Download or read book CMOS Low Noise Amplifier Design Utilizing Monolithic Transformers written by Jianjun J. Zhou and published by . This book was released on 1998 with total page 350 pages. Available in PDF, EPUB and Kindle. Book excerpt: Full integration of CMOS low noise amplifiers (LNA) presents a challenge for low cost CMOS receiver systems. A critical problem faced in the design of an RF CMOS LNA is the inaccurate high-frequency noise model of the MOSFET implemented in circuit simulators such as SPICE. Silicon-based monolithic inductors are another bottleneck in RF CMOS design due to their poor quality factor. In this thesis, a CMOS implementation of a fully-integrated differential LNA is presented. A small-signal noise circuit model that includes the two most important noise sources of the MOSFET at radio frequencies, channel thermal noise and induced gate current noise, is developed for CMOS LNA analysis and simulation. Various CMOS LNA architectures are investigated. The optimization techniques and design guidelines and procedures for an LC tuned CMOS LNA are also described. Analysis and modeling of silicon-based monolithic inductors and transformers are presented and it is shown that in fully-differential applications, a monolithic transformer occupies less die area and achieves a higher quality factor compared to two independent inductors with the same total effective inductance. It is also shown that monolithic transformers improve the common-mode rejection of the differential circuits.

Download or read book Triple Band CMOS Low Noise Amplifier Design Utilizing Transformer Couplings written by and published by . This book was released on 2016 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book CMOS Low Noise Amplifiers for Single and Multiband Applications A Comprehensive Design Approach written by Norlaili Mohd Noh, Farshad Eshghabadi, Arjuna Marzuki and published by Penerbit USM. This book was released on 2023-10-11 with total page 481 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides comprehensive knowledge, aimed at practicing integrated circuit design engineer or researcher, to learn and design a low noise amplifier (LNA) for single and multiband applications. The content is structured in a way so that even a beginner can follow the design method easily. This book features the following characteristics: different types of LNA designs (with key building blocks) are discussed, and detailed analysis is given for each LNA design, which covers from the fundamental and principal knowledge to the justification of the design approach. Detailed design approaches are using 180 nm and 130nm CMOS technologies, purposely presented in this manner to give exposure to the design of LNA under different technologies. The LNAs in this book are designed for GSM, WCDMA and WLAN standards, but the same method can be used for other frequencies of operation. Comprehensive analyses on the extreme or corner condition effects are highlighted. Besides, detailed derivation of equations relating to the parameters of the LNA’s performance metrics help LNA designers in understanding how the performance metrics of the LNA can be optimized to meet the desired specification. Electromagnetic analyses using Sonnet, an electromagnetic tool able to replace the conventional post-layout simulation with resistance and capacitance parasitic extraction for more accurate frequency performance prediction are presented. The electromagnetic method is proposed to be used in the LNA design as it can accurately predict the LNA’s performance before tape-out for first-pass fabrication. MATLAB codes are provided to generate important S-parameters and noise figure values.

Download or read book Parasitic Aware Optimization of CMOS RF Circuits written by David J. Allstot and published by Springer Science & Business Media. This book was released on 2005-12-02 with total page 169 pages. Available in PDF, EPUB and Kindle. Book excerpt: In the arena of parasitic-aware design of CMOS RF circuits, efforts are aimed at the realization of true single-chip radios with few, if any, off-chip components. The parasitic-aware RF circuit synthesis techniques described in this book effectively address critical problems in this field.

