Download or read book Atomistic Structures of Nano engineered SiC and Radiation induced Amorphization Resistance written by and published by . This book was released on 2015 with total page 5 pages. Available in PDF, EPUB and Kindle. Book excerpt: In this paper, nano-engineered 3C-SiC thin films, which possess columnar structures with high-density stacking faults and twins, were irradiated with 2 MeV Si ions at cryogenic and room temperatures. From cross-sectional transmission electron microscopy observations in combination with Monte Carlo simulations based on the Stopping and Range of Ions in Matter code, it was found that their amorphization resistance is six times greater than bulk crystalline SiC at room temperature. High-angle bright-field images taken by spherical aberration corrected scanning transmission electron microscopy revealed that the distortion of atomic configurations is localized near the stacking faults. Finally, the resultant strain field probably contributes to the enhancement of radiation tolerance of this material.

Download or read book Ion Irradiation induced Microstructural Change in SiC written by Chien-Hung Chen and published by . This book was released on 2015 with total page 117 pages. Available in PDF, EPUB and Kindle. Book excerpt: The high temperature radiation resistance of nuclear materials has become a key issue in developing future nuclear reactors. Because of its mechanical stability under high-energy neutron irradiation and high temperature, silicon carbide (SiC) has great potential as a structural material in advanced nuclear energy systems. A newly developed nano-engineered (NE) 3C SiC with a nano-layered stacking fault (SFs) structure has been recently considered as a prospective choice due to enhanced point defect annihilation between layer-type structures, leading to outstanding radiation durability. The objective of this project was to advance the understanding of gas bubble formation mechanisms under irradiation conditions in SiC. In this work, microstructural evolution induced by helium implantation and ion irradiation was investigated in single crystal and NE SiC. Elastic recoil detection analysis confirmed that the as-implanted helium depth profile did not change under irradiation to 30 dpa at 700 °C. Helium bubbles were found in NE SiC after heavy ion irradiation at a lower temperature than in previous literature results. These results expand the current understanding of helium migration mechanism of NE SiC under high temperature irradiation environment. No obvious bubble growth was observed after ion irradiation at 700 °C, suggesting a long helium bubble incubation process under continued irradiation at this temperature and dose. As determined by electron energy loss spectroscopy measurements, only 1 % of the implanted helium atoms are trapped in bubbles. Helium redistribution and release was observed in the TEM samples under in-situ irradiation at 800 °C. In-situ TEM analysis revealed that the nano-layered SF structure is radiation tolerant below a dose of about 15 dpa at 800 °C, but continued irradiation to 20 dpa under these in-situ conditions leads to loss of the stacking fault structure, which may be a manifestation of irradiating thin TEM foils. The irradiation stability of the SF structure under bulk irradiation remains unknown. This stacking fault structure is critical since it suppresses the formation of dislocation loops normally observed under these irradiation conditions. Systematic studies towards understanding the role of defect migration under irradiation on the evolution of helium bubbles in NE SiC were performed. Keywords SiC, Irradiation, Helium Bubble, TEM/STEM, EELS, In-situ, ERDA

Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1991 with total page 304 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Government Reports Announcements Index written by and published by . This book was released on 1996-09 with total page 1244 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Nanostructure Science and Technology written by Richard W. Siegel and published by Springer Science & Business Media. This book was released on 1999-09-30 with total page 378 pages. Available in PDF, EPUB and Kindle. Book excerpt: Timely information on scientific and engineering developments occurring in laboratories around the world provides critical input to maintaining the economic and technological strength of the United States. Moreover, sharing this information quickly with other countries can greatly enhance the productivity of scientists and engineers. These are some of the reasons why the National Science Foundation (NSF) has been involved in funding science and technology assessments comparing the United States and foreign countries since the early 1980s. A substantial number of these studies have been conducted by the World Technology Evaluation Center (WTEC) managed by Loyola College through a cooperative agreement with NSF. The National Science and Technology Council (NSTC), Committee on Technology's Interagency Working Group on NanoScience, Engineering and Technology (CT/IWGN) worked with WTEC to develop the scope of this Nanostucture Science and Technology report in an effort to develop a baseline of understanding for how to strategically make Federal nanoscale R&D investments in the coming years. The purpose of the NSTC/WTEC activity is to assess R&D efforts in other countries in specific areas of technology, to compare these efforts and their results to U. S. research in the same areas, and to identify opportunities for international collaboration in precompetitive research. Many U. S. organizations support substantial data gathering and analysis efforts focusing on nations such as Japan. But often the results of these studies are not widely available. At the same time, government and privately sponsored studies that are in the public domain tend to be "input" studies.

