Download or read book Cohesive Zone Modeling of Structural Joint Failure written by Matthew N. Cavalli and published by . This book was released on 2003 with total page 382 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Structural Adhesive Joints written by K. L. Mittal and published by John Wiley & Sons. This book was released on 2020-07-21 with total page 352 pages. Available in PDF, EPUB and Kindle. Book excerpt: Most structures are comprised of a number of individual parts or components which have to be connected to form a system with integral load transmission path. The structural adhesive bonding represents one of the most enabling technologies to fabricate most complex structural configurations involving advanced materials (e.g. composites) for load-bearing applications. Quite recently there has been a lot of activity in harnessing nanotechnology (use of nanomaterials) in ameliorating the existing or devising better performing structural adhesives. The 10 chapters by subject matter experts look at the following issues: Surface preparation for structural adhesive joints (SAJ) Use of nanoparticles in enhancing performance of SAJ Optimization of SAJ Durability aspects of SAJ Debonding of SAJ Fracture mechanics of SAJ Failure analysis of SAJ Damage behavior in functionally graded SAJ Impact, shock and vibration characteristics of composites for SAJ Delamination arrest methods in SAJ

Download or read book Adhesive Joining of Structural Components written by Alessandro Pegoretti and published by SAE International. This book was released on 2018-08-09 with total page 134 pages. Available in PDF, EPUB and Kindle. Book excerpt: Adhesive bonding has been used in the manufacture of primary aircraft fuselage and wing structures by various constructors since 1945. By a proper design, adhesive bonding often helps in designing structures mechanically equivalent to or even stronger than conventional assemblies. Adhesive Joining of Structural Components: New Insights and Technologies introduces the reader to some recent progress involved in adhesive joining of structural components. The chapters, seminal SAE International technical papers, cover the most recent advances in adhesive materials, surface preparation and controls, innovative bonding technologies, hybrid bonded/bolted joints, non-destructive testing and failure modelling of adhesively bonded joints. Edited by Dr. Alessandro Pegoretti, Professor of Materials Science and Technology at the University of Trento, Italy, Adhesive Joining of Structural Components: New Insights and Technologies is a must-read resource for those interested in the field of adhesive joining of structural components, which will assume an increasingly important role in designing and manufacturing lightweight structures. In fact, recent advancements in adhesives, methods for surface preparation and control, bonding technologies, non-destructive testing and modelling of failure mechanisms will certainly contribute to revitalize this relatively "mature" assembling technique.

Download or read book Modeling of Adhesively Bonded Joints written by Lucas F. M. da Silva and published by Springer Science & Business Media. This book was released on 2008-10-14 with total page 335 pages. Available in PDF, EPUB and Kindle. Book excerpt: A lot of recent developments have been made about adhesively bonded joints modeling using various methods of analysis. The increasing application of adhesives in industry is partly due to the increased sophistication and reliability of adhesive joints modeling. The book proposed intends to provide the designer with the most advanced stress analyses techniques in adhesive joints to reinforce the use of this promising bonding technique.

Download or read book Advances in Numerical Modeling of Adhesive Joints written by Lucas Filipe Martins da Silva and published by Springer Science & Business Media. This book was released on 2011-10-15 with total page 98 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book deals with the most recent numerical modeling of adhesive joints. Advances in damage mechanics and extended finite element method are described in the context of the Finite Element method with examples of application. The book also introduces the classical continuum mechanics and fracture mechanics approach and discusses the boundary element method and the finite difference method with indication of the cases they are most adapted to. At the moment there a no numerical technique that can solve any problem and the analyst needs to be aware of the limitations involved in each case.

Download or read book Handbook of Adhesion Technology written by Lucas F. M. da Silva and published by Springer. This book was released on 2011-08-10 with total page 1554 pages. Available in PDF, EPUB and Kindle. Book excerpt: Adhesives have been used for thousands of years, but until 100 years ago, the vast majority was from natural products such as bones, skins, fish, milk, and plants. Since about 1900, adhesives based on synthetic polymers have been introduced, and today, there are many industrial uses of adhesives and sealants. It is difficult to imagine a product—in the home, in industry, in transportation, or anywhere else for that matter—that does not use adhesives or sealants in some manner. The Handbook of Adhesion Technology is intended to be the definitive reference in the field of adhesion. Essential information is provided for all those concerned with the adhesion phenomenon. Adhesion is a phenomenon of interest in diverse scientific disciplines and of importance in a wide range of technologies. Therefore, this handbook includes the background science (physics, chemistry and materials science), engineering aspects of adhesion and industry specific applications. It is arranged in a user-friendly format with ten main sections: theory of adhesion, surface treatments, adhesive and sealant materials, testing of adhesive properties, joint design, durability, manufacture, quality control, applications and emerging areas. Each section contains about five chapters written by internationally renowned authors who are authorities in their fields. This book is intended to be a reference for people needing a quick, but authoritative, description of topics in the field of adhesion and the practical use of adhesives and sealants. Scientists and engineers of many different backgrounds who need to have an understanding of various aspects of adhesion technology will find it highly valuable. These will include those working in research or design, as well as others involved with marketing services. Graduate students in materials, processes and manufacturing will also want to consult it.

