Download or read book Advanced District Heating and Cooling DHC Systems written by Robin Wiltshire and published by Woodhead Publishing. This book was released on 2015-08-31 with total page 365 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advanced District Heating and Cooling (DHC) Systems presents the latest information on the topic, providing valuable information on the distribution of centrally generated heat or cold energy to buildings, usually in the form of space heating, cooling, and hot water. As DHC systems are more efficient and less polluting than individual domestic or commercial heating and cooling systems, the book provides an introduction to DHC, including its potential contribution to reducing carbon dioxide emissions, then reviews thermal energy generation for DHC, including fossil fuel-based technologies, those based on renewables, and surplus heat valorization. Final sections address methods to improve the efficiency of DHC. - Gives a comprehensive overview of DHC systems and the technologies and energy resources utilized within these systems - Analyzes the various methods used for harnessing energy to apply to DHC systems - Ideal resource for those interested in district cooling, teleheating, heat networks, distributed heating, thermal energy, cogeneration, combined heat and power, and CHP - Reviews the application of DHC systems in the field, including both the business model side and the planning needed to implement these systems

Download or read book Cogeneration Fuel Cell Sorption Air Conditioning Systems written by I. Pilatowsky and published by Springer Science & Business Media. This book was released on 2011-01-28 with total page 171 pages. Available in PDF, EPUB and Kindle. Book excerpt: Although conventional cogeneration systems have been used successfully in the last two decades, most of them have been large units using mainly hydrocarbon fuels that are becoming increasingly expensive. New cogeneration systems based on fuel cells and sorption air conditioning systems promise to be an energy-saving alternative for situations when cooling, heating and power are needed at low and medium capacities. Cogeneration Fuel Cell-Sorption Air Conditioning Systems examines the thermodynamic principles of fuel cell performance and sorption air conditioning systems, and gives relevant information about the state of the art of these technologies. It also provides the reader with the theoretical bases and knowledge needed to understand the operation of these new cogeneration systems, as well as discussing the design basis and economical evaluation. Topics covered include: • selected fuel cells for cogeneration CHP processes; • state-of-the-art sorption refrigeration systems; • potential applications in demonstration projects; and • profitability assessment of the cogeneration system. Air conditioning and fuel cell engineers; postgraduates and researchers in energy fields; and designers of cooling, heating and power cogeneration systems will find Cogeneration Fuel Cell-Sorption Air Conditioning Systems a useful and informative reference.

Download or read book Power Generation Technologies written by Paul Breeze and published by Elsevier. This book was released on 2005-02-04 with total page 289 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book makes intelligible the wide range of electricity generating technologies available today, as well as some closely allied technologies such as energy storage. The book opens by setting the many power generation technologies in the context of global energy consumption, the development of the electricity generation industry and the economics involved in this sector. A series of chapters are each devoted to assessing the environmental and economic impact of a single technology, including conventional technologies, nuclear and renewable (such as solar, wind and hydropower). The technologies are presented in an easily digestible form.Different power generation technologies have different greenhouse gas emissions and the link between greenhouse gases and global warming is a highly topical environmental and political issue. With developed nations worldwide looking to reduce their emissions of carbon dioxide, it is becoming increasingly important to explore the effectiveness of a mix of energy generation technologies.Power Generation Technologies gives a clear, unbiased review and comparison of the different types of power generation technologies available. In the light of the Kyoto protocol and OSPAR updates, Power Generation Technologies will provide an invaluable reference text for power generation planners, facility managers, consultants, policy makers and economists, as well as students and lecturers of related Engineering courses.· Provides a unique comparison of a wide range of power generation technologies - conventional, nuclear and renewable· Describes the workings and environmental impact of each technology· Evaluates the economic viability of each different power generation system

Download or read book Cogeneration written by Christos A. Frangopoulos and published by IET. This book was released on 2017-03-10 with total page 361 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a comprehensive, integrated treatment of cogeneration technologies and systems. Also called combined heat and power (CHP), cogeneration is the use of a power station to deliver two or more useful forms of energy (e.g. generating electricity and heat at the same time). All conventional, fuel-based plants generate heat as by-product, which is often wasted. Cogeneration captures part of this heat for delivery to consumers. The book gives a tour of the available cogeneration technologies and their features. It provides plenty of instructive examples of cogeneration projects to illustrate key concepts, and also covers the relevant regulatory and legal frameworks. It is an ideal text/reference for anyone working in power systems and energy engineering. Topics covered include: * Benefits of cogeneration * Cogeneration technologies * Electrical engineering aspects * Applications of cogeneration * Fuels for cogeneration systems * Thermodynamic analysis * Environmental impacts of cogeneration * Reliability and availability * Economic analysis of cogeneration systems * Regulatory and legal frameworks * Selection, integration and operation of cogeneration systems * Simulation and optimisation * Synthesis, design and operation * Examples of cogeneration projects * Research and development of cogeneration * Summary and conclusions