Download or read book Handbook of Laser Micro and Nano Engineering written by KOJI SUGIOKA. and published by . This book was released on 2019 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: This handbook provides a comprehensive review of the entire field of laser micro and nano processing, including not only a detailed introduction to individual laser processing techniques but also the fundamentals of laser-matter interaction and lasers, optics, equipment, diagnostics, as well as monitoring and measurement techniques for laser processing. Consisting of 11 sections, each composed of 4 to 6 chapters written by leading experts in the relevant field. Each main part of the handbook is supervised by its own part editor(s) so that high-quality content as well as completeness are assured. The book provides essential scientific and technical information to researchers and engineers already working in the field as well as students and young scientists planning to work in the area in the future. Lasers found application in materials processing practically since their invention in 1960, and are currently used widely in manufacturing. The main driving force behind this fact is that the lasers can provide unique solutions in material processing with high quality, high efficiency, high flexibility, high resolution, versatility and low environmental load. Macro-processing based on thermal process using infrared lasers such as CO2 lasers has been the mainstream in the early stages, while research and development of micro- and nano-processing are becoming increasingly more active as short wavelength and/or short pulse width lasers have been developed. In particular, recent advances in ultrafast lasers have opened up a new avenue to laser material processing due to the capabilities of ultrahigh precision micro- and nanofabrication of diverse materials. This handbook is the first book covering the basics, the state-of-the-art and important applications of the dynamic and rapidly expanding discipline of laser micro- and nanoengineering. This comprehensive source makes readers familiar with a broad spectrum of approaches to solve all relevant problems in science and technology. This handbook is the ultimate desk reference for all people working in the field.

Download or read book Mechanochemistry in Nanoscience and Minerals Engineering written by Peter Balaz and published by Springer Science & Business Media. This book was released on 2008-10-20 with total page 422 pages. Available in PDF, EPUB and Kindle. Book excerpt: Mechanochemistry as a branch of solid state chemistry enquires into processes which proceed in solids due to the application of mechanical energy. This provides a thorough, up to date overview of mechanochemistry of solids and minerals. Applications of mechanochemistry in nanoscience with special impact on nanogeoscience are described. Selected advanced identification methods, most frequently applied in nanoscience, are described as well as the advantage of mechanochemical approach in minerals engineering. Examples of industrial applications are given. Mechanochemical technology is being applied in many industrial fields: powder metallurgy (synthesis of nanometals, alloys and nanocompounds), building industry (activation of cements), chemical industry (solid waste treatment, catalyst synthesis, coal ashes utilization), minerals engineering (ore enrichment, enhancement of processes of extractive metallurgy), agriculture industry (solubility increase of fertilizers), and pharmaceutical industry (improvement of solubility and bioavailability of drugs). This reference serves as an introduction to newcomers to mechanochemistry, and encourages more experienced researchers to broaden their knowledge and discover novel applications in the field.

