Download or read book Catalytic Ignition Properties of Canola methyl ester and Soybean methyl ester in Oxygen nitrogen Mixtures Over Platinum rhodium written by Bradley S. McGary and published by . This book was released on 2011 with total page 174 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Catalytic Ignition of Oxygen nitrogen ethanol Mixtures Over a 90 Platinum 10 Rhodium Alloy in Comparison with Pure Platinum written by David G. Mehaffey and published by . This book was released on 2011 with total page 110 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Catalytic Ignition and Combustion of Lean Mixtures written by C. K. Law and published by . This book was released on 1984 with total page 160 pages. Available in PDF, EPUB and Kindle. Book excerpt: Ignition and heat release rates of fuel/oxygen/nitrogen over platinum wires are experimentally studied using micro-calorimetry, aiming to gain additional understanding on the complex transport and kinetic processes involved during catalytic oxidation so as to relate the macroscopic observables with the microscopic behavior. The fuels studied are propane, butane, propylene, ethylene, carbon monoxide and hydrogen. Parameters investigated include catalyst surface temperature, fuel and oxygen concentrations, and flow velocity. Results show that for very low Reynolds number flows the flow velocity has negligible influences on the ignition temperature. Its influence on the heat release rates is also negligible but only for the reactions in kinetically controlled regime. Variation of fuel concentration is found to be an important factor in that the ignition temperatures of propane and butane decrease as their concentrations are increased from lean to rich mixtures while the opposite trend is observed for propylene, ethylene, carbon monoxide and hydrogen.
Download or read book Combustion Performance and Emissions of Soybean Methyl Ester Fuel in a DI Diesel Engine written by Kyle William Scholl and published by . This book was released on 1985 with total page 260 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Canola Methyl Ester biodiesel Emission Study written by Zenneth Faye and published by . This book was released on 1996 with total page 12 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Canola Methyl Ester biodiesel Emission Study Final Report written by Faye, Zenneth and published by [Regina] : Agriculture Development Fund. This book was released on 1996 with total page 12 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Effect of Oxygen Content on Soot Formation in a Co flow Diffusion Flame Fueled with Canola Methyl Ester and Diesel written by Stephanie Virginia Prado Carbonell and published by . This book was released on 2021 with total page 103 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Soybean Oil Derivatives for Fuel and Chemical Feedstocks written by and published by . This book was released on 2013 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Plant based sources of hydrocarbons are being considered as alternatives to petrochemicals because of the need to conserve petroleum resources for reasons of national security and climate change. Changes in fuel formulations to include ethanol from corn sugar and methyl esters from soybean oil are examples of this policy in the United States and elsewhere. Replacements for commodity chemicals are also being considered, as this value stream represents much of the profit for the oil industry and one that would be affected by shortages in oil or other fossil fuels. While the discovery of large amounts of natural gas associated with oil shale deposits has abated this concern, research into bio-based feedstock materials continues. In particular, this chapter reviews a literature on the conversion of bio-based extracts to hydrocarbons for fuels and for building block commodity chemicals, with a focus on soybean derived products. Conversion of methyl esters from soybean triglycerides for replacement of diesel fuel is an active area of research; however, the focus of this chapter will not reside with esterification or transesterification, except has a means to provide materials for the production of hydrocarbons for fuels or chemical feedstocks. Methyl ester content in vehicle fuel is limited by a number of factors, including the performance in cold weather, the effect of oxygen content on engine components particularly in the case of older engines, shelf-life, and higher NOx emissions from engines that are not tuned to handle the handle the enhanced pre-ignition conditions of methyl ester combustion [1]. These factors have led to interest in synthesizing a hydrocarbon fuel from methyl esters, one that will maintain the cetane number but will achieve better performance in an automobile: enhanced mixing, injection, and combustion, and reduce downstream issues such as emissions and upstream issues such as fuel preparation and transportation. Various catalytic pathways from oxygenated precursor to hydrocarbon will be considered in the review: pyrolysis [2], deoxygenation and hydrogenation [3, 4], and hydrotreatment [5]. The focus of many of these studies has been production of fuels that are miscible or fungible with petroleum products, e.g., the work published by the group of Daniel Resasco at U. Oklahoma [6]. Much of the published literature focuses on simpler chemical representatives of the methyl esters form soybean oil; but these results are directly applicable to the production of chemical feedstocks, such as ethylbenzene that can be used for a variety of products: polymers, solvent, and reagent [3]. Although many chemical pathways have been demonstrated in the laboratory, the scale-up to handle quantities of bio-derived material presents a number of challenges in comparison with petroleum refining. These range from additional transportation costs because of distributed feedstock production to catalyst cost and regeneration. Other chapters in the book appear to address the cultivation and harvesting of soybeans and production of oil, so these areas will not be dealt with directly in this chapter except as they may relate to chemical changes in the feedstock material. However, the feasibility of the production of hydrocarbons from soybean triglycerides or methyl esters derived from these triglycerides will be considered, along with remaining technical hurdles before soybeans can make a significant contribution to the hydrocarbon economy.
