Download or read book APS Storage Ring Vacuum Chamber Fabrication written by and published by . This book was released on 1990 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book APS Storage Ring Vacuum Chamber Fabrication written by and published by . This book was released on 1990 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt: The 1104-m circumference Advanced Photon Source Storage Ring Vacuum System is composed of 240 individual sections, which are fabricated from a combination of aluminum extrusions and machined components. The vacuum chambers will have 3800 weld joints, each subject to strict vacuum requirements, as well as a variety of related design criteria. The vacuum criteria and chamber design are reviewed, including a discussion of the weld joint geometries. The critical fabrication process parameters for meeting the design requirements are discussed. The experiences of the prototype chamber fabrication program are presented. Finally, the required facilities preparation for construction activity is briefly described. 6 refs., 6 figs., 1 tab.
Download or read book Vibration Study of the APS Storage Ring Vacuum chamber written by J.A. Jendrzejczyk and published by . This book was released on 1991 with total page 73 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book APS Storage Ring Vacuum Chamber written by and published by . This book was released on 1995 with total page 7 pages. Available in PDF, EPUB and Kindle. Book excerpt: The vacuum characteristics of the APS storage ring vacuum chamber prototype, Section One (S1), is presented. The base pressure achieved was 4 x 10−11, the welds contained no virtual or real leaks, the NeG strip mounting design and activation procedures have been determined, and S1 was found contaminated with hydrocarbons.
Download or read book Vacuum System Development Status for the APS Advanced Photon Source Storage Ring written by and published by . This book was released on 1989 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The status of the design and fabrication of a prototype sector of the storage ring vacuum system for the Advanced Photon Source is described. The 26.5-m-long prototype sector will be assembled within a full-scale magnet and tunnel mockup to study interspacial component relationships for maintenance, as well as the vacuum system operational performance. Each completed vacuum section is mounted as an integral part of the modular structure that contains the magnets and magnet power supplies on a common base. Unique automatic machine welding designs and techniques are employed in the fabrication of the aluminium vacuum chambers from extrusions. Special chamber bending procedures and measurements checks are used to maintain the required flatness of the insider chamber light gap surfaces. Photo-electron yields due to low-energy photons in the narrow channel gap of the vacuum chamber and their potential effects on the overall outgassing rate are found to be negligible. 9 refs., 5 figs.
Download or read book Open Loop Compensation for the Eddy Current Effect in the APS Storage Ring Vacuum Chamber written by and published by . This book was released on 1991 with total page 4 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book APS Storage Ring Vacuum System written by and published by . This book was released on 1990 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book APS Storage Ring Vacuum Chamber Tests for Dimensional Stability After Bakeout Cycling While Under Vacuum written by and published by . This book was released on 1990 with total page 4 pages. Available in PDF, EPUB and Kindle. Book excerpt: Vacuum chamber sections No. 1 and No. 2 were used for these tests. Section No. 1, a short straight section, is representative in these tests of Sections No. 3 and No. 5 as well. Section No. 2 is the longer curved section used within the dipole bend magnets and is representative of the similar Section No. 4. The combination of Sections No. 1 and No. 2 joined by a connected bellows was mounted as presently planned for the final installation. This afforded an early testing of chamber positional stability after bakeout cycling. Tests of chamber dimensional stability were also made during vacuum cycling.
Download or read book Vibration Study of the APS Storage Ring Vacuum chamber written by and published by . This book was released on 1991 with total page 73 pages. Available in PDF, EPUB and Kindle. Book excerpt: The overall objective of this study is to obtain insights into the dynamic coupling between the storage ring vacuum chamber and girder, and an assessment of the potential for unacceptable vibration amplitudes that would require redesign of the vacuum chamber supports. Specific objectives include determination of the vibrational characteristics (natural frequencies and modes) of the coupled vacuum-chamber/girder system, measurement of response amplitudes to forced excitation and ambient floor motion, and calculation of magnification factors associated with the various coupled vibration modes. 1 ref.
Download or read book Vacuum Chamber Thermal Protection for the APS Advanced Photon Source written by and published by . This book was released on 1989 with total page 4 pages. Available in PDF, EPUB and Kindle. Book excerpt: The addition of undulators and wigglers into synchrotron storage rings created new problems in terms of protecting the integrity of the ring vacuum chamber. If the photon beam from these devices were missteered into striking an inadequately cooled section of the storage ring vacuum chamber, the structural strength might be reduced sufficiently that the vacuum envelope could be penetrated, resulting in long downtime of the storage ring. The new generation of high-energy synchrotron light sources will produce photon beams of such high power density that cooling of the vacuum chamber will not prevent a potential penetration of the vacuum envelope, and other methods of preventing this occurrence will be required. Since active methods will be used to ensure that the beams are delivered to beam lines for users during normal operation, there is a need for passive protection methods during non-routine operation, such as turning on new beam lines, injection, etc., when the active systems may be disabled. In addition, the passive methods could prevent the problem from arising and provide the rapid time response necessary for the highest power beams, a property that might not be easily and reliably provided by active methods during the early operation of these machines. This paper summarizes the results of a task group that studied the problem and outlines passive methods of protection for the Advanced Photon Source (APS). 2 refs., 3 figs., 1 tab.