Download or read book High Linearity CMOS RF Front End Circuits written by Yongwang Ding and published by Springer Science & Business Media. This book was released on 2006-02-08 with total page 132 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on high performance radio frequency integrated circuits (RF IC) design in CMOS. 1. Development of radio frequency ICs Wireless communications has been advancing rapidly in the past two decades. Many high performance systems have been developed, such as cellular systems (AMPS, GSM, TDMA, CDMA, W-CDMA, etc. ), GPS system (global po- tioning system) and WLAN (wireless local area network) systems. The rapid growth of VLSI technology in both digital circuits and analog circuits provides benefits for wireless communication systems. Twenty years ago not many p- ple could imagine millions of transistors in a single chip or a complete radio for size of a penny. Now not only complete radios have been put in a single chip, but also more and more functions have been realized by a single chip and at a much lower price. A radio transmits and receives electro-magnetic signals through the air. The signals are usually transmitted on high frequency carriers. For example, a t- ical voice signal requires only 30 Kilohertz bandwidth. When it is transmitted by a FM radio station, it is often carried by a frequency in the range of tens of megahertz to hundreds of megahertz. Usually a radio is categorized by its carrier frequency, such as 900 MHz radio or 5 GHz radio. In general, the higher the carrier frequency, the better the directivity, but the more difficult the radio design.

Download or read book Analog Circuit Design written by Arthur H.M. van Roermund and published by Springer Science & Business Media. This book was released on 2005-12-30 with total page 395 pages. Available in PDF, EPUB and Kindle. Book excerpt: Number 12 in the successful series of Analog Circuit Design provides valuable information and excellent overviews of analogue circuit design, CAD and RF systems. The series is an ideal reference for those involved in analogue and mixed-signal design.

Download or read book LNA ESD Co Design for Fully Integrated CMOS Wireless Receivers written by Paul Leroux and published by Springer Science & Business Media. This book was released on 2006-03-30 with total page 199 pages. Available in PDF, EPUB and Kindle. Book excerpt: LNA-ESD Co-Design for Fully Integrated CMOS Wireless Receivers fits in the quest for complete CMOS integration of wireless receiver front-ends. With a combined discussion of both RF and ESD performance, it tackles one of the final obstacles on the road to CMOS integration. The book is conceived as a design guide for those actively involved in the design of CMOS wireless receivers. The book starts with a comprehensive introduction to the performance requirements of low-noise amplifiers in wireless receivers. Several popular topologies are explained and compared with respect to future technology and frequency scaling. The ESD requirements are introduced and related to the state-of-the-art protection devices and circuits. LNA-ESD Co-Design for Fully Integrated CMOS Wireless Receivers provides an extensive theoretical treatment of the performance of CMOS low-noise amplifiers in the presence of ESD-protection circuitry. The influence of the ESD-protection parasitics on noise figure, gain, linearity, and matching are investigated. Several RF-ESD co-design solutions are discussed allowing both high RF-performance and good ESD-immunity for frequencies up to and beyond 5 GHz. Special attention is also paid to the layout of both active and passive components. LNA-ESD Co-Design for Fully Integrated CMOS Wireless Receivers offers the reader intuitive insight in the LNA’s behavior, as well as the necessary mathematical background to optimize its performance. All material is experimentally verified with several CMOS implementations, among which a fully integrated GPS receiver front-end. The book is essential reading for RF design engineers and researchers in the field and is also suitable as a text book for an advanced course on the subject.

Download or read book Direct Conversion Receivers in Wide Band Systems written by Aarno Pärssinen and published by Springer Science & Business Media. This book was released on 2006-04-18 with total page 250 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is based on my doctoral thesis at the Helsinki University of Technology. Several different projects during five years guided me from the basics of the RF IC design to the implementations of highly integrated radio receiver chips. Sharing time and effort between IC and system issues is not always straightforward. I have been lucky to follow both topics and share experiences with diligent and enthusiastic people having different specialities. As a result, this book will cover a wide range of different topics needed in the design of highly integrated radio receivers. Experiences from the first receiver prototypes for the third generation cellular systems form the basis of this book. Most of the issues are directly related to the early proposals of European and Japanese standardization organizations. For example, the chip rate was originally set to 4. 096 Mcps in a wide-band CDMA channel. I have kept that number in the book in most of the examples although it has been later changed to 3. 84 Mcps. I hope that the readers will accept that and the possible other incompabilities to the latest specifications. At least in the research phase the changes even in the most essential requirements are definitely not a rare incident and IC designers should be able to react and modify their designs as soon as they can.