Download or read book Small and Micro Combined Heat and Power CHP Systems written by R Beith and published by Elsevier. This book was released on 2011-04-30 with total page 553 pages. Available in PDF, EPUB and Kindle. Book excerpt: Small and micro combined heat and power (CHP) systems are a form of cogeneration technology suitable for domestic and community buildings, commercial establishments and industrial facilities, as well as local heat networks. One of the benefits of using cogeneration plant is a vastly improved energy efficiency: in some cases achieving up to 80–90% systems efficiency, whereas small-scale electricity production is typically at well below 40% efficiency, using the same amount of fuel. This higher efficiency affords users greater energy security and increased long-term sustainability of energy resources, while lower overall emissions levels also contribute to an improved environmental performance.Small and micro combined heat and power (CHP) systems provides a systematic and comprehensive review of the technological and practical developments of small and micro CHP systems.Part one opens with reviews of small and micro CHP systems and their techno-economic and performance assessment, as well as their integration into distributed energy systems and their increasing utilisation of biomass fuels. Part two focuses on the development of different types of CHP technology, including internal combustion and reciprocating engines, gas turbines and microturbines, Stirling engines, organic Rankine cycle process and fuel cell systems. Heat-activated cooling (i.e. trigeneration) technologies and energy storage systems, of importance to the regional/seasonal viability of this technology round out this section. Finally, part three covers the range of applications of small and micro CHP systems, from residential buildings and district heating, to commercial buildings and industrial applications, as well as reviewing the market deployment of this important technology.With its distinguished editor and international team of expert contributors, Small and micro combined heat and power (CHP) systems is an essential reference work for anyone involved or interested in the design, development, installation and optimisation of small and micro CHP systems. - Reviews small- and micro-CHP systems and their techno-economic and performance assessment - Explores integration into distributed energy systems and their increasing utilisation of biomass fuels - Focuses on the development of different types of CHP technology, including internal combustion and reciprocating engines

Download or read book Smart Grid R Evolution written by Jennie C. Stephens and published by Cambridge University Press. This book was released on 2015-02-26 with total page 217 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book explores smart grid from a social perspective, for advanced students, academic researchers, and energy professionals.

Download or read book Combined Heating Cooling Power Handbook written by Neil Petchers and published by The Fairmont Press, Inc.. This book was released on 2003 with total page 888 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Renewable Energy Systems written by Martin Kaltschmitt and published by Springer. This book was released on 2012-12-06 with total page 1898 pages. Available in PDF, EPUB and Kindle. Book excerpt: Humanity is facing a steadily diminishing supply of fossil fuels, causing researchers, policy makers, and the population as a whole to turn increasingly to alternative and especially renewable sources of energy to make up this deficit. Gathering over 80 peer-reviewed entries from the Encyclopedia of Sustainability Science and Technologies, Renewable Energy Systems provides an authoritative introduction to a wide variety of renewable energy sources. State-of-the-art coverage includes geothermal power stations, ocean energy, renewable energy from biomass, waste to energy, and wind power. This comprehensive, two-volume work provides an excellent introduction for those entering these fields, as well as new insights for advanced researchers, industry experts, and decision makers.

Download or read book Conversion of Coal Fired Power Plants to Cogeneration and Combined Cycle written by Ryszard Bartnik and published by Springer Science & Business Media. This book was released on 2011-07-28 with total page 158 pages. Available in PDF, EPUB and Kindle. Book excerpt: Conversion of Coal-Fired Power Plant to Cogeneration and Combined-Cycle presents the methodology, calculation procedures and tools used to support enterprise planning for adapting power stations to cogeneration and combined-cycle forms. The authors analyze the optimum selection of the structure of heat exchangers in a 370 MW power block, the structure of heat recovery steam generators and gas turbines. Conversion of Coal-Fired Power Plant to Cogeneration and Combined-Cycle also addresses the problems of converting existing power plants to dual-fuel gas-steam combined-cycle technologies coupled with parallel systems. Conversion of Coal-Fired Power Plant to Cogeneration and Combined-Cycle is an informative monograph written for researchers, postgraduate students and policy makers in power engineering.