Download or read book Vacuum System Development Status for the APS Storage Ring written by and published by . This book was released on 1989 with total page 4 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book UHV Seal Studies for the Advanced Photon Source Storage Ring Vacuum System written by and published by . This book was released on 1991 with total page 4 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Advanced Photon Source (APS) Storage Ring Vacuum Chambers (SRVC) are constructed of aluminum. The chamber design incorporates aluminum alloy 2219-T87 Conflat flanges welded to an aluminum alloy 6063-T5 extruded chamber body. Vacuum connections to the aluminum Conflat chamber flanges are by means of 304 stainless steel Conflat flanges. To evaluate the Conflat seal assemblies relative to vacuum bake cycles, a Conflat Bake Test Assembly (CBTA) was constructed, and thermal cycling tests were performed between room temperature and 150°C on both stainless steel to aluminum Conflat assemblies and aluminum to aluminum Conflat assemblies. A Helicoflex Bake Test Assembly (HBTA) was similarly constructed to evaluate Helicoflex seals. Both Conflat and Helicoflex seals were studied in a SRVC Sector String Test arrangement of five SRVC sections. The CBTA, HBTA and SRVC tests and their results are reported. 3 refs., 2 figs., 2 tabs.
Download or read book Revised Lattice for the APS Storage Ring written by and published by . This book was released on 1989 with total page 16 pages. Available in PDF, EPUB and Kindle. Book excerpt: As a result of more detailed engineering studies of vacuum chamber components and related accelerator physics studies, the circumference of the APS storage ring is increased by 44 m to a value of 1104 m. The increase is 1.1 m for each of the 40 sectors. The insertion region straight section is lengthened by 0.52 m to 6.72 m. This allows full 20-cm vacuum chamber transition sections leading into and out of the 5.2-m insertion devices. Computer studies using TBCI and MAFIA-T3 have indicated that 20-cm-long transition regions reduce the transverse coupling impedance to an Acceptable low value. The results for 10-cm transition length were marginal.
Download or read book APS Storage Ring Vacuum System Performance written by and published by . This book was released on 1997 with total page 4 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Advanced Photon Source (APS) storage ring was designed to operated with 7-GeV, 100-mA positron beam with lifetimes> 20 hours. The lifetime is limited by residual gas scattering and Touschek scattering at this time. Photon-stimulated desorption and microwave power in the rf cavities are the main gas loads. Comparison of actual system gas loads and design calculations will be given. In addition, several special features of the storage ring vacuum system will be presented.
Download or read book Open Loop Compensation for the Eddy Current Effect in the APS Storage Ring Vacuum Chamber written by and published by . This book was released on 1991 with total page 4 pages. Available in PDF, EPUB and Kindle. Book excerpt: In the third generation synchrotron light sources, closed orbit stabilization against external vibrations is critical to ensure low emittance and high brightness. The Advanced Photon Source (APS) will use a large number (678) of correction magnets to create local bumps and to achieve global orbit stabilization. In this paper, we will present the result of the effort to counter the effect due to the finite inductance of the magnet and the eddy current in the 1/2 in.-thick aluminum storage ring vacuum chamber. The amplitude attenuation and the phase shift of the correction magnet field inside the APS storage ring vacuum chamber were measured. A circuit to compensate for this effect was then inserted between the signal source and the magnet power supply. The amplitude was restored with an error of less than 20% of the source signal amplitude and the phase shift was reduced from 80° to 12° at 10 Hz. Incorporation of this circuit in the closed loop feedback scheme and the resulting beneficial effect in the closed orbit stabilization will be discussed. 4 refs., 4 figs.
Download or read book Advanced Photon Source Experience with Vacuum Chambers for Insertion Devices written by and published by . This book was released on 1997 with total page 4 pages. Available in PDF, EPUB and Kindle. Book excerpt: During the last five years, a new approach to the design and fabrication of extruded aluminum vacuum chambers for insertion devices was developed at the Advanced Photon Source (APS). With this approach, three different versions of the vacuum chamber, with vertical apertures of 12 mm, 8 mm, and 5 mm, were manufactured and tested. Twenty chambers were installed into the APS vacuum system. All have operated with beam, and 16 have been coupled with insertion devices. Two different vacuum chambers with vertical apertures of 16 mm and 11 mm were developed for the BESSY-II storage ring and 3 of 16 mm chambers were manufactured.