Download or read book Porous Rock Fracture Mechanics written by Amir Shojaei and published by Woodhead Publishing. This book was released on 2017-05-05 with total page 337 pages. Available in PDF, EPUB and Kindle. Book excerpt: Porous Rock Failure Mechanics: Hydraulic Fracturing, Drilling and Structural Engineering focuses on the fracture mechanics of porous rocks and modern simulation techniques for progressive quasi-static and dynamic fractures. The topics covered in this volume include a wide range of academic and industrial applications, including petroleum, mining, and civil engineering. Chapters focus on advanced topics in the field of rock’s fracture mechanics and address theoretical concepts, experimental characterization, numerical simulation techniques, and their applications as appropriate. Each chapter reflects the current state-of-the-art in terms of the modern use of fracture simulation in industrial and academic sectors. Some of the major contributions in this volume include, but are not limited to: anisotropic elasto-plastic deformation mechanisms in fluid saturated porous rocks, dynamics of fluids transport in fractured rocks and simulation techniques, fracture mechanics and simulation techniques in porous rocks, fluid-structure interaction in hydraulic driven fractures, advanced numerical techniques for simulation of progressive fracture, including multiscale modeling, and micromechanical approaches for porous rocks, and quasi-static versus dynamic fractures in porous rocks. This book will serve as an important resource for petroleum, geomechanics, drilling and structural engineers, R&D managers in industry and academia. Includes a strong editorial team and quality experts as chapter authors Presents topics identified for individual chapters are current, relevant, and interesting Focuses on advanced topics, such as fluid coupled fractures, rock’s continuum damage mechanics, and multiscale modeling Provides a ‘one-stop’ advanced-level reference for a graduate course focusing on rock’s mechanics

Download or read book Composite Joints and Connections written by P Camanho and published by Elsevier. This book was released on 2011-10-12 with total page 537 pages. Available in PDF, EPUB and Kindle. Book excerpt: The growing use of composites over metals for structural applications has made a thorough understanding of the behaviour of composite joints in various applications essential for engineers, but has also presented them with a new set of problems. Composite joints and connections addresses these differences and explores the design, modelling and testing of bonded and bolted joints and connections. Part one discusses bolted joints whilst part two examines bonded joints. Chapters review reinforcement techniques and applications for composite bolted and bonded joints and investigate the causes and effects of fatigue and stress on both types of joint in various applications and environments. Topics in part one include metal hybridization, glass-reinforced aluminium (GLARE), hybrid fibre metal laminates (FML), glass fibre reinforced polymer (GFRP) and carbon fibre reinforced polymer (CFRP) composites. Topics in part two include calculation of strain energy release rates, simulating fracture and fatigue failure using cohesive zone models, marine and aerospace applications, advanced modelling, stress analysis of bonded patches and scarf repairs. Composite joints and connections is a valuable reference for composite manufacturers and composite component fabricators, the aerospace, automotive, shipbuilding and civil engineering industries and for anyone involved in the joining and repair of composite structures. Explores the design, modelling and testing of bonded and bolted joints and connections Reviews reinforcement techniques and applications for composite bolted and bonded joints Investigates the causes and effects of fatigue and stress on bolted and bonded joints in various applications and environments