Download or read book Exergy Analysis and Thermoeconomics of Buildings written by Jose M Sala-Lizarraga and published by Butterworth-Heinemann. This book was released on 2019-10-01 with total page 1116 pages. Available in PDF, EPUB and Kindle. Book excerpt: Quantifying exergy losses in the energy supply system of buildings reveals the potential for energy improvement, which cannot be discovered using conventional energy analysis. Thermoeconomics combines economic and thermodynamic analysis by applying the concept of cost (an economic concept) to exergy, as exergy is a thermodynamic property fit for this purpose, in that it combines the quantity of energy with its quality factor. Exergy Analysis and Thermoeconomics of Buildings applies exergy analysis methods and thermoeconomics to the built environment. The mechanisms of heat transfer throughout the envelope of buildings are analyzed from an exergy perspective and then to the building thermal installations, analyzing the different components, such as condensing boilers, absorption refrigerators, microcogeneration plants, etc., including solar installations and finally the thermal facilities as a whole. A detailed analysis of the cost formation process is presented, which has its physical roots firmly planted in the second law of thermodynamics. The basic principles and the rules of cost allocation, in energy units (exergy cost), in monetary units (exergoeconomic cost), and in CO2 emissions (exergoenvironmental cost), based on the so-called Exergy Cost Theory are presented and applied to thermal installations of buildings. Clear and rigorous in its exposition, Exergy Analysis and Thermoeconomics of Buildings discusses exergy analysis and thermoeconomics and the role they could play in the analysis and design of building components, either the envelope or the thermal facilities, as well as the diagnosis of thermal installations. This book moves progressively from introducing the basic concepts to applying them. Exergy Analysis and Thermoeconomics of Buildings provides examples of specific cases throughout this book. These cases include real data, so that the results obtained are useful to interpret the inefficiencies and losses that truly occur in actual installations; hence, the assessment of their effects encourages the manner to improve efficiency. - Applies exergy analysis methods for the installation of building thermal facilities equipment components, including pipes, valves, heat exchangers, boilers and heat pumps - Helps readers determine the operational costs of heating and cooling building systems - Includes exergy analysis methods that are devoted to absorption refrigerators, adsorption cooling systems, basic air conditioning processes, ventilation systems and solar systems, either thermal and PV - Discusses the direct application of exergy analysis concepts, including examples of buildings with typical heating, DHW and air conditioning installations

Download or read book The Role of Bioenergy in the Emerging Bioeconomy written by Carmen Lago and published by Academic Press. This book was released on 2018-10-16 with total page 592 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Role of Bioenergy in the Bioeconomy: Resources, Technologies, Sustainability and Policy provides the reader with a complete understanding on how bioenergy technologies fit into the new bioeconomy paradigm. Sections focus on the main resources and technologies for bioenergy and its integration in energy systems and biorefining chains, analyze the available methodologies for assessing the sustainability of bioenergy, and address and the propose approaches that are demonstrated through concrete case studies. Additionally, the implications of bioenergy in the water-energy and land nexus is presented, along with new challenges and opportunities. This book's strong focus on sustainability of bioenergy, both as a standalone, and in the larger context of a bio-based economy, makes it a useful resource for researchers, professionals and students in the bioenergy field who need tactics to assess the lifecycle and sustainability of bioenergy technologies and their integration into existing systems. - Presents a complete overview of the main challenges that bioenergy will have to overcome in order to play a key role in future energy systems - Explores sustainability aspects in detail, both qualitatively and by applying proposed methodologies to concrete bioenergy case studies - Covers, in detail, the water-energy-land nexus implications and governance aspects

