Download or read book Bendable X ray Optics at the ALS written by and published by . This book was released on 2008 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: We review the development at the Advanced Light Source (ALS) of bendable x-ray optics widely used for focusing of beams of soft and hard x-rays. Typically, the focusing is divided in the tangential and sagittal directions into two elliptically cylindrical reflecting elements, the so-called Kirkpatrick-Baez (KB) pair [1]. Because fabrication of elliptical surfaces is complicated, the cost of directly fabricated tangential elliptical cylinders is often prohibitive. This is in contrast to flat optics, that are simpler to manufacture and easier to measure by conventional interferometry. The figure of a flat substrate can be changed by placing torques (couples) at each end. Equal couples form a tangential cylinder, and unequal couples can approximate a tangential ellipse or parabola. We review the nature of the bending, requirements and approaches to the mechanical design, and describe a technique developed at the ALS Optical Metrology Laboratory (OML) for optimal tuning of bendable mirrors before installation in the beamline [2]. The tuning technique adapts a method previously used to adjust bendable mirrors on synchrotron radiation beamlines [3]. However, in our case, optimal tuning of a bendable mirror is based on surface slope trace data obtained with a slope measuring instrument--in our case, the long trace profiler (LTP). We show that due to the near linearity of the bending problem, the minimal set of data, necessary for tuning of two benders, consists of only three slope traces measured before and after a single adjustment of each bending couple. We provide an algorithm that was used in dedicated software for finding optimal settings for the mirror benders. The algorithm is based on the method of regression analysis with experimentally found characteristic functions of the benders. The resulting approximation to the functional dependence of the desired slope shape provides nearly final settings for the benders. Moreover, the characteristic functions of the benders found in the course of tuning, can be used for retuning of the optics to a new desired shape without removing it from the beamline and re-measuring with the LTP. The result of practical use of the developed technique to precisely tune a KB mirror used at the ALS for micro-focusing is also presented. We also describe a simple ray trace using the profiler data which shows expected performance in the beamline and compare the simulation with experimental data. In summary, we also discuss the next steps in the systematic improvement of optical performance for the application of KB pairs in synchrotron beamlines at the ALS.
Download or read book Bendable Focusing X Ray Optics for the ALS and the LCLS written by and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: We review the recent development of bendable x-ray optics used for focusing of beams of soft and hard x-rays at the Advanced Light Source (ALS) at Lawrence Berkeley National Laboratory and at the Linac Coherent Light Source (LCLS) x-ray free electron laser (FEL) at the Stanford Linear Accelerator Center (SLAC) National Accelerator Laboratory. For simultaneous focusing in the tangential and sagittal directions, two elliptically cylindrical reflecting elements, a Kirkpatrick-Baez (KB) pair, are used. Because fabrication of elliptical surfaces is complicated, the cost of directly fabricated tangential elliptical cylinders is often prohibitive. Moreover, such optics cannot be easily readjusted for use in multiple, different experimental arrangements, e.g. at different focal distances. This is in contrast to flat optics that are simpler to manufacture and easier to measure by conventional interferometry. The tangential figure of a flat substrate is changed by placing torques (couples) at each end. Depending on the applied couples, one can tune the shape close to a desired tangential cylinder, ellipse or parabola. We review the nature of the bending, requirements and approaches to the mechanical design, describe original optical and at-wavelength techniques for optimal tuning of bendable optics and alignment on the beamline, and provide beamline performance of the bendable optics used for sub-micro and nano focusing of soft x-rays.
Download or read book At wavelength and Optical Metrology of Bendable X ray Optics for Nanofocusing at the ALS written by and published by . This book was released on 2009 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: We report on a new research and development program at the Advanced Light Source, Lawrence Berkeley National Lab directed to establish both at-wavelength and conventional optical metrology techniques suitable to characterize the surface profile of super-high-quality x-ray optics with sub-microradian precision.