Download or read book Cementitious Materials for Nuclear Waste Immobilization written by Rehab O. Abdel Rahman and published by John Wiley & Sons. This book was released on 2014-11-17 with total page 245 pages. Available in PDF, EPUB and Kindle. Book excerpt: Cementitious materials are an essential part in any radioactive waste disposal facility. Conditioning processes such as cementation are used to convert waste into a stable solid form that is insoluble and will prevent dispersion to the surrounding environment. It is incredibly important to understand the long-term behavior of these materials. This book summarises approaches and current practices in use of cementitious materials for nuclear waste immobilisation. It gives a unique description of the most important aspects of cements as nuclear waste forms: starting with a description of wastes, analyzing the cementitious systems used for immobilization and describing the technologies used, and ending with analysis of cementitious waste forms and their long term behavior in an envisaged disposal environment. Extensive research has been devoted to study the feasibility of using cement or cement based materials in immobilizing and solidifying different radioactive wastes. However, these research results are scattered. This work provides the reader with both the science and technology of the immobilization process, and the cementitious materials used to immobilize nuclear waste. It summarizes current knowledge in the field, and highlights important areas that need more investigation. The chapters include: Introduction, Portland cement, Alternative cements, Cement characterization and testing, Radioactive waste cementation, Waste cementation technology, Cementitious wasteform durability and performance assessment.

Download or read book Ion Solid Interactions written by Michael Nastasi and published by Cambridge University Press. This book was released on 1996-03-29 with total page 572 pages. Available in PDF, EPUB and Kindle. Book excerpt: Comprehensive guide to an important materials science technique for students and researchers.

Download or read book Nanomaterials by Severe Plastic Deformation written by Michael J. Zehetbauer and published by John Wiley & Sons. This book was released on 2006-03-06 with total page 872 pages. Available in PDF, EPUB and Kindle. Book excerpt: These proceedings of the "Second International Conference on Nanomaterials by Severe Plastic Deformation" review the enormous scientific avalanche that has been developing in the field over recent years. A valuable resource for any scientist and engineer working in this emerging field of nanotechnology.

Download or read book Swift Heavy Ions for Materials Engineering and Nanostructuring written by Devesh Kumar Avasthi and published by Springer Science & Business Media. This book was released on 2011-05-24 with total page 292 pages. Available in PDF, EPUB and Kindle. Book excerpt: Ion beams have been used for decades for characterizing and analyzing materials. Now energetic ion beams are providing ways to modify the materials in unprecedented ways. This book highlights the emergence of high-energy swift heavy ions as a tool for tailoring the properties of materials with nanoscale structures. Swift heavy ions interact with materials by exciting/ionizing electrons without directly moving the atoms. This opens a new horizon towards the 'so-called' soft engineering. The book discusses the ion beam technology emerging from the non-equilibrium conditions and emphasizes the power of controlled irradiation to tailor the properties of various types of materials for specific needs.

Download or read book Properties and Applications of Silicon Carbide written by Rosario Gerhardt and published by BoD – Books on Demand. This book was released on 2011-04-04 with total page 550 pages. Available in PDF, EPUB and Kindle. Book excerpt: In this book, we explore an eclectic mix of articles that highlight some new potential applications of SiC and different ways to achieve specific properties. Some articles describe well-established processing methods, while others highlight phase equilibria or machining methods. A resurgence of interest in the structural arena is evident, while new ways to utilize the interesting electromagnetic properties of SiC continue to increase.

Download or read book Radiation Effects in Materials written by Waldemar Alfredo Monteiro and published by BoD – Books on Demand. This book was released on 2016-07-20 with total page 464 pages. Available in PDF, EPUB and Kindle. Book excerpt: The study of radiation effects has developed as a major field of materials science from the beginning, approximately 70 years ago. Its rapid development has been driven by two strong influences. The properties of the crystal defects and the materials containing them may then be studied. The types of radiation that can alter structural materials consist of neutrons, ions, electrons, gamma rays or other electromagnetic waves with different wavelengths. All of these forms of radiation have the capability to displace atoms/molecules from their lattice sites, which is the fundamental process that drives the changes in all materials. The effect of irradiation on materials is fixed in the initial event in which an energetic projectile strikes a target. The book is distributed in four sections: Ionic Materials; Biomaterials; Polymeric Materials and Metallic Materials.

