Download or read book Biomass Gasification for Gas Turbine Based Power Generation written by Mark A. Paisley and published by . This book was released on 1997 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Presented at the International Gas Turbine & Aeroengine Congress & Exhibition, Orlando, FL, Jun 2-Jun 5, 1997.

Download or read book BIOMASS GASIFICATION AND POWER GENERATION USING ADVANCED GAS TURBINE SYSTEMS written by and published by . This book was released on 2004 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: A multidisciplined team led by the United Technologies Research Center (UTRC) and consisting of Pratt & Whitney Power Systems (PWPS), the University of North Dakota Energy & Environmental Research Center (EERC), KraftWork Systems, Inc. (kWS), and the Connecticut Resource Recovery Authority (CRRA) has evaluated a variety of gasified biomass fuels, integrated into advanced gas turbine-based power systems. The team has concluded that a biomass integrated gasification combined-cycle (BIGCC) plant with an overall integrated system efficiency of 45% (HHV) at emission levels of less than half of New Source Performance Standards (NSPS) is technically and economically feasible. The higher process efficiency in itself reduces consumption of premium fuels currently used for power generation including those from foreign sources. In addition, the advanced gasification process can be used to generate fuels and chemicals, such as low-cost hydrogen and syngas for chemical synthesis, as well as baseload power. The conceptual design of the plant consists of an air-blown circulating fluidized-bed Advanced Transport Gasifier and a PWPS FT8 TwinPac[trademark] aeroderivative gas turbine operated in combined cycle to produce [approx]80 MWe. This system uses advanced technology commercial products in combination with components in advanced development or demonstration stages, thereby maximizing the opportunity for early implementation. The biofueled power system was found to have a levelized cost of electricity competitive with other new power system alternatives including larger scale natural gas combined cycles. The key elements are: (1) An Advanced Transport Gasifier (ATG) circulating fluid-bed gasifier having wide fuel flexibility and high gasification efficiency; (2) An FT8 TwinPac[trademark]-based combined cycle of approximately 80 MWe; (3) Sustainable biomass primary fuel source at low cost and potentially widespread availability-refuse-derived fuel (RDF); (4) An overall integrated system that exceeds the U.S. Department of Energy (DOE) goal of 40% (HHV) efficiency at emission levels well below the DOE suggested limits; and (5) An advanced biofueled power system whose levelized cost of electricity can be competitive with other new power system alternatives.

Download or read book Integrated Gasification Combined Cycle IGCC Technologies written by Ting Wang and published by Woodhead Publishing. This book was released on 2016-11-26 with total page 929 pages. Available in PDF, EPUB and Kindle. Book excerpt: Integrated Gasification Combined Cycle (IGCC) Technologies discusses this innovative power generation technology that combines modern coal gasification technology with both gas turbine and steam turbine power generation, an important emerging technology which has the potential to significantly improve the efficiencies and emissions of coal power plants. The advantages of this technology over conventional pulverized coal power plants include fuel flexibility, greater efficiencies, and very low pollutant emissions. The book reviews the current status and future developments of key technologies involved in IGCC plants and how they can be integrated to maximize efficiency and reduce the cost of electricity generation in a carbon-constrained world. The first part of this book introduces the principles of IGCC systems and the fuel types for use in IGCC systems. The second part covers syngas production within IGCC systems. The third part looks at syngas cleaning, the separation of CO2 and hydrogen enrichment, with final sections describing the gas turbine combined cycle and presenting several case studies of existing IGCC plants. Provides an in-depth, multi-contributor overview of integrated gasification combined cycle technologies Reviews the current status and future developments of key technologies involved in IGCC plants Provides several case studies of existing IGCC plants around the world

Download or read book Energy from Biomass written by Peter Quaak and published by World Bank Publications. This book was released on 1999 with total page 112 pages. Available in PDF, EPUB and Kindle. Book excerpt: While energy is essential for development, standard fossil fuels are often in short supply in countries where it is needed most. However, alternative fuel resources abound in the form of agricultural and municipal waste or "biomass." This report reviews the state of the art of biomass combustion and gassification systems, their advantages and disadvantages. It also encourages investment in use of these technologies to enable developing countries to better exploit their biomass resources and help close the gap between their energy needs and their energy supply.