Download or read book Development of At wavelength Metrology for X ray Optics at the ALS written by and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The comprehensive realization of the exciting advantages of new third- and forth-generation synchrotron radiation light sources requires concomitant development of reflecting and diffractive x-ray optics capable of micro- and nano-focusing, brightness preservation, and super high resolution. The fabrication, tuning, and alignment of the optics are impossible without adequate metrology instrumentation, methods, and techniques. While the accuracy of ex situ optical metrology at the Advanced Light Source (ALS) has reached a state-of-the-art level, wavefront control on beamlines is often limited by environmental and systematic alignment factors, and inadequate in situ feedback. At ALS beamline 5.3.1, we are developing broadly applicable, high-accuracy, in situ, at-wavelength wavefront measurement techniques to surpass 100-nrad slope measurement accuracy for Kirkpatrick-Baez (KB) mirrors. The at-wavelength methodology we are developing relies on a series of tests with increasing accuracy and sensitivity. Geometric Hartmann tests, performed with a scanning illuminated sub-aperture determine the wavefront slope across the full mirror aperture. Shearing interferometry techniques use coherent illumination and provide higher sensitivity wavefront measurements. Combining these techniques with high precision optical metrology and experimental methods will enable us to provide in situ setting and alignment of bendable x-ray optics to realize diffraction-limited, sub 50 nm focusing at beamlines. We describe here details of the metrology beamline endstation, the x-ray beam diagnostic system, and original experimental techniques that have already allowed us to precisely set a bendable KB mirror to achieve a focused spot size of 150 nm.
Download or read book X Rays and Extreme Ultraviolet Radiation written by David Attwood and published by Cambridge University Press. This book was released on 2016 with total page 655 pages. Available in PDF, EPUB and Kindle. Book excerpt: Master the physics and understand the current applications of modern X-ray and EUV sources with this fully updated second edition.
Download or read book X Ray Optics and Microanalysis 1992 Proceedings of the 13th INT Conference 31 August 4 September 1992 Manchester UK written by P.B. Kenway and published by CRC Press. This book was released on 2020-10-08 with total page 684 pages. Available in PDF, EPUB and Kindle. Book excerpt: The first ICXOM congress held in Cambridge was the brain-child of Dr. Ellis Cosslett, founder of the Electron Optics Section of the Cavendish Laboratory. Dr. Cosslett pioneered research in x-ray optics and microanalysis and retained a close interest in all subject applications for this area of research, including physics, materials science, chemistry, and biology. X-Ray Optics and Microanalysis 1992 was held in his memory. At a special symposium, friends and colleagues reviewed the present status of research in x-ray optics and microanalysis. S.J. Pennycook of Oak Ridge National Laboratory, D.B. Williams of Lehigh University, J.A. Venables et al. of Arizona State University and Sussex University, and C. Jacobsen et al. of SUNY, Stony Brook are among the researchers whose papers are included in this volume.
Download or read book User Facilities of the Office of Basic Energy Sciences written by and published by . This book was released on 2009 with total page 72 pages. Available in PDF, EPUB and Kindle. Book excerpt: "This brochure overviews the scientific infrastructure that is constructed, maintained, and operated at Department of Energy laboratories for the pursuit of energy-related research." -- cf p. 4
Download or read book Comprehensive Biophysics written by and published by Academic Press. This book was released on 2012-04-12 with total page 3533 pages. Available in PDF, EPUB and Kindle. Book excerpt: Biophysics is a rapidly-evolving interdisciplinary science that applies theories and methods of the physical sciences to questions of biology. Biophysics encompasses many disciplines, including physics, chemistry, mathematics, biology, biochemistry, medicine, pharmacology, physiology, and neuroscience, and it is essential that scientists working in these varied fields are able to understand each other's research. Comprehensive Biophysics, Nine Volume Set will help bridge that communication gap. Written by a team of researchers at the forefront of their respective fields, under the guidance of Chief Editor Edward Egelman, Comprehensive Biophysics, Nine Volume Set provides definitive introductions to a broad array of topics, uniting different areas of biophysics research - from the physical techniques for studying macromolecular structure to protein folding, muscle and molecular motors, cell biophysics, bioenergetics and more. The result