Download or read book Computational Analysis of Fretting Fatigue written by Yangjian Xu and published by . This book was released on 2009 with total page 114 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Characterization of Fretting Fatigue Process Volume Using Finite Element Analysis written by DR. Swalla and published by . This book was released on 2003 with total page 19 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fretting fatigue damage is characterized by the nucleation of cracks very early in the life of a component along a critical plane at an oblique angle to the contact surface. The number of cycles to fretting fatigue crack nucleation as well as the orientation of the initial crack critical plane is strongly influenced by the large stress and strain gradients that occur within a small volume near the fretting contact. Therefore, it is necessary to average the stresses and strains along a critical plane within a fretting fatigue process volume (FFPV) to obtain more reliable crack nucleation predictions. An approach for computing damage in a FFPV using finite element analysis is presented. The life and crack angle prediction is consistent with experimental observations of fretting fatigue tests on PH 13-8 Mo stainless steel. This averaging method allows for the introduction of a length scale for crack nucleation prediction.
Download or read book An Analysis of Fretting Fatigue written by D. Nowell and published by . This book was released on 1988 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Mechanics of Fretting Fatigue written by D.A. Hills and published by Springer Science & Business Media. This book was released on 2013-03-09 with total page 251 pages. Available in PDF, EPUB and Kindle. Book excerpt: Failures of many mechanical components in service result from fatigue. The cracks which grow may either originate from some pre-existing macroscopic defect, or, if the component is of high integrity but highly stressed, a region of localized stress concentration. In turn, such concentrators may be caused by some minute defect, such as a tiny inclusion, or inadvertent machining damage. Another source of surface damage which may exist between notionally 'bonded' components is associated with minute relative motion along the interface, brought about usually be cyclic tangential loading. Such fretting damage is quite insidious, and may lead to many kinds of problems such as wear, but it is its influence on the promotion of embryo cracks with which we are concerned here. When the presence of fretting is associated with decreased fatigue performance the effect is known as fretting fatigue. Fretting fatigue is a subject drawing equally on materials science and applied mechanics, but it is the intention in this book to concentrate attention entirely on the latter aspects, in a search for the quantification of the influence of fretting on both crack nucleation and propagation. There have been very few previous texts in this area, and the present volume seeks to cover five principal areas; (a) The modelling of contact problems including partial slip under tangentialloading, which produces the surface damage. (b) The modelling of short cracks by rigorous methods which deal effectively with steep stress gradients, kinking and closure. (c) The experimental simulation of fretting fatigue.
Download or read book Fretting Wear and Fretting Fatigue written by Tomasz Liskiewicz and published by Elsevier. This book was released on 2022-12-07 with total page 656 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fretting Wear and Fretting Fatigue: Fundamental Principles and Applications takes a combined mechanics and materials approach, providing readers with a fundamental understanding of fretting phenomena, related modeling and experimentation techniques, methods for mitigation, and robust examples of practical applications across an array of engineering disciplines. Sections cover the underpinning theories of fretting wear and fretting fatigue, delve into experimentation and modeling methods, and cover a broad array of applications of fretting fatigue and fretting wear, looking at its impacts in medical implants, suspension ropes, bearings, heating exchangers, electrical connectors, and more. Covers theoretical fundamentals, modeling and experimentation techniques, and applications of fretting wear and fatigue Takes a combined mechanics and materials approach Discusses the differences and similarities between fretting wear and fretting fatigue as well as combined experimental and modeling methods Covers applications including medical implants, heat exchangers, bearings, automotive components, gas turbines, and more
Download or read book Fatigue Analysis of a Paper Airplane written by Michael R. Urban Ph.D. and published by Covenant Books, Inc.. This book was released on 2023-10-02 with total page 121 pages. Available in PDF, EPUB and Kindle. Book excerpt: Accounting for fatigue loadings has been a concern ever since the widespread introduction of metallic materials into load-bearing components in the nineteenth century. Calculations were developed based on the analysis capabilities of their time incorporating all the latest technologies of their era. At the time, that technology was pencil-and-paper calculations. Today's calculations are computer-based. The widespread use of computing methods has greatly enhanced the analyst abilities for simulating internal stress and strain fields. Unfortunately, current fatigue analyses often force-fit current stress field calculations into fatigue analysis methods meant for nineteenth century stress calculation methods. It's never a good idea to force methods optimized for pre-computer calculations to work with computers. This text presents a more integrated approach to computer-based fatigue analysis methods. Like what was originally done, the latest technologies are applied rather than force-fitting computer computational capabilities into nineteenth-century techniques. Holistic approaches incorporating all knowledge have long been established as the most successful approach to problem-solving. Incorporating all knowledge with the most modern capabilities is the preferred approach. Holistic methods strive to reduce subjective inputs and replace them with consistent objective ones. This text aims to transition disjointed inefficient analyses into a unified computer-based holistic technique by introducing a fatigue analysis method specifically developed for computer simulations. Ultimately, for any method or theory to be valuable, it must be put into practice and prove itself. That entails leadership decision-making. Engineering design development activities will lead to final decisions. Information in a holistic approach must include the reliability of the information. How consistent are the predictions? Are the two types of potential scatter, analytic, and physical properly addressed? Is analytic scatter minimized while maintaining creativity? Is physical scatter totally understood? Effective program management requires knowledge on both types of scatter and, most importantly, the ability to realize the difference. A novel computer-based unified approach to fatigue methods is presented which incorporates a holistic approach for more accurate and consistent analyses, including the management and leadership of fatigue analysis projects, minimization of analytic scatter, management of physical scatter, and unification of methods that minimize subjective inputs often needed to bridge inconsistent techniques.
Download or read book Mechanics of Fretting and Fretting Fatigue written by David A. Hills and published by Springer Nature. This book was released on 2021-04-25 with total page 231 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book, which has only one very distant forerunner authored by David A. Hills with David Nowell, represents a very big step that is the quantification of these problems and represents the twenty-five years’ worth of work which have gone on at Oxford since the first book on the subject. Fatigue (popularly ‘metal fatigue’) is the primary failure mode of all machines, engines, transmissions and indeed almost all mechanical devices. The propagation of cracks is well understood and is treated in the subject Fracture Mechanics. By contrast, the nucleation of cracks is very hard to quantify and this remains the case with so-called ‘free initiation’ and, to a lesser extent, at cracks nucleated from stress raising features. But the third form of nucleation, where cracks start from the edges of rubbing components, that is, at joints, is potentially a very much better-defined environment, and therefore, the problem is amendable to attack by applied mechanics and experiment. The contents are of value both to those embarking on research on the subject and to practitioner in industry.
Download or read book Fretting Fatigue written by Steven E. Kinyon and published by ASTM International. This book was released on 2003 with total page 445 pages. Available in PDF, EPUB and Kindle. Book excerpt: Contains 29 contributions drawn from the Third International Symposium on Fretting Fatigue held in Nagaoka, Japan in May 2001. Sections of the volume address fretting wear and crack initiation; fretting fatigue crack and damage; life prediction; fretting fatigue parameter effects; loading condition
Download or read book Comparative Analysis of Three Fretting Fatigue Fixtures Preprint written by and published by . This book was released on 2006 with total page 29 pages. Available in PDF, EPUB and Kindle. Book excerpt: Three fixtures for conducting laboratory fretting fatigue tests are described and their respective testing methods and the results of the analysis are compared. Each of these fixtures has been used to investigate the effects of various parameters of interest in fretting fatigue. These fixtures include a unique apparatus in which all load applied to the specimen is transferred to the fretting pads, an apparatus similar to many found in the literature where partial load transfer occurs across the pads, and a simplified dovetail fixture in which the clamping load, P, and the shear load, Q, are varied in phase. Select test conditions from prior experiments performed on identical material and resulting in similar lives ranging from 1 to 10 million cycles from these fixtures are identified. The various testing conditions were used to compute the unique stress field for each case. The resulting contact stresses were used to calculate crack initiation based criteria, and to calculate stress intensity factors. The three fixtures were shown to be able to accommodate a range of loads, fretting pad contours, and specimen geometries that produced a variety of stress fields. A crack-initiation-based criterion was shown to predict the failure lives of thinner specimens accurately. The stress intensity factor calculations showed the possibility of a crack arresting for a stress field that decays rapidly and the possibility of a local minimum for K as a function of depth. The fixtures are shown to be complementary in generating data for development of robust fretting fatigue models that use these criteria.