Download or read book Homogeneous Selective Hydrogenation of Soybean Methyl Ester written by John C. Bailar and published by . This book was released on 1971 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Processing of Soybean Oil Into Fuels written by and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Abundant and easily refined, petroleum has provided high energy density liquid fuels for a century. However, recent price fluctuations, shortages, and concerns over the long term supply and greenhouse gas emissions have encouraged the development of alternatives to petroleum for liquid transportation fuels (Van Gerpen, Shanks et al. 2004). Plant-based fuels include short chain alcohols, now blended with gasoline, and biodiesels, commonly derived from seed oils. Of plant-derived diesel feedstocks, soybeans yield the most of oil by weight, up to 20% (Mushrush, Willauer et al. 2009), and so have become the primary source of biomass-derived diesel in the United States and Brazil (Lin, Cunshan et al. 2011). Worldwide ester biodiesel production reached over 11,000,000 tons per year in 2008 (Emerging Markets 2008). However, soybean oil cannot be burned directly in modern compression ignition vehicle engines as a direct replacement for diesel fuel because of its physical properties that can lead to clogging of the engine fuel line and problems in the fuel injectors, such as: high viscosity, high flash point, high pour point, high cloud point (where the fuel begins to gel), and high density (Peterson, Cook et al. 2001). Industrial production of biodiesel from oil of low fatty-acid content often follows homogeneous base-catalyzed transesterification, a sequential reaction of the parent triglyceride with an alcohol, usually methanol, into methyl ester and glycerol products. The conversion of the triglyceride to esterified fatty acids improves the characteristics of the fuel, allowing its introduction into a standard compression engine without giving rise to serious issues with flow or combustion. Commercially available biodiesel, a product of the transesterification of fats and oils, can also be blended with standard diesel fuel up to a maximum of 20 vol.%. In the laboratory, the fuel characteristics of unreacted soybean oil have also been improved by dilution with petroleum based fuels, or by aerating and formation of microemulsions. However, it is the chemical conversion of the oil to fuel that has been the area of most interest. The topic has been reviewed extensively (Van Gerpen, Shanks et al. 2004), so this aspect will be the focus in this chapter. Important aspects of the chemistry of conversion of oil into diesel fuel remain the same no matter the composition of the triglyceride. Hence, although the focus in this book is on soybean oil, studies on other plant based oils and simulated oils have occasional mention in this chapter. Valuable data can be taken on systems that are simpler than soybean based oils, with fewer or shorter chain components. Sometimes the triglycerides will behave differently under reaction conditions, and when relevant, these have been noted in the text. Although the price of diesel fuel has increased, economical production of biodiesel is a challenge because of (1) the increasing price of soybean oil feedstocks and reagent methanol, (2) a distributed supply of feedstocks that reduces the potential for economies of scale, (3) processing conditions that include pressures and temperatures above ambient, and (4) multiple processing steps needed to reduce contaminant levels to ASTM specification D6751 limits (Vasudevan & Briggs 2008). Much of the cost of biodiesel production is related to the conversion of the oil to the methyl ester and so there has been an emphasis to research improved methods of converting soybean oil to biodiesel. However, most of these studies have taken place at the bench scale, and have not demonstrated a marked improvement in yield or reduced oil-to-methanol ratio in comparison with standard base-catalyzed transesterification. One aspect that has a short term chance of implementation is the improvement of the conversion process by the use of a continuous rather than batch process, with energy savings generated by combined reaction and separation, online analysis, and reagent methanol added by titration as needed to produce ASTM specification grade fuel. By adapting process intensification methods, recycled sources of soybean oil may also be used for diesel production, taking advantage of a lower priced feedstock material. Even if the economics of production are feasible, biodiesel distribution is complicated by thermal stability and degradation over time, and the physical properties of methyl esters make them undesirable for standard compression ignition engines in concentrations greater than 20% in a blend with diesel fuel. Generation of truly fungible fuel from biomass is now being investigated through a variety of routes. However, it is too early to judge which will become the most viable. The promise of soybean-generated biodiesel is that of a truly fungible, thermodynamically and economically viable technology bringing a biomass replacement to a petroleum product.
Download or read book Fundamentals of Combustion Processes written by Sara McAllister and published by Springer Science & Business Media. This book was released on 2011-05-10 with total page 315 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fundamentals of Combustion Processes is designed as a textbook for an upper-division undergraduate and graduate level combustion course in mechanical engineering. The authors focus on the fundamental theory of combustion and provide a simplified discussion of basic combustion parameters and processes such as thermodynamics, chemical kinetics, ignition, diffusion and pre-mixed flames. The text includes exploration of applications, example exercises, suggested homework problems and videos of laboratory demonstrations
Download or read book Food Emulsifiers and Their Applications written by Richard W Hartel and published by Springer Science & Business Media. This book was released on 2013-04-17 with total page 315 pages. Available in PDF, EPUB and Kindle. Book excerpt: Food emulsions have existed since long before people began to process foods for distribution and consumption. Milk, for example, is a natural emulsion/colloid in which a nutritional fat is stabilized by a milk-fat-globule membrane. Early processed foods were developed when people began to explore the art of cuisine. Butter and gravies were early foods used to enhance flavors and aid in cooking. By contrast, food emulsifiers have only recently been recognized for their abil ity to stabilize foods during processing and distribution. As economies of scale emerged, pressures for higher quality and extension of shelf life prodded the de velopment of food emulsifiers and their adjunct technologies. Natural emulsifiers, such as egg and milk proteins and phospholipids, were the first to be generally utilized. Development of technologies for processing oils, such as refining, bleaching, and hydrogenation, led to the design of synthetic food emulsifiers. Formulation of food emulsions has, until recently, been practiced more as an art than a science. The complexity offood systems has been the barrier to funda mental understanding. Scientists have long studied emulsions using pure water, hydrocarbon, and surfactant, but food systems, by contrast, are typically a com plex mixture of carbohydrate, lipid, protein, salts, and acid. Other surface-active ingredients, such as proteins and phospholipids, can demonstrate either syner- XV xvi Preface gistic or deleterious functionality during processing or in the finished food.