Download or read book ADVANCED GASIFICATION BASED FUEL CONVERSION AND ELECTRIC ENERGY PRODUCTION SYSTEM written by and published by . This book was released on 2002 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt: Boise Paper Solutions and the Gas Technology Institute (GTI) are cooperating to develop, demonstrate and place in continuous operation an advanced biomass gasification-based power generation system suitable for near-term commercial deployment in the Forest Products Industry. The system will be used in conjunction with, rather than in place of, existing wood waste fired boilers and flue gas cleanup systems. The novel system will include three advanced technological components based on GTI's RENUGAS{reg_sign} and three-stage stoker combustion technologies, and a gas turbine-based power generation concept developed in DOE's High Performance Power System (HIPPS) program. The system has, as its objective, to avoid the major hurdles of high-pressure gasification, i.e., high-pressure fuel feeding and ash removal, and hot gas cleaning that are typical for conventional IGCC power generation. It aims to also minimize capital intensity and technology risks. The system is intended to meet the immediate needs of the forest products industry for highly efficient and environmentally friendly electricity and steam generation systems utilizing existing wood waste as fuel resources. The overall objective of this project is to demonstrate the commercial applicability of an advanced biomass gasification-based power generation system at Boise Paper Solutions' pulp and paper mill located at DeRidder, Louisiana.

Download or read book Gasification for Low grade Feedstock written by Yongseung Yun and published by BoD – Books on Demand. This book was released on 2018-07-11 with total page 290 pages. Available in PDF, EPUB and Kindle. Book excerpt: Most coveted energy forms nowadays are gas in nature and electricity due to their environmental cleanness and convenience. Recently, gasification market trend is starting to switch to low-grade feedstock such as biomass, wastes, and low-rank coal that are still not properly utilized. In this sense, the most promising area of development in gasification field lies in low-grade feedstock that should be converted to more user-friendly gas or electricity form in utilization. This book tried to shed light on the works on gasification from many parts of the world and thus can feel the technology status and the areas of interest regarding gasification for low-grade feedstock.

Download or read book Biomass in Small Scale Energy Applications written by Mateusz Szubel and published by CRC Press. This book was released on 2019-10-08 with total page 361 pages. Available in PDF, EPUB and Kindle. Book excerpt: Biomass in Small-Scale Energy Applications: Theory and Practice presents the current trends in the development of selected biomass-based technologies for distributed energy generation. It describes the methodology, experimental results, and computer simulations with a focus on pilot systems and devices crucial in multiple applications with related environmental/economic issues. It describes which stages of design, development, and application of advanced biomass-based energy devices are critical in order for a given technology to be successful. It includes both technical/practical information and theoretical background related to combustion kinetics, thermodynamics in energy systems, and properties of selected types of biomass, as well as case studies.

Download or read book Fuel Flexible Energy Generation written by John Oakey and published by Woodhead Publishing. This book was released on 2015-12-08 with total page 334 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fuel Flexible Energy Generation: Solid, Liquid and Gaseous Fuels provides updated information on flexible fuel energy generation, the process by which one or more fuels can be combusted in the same boiler or turbine to generate power. By adapting or building boilers and turbines to accept multiple fuel sources, they can be co-fired with biomass and waste derived fuels, allowing a reduction in carbon output, thus providing cleaner energy. Fuel flexibility is becoming more important in a world of diminishing fossil fuel stocks. Many countries are investing in the development of more efficient fuel flexible boilers and turbines, and their use is becoming more prevalent in industry as well. This book provides comprehensive coverage of flexible fuel energy generation across all potential fuel types, and was written by a selection of experts in the field who discuss the types of fuels which can be used in fuel flexible energy generation, from solid fuels to biomass fuels, the preparation of fuels to be used in fuel flexible operations, that includes their handling and transport, and combustion and conversion technologies with chapters ranging from large-scale coal gasification to technology options and plant design issues. Focuses on fuel flexibility across all potential fuel types Includes thorough treatment of the technology being developed to allow for fuel flexibility Written by leading experts in the field Provides an essential text for R&D managers in firms which produce boilers or turbines, those who work in the fuel industry, and academics working in engineering departments on energy generation