is this comprehensive scientific resource - a valuable tool both for helping researchers come to grips quickly with material from related biophysics fields outside their areas of expertise, and for reinforcing their existing knowledge. Biophysical research today encompasses many areas of biology. These studies do not necessarily share a unique identifying factor. This work unites the different areas of research and allows users, regardless of their background, to navigate through the most essential concepts with ease, saving them time and vastly improving their understanding The field of biophysics counts several journals that are directly and indirectly concerned with the field. There is no reference work that encompasses the entire field and unites the different areas of research through deep foundational reviews. Comprehensive Biophysics fills this vacuum, being a definitive work on biophysics. It will help users apply context to the diverse journal literature offering, and aid them in identifying areas for further research Chief Editor Edward Egelman (E-I-C, Biophysical Journal) has assembled an impressive, world-class team of Volume Editors and Contributing Authors. Each chapter has been painstakingly reviewed and checked for consistent high quality. The result is an authoritative overview which ties the literature together and provides the user with a reliable background information and citation resource
Download or read book Performance Optimization of a Bendable Parabolic Cylinder Collimating X ray Mirror for the ALS Micro XAS Beamline 10 3 2 written by and published by . This book was released on 2015 with total page 9 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Advanced Light Source (ALS) beamline (BL) 10.3.2 is an apparatus for X-ray microprobe spectroscopy and diffraction experiments, operating in the energy range 2.4-17 keV. The performance of the beamline, namely the spatial and energy resolutions of the measurements, depends significantly on the collimation quality of light incident on the monochromator. In the BL 10.3.2 end-station, the synchrotron source is imaged 1:1 onto a set of roll slits which form a virtual source. The light from this source is collimated in the vertical direction by a bendable parabolic cylinder mirror. Details are presented of the mirror design, which allows for precision assembly, alignment and shaping of the mirror, as well as for extending of the mirror operating lifetime by a factor of ~10. Assembly, mirror optimal shaping and preliminary alignment were performed ex situ in the ALS X-ray Optics Laboratory (XROL). Using an original method for optimal ex situ characterization and setting of bendable X-ray optics developed at the XROL, a root-mean-square (RMS) residual surface slope error of 0.31 μrad with respect to the desired parabola, and an RMS residual height error of less than 3 nm were achieved. Once in place at the beamline, deviations from the designed optical geometry (e.g. due to the tolerances for setting the distance to the virtual source, the grazing incidence angle, the transverse position) and/or mirror shape (e.g. due to a heat load deformation) may appear. Due to the errors, on installation the energy spread from the monochromator is typically a few electron-volts. Here, a new technique developed and successfully implemented for at-wavelength (in situ) fine optimal tuning of the mirror, enabling us to reduce the collimation-induced energy spread to ~0.05 eV, is described.
Download or read book At wavelength Optical Metrology Development at the ALS written by and published by . This book was released on 2010 with total page 13 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nano-focusing and brightness preservation for ever brighter synchrotron radiation and free electron laser beamlines require surface slope tolerances of x-ray optics on the order of 100 nrad. While the accuracy of fabrication and ex situ metrology of x-ray mirrors has improved over time, beamline in situ performance of the optics is often limited by application specific factors such as x-ray beam heat loading, temperature drift, alignment, vibration, etc. In the present work, we discuss the recent results from the Advanced Light Source developing high accuracy, in situ, at-wavelength wavefront measurement techniques to surpass 100-nrad accuracy surface slope measurements with reflecting x-ray optics. The techniques will ultimately allow closed-loop feedback systems to be implemented for x-ray nano-focusing. In addition, we present a dedicated metrology beamline endstation, applicable to a wide range of in situ metrology and test experiments. The design and performance of a bendable Kirkpatrick-Baez (KB) mirror with active temperature stabilization will also be presented. The mirror is currently used to study, refine, and optimize in situ mirror alignment, bending and metrology methods essential for nano-focusing application.
Download or read book Grazing Incidence and Multilayer X ray Optical Systems written by Richard B. Hoover and published by SPIE-International Society for Optical Engineering. This book was released on 1997 with total page 562 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book X Ray Microscopy II written by David Sayre and published by Springer. This book was released on 2013-06-05 with total page 464 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume is based on papers presented at the International Symposium on X-Ray Microscopy held at Brookhaven National Laboratory, Upton NY, August 31-September 4, 1987. Previous recent symposia on the sub ject were held in New York in 1979, Gottingen in 1983 and Taipei in 1986. Developments in x-ray microscopy continue at a rapid pace, with im portant advances in all major areas: x-ray sources, optics and components, and microscopes and imaging systems. Taken as a whole, the work pre sented here emphasizes three major directions: (a) improvements in the capability and image-quality of x-ray microscopy, expressed principally in systems attached to large, high-brightness x-ray sources; (b) greater access to x-ray microscopy, expressed chiefly in systems employing small, often pulsed, x-ray sources; and (c) increased rate of exploration of applications of x-ray microscopy. The number of papers presented at the symposium has roughly dou bled compared with that of its predecessors. While we are delighted at this growth as a manifestation of vitality and rapid growth of the field, we did have to ask the authors to limit the length of their papers and to submit them in camera-ready form. We thank the authors for their con tributions and for their efforts in adhering to the guidelines on manuscript preparation.
Download or read book X Rays in Nanoscience written by Jinghua Guo and published by John Wiley & Sons. This book was released on 2011-09-22 with total page 279 pages. Available in PDF, EPUB and Kindle. Book excerpt: An up-to-date overview of the different x-ray based methods in the hot fields of nanoscience and nanotechnology, including methods for imaging nanomaterials, as well as for probing the electronic structure of nanostructured materials in order to investigate their different properties. Written by authors at one of the world's top facilities working with these methods, this monograph presents and discusses techniques and applications in the fields of x-ray scattering, spectroscopy and microscope imaging. The resulting systematic collection of these advanced tools will benefit graduate students, postdocs as well as professional researchers.
Download or read book Probing Crystal Plasticity at the Nanoscales written by Arief Suriadi Budiman and published by Springer. This book was released on 2014-12-27 with total page 182 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Brief highlights the search for strain gradients and geometrically necessary dislocations as a possible source of strength for two cases of deformation of materials at small scales: nanoindented single crystal copper and uniaxially compressed single crystal submicron gold pillars. When crystalline materials are mechanically deformed in small volumes, higher stresses are needed for plastic flow. This has been called the "Smaller is Stronger" phenomenon and has been widely observed. studies suggest that plasticity in one case is indeed controlled by the GNDs (strain gradient hardening), whereas in the other, plasticity is not controlled by strain gradients or sub-structure hardening, but rather by dislocation source starvation, wherein smaller volumes are stronger because fewer sources of dislocations are available (dislocation starvation hardening).
Download or read book Atomic And Molecular Physics Proceedings Of The 3rd Us mexico Symposium written by C Cisneros and published by World Scientific. This book was released on 1991-12-31 with total page 514 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Third US/Mexico Symposium on Atomic and Molecular Physics brought together forty-five leading investigators in many fields. Both theory and experiment were well represented. The papers in this volume are based on the participants' invited talks at the symposium and represent an important collection reviewing the most up-to-date work in the different fields. The diversity of research areas represented, coupled to a common local point, revealed different perspectives on such questions as: How do particles depend on one another? Correlation provides a good starting point, but are there other useful conceptual approaches which will yield a new view of the phenomena and a more complete understanding?The contributions in this volume provide different perspectives and bring together a collection of papers which serve as a basis for further progress in this field.
Download or read book Accelerator X Ray Sources written by Richard Talman and published by John Wiley & Sons. This book was released on 2007-02-27 with total page 494 pages. Available in PDF, EPUB and Kindle. Book excerpt: This first book to cover in-depth the generation of x-rays in particle accelerators focuses on electron beams produced by means of the novel Energy Recovery Linac (ERL) technology. The resulting highly brilliant x-rays are at the centre of this monograph, which continues where other books on the market stop. Written primarily for general, high energy and radiation physicists, the systematic treatment adopted by the work makes it equally suitable as an advanced textbook for young researchers.
Download or read book Innovative micro NMR MRI functionality utilizing flexible electronics and control systems written by Nassar, Omar and published by KIT Scientific Publishing. This book was released on 2023-08-15 with total page 278 pages. Available in PDF, EPUB and Kindle. Book excerpt: The advantages offered by the flexible electronics and control systems technologies were utilized for tackling the challenges facing two crucial Magnetic Resonance (MR) applications. The first application is in the field of interventional Magnetic Resonance Imaging (MRI), and the other application is in the field of Nuclear Magnetic Resonance spectroscopy (NMR).