Download or read book Linear RF CMOS Circuit Design written by Yongwang Ding and published by . This book was released on 2004 with total page 290 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book CMOS Analog IC Design for 5G and Beyond written by Sangeeta Singh and published by Springer Nature. This book was released on 2021-02-07 with total page 163 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is focused on addressing the designs of FinFET-based analog ICs for 5G and E-band communication networks. In addition, it also incorporates some of the contemporary developments over different fields. It highlights the latest advances, problems and challenges and presents the latest research results in the field of mm-wave integrated circuits designing based on scientific literature and its practical realization. The traditional approaches are excluded in this book. The authors cover various design guidelines to be taken care for while designing these circuits and detrimental scaling effects on the same. Moreover, Gallium Nitrides (GaN) are also reported to show huge potentials for the power amplifier designing required in 5G communication network. Subsequently, to enhance the readability of this book, the authors also include real-time problems in RFIC designing, case studies from experimental results, and clearly demarking design guidelines for the 5G communication ICs designing. This book incorporates the most recent FinFET architecture for the analog IC designing and the scaling effects along with the GaN technology as well.

Download or read book Radio Frequency Fully monolithic CMOS Low Noise Amplifier written by Arif Mahmud and published by . This book was released on 2000 with total page 440 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Dissertation Abstracts International written by and published by . This book was released on 2007 with total page 924 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Millimeter Wave Low Noise Amplifiers written by Mladen Božanić and published by Springer. This book was released on 2017-11-30 with total page 344 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is the first standalone book that combines research into low-noise amplifiers (LNAs) with research into millimeter-wave circuits. In compiling this book, the authors have set two research objectives. The first is to bring together the research context behind millimeter-wave circuit operation and the theory of low-noise amplification. The second is to present new research in this multi-disciplinary field by dividing the common LNA configurations and typical specifications into subsystems, which are then optimized separately to suggest improvements in the current state-of-the-art designs. To achieve the second research objective, the state-of-the-art LNA configurations are discussed and the weaknesses of state-of the art configurations are considered, thus identifying research gaps. Such research gaps, among others, point towards optimization – at a systems and microelectronics level. Optimization topics include the influence of short wavelength, layout and crosstalk on LNA performance. Advanced fabrication technologies used to decrease the parasitics of passive and active devices are also explored, together with packaging technologies such as silicon-on-chip and silicon-on-package, which are proposed as alternatives to traditional IC implementation. This research outcome builds through innovation. Innovative ideas for LNA construction are explored, and alternative design methodologies are deployed, including LNA/antenna co-design or utilization of the electronic design automation in the research flow. The book also offers the authors’ proposal for streamlined automated LNA design flow, which focuses on LNA as a collection of highly optimized subsystems.

Download or read book Circuits at the Nanoscale written by Krzysztof Iniewski and published by CRC Press. This book was released on 2018-10-08 with total page 602 pages. Available in PDF, EPUB and Kindle. Book excerpt: Circuits for Emerging Technologies Beyond CMOS New exciting opportunities are abounding in the field of body area networks, wireless communications, data networking, and optical imaging. In response to these developments, top-notch international experts in industry and academia present Circuits at the Nanoscale: Communications, Imaging, and Sensing. This volume, unique in both its scope and its focus, addresses the state-of-the-art in integrated circuit design in the context of emerging systems. A must for anyone serious about circuit design for future technologies, this book discusses emerging materials that can take system performance beyond standard CMOS. These include Silicon on Insulator (SOI), Silicon Germanium (SiGe), and Indium Phosphide (InP). Three-dimensional CMOS integration and co-integration with Microelectromechanical (MEMS) technology and radiation sensors are described as well. Topics in the book are divided into comprehensive sections on emerging design techniques, mixed-signal CMOS circuits, circuits for communications, and circuits for imaging and sensing. Dr. Krzysztof Iniewski is a director at CMOS Emerging Technologies, Inc., a consulting company in Vancouver, British Columbia. His current research interests are in VLSI ciruits for medical applications. He has published over 100 research papers in international journals and conferences, and he holds 18 international patents granted in the United States, Canada, France, Germany, and Japan. In this volume, he has assembled the contributions of over 60 world-reknown experts who are at the top of their field in the world of circuit design, advancing the bank of knowledge for all who work in this exciting and burgeoning area.

Download or read book Design of Low Noise Amplifiers for Ultra Wideband Communications written by Roberto Díaz Ortega and published by McGraw Hill Professional. This book was released on 2014-01-13 with total page 129 pages. Available in PDF, EPUB and Kindle. Book excerpt: Cutting-edge techniques for ultra-wideband, low-noise amplifier design This pioneering resource presents alternatives for implementing power- and area-efficient integrated low-noise amplifiers for ultra-wideband communications. Design methodologies for distributed amplifiers, feedback amplifiers, inductor structures with reduced area, and inductorless techniques are discussed. Cowritten by international experts in industry and academia, this book addresses the state of the art in integrated circuit design in the context of emerging systems. Design of Low-Noise Amplifiers for Ultra-Wideband Communications covers: Ultra-wideband overview and system approach Distributed amplifiers Wideband low-noise amplifiers Feedback wideband low-noise amplifiers Inductorless techniques

Download or read book Advances in Monolithic Microwave Integrated Circuits for Wireless Systems Modeling and Design Technologies written by Marzuki, Arjuna and published by IGI Global. This book was released on 2011-08-31 with total page 380 pages. Available in PDF, EPUB and Kindle. Book excerpt: Monolithic Microwave Integrated Circuit (MMIC) is an electronic device that is widely used in all high frequency wireless systems. In developing MMIC as a product, understanding analysis and design techniques, modeling, measurement methodology, and current trends are essential.Advances in Monolithic Microwave Integrated Circuits for Wireless Systems: Modeling and Design Technologies is a central source of knowledge on MMIC development, containing research on theory, design, and practical approaches to integrated circuit devices. This book is of interest to researchers in industry and academia working in the areas of circuit design, integrated circuits, and RF and microwave, as well as anyone with an interest in monolithic wireless device development.

Download or read book Wideband Low Noise Amplifiers Exploiting Thermal Noise Cancellation written by Federico Bruccoleri and published by Springer Science & Business Media. This book was released on 2006-03-30 with total page 191 pages. Available in PDF, EPUB and Kindle. Book excerpt: Low Noise Amplifiers (LNAs) are commonly used to amplify signals that are too weak for direct processing for example in radio or cable receivers. Traditionally, low noise amplifiers are implemented via tuned amplifiers, exploiting inductors and capacitors in resonating LC-circuits. This can render very low noise but only in a relatively narrow frequency band close to resonance. There is a clear trend to use more bandwidth for communication, both via cables (e.g. cable TV, internet) and wireless links (e.g. satellite links and Ultra Wideband Band). Hence wideband low-noise amplifier techniques are very much needed. Wideband Low Noise Amplifiers Exploiting Thermal Noise Cancellation explores techniques to realize wideband amplifiers, capable of impedance matching and still achieving a low noise figure well below 3dB. This can be achieved with a new noise cancelling technique as described in this book. By using this technique, the thermal noise of the input transistor of the LNA can be cancelled while the wanted signal is amplified! The book gives a detailed analysis of this technique and presents several new amplifier circuits. This book is directly relevant for IC designers and researchers working on integrated transceivers. Although the focus is on CMOS circuits, the techniques can just as well be applied to other IC technologies, e.g. bipolar and GaAs, and even in discrete component technologies.