Download or read book Transmission Electron Microscopy written by C. Barry Carter and published by Springer. This book was released on 2016-08-24 with total page 543 pages. Available in PDF, EPUB and Kindle. Book excerpt: This text is a companion volume to Transmission Electron Microscopy: A Textbook for Materials Science by Williams and Carter. The aim is to extend the discussion of certain topics that are either rapidly changing at this time or that would benefit from more detailed discussion than space allowed in the primary text. World-renowned researchers have contributed chapters in their area of expertise, and the editors have carefully prepared these chapters to provide a uniform tone and treatment for this exciting material. The book features an unparalleled collection of color figures showcasing the quality and variety of chemical data that can be obtained from today’s instruments, as well as key pitfalls to avoid. As with the previous TEM text, each chapter contains two sets of questions, one for self assessment and a second more suitable for homework assignments. Throughout the book, the style follows that of Williams & Carter even when the subject matter becomes challenging—the aim is always to make the topic understandable by first-year graduate students and others who are working in the field of Materials Science Topics covered include sources, in-situ experiments, electron diffraction, Digital Micrograph, waves and holography, focal-series reconstruction and direct methods, STEM and tomography, energy-filtered TEM (EFTEM) imaging, and spectrum imaging. The range and depth of material makes this companion volume essential reading for the budding microscopist and a key reference for practicing researchers using these and related techniques.

Download or read book Ceramic Matrix Composites written by Narottam P. Bansal and published by John Wiley & Sons. This book was released on 2014-10-27 with total page 725 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is a comprehensive source of information on various aspects of ceramic matrix composites (CMC). It covers ceramic and carbon fibers; the fiber-matrix interface; processing, properties and industrial applications of various CMC systems; architecture, mechanical behavior at room and elevated temperatures, environmental effects and protective coatings, foreign object damage, modeling, life prediction, integration and joining. Each chapter in the book is written by specialists and internationally renowned researchers in the field. This book will provide state-of-the-art information on different aspects of CMCs. The book will be directed to researchers working in industry, academia, and national laboratories with interest and professional competence on CMCs. The book will also be useful to senior year and graduate students pursuing degrees in ceramic science and engineering, materials science and engineering, aeronautical, mechanical, and civil or aerospace engineering. Presents recent advances, new approaches and discusses new issues in the field, such as foreign object damage, life predictions, multiscale modeling based on probabilistic approaches, etc. Caters to the increasing interest in the application of ceramic matrix composites (CMC) materials in areas as diverse as aerospace, transport, energy, nuclear, and environment. CMCs are considered ans enabling technology for advanced aeropropulsion, space propulsion, space power, aerospace vehicles, space structures, as well as nuclear and chemical industries. Offers detailed descriptions of ceramic and carbon fibers; fiber-matrix interface; processing, properties and industrial applications of various CMC systems; architecture, mechanical behavior at room and elevated temperatures, environmental effects and protective coatings, foreign object damage, modeling, life prediction, integration/joining.

Download or read book Graphene Science Handbook written by Mahmood Aliofkhazraei and published by CRC Press. This book was released on 2016-04-27 with total page 532 pages. Available in PDF, EPUB and Kindle. Book excerpt: An In-Depth Look at the Outstanding Properties of GrapheneThe Graphene Science Handbook is a six-volume set that describes graphene's special structural, electrical, and chemical properties. The book considers how these properties can be used in different applications (including the development of batteries, fuel cells, photovoltaic cells, and supe

Download or read book Silicon Carbide written by Wolfgang J. Choyke and published by Springer Science & Business Media. This book was released on 2013-04-17 with total page 911 pages. Available in PDF, EPUB and Kindle. Book excerpt: Since the 1997 publication of "Silicon Carbide - A Review of Fundamental Questions and Applications to Current Device Technology" edited by Choyke, et al., there has been impressive progress in both the fundamental and developmental aspects of the SiC field. So there is a growing need to update the scientific community on the important events in research and development since then. The editors have again gathered an outstanding team of the world's leading SiC researchers and design engineers to write on the most recent developments in SiC.