Download or read book Bench Scale Process for Low Cost CO2 Capture Using a Phase Changing Absorbent written by and published by . This book was released on 2016 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: GE Global Research was contracted by the Department of Energy to design and build a bench-scale process for a novel phase-changing aminosilicone-based CO2 capture solvent (award number DEFE0013687). As part of this program, a technology EH & S assessment (Subtask 5.1) has been completed for a CO2 capture system for a 550 MW coal-fired power plant. The assessment focuses on two chemicals used in the process, the aminosilicone solvent, GAP-0, and dodecylbenzenesulfonic acid (DDBSA), the GAP-0 carbamate formed upon reaction of the GAP-0 with CO2, and two potential byproducts formed in the process, GAP-0/SOx salts and amine-terminated, urea-containing silicone (also referred to as "ureas" in this report). The EH & S assessment identifies and estimates the magnitude of the potential air and water emissions and solid waste generated by the process and reviews the toxicological profiles of the chemicals associated with the process. Details regarding regulatory requirements, engineering controls, and storage and handling procedures are also provided in the following sections.
Download or read book Bench Scale Process for Low Cost Carbon Dioxide CO2 Capture Using a Phase Changing Absorbent written by and published by . This book was released on 2015 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The objective of this project is to design and build a bench-scale process for a novel phase-changing aminosilicone-based CO2-capture solvent. The project will establish scalability and technical and economic feasibility of using a phase-changing CO2-capture absorbent for post-combustion capture of CO2 from coal-fired power plants with 90% capture efficiency and 95% CO2 purity at a cost of $40/tonne of CO2 captured by 2025 and a cost of
Download or read book Proceedings of the 2023 9th International Conference on Advances in Energy Resources and Environment Engineering ICAESEE 2023 written by Abd El-Fatah Abomohra and published by Springer Nature. This book was released on 2024 with total page 890 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Bench Scale Silicone Process for Low Cost CO sub 2 Capture written by and published by . This book was released on 2012 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: This report presents system and economic analysis for a carbon capture unit which uses an amino-silicone solvent for CO2 capture and sequestration (CCS) in a pulverized coal (PC) boiler. The amino-silicone solvent is based on GAP-1 with Tri-Ethylene Glycol (TEG) as a co-solvent. The report also shows results for a CCS unit based on a conventional approach using mono-ethanol amine (MEA). Models were developed for both processes and used to calculate mass and energy balances. Capital costs and energy penalty were calculated for both systems, as well as the increase in cost of electricity. The amino-silicone solvent based system demonstrates significant advantages compared to the MEA system.
Download or read book Negative Emissions Technologies and Reliable Sequestration written by National Academies of Sciences, Engineering, and Medicine and published by National Academies Press. This book was released on 2019-04-08 with total page 511 pages. Available in PDF, EPUB and Kindle. Book excerpt: To achieve goals for climate and economic growth, "negative emissions technologies" (NETs) that remove and sequester carbon dioxide from the air will need to play a significant role in mitigating climate change. Unlike carbon capture and storage technologies that remove carbon dioxide emissions directly from large point sources such as coal power plants, NETs remove carbon dioxide directly from the atmosphere or enhance natural carbon sinks. Storing the carbon dioxide from NETs has the same impact on the atmosphere and climate as simultaneously preventing an equal amount of carbon dioxide from being emitted. Recent analyses found that deploying NETs may be less expensive and less disruptive than reducing some emissions, such as a substantial portion of agricultural and land-use emissions and some transportation emissions. In 2015, the National Academies published Climate Intervention: Carbon Dioxide Removal and Reliable Sequestration, which described and initially assessed NETs and sequestration technologies. This report acknowledged the relative paucity of research on NETs and recommended development of a research agenda that covers all aspects of NETs from fundamental science to full-scale deployment. To address this need, Negative Emissions Technologies and Reliable Sequestration: A Research Agenda assesses the benefits, risks, and "sustainable scale potential" for NETs and sequestration. This report also defines the essential components of a research and development program, including its estimated costs and potential impact.
Download or read book Process Intensification written by David Reay and published by Butterworth-Heinemann. This book was released on 2013-06-05 with total page 624 pages. Available in PDF, EPUB and Kindle. Book excerpt: Process Intensification: Engineering for Efficiency, Sustainability and Flexibility is the first book to provide a practical working guide to understanding process intensification (PI) and developing successful PI solutions and applications in chemical process, civil, environmental, energy, pharmaceutical, biological, and biochemical systems. Process intensification is a chemical and process design approach that leads to substantially smaller, cleaner, safer, and more energy efficient process technology. It improves process flexibility, product quality, speed to market and inherent safety, with a reduced environmental footprint. This book represents a valuable resource for engineers working with leading-edge process technologies, and those involved research and development of chemical, process, environmental, pharmaceutical, and bioscience systems. - No other reference covers both the technology and application of PI, addressing fundamentals, industry applications, and including a development and implementation guide - Covers hot and high growth topics, including emission prevention, sustainable design, and pinch analysis - World-class authors: Colin Ramshaw pioneered PI at ICI and is widely credited as the father of the technology
Download or read book Advanced CO2 Capture Technologies written by Shin-ichi Nakao and published by Springer. This book was released on 2019-05-07 with total page 90 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book summarises the advanced CO2 capture technologies that can be used to reduce greenhouse gas emissions, especially those from large-scale sources, such as power-generation and steel-making plants. Focusing on the fundamental chemistry and chemical processes, as well as advanced technologies, including absorption and adsorption, it also discusses other aspects of the major CO2 capture methods: membrane separation; the basic chemistry and process for CO2 capture; the development of materials and processes; and practical applications, based on the authors’ R&D experience. This book serves as a valuable reference resource for researchers, teachers and students interested in CO2 problems, providing essential information on how to capture CO2 from various types of gases efficiently. It is also of interest to practitioners and academics, as it discusses the performance of the latest technologies applied in large-scale emission sources.
Download or read book Energy Efficient Solvents for CO2 Capture by Gas Liquid Absorption written by Wojciech M. Budzianowski and published by Springer. This book was released on 2016-12-01 with total page 282 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book reviews and characterises promising single-compound solvents, solvent blends and advanced solvent systems suitable for CO2 capture applications using gas-liquid absorption. Focusing on energy efficient solvents with minimal adverse environmental impact, the contributions included analyse the major technological advantages, as well as research and development challenges of promising solvents and solvent systems in various sustainable CO2 capture applications. It provides a valuable source of information for undergraduate and postgraduate students, as well as for chemical engineers and energy specialists.
Download or read book Absorber Modeling and Design in Amine Scrubbing for Carbon Capture written by Tianyu Gao and published by . This book was released on 2021 with total page 400 pages. Available in PDF, EPUB and Kindle. Book excerpt: Absorber design is associated with the most important trade-off between capital and operating cost for CO2 capture by amine scrubbing process. A rate-based absorber model using aqueous piperazine (PZ) has been developed prior to this work. The model is built from bench-scale or small pilot-scale experiments using "bottom-up" strategies and can be improved by larger scale pilot plant experiments. Three pilot plant campaigns were designed and conducted in this work for model validation and improvement. By identifying the systematic bias of solvent equilibrium and applying one adjustable parameter on PZ concentration (8% for NCCC 2019 and SRP 2018, 3% for NCCC 2018), the model can predict the absorber number of transfer units (NTU) and temperature profile with good accuracy. The packing performance model was also validated using experiments running with less packing area that are away from mass transfer pinch. With pilot plant experiments and process modeling, the absorber design using pump-around absorber with hot flue gas inlet was demonstrated as a superior configuration for flue gas with 4% CO2. The pump-around increases the liquid flow and provides effective cooling to the absorber. This configuration was used to design the first-of-its-kind commercial scale absorber in west Texas. The design requires only 25 ft packing, eliminates direct contact cooler and trim cooler to reduce capital cost, and uses 0.2 lean loading, low pump-around temperature (30 °C), and high pump-around rate to improve the performance and to reduce the operating cost. The hybrid and crossflow absorbers were proposed and simulated as an intensification of the pump-around absorber. The hybrid absorber can be as effective as the pump-around absorber but is constrained by intercooling temperature and water balance. The crossflow absorber features small size and high velocity and is favored when the capital cost is relatively high. Achieving higher removal using amine scrubbing was studied using both PZ and MEA solvent, and the optimal CO2 removal was found above 90% (95% for coal and 93% for gas). Zero emission of power plant was feasible using amine scrubbing with an overall cost of 50.4 $/tonne and should be considered before deploying other direct air capture technologies
Download or read book Carbon Capture and Storage written by Mai Bui and published by Royal Society of Chemistry. This book was released on 2019-11-29 with total page 596 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book will provide the latest global perspective on the role and value of carbon capture and storage (CCS) in delivering temperature targets and reducing the impact of global warming. As well as providing a comprehensive, up-to-date overview of the major sources of carbon dioxide emission and negative emissions technologies, the book also discusses technical, economic and political issues associated with CCS along with strategies to enable commercialisation.
Download or read book Advances in Carbon Capture written by Mohammad Reza Rahimpour and published by Woodhead Publishing. This book was released on 2020-08-04 with total page 574 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advances in Carbon Capture reviews major implementations of CO2 capture, including absorption, adsorption, permeation and biological techniques. For each approach, key benefits and drawbacks of separation methods and technologies, perspectives on CO2 reuse and conversion, and pathways for future CO2 capture research are explored in depth. The work presents a comprehensive comparison of capture technologies. In addition, the alternatives for CO2 separation from various feeds are investigated based on process economics, flexibility, industrial aspects, purification level and environmental viewpoints. - Explores key CO2 separation and compare technologies in terms of provable advantages and limitations - Analyzes all critical CO2 capture methods in tandem with related technologies - Introduces a panorama of various applications of CO2 capture
Download or read book Absorption Based Post Combustion Capture of Carbon Dioxide written by Paul Feron and published by Woodhead Publishing. This book was released on 2016-05-27 with total page 816 pages. Available in PDF, EPUB and Kindle. Book excerpt: Absorption-Based Post-Combustion Capture of Carbon Dioxide provides a comprehensive and authoritative review of the use of absorbents for post-combustion capture of carbon dioxide. As fossil fuel-based power generation technologies are likely to remain key in the future, at least in the short- and medium-term, carbon capture and storage will be a critical greenhouse gas reduction technique. Post-combustion capture involves the removal of carbon dioxide from flue gases after fuel combustion, meaning that carbon dioxide can then be compressed and cooled to form a safely transportable liquid that can be stored underground. - Provides researchers in academia and industry with an authoritative overview of the amine-based methods for carbon dioxide capture from flue gases and related processes - Editors and contributors are well known experts in the field - Presents the first book on this specific topic
Download or read book Design of Bench Scale Silicone Process for Low Cost CO sub 2 Capture written by and published by . This book was released on 2012 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The major goal of the project is to design and optimize a bench-scale process for novel silicone CO2-capture solvents and establish scalability and potential for commercialization of post-combustion capture of CO2 from coal-fired power plants. This system should be capable of 90% capture efficiency and demonstrate that less than 35% increase in the cost of energy services can be achieved upon scale-up. Experiments were conducted to obtain data required for design of the major unit operations. The bench-scale system design has been completed, including sizing of major unit operations and the development of a detailed Process and Instrument Diagram (P & ID). The system has been designed to be able to operate over a wide range of process conditions so that the effect of various process variables on performance can be determined. To facilitate flexibility in operation, the absorption column has been designed in a modular manner, so that the height of the column can be varied. The desorber has also been designed to allow for a range of residence times, temperatures, and pressures. The system will be fabricated at Techniserv Inc.
Download or read book Porous Polymer Networks written by Vikas Mittal and published by . This book was released on 2019-01-31 with total page 328 pages. Available in PDF, EPUB and Kindle. Book excerpt: The main aim of the book is to assimilate the fundamental know how about the synthesis, properties as well as applications of a large range of recently developed and commercially viable porous polymer networks.
Download or read book Novel Materials for Carbon Dioxide Mitigation Technology written by Bryan Morreale and published by Elsevier. This book was released on 2015-06-01 with total page 413 pages. Available in PDF, EPUB and Kindle. Book excerpt: Materials for Carbon Dioxide Mitigation Technology offers expert insight and experience from recognized authorities in advanced material development in carbon mitigation technology and constitutes a comprehensive guide to the selection and design of a wide range of solvent/sorbent/catalyst used by scientists globally. It appeals to chemical scientists, material scientists and engineers, energy researchers, and environmental scientists from academia, industry, and government in their research directed toward greener, more efficient carbon mitigation processes. Emphasizes material development for carbon mitigation technologies rather than regulations Provides a fundamental understanding of the underpinning science as well as technological approaches to implement carbon capture, utilization and storage technologies Introduces the driving force behind novel materials, their performance and applications for carbon dioxide mitigation Contains figures, tables and an abundance of examples clearly explaining the development, characterization and evaluation of novel carbon mitigation materials Includes hundreds of citations drawing on the most recent published works on the subject Provides a wealth of real-world examples, illustrating how to bridge nano-scale materials to bulk carbon mitigation properties
Download or read book CO2 Capture with Liquid to Solid Absorbents written by and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: IMPACCT Project: GE and the University of Pittsburgh are developing a unique CO2 capture process in which a liquid absorbent, upon contact with CO2, changes into a solid phase. Once in solid form, the material can be separated and the CO2 can be released for storage by heating. Upon heating, the absorbent returns to its liquid form, where it can be reused to capture more CO2. The approach is more efficient than other solventbased processes because it avoids the heating of extraneous solvents such as water. This ultimately leads to a lower cost of CO2 capture and will lower the additional cost to produce electricity for coal-fired power plants that retrofit their facilities to include this technology.
Download or read book Sustainable Agriculture Reviews 38 written by Inamuddin and published by Springer Nature. This book was released on 2020-01-01 with total page 282 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents materials and physical methods for carbon dioxide sequestration. Materials include nanosponges, titanium oxide/zeolite hybrids, classical absorbents, metal oxides, ionic liquids, alkaline soils and metal organic frameworks. Methods include cryogenic capture, adsorption, solvent dissolution and soil sequestration.