Download or read book Fretting Wear Fretting Fatigue and Damping of Structures written by Toshio Hattori and published by Springer Nature. This book was released on 2023-12-26 with total page 402 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a comprehensive overview of the mechanical distinctions between fretting damage under axial or bending external forces and fretting damage under a torsional load. It emphasizes the importance of studying practical accident cases to efficiently acquire technical skills. The book is structured around the fundamental technologies of material science, tribology, and mechanics, which are vital for understanding and addressing technical issues. The author has incorporated all fretting countermeasure technologies, which were previously often sensory and empirical in nature, and repositioned them as technologies grounded in fundamental principles. The book proposes an economical approach to product operation that maintains reliability by integrating not only design technology but also maintenance practices. It delves into specific materials, such as titanium alloys and aluminum alloys, which have seen increased use for weight reduction in industries like aerospace. In this book, “Critical Distance Stress Theory” that can easily derive the fatigue limit and fatigue life of the stress singular field at the contact edge was presented. As a result, the fretting fatigue strength and life can be predicted from the same FEM stress analysis as the normal stress concentration part. And finally, introducing a novel fretting mechanical model, the book focuses on scenarios where pressure force (N) and repeated tangential force (F) are applied to two planar objects, with the tangential force being transmitted solely through friction at the contact surface. This model finds relevance in turbine blade connection structures, among other applications. The author references Asai's research example, which encompasses fretting mechanical analysis, fretting wear evaluation, fatigue assessment, and structural damping evaluation using this model.
Download or read book The Study of Fretting Fatigue Using Finite Element Analysis and Electron Microscopy written by B. Doeser and published by . This book was released on 1981 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book An Analysis of Fretting Damage on Fatigue Strength written by Hsing-chung Yeh and published by . This book was released on 1975 with total page 76 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Applied Fracture Mechanics written by Alexander Belov and published by IntechOpen. This book was released on 2012-12-12 with total page 394 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book "Applied Fracture Mechanics" presents a collection of articles on application of fracture mechanics methods to materials science, medicine, and engineering. In thirteen chapters, a wide range of topics is discussed, including strength of biological tissues, safety of nuclear reactor components, fatigue effects in pipelines, environmental effects on fracture among others. In addition, the book presents mathematical and computational methods underlying the fracture mechanics applications, and also developments in statistical modeling of fatigue. The work presented in this book will be useful, effective, and beneficial to mechanical engineers, civil engineers, and material scientists from industry, research, and education.
Download or read book Computational Modeling for Stress Analysis of Overhead Transmission Line Stranded Conductors Under Design and Fretting Fatigue Conditions written by Gang Qi and published by . This book was released on 2014 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: "While great efforts have been made in the electrical utility industry to engineer various stranded conductors with enhanced strength and vibrational characteristics, research devoted to understanding the complex mechanical behavior of complete conductors has been scarce, especially from a computational mechanics perspective. In the meanwhile, the long-lasting problem of conductor fretting fatigue becomes increasingly critical for overhead line design and maintenance, especially with the world-wide aging of electrical transmission grids. Aging of conductors contributes to significant degradation of their local fatigue strength, leading to drastic reduction of their service life.
Download or read book Fretting Fatigue written by David W. Hoeppner and published by ASTM International. This book was released on 2000 with total page 584 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume includes 36 of the 40 papers presented at the symposium, and a collection of six keynote papers providing background on the subject. Topics covered include parameter effects, environmental effects, crack nucleation, material and microstructural effects, damage analysis, fracture mechanic
Download or read book Characterization of Fretting Fatigue Damage by SEM Analysis written by G. L. Goss and published by . This book was released on with total page 19 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book A Fretting Fatigue Analysis Particularly Applied to Pin Joints written by J. N. Hammar and published by . This book was released on 1984 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