Download or read book Failure Analysis of Brazed Joints Using the CZM Approach written by Morvarid Karimi Ghovanlou and published by . This book was released on 2011 with total page 160 pages. Available in PDF, EPUB and Kindle. Book excerpt: Brazing, as a type of joining process, is widely used in manufacturing industries to join individual components of a structure. Structural reliability of a brazed assembly is strongly dependent on the joint mechanical properties. In the present work, mechanical reliability of low carbon steel brazed joints with copper filler metal is investigated and a methodology for failure analysis of brazed joints using the cohesive zone model (CZM) is presented. Mechanical reliability of the brazed joints is characterized by strength and toughness. Uniaxial and biaxial strengths of the joints are evaluated experimentally and estimated by finite element method using the ABAQUS software. Microstructural analysis of the joint fracture surfaces reveals different failure mechanisms of dimple rupture and dendritic failure. Resistance of the brazed joints against crack propagation, evaluated by the single-parameter fracture toughness criterion, shows dependency on the specimen geometry and loading configuration. Fracture of the brazed joints and the subsequent ductile tearing process are investigated using a two-parameter CZM. The characterizing model parameters of the cohesive strength and cohesive energy are identified by a four-point bend fracture test accompanied with corresponding FE simulation. Using the characterized CZM, the joint fracture behavior under tensile loading is well estimated. Predictability of the developed cohesive zone FE model for fracture analysis of brazed joints independent of geometry and loading configuration is validated. The developed cohesive zone FE model is extended to fatigue crack growth analysis in brazed joints. A cyclic damage evolution law is implemented into the cohesive zone constitutive model to irreversibly account for the joint stiffness degradation over the number of cycles. Fatigue failure behavior of the brazed joints is characterized by performing fully reversed strain controlled cyclic tests. The damage law parameters are calibrated based on the analytical solutions and the experimental fatigue crack growth data. The characterized irreversible CZM shows applicability to fatigue crack growth life prediction of brazed joints.

Download or read book Progress in the Analysis and Design of Marine Structures written by Carlos Guedes Soares and published by CRC Press. This book was released on 2017-04-28 with total page 2192 pages. Available in PDF, EPUB and Kindle. Book excerpt: Progress in the Analysis and Design of Marine Structures collects the contributions presented at MARSTRUCT 2017, the 6th International Conference on Marine Structures (Lisbon, Portugal, 8-10 May 2017). The MARSTRUCT series of Conferences started in Glasgow, UK in 2007, the second event of the series having taken place in Lisbon, Portugal in March 2009, the third in Hamburg, Germany in March 2011, the fourth in Espoo, Finland in March 2013, and the fifth in Southampton, UK in March 2015. This Conference series deals with Ship and Offshore Structures, addressing topics in the areas of: - Methods and Tools for Loads and Load Effects - Methods and Tools for Strength Assessment - Experimental Analysis of Structures - Materials and Fabrication of Structures - Methods and Tools for Structural Design and Optimisation, and - Structural Reliability, Safety and Environmental Protection Progress in the Analysis and Design of Marine Structures is essential reading for academics, engineers and all professionals involved in the design of marine and offshore structures.

Download or read book Quasibrittle Fracture Mechanics and Size Effect written by Jia-Liang Le and published by Oxford University Press. This book was released on 2021-11-19 with total page 332 pages. Available in PDF, EPUB and Kindle. Book excerpt: Many modern engineering structures are composed of brittle heterogenous, or quasibrittle, materials. These include concrete, composites, tough ceramics, rocks, cold asphalt mixtures, and many brittle materials at the microscale. Understanding the failure behavior of these materials is of paramount importance for improving the resilience and sustainability of various engineering structures including civil infrastructure, aircraft, ships, military armors, and microelectronic devices. Designed for graduate and upper-level undergraduate university courses, this textbook provides a comprehensive treatment of quasibrittle fracture mechanics. It includes a concise but rigorous examination of linear elastic fracture mechanics, which is the foundation of all fracture mechanics. It also covers the fundamental concepts of nonlinear fracture mechanics, and introduces more advanced concepts such as triaxial stress state in the fracture process zone, nonlocal continuum models, and discrete computational models. Finally, the book features extensive discussion of the various practical applications of quasibrittle fracture mechanics across different structures and engineering disciplines, and throughout includes exercises and problems for students to test their understanding.

Download or read book Strength Prediction of Adhesively Bonded Joints written by Raul D. S. G. Campilho and published by CRC Press. This book was released on 2017-05-25 with total page 670 pages. Available in PDF, EPUB and Kindle. Book excerpt: Adhesively-bonded joints provide many advantages over conventional mechanical fasteners and are increasingly receiving attention as an alternative to mechanical joints in engineering applications. The traditional fasteners usually result in the cutting of fibers and hence the introduction of stress concentrations, both of which reduce structural integrity. By contrast, bonded joints are more continuous and have potential advantages of strength-to-weight ratio, design flexibility, and ease of fabrication. This book provides an overview of available analytical methods as well as numerical methods.

Download or read book Numerical Modelling of Failure in Advanced Composite Materials written by Pedro P. Camanho and published by Woodhead Publishing. This book was released on 2015-08-07 with total page 562 pages. Available in PDF, EPUB and Kindle. Book excerpt: Numerical Modelling of Failure in Advanced Composite Materials comprehensively examines the most recent analysis techniques for advanced composite materials. Advanced composite materials are becoming increasingly important for lightweight design in aerospace, wind energy, and mechanical and civil engineering. Essential for exploiting their potential is the ability to reliably predict their mechanical behaviour, particularly the onset and propagation of failure. Part One investigates numerical modeling approaches to interlaminar failure in advanced composite materials. Part Two considers numerical modelling approaches to intralaminar failure. Part Three presents new and emerging advanced numerical algorithms for modeling and simulation of failure. Part Four closes by examining the various engineering and scientific applications of numerical modeling for analysis of failure in advanced composite materials, such as prediction of impact damage, failure in textile composites, and fracture behavior in through-thickness reinforced laminates. Examines the most recent analysis models for advanced composite materials in a coherent and comprehensive manner Investigates numerical modelling approaches to interlaminar failure and intralaminar failure in advanced composite materials Reviews advanced numerical algorithms for modeling and simulation of failure Examines various engineering and scientific applications of numerical modelling for analysis of failure in advanced composite materials

Download or read book An Evaluation of Cohesive Zone Models for Adhesive Failure in Binded Joints written by Sobia Iqbal Waqar and published by . This book was released on 2011 with total page 327 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Advances in Structural Adhesive Bonding written by David A. Dillard and published by Elsevier. This book was released on 2010-03-31 with total page 654 pages. Available in PDF, EPUB and Kindle. Book excerpt: Adhesive bonding is often effective, efficient, and often necessary way to join mechanical structures. This important book reviews the most recent improvements in adhesive bonding and their wide-ranging potential in structural engineering. Part one reviews advances in the most commonly used groups of structural adhesives with chapters covering topics such as epoxy, polyurethane, silicone, cyanoacrylate, and acrylic adhesives. The second set of chapters covers the various types of adherends and pre-treatment methods for a range of structural materials such as metals, composites and plastics. Chapters in Part three analyse methods and techniques with topics on joint design, life prediction, fracture mechanics and testing. The final group of chapters gives useful and practical insights into the problems and solutions of adhesive bonding in a variety of hostile environments such as chemical, wet and extreme temperatures. With its distinguished editor and international team of contributors, Advances in structural adhesive bonding is a standard reference for structural and chemical engineers in industry and the academic sector. Reviews advances in the most commonly used groups of structural adhesives including epoxy, silicone and acrylic adhesives Examines key issues in adhesive selection featuring substrate compatibility and manufacturing demands Documents advances in bonding metals, plastics and composites recognising problems and limitations

Download or read book ICCS19 19th International Conference on Composite Structures written by Antonio J.M. Ferreira and published by Società Editrice Esculapio. This book was released on 2016-08-01 with total page 212 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nowadays, it is quite easy to see various applications of fibrous composites, functionally graded materials, laminated composite, nano-structured reinforcement, morphing composites, in many engineering fields, such as aerospace, mechanical, naval and civil engineering. The increase in the use of composite structures in different engineering practices justify the present international meeting where researches from every part of the globe can share and discuss the recent advancements regarding the use of standard structural components within advanced applications such as buckling, vibrations, repair, reinforcements, concrete, composite laminated materials and more recent metamaterials. For this reason, the establishment of this 19th edition of International Conference on Composite Structures has appeared appropriate to continue what has been begun during the previous editions. ICCS wants to be an occasion for many researchers from each part of the globe to meet and discuss about the recent advancements regarding the use of composite structures, sandwich panels, nanotechnology, bio-composites, delamination and fracture, experimental methods, manufacturing and other countless topics that have filled many sessions during this conference. As a proof of this event, which has taken place in Porto (Portugal), selected plenary and keynote lectures have been collected in the present book.

Download or read book Strength Prediction of Adhesively Bonded Joints written by Raul D. S. G. Campilho and published by CRC Press. This book was released on 2017-05-25 with total page 422 pages. Available in PDF, EPUB and Kindle. Book excerpt: Adhesively-bonded joints provide many advantages over conventional mechanical fasteners and are increasingly receiving attention as an alternative to mechanical joints in engineering applications. The traditional fasteners usually result in the cutting of fibers and hence the introduction of stress concentrations, both of which reduce structural integrity. By contrast, bonded joints are more continuous and have potential advantages of strength-to-weight ratio, design flexibility, and ease of fabrication. This book provides an overview of available analytical methods as well as numerical methods.