Download or read book Assessment of Novel Power Generation Systems for the Biomass Industry written by and published by . This book was released on 1911 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The objective of this programme of research is to produce a method for assessing and optimising the performance of advanced gas turbine power plants for electricity generation within the Brazilian electric sector. With the privatisation of the Brazilian electric sector, interest has been given to the thermal plants and studies have been carried out along with the use of other alternative fuels rather than fossil fuels. Biomass is a fuel of increasing interest for power generation systems since it is clean and renewable. Essentially all biomass power plants in the Brazilian market today operate on a steam Rankine cycle, which has a poor efficiency. The Brazilian electricity market has paid attention on Biomass integrated gasification gas turbine (BIG/GT) combined cycle plants where solid biomass is gasified. A simple chemical model for representing the gasifier in the power plant is presented and optimisation of the gasification process has been applied. The method for assessing the performance of power plants takes into account not only energy, but it applies the exergy method, which uses the second law of thermodynamics and works out the destruction of energy inside plant components and energy losses rejected to atmosphere. A thermoeconomic model for assessing the power plant has also been described. The optimisation of the assessment method of power plants using exergy and thermoeconomics has been proposed based on genetic algorithms. This new technique has been fairly successful at solving optimisation problems and is easy to implement. The decision of applying genetic algorithms is due to the complexity of the mathematical model applied in the performance assessment of power plants. The assessment of combined cycles like gas / steam cycle, gas / air cycle, gas / steam / freon cycle, gas / air / freon cycle and chemically recuperated gas turbine have been investigated. The application of the overall assessment method helps to understand different and very expensi.

Download or read book Gasification for Practical Applications written by Jens Omdahl and published by . This book was released on 2016-04-01 with total page 332 pages. Available in PDF, EPUB and Kindle. Book excerpt: Some of the most promising, attention-getting energy alternatives aren't revolutionary ideas. We all know about windmills and waterwheels, which have been around for centuries. Today, a variety of improvements, including innovative turbine designs, are transforming these ancient machines into cutting-edge technologies that can help nations satisfy their energy needs. There's another old process -- one you probably don't know much about -- that's gaining in popularity and may join wind and hydropower in the pantheon of clean, renewable energy. The process is known as gasification. Gasification is a partial oxidation process whereby a carbon source such as coal, natural gas or biomass, is broken down into carbon monoxide (CO) and hydrogen (H2), plus carbon dioxide (CO2) and possibly hydrocarbon molecules such as methane (CH4). This is achieved by reacting the material at high temperatures (>700 °C), without combustion, with a controlled amount of oxygen and/or steam. The resulting gas mixture is called syngas (from synthesis gas or synthetic gas) or producer gas and is itself a fuel. The power derived from gasification and combustion of the resultant gas is considered to be a source of renewable energy if the gasified compounds were obtained from biomass. Gasification is not a new technology; it was originally developed in the 1800s and is the processes used to make town gas for lighting and cooking. Small scale gasifiers were also used to power internal combustion engine vehicles during fuel shortages during the Second World War. If the gasification takes place at a relatively low temperature, such as 700oC to 1000oC, the product gas will have a relatively high level of hydrocarbons compared to high temperature gasification. As a result it may be used directly, to be burned for heat or electricity generation via a steam turbine or, with suitable gas clean up, to run an internal combustion engine for electricity generation. The book entitled Gasification for Practical Applications provides the practical information for researchers and graduate students who want to review the current situation, to upgrade, and to bring in a new idea to the conventional gasification technologies.