Download or read book Chemicals from Biomass written by Debalina Sengupta and published by CRC Press. This book was released on 2012-07-05 with total page 506 pages. Available in PDF, EPUB and Kindle. Book excerpt: Chemicals from Biomass: Integrating Bioprocesses into Chemical Production Complexes for Sustainable Development helps engineers optimize the development of new chemical and polymer plants that use renewable resources to replace the output of goods and services from existing plants. It also discusses the conversion of those existing plants into faci
Download or read book Advances in Biorefineries written by Keith W. Waldron and published by Elsevier. This book was released on 2014-04-28 with total page 939 pages. Available in PDF, EPUB and Kindle. Book excerpt: Biorefineries are an essential technology in converting biomass into biofuels or other useful materials. Advances in Biorefineries provides a comprehensive overview of biorefining processing techniques and technologies, and the biofuels and other materials produced. Part one focuses on methods of optimizing the biorefining process and assessing its environmental and economic impact. It also looks at current and developing technologies for producing value-added materials. Part two goes on to explore these materials with a focus on biofuels and other value-added products. It considers the properties, limitations, and practical applications of these products and how they can be used to meet the increasing demand for renewable and sustainable fuels as an alternative to fossil fuels. Advances in Biorefineries is a vital reference for biorefinery/process engineers, industrial biochemists/chemists, biomass/waste scientists and researchers and academics in the field. - A comprehensive and systematic reference on the advanced biomass recovery and conversion processes used in biorefineries - Reviews developments in biorefining processes - Discusses the wide range of value-added products from biorefineries, from biofuel to biolubricants and bioadhesives
Download or read book Edible Oil Processing written by Wolf Hamm and published by John Wiley & Sons. This book was released on 2013-08-05 with total page 360 pages. Available in PDF, EPUB and Kindle. Book excerpt: Oils and fats are almost ubiquitous in food processing, whether naturally occurring in foods or added as ingredients that bring functional benefits. Whilst levels of fat intake must be controlled in order to avoid obesity and other health problems, it remains the fact that fats (along with proteins and carbohydrates) are one of the three macronutrients and therefore an essential part of a healthy diet. The ability to process oils and fats to make them acceptable as part of our food supplies is a key component in our overall knowledge of them. Without this ability, the food that we consume would be totally different, and much of the flexibility available to us as a result of the application of processing techniques would be lost. Obviously we need to know how to process fatty oils, but we also need to know how best to use them once they have been processed. This second edition of Edible Oil Processing presents a valuable overview of the technology and applications behind the subject. It covers the latest technologies which address new environmental and nutritional requirements as well as the current state of world edible oil markets. This book is intended for food scientists and technologists who use oils and fats in food formulations, as well as chemists and technologists working in edible oils and fats processing.
Download or read book Gaseous Carbon Waste Streams Utilization written by National Academies of Sciences, Engineering, and Medicine and published by National Academies Press. This book was released on 2019-02-22 with total page 257 pages. Available in PDF, EPUB and Kindle. Book excerpt: In the quest to mitigate the buildup of greenhouse gases in Earth's atmosphere, researchers and policymakers have increasingly turned their attention to techniques for capturing greenhouse gases such as carbon dioxide and methane, either from the locations where they are emitted or directly from the atmosphere. Once captured, these gases can be stored or put to use. While both carbon storage and carbon utilization have costs, utilization offers the opportunity to recover some of the cost and even generate economic value. While current carbon utilization projects operate at a relatively small scale, some estimates suggest the market for waste carbon-derived products could grow to hundreds of billions of dollars within a few decades, utilizing several thousand teragrams of waste carbon gases per year. Gaseous Carbon Waste Streams Utilization: Status and Research Needs assesses research and development needs relevant to understanding and improving the commercial viability of waste carbon utilization technologies and defines a research agenda to address key challenges. The report is intended to help inform decision making surrounding the development and deployment of waste carbon utilization technologies under a variety of circumstances, whether motivated by a goal to improve processes for making carbon-based products, to generate revenue, or to achieve environmental goals.
Download or read book Electrochemical Water Splitting written by Inamuddin and published by Materials Research Forum LLC. This book was released on 2019-10-25 with total page 250 pages. Available in PDF, EPUB and Kindle. Book excerpt: Aiming at the generation of hydrogen from water, electrochemical water splitting represents a promising clean technology for generating a renewable energy resource. The book reviews the fundamental aspects and describes recent research advances. Properties and characterization methods for various types of electrocatalysts are discussed, including noble metals, earth-abundant metals, metal-organic frameworks, carbon nanomaterials and polymers. Keywords: Electrochemical Water Splitting, Renewable Energy Resource, Electrocatalysts, Oxygen Evolution Reaction (OER), Noble Metal Catalysts, Earth-Abundant Metal Catalysts, MOF Catalysts, Carbon-based Nanocatalysts, Polymer Catalysts, Transition Metal-based Electrocatalysts, Fe-based Electrocatalysts, Co-based Electrocatalysts, Ni-based Electrocatalysts, Metal Free Catalysts, Transition-Metal Chalcogenides, Prussian Blue Analogues.