Download or read book European Law on Combined Heat and Power written by Maciej M. Sokołowski and published by Routledge. This book was released on 2020-03-11 with total page 269 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides an analysis of the European policy approach to combined heat and power (CHP), a highly efficient technology used by all EU Member States for the needs of generating electricity and heat. European Law on Combined Heat and Power carries out an assessment of the European legal and policy measures on CHP, evaluating how it has changed over the years through progress and decline in specific member states. Over the course of the book, Sokołowski explores all aspects of CHP, examining the types of measures used to steer the growth of cogeneration in the EU and the policies and regulatory tools that have influenced its development. He also assesses the specific role of CHP in the liberalisation of the internal energy market and EU action on climate and sustainability. Finally, by delivering his notions of "cogenatives", "cogenmunities", or "Micro-Collective-Flexible-Smart-High-Efficiency cogeneration", Sokołowski considers how the new EU energy package – "Clean energy for all Europeans" – will shape future developments. This book will be of great interest to students and scholars of energy law and regulation, combined heat and power and energy efficiency, as well as policy makers and energy experts working in the CHP sector.

Download or read book Handbook for Cogeneration and Combined Cycle Power Plants written by Meherwan P. Boyce and published by American Society of Mechanical Engineers. This book was released on 2010 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Covers the aspects of power plant design, operation, and maintenance. This title discusses cycle optimization and reliability, technical details on sizing, plant layout, fuel selection, types of drives, and performance characteristics of the major components in a cogeneration or combined cycle power plant.

Download or read book Cogeneration and Polygeneration Systems written by Majid Amidpour and published by Academic Press. This book was released on 2020-11-23 with total page 406 pages. Available in PDF, EPUB and Kindle. Book excerpt: Cogeneration and Polygeneration Systems explores the suite of state-of-the-art modeling, design, analysis and optimization procedures for creating and retooling optimally efficient combined heat and power (CHP) and polygeneration energy systems. The book adopts exergetic and thermoeconomic analysis and related modeling and simulation tools to inform performance and systems design in modern cogeneration plants. Chapters provide a methodical approach to the design, operation and troubleshooting of cogeneration systems when they are integrated with industrial processes. Cogeneration targets, environmental impacts, total site integration, and availability and reliability issues are addressed in-depth. Explores exergetic and exergoeconomic analysis for optimization purposes of CHP systems Addresses availability and reliability issues within cogeneration systems Reviews modern polygeneration systems based on renewable energy resources and fuel cells

Download or read book Cogeneration combined Heat and Power CHP written by J. H. Horlock and published by Krieger Publishing Company. This book was released on 1997-01-01 with total page 226 pages. Available in PDF, EPUB and Kindle. Book excerpt: This text provides an introduction to all aspects of combined heat and power (CHP) thermodynamics, design, economics and utilization. Emphasis is placed on the performance of CHP plants compared to conventional plants, and the economic considerations in combined heat and power utilization. There are many CHP installations in commission and, where applicable, the text describes practical examples of CHP use.

Download or read book Sustainable Vehicle Technologies written by Institution of Mechanical Engineers and published by Elsevier. This book was released on 2012-11-06 with total page 249 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book contains the papers from the IMechE's Sustainable Vehicle Technologies 2012 conference. An innovative technical conference organised by the Automobile Division of the IMechE, it follows on from the 2009 Low Carbon Vehicle conference, which established a high standard with presentations primarily focussed on powertrain technology. The conference examines the latest advances in technology with a view towards understanding the consequences of carbon dioxide reduction over the entire vehicle lifecycle. Papers cover all aspects of the finite resources available for vehicle production, operation and recycling. - Presents the papers from this leading conference - Covers life time emissions and sustainability over the entire product life-cycle - Considers all areas of environmental pollution in addition to the goals for delivering low-carbon vehicles

Download or read book Electricity Production from Renewables written by Rui Castro and published by Springer Nature. This book was released on 2022-01-01 with total page 415 pages. Available in PDF, EPUB and Kindle. Book excerpt: This textbook is about economically competitive renewable energy sources (RES), including onshore and offshore wind, solar and small-hydro plants, and focusing on the electricity production from these sources. Clearly divided into sections discussing the different RES, the textbook begins with an introduction of AC electrical circuits, aimed at non-electrical engineers. It then offers an economic assessment of renewable energy projects, before discussing photovoltaic technologies and concentrated solar power. It explores the theory of wind to power conversion, electrical generator types and electrical part of offshore systems. Presenting theoretical concepts related to the electrical framework associated with RES, alongside examples and solved problems, this book will clearly introduce the topic of renewable power sources to graduate students, researchers and practitioners alike. After reading the book, readers will be equipped to make a preliminary techno-economic assessment of a RES.