Download or read book A Development Perspective For Biomass Fuelled Electricity Generation Technologies written by Roland Vincent Siemons and published by Clean Fuels b.v.. This book was released on 2002 with total page 297 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Biomass Gasification and Pyrolysis written by Prabir Basu and published by Academic Press. This book was released on 2010-07-19 with total page 377 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book offers comprehensive coverage of the design, analysis, and operational aspects of biomass gasification, the key technology enabling the production of biofuels from all viable sources--some examples being sugar cane and switchgrass. This versatile resource not only explains the basic principles of energy conversion systems, but also provides valuable insight into the design of biomass gasifiers. The author provides many worked out design problems, step-by-step design procedures and real data on commercially operating systems. After fossil fuels, biomass is the most widely used fuel in the world. Biomass resources show a considerable potential in the long term if residues are properly handled and dedicated energy crops are grown. Includes step-by-step design procedures and case studies for Biomass GasificationProvides worked process flow diagrams for gasifier design. Covers integration with other technologies (e.g. gas turbine, engine, fuel cells)

Download or read book Biomass Integrated gasification gas Turbine Power Generation in Zimbabwe written by Wendy Elizabeth Mary Hughes and published by . This book was released on 1998 with total page 668 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Gasification written by Christopher Higman and published by Elsevier. This book was released on 2003-10-21 with total page 403 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides an excellent overview of current technologies for the gasification of coal, oil, gas, biomass and waste feedstocks. Starting from the basic theory, it reviews the potential feedstocks and their suitability for different types of gasification process. Commercial and near-commercial processes are described individually and various features discussed in detail. There is a comprehensive review of contaminants in synthesis gas as well as of gas treating processes. One chapter is devoted to discussions of various chemical, fuel and power applications for gasification. Economic, environmental and safety issues of gasification are also covered. Both authors have been involved with gasification for over 30 years, gaining in the process a fund of practical insight and experience, which is evident throughout the book. * Addresses practical issues such as selection of the best equipment. * Ideal reference for anyone involved in operating or designing a gasification plant.* Written in an easy-to-understand format with worked examples and a comprehensive glossary and bibliography.

Download or read book The Power of Renewables written by Chinese Academy of Engineering and published by National Academies Press. This book was released on 2011-01-29 with total page 256 pages. Available in PDF, EPUB and Kindle. Book excerpt: The United States and China are the world's top two energy consumers and, as of 2010, the two largest economies. Consequently, they have a decisive role to play in the world's clean energy future. Both countries are also motivated by related goals, namely diversified energy portfolios, job creation, energy security, and pollution reduction, making renewable energy development an important strategy with wide-ranging implications. Given the size of their energy markets, any substantial progress the two countries make in advancing use of renewable energy will provide global benefits, in terms of enhanced technological understanding, reduced costs through expanded deployment, and reduced greenhouse gas (GHG) emissions relative to conventional generation from fossil fuels. Within this context, the U.S. National Academies, in collaboration with the Chinese Academy of Sciences (CAS) and Chinese Academy of Engineering (CAE), reviewed renewable energy development and deployment in the two countries, to highlight prospects for collaboration across the research to deployment chain and to suggest strategies which would promote more rapid and economical attainment of renewable energy goals. Main findings and concerning renewable resource assessments, technology development, environmental impacts, market infrastructure, among others, are presented. Specific recommendations have been limited to those judged to be most likely to accelerate the pace of deployment, increase cost-competitiveness, or shape the future market for renewable energy. The recommendations presented here are also pragmatic and achievable.

Download or read book Renewable Hydrogen Production written by Ibrahim Dincer and published by Elsevier. This book was released on 2021-11-27 with total page 384 pages. Available in PDF, EPUB and Kindle. Book excerpt: Renewable Hydrogen Production provides a comprehensive analysis of renewable energy-based hydrogen production. Through simulation analysis and experimental investigations, the book provides fundamentals, compares existing hydrogen production applications, discusses novel technologies, and offers insights into the future directions of this rapidly evolving industry. This all-in-one resource on how to produce clean hydrogen production to enhance energy efficiency and support sustainable development will appeal to a wide variety of industries and professionals. Addresses the production of clean hydrogen from the major sources of renewable energy, including wind, solar, geothermal, hydro, biomass and marine energy Presents information from simulations and experimental analyses Offers insights into the future of renewable hydrogen production

Download or read book Biomass Integrated gasification gas Turbine Power Generation in Zimbabwe written by and published by . This book was released on 1993 with total page 334 pages. Available in PDF, EPUB and Kindle. Book excerpt: