E. M. Greitzer and published by Cambridge University Press. This book was released on 2007-02-26 with total page 739 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book describes the analysis and behaviour of internal flows encountered in propulsion systems, fluid machinery (compressors, turbines and pumps) and ducts (diffusers, nozzles and combustion chambers). The focus is on phenomena that are important in setting the performance of a broad range of fluid devices. The authors show that even for complex processes one can learn a great deal about the behaviour of such devices from a clear understanding and rigorous use of basic principles. Throughout the book they illustrate theoretical principles by reference to technological applications. The strong emphasis on fundamentals, however, means that the ideas presented can be applied beyond internal flow to other types of fluid motion. The book equips students and practising engineers with a range of new analytical tools. These tools offer enhanced interpretation and application of both experimental measurements and the computational procedures that characterize modern fluids engineering.
Download or read book Flight Vehicle Aerodynamics written by Mark Drela and published by MIT Press. This book was released on 2014-02-07 with total page 304 pages. Available in PDF, EPUB and Kindle. Book excerpt: An overview of the physics, concepts, theories, and models underlying the discipline of aerodynamics. This book offers a general overview of the physics, concepts, theories, and models underlying the discipline of aerodynamics. A particular focus is the technique of velocity field representation and modeling via source and vorticity fields and via their sheet, filament, or point-singularity idealizations. These models provide an intuitive feel for aerodynamic flow-field behavior and are the basis of aerodynamic force analysis, drag decomposition, flow interference estimation, and other important applications. The models are applied to both low speed and high speed flows. Viscous flows are also covered, with a focus on understanding boundary layer behavior and its influence on aerodynamic flows. The book covers some topics in depth while offering introductions and summaries of others. Computational methods are indispensable for the practicing aerodynamicist, and the book covers several computational methods in detail, with a focus on vortex lattice and panel methods. The goal is to improve understanding of the physical models that underlie such methods. The book also covers the aerodynamic models that describe the forces and moments on maneuvering aircraft, and provides a good introduction to the concepts and methods used in flight dynamics. It also offers an introduction to unsteady flows and to the subject of wind tunnel measurements. The book is based on the MIT graduate-level course “Flight Vehicle Aerodynamics” and has been developed for use not only in conventional classrooms but also in a massive open online course (or MOOC) offered on the pioneering MOOC platform edX. It will also serve as a valuable reference for professionals in the field. The text assumes that the reader is well versed in basic physics and vector calculus, has had some exposure to basic fluid dynamics and aerodynamics, and is somewhat familiar with aerodynamics and aeronautics terminology.
Download or read book Future Propulsion Systems and Energy Sources in Sustainable Aviation written by Saeed Farokhi and published by John Wiley & Sons. This book was released on 2020-01-21 with total page 444 pages. Available in PDF, EPUB and Kindle. Book excerpt: A comprehensive review of the science and engineering behind future propulsion systems and energy sources in sustainable aviation Future Propulsion Systems and Energy Sources in Sustainable Aviation is a comprehensive reference that offers a review of the science and engineering principles that underpin the concepts of propulsion systems and energy sources in sustainable air transportation. The author, a noted expert in the field, examines the impact of air transportation on the environment and reviews alternative jet fuels, hybrid-electric and nuclear propulsion and power. He also explores modern propulsion for transonic and supersonic-hypersonic aircraft and the impact of propulsion on aircraft design. Climate change is the main driver for the new technology development in sustainable air transportation. The book contains critical review of gas turbine propulsion and aircraft aerodynamics; followed by an insightful presentation of the aviation impact on environment. Future fuels and energy sources are introduced in a separate chapter. Promising technologies in propulsion and energy sources are identified leading to pathways to sustainable aviation. To facilitate the utility of the subject, the book is accompanied by a website that contains illustrations, and equation files. This important book: Contains a comprehensive reference to the science and engineering behind propulsion and power in sustainable air transportation Examines the impact of air transportation on the environment Covers alternative jet fuels and hybrid-electric propulsion and power Discusses modern propulsion for transonic, supersonic and hypersonic aircraft Examines the impact of propulsion system integration on aircraft design Written for engineers, graduate and senior undergraduate students in mechanical and aerospace engineering, Future Propulsion Systems and Energy Sources in Sustainable Aviation explores the future of aviation with a guide to sustainable air transportation that includes alternative jet fuels, hybrid-electric propulsion, all-electric and nuclear propulsion.
Download or read book The Power for Flight written by Jeremy R. Kinney and published by Government Printing Office. This book was released on 2018-02-15 with total page 318 pages. Available in PDF, EPUB and Kindle. Book excerpt: The NACA and aircraft propulsion, 1915-1958 -- NASA gets to work, 1958-1975 -- The shift toward commercial aviation, 1966-1975 -- The quest for propulsive efficiency, 1976-1989 -- Propulsion control enters the computer era, 1976-1998 -- Transiting to a new century, 1990-2008 -- Toward the future
Download or read book Real time Coastal Observing Systems for Marine Ecosystem Dynamics and Harmful Algal Blooms written by Babin, Marcel and published by UNESCO. This book was released on 2008-06-05 with total page 880 pages. Available in PDF, EPUB and Kindle. Book excerpt: The proliferation of harmful phytoplankton in marine ecosystems can cause massive fish kills, contaminate seafood with toxins, impact local and regional economies and dramatically affect ecological balance. Real-time observations are essential for effective short-term operational forecasting, but observation and modelling systems are still being developed. This volume provides guidance for developing real-time and near real-time sensing systems for observing and predicting plankton dynamics, including harmful algal blooms, in coastal waters. The underlying theory is explained and current trends in research and monitoring are discussed.Topics covered include: coastal ecosystems and dynamics of harmful algal blooms; theory and practical applications of in situ and remotely sensed optical detection of microalgal distributions and composition; theory and practical applications of in situ biological and chemical sensors for targeted species and toxin detection; integrated observing systems and platforms for detection; diagnostic and predictive modelling of ecosystems and harmful algal blooms, including data assimilation techniques; observational needs for the public and government; and future directions for research and operations.
Download or read book Engineering Design Optimization written by Joaquim R. R. A. Martins and published by Cambridge University Press. This book was released on 2021-11-18 with total page 653 pages. Available in PDF, EPUB and Kindle. Book excerpt: Based on course-tested material, this rigorous yet accessible graduate textbook covers both fundamental and advanced optimization theory and algorithms. It covers a wide range of numerical methods and topics, including both gradient-based and gradient-free algorithms, multidisciplinary design optimization, and uncertainty, with instruction on how to determine which algorithm should be used for a given application. It also provides an overview of models and how to prepare them for use with numerical optimization, including derivative computation. Over 400 high-quality visualizations and numerous examples facilitate understanding of the theory, and practical tips address common issues encountered in practical engineering design optimization and how to address them. Numerous end-of-chapter homework problems, progressing in difficulty, help put knowledge into practice. Accompanied online by a solutions manual for instructors and source code for problems, this is ideal for a one- or two-semester graduate course on optimization in aerospace, civil, mechanical, electrical, and chemical engineering departments.
Download or read book Innovation in Flight written by Joseph R. Chambers and published by . This book was released on 2005 with total page 406 pages. Available in PDF, EPUB and Kindle. Book excerpt:
