Download or read book Applied Scanning Probe Methods II written by Bharat Bhushan and published by Springer Science & Business Media. This book was released on 2006-06-22 with total page 456 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Nobel Prize of 1986 on Sc- ningTunnelingMicroscopysignaled a new era in imaging. The sc- ning probes emerged as a new - strument for imaging with a p- cision suf?cient to delineate single atoms. At ?rst there were two – the Scanning Tunneling Microscope, or STM, and the Atomic Force Mic- scope, or AFM. The STM relies on electrons tunneling between tip and sample whereas the AFM depends on the force acting on the tip when it was placed near the sample. These were quickly followed by the M- netic Force Microscope, MFM, and the Electrostatic Force Microscope, EFM. The MFM will image a single magnetic bit with features as small as 10nm. With the EFM one can monitor the charge of a single electron. Prof. Paul Hansma at Santa Barbara opened the door even wider when he was able to image biological objects in aqueous environments. At this point the sluice gates were opened and a multitude of different instruments appeared. There are signi?cant differences between the Scanning Probe Microscopes or SPM, and others such as the Scanning Electron Microscope or SEM. The probe microscopes do not require preparation of the sample and they operate in ambient atmosphere, whereas, the SEM must operate in a vacuum environment and the sample must be cross-sectioned to expose the proper surface. However, the SEM can record 3D image and movies, features that are not available with the scanning probes.
Download or read book Applied Scanning Probe Methods II written by Bharat Bhushan and published by Springer. This book was released on 2010-02-12 with total page 420 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Nobel Prize of 1986 on Sc- ningTunnelingMicroscopysignaled a new era in imaging. The sc- ning probes emerged as a new - strument for imaging with a p- cision suf?cient to delineate single atoms. At ?rst there were two – the Scanning Tunneling Microscope, or STM, and the Atomic Force Mic- scope, or AFM. The STM relies on electrons tunneling between tip and sample whereas the AFM depends on the force acting on the tip when it was placed near the sample. These were quickly followed by the M- netic Force Microscope, MFM, and the Electrostatic Force Microscope, EFM. The MFM will image a single magnetic bit with features as small as 10nm. With the EFM one can monitor the charge of a single electron. Prof. Paul Hansma at Santa Barbara opened the door even wider when he was able to image biological objects in aqueous environments. At this point the sluice gates were opened and a multitude of different instruments appeared. There are signi?cant differences between the Scanning Probe Microscopes or SPM, and others such as the Scanning Electron Microscope or SEM. The probe microscopes do not require preparation of the sample and they operate in ambient atmosphere, whereas, the SEM must operate in a vacuum environment and the sample must be cross-sectioned to expose the proper surface. However, the SEM can record 3D image and movies, features that are not available with the scanning probes.
Download or read book Applied Scanning Probe Methods XII written by Bharat Bhushan and published by Springer Science & Business Media. This book was released on 2008-10-24 with total page 271 pages. Available in PDF, EPUB and Kindle. Book excerpt: Crack initiation and growth are key issues when it comes to the mechanical reliab- ity of microelectronic devices and microelectromechanical systems (MEMS). Es- cially in organic electronics where exible substrates will play a major role these issues will become of utmost importance. It is therefore necessary to develop me- ods which in situ allow the experimental investigation of surface deformation and fracture processes in thin layers at a micro and nanometer scale. While scanning electron microscopy (SEM) might be used it is also associated with some major experimental drawbacks. First of all if polymers are investigated they usually have to be coated with a metal layer due to their commonly non-conductive nature. Additi- ally they might be damaged by the electron beam of the microscope or the vacuum might cause outgasing of solvents or evaporation of water and thus change material properties. Furthermore, for all kinds of materials a considerable amount of expe- mental effort is necessary to build a tensile testing machine that ts into the chamber. Therefore, a very promising alternative to SEM is based on the use of an atomic force microscope (AFM) to observe in situ surface deformation processes during straining of a specimen. First steps towards this goal were shown in the 1990s in [1–4] but none of these approaches truly was a microtensile test with sample thicknesses in the range of micrometers. To the authors’ knowledge, this was shown for the rst time by Hild et al. in [5]. 16.
Download or read book Scanning Tunneling Microscopy II written by Roland Wiesendanger and published by Springer Science & Business Media. This book was released on 2013-03-08 with total page 359 pages. Available in PDF, EPUB and Kindle. Book excerpt: Scanning Tunneling Microscopy II, like its predecessor, presents detailed and comprehensive accounts of the basic principles and the broad range of applications of STM and related scanning probe techniques. The applications discussed in this volume come predominantly from the fields of electrochemistry and biology. In contrast to those in STM I, these studies may be performed in air and in liquids. The extensions of the basic technique to map other interactions are described in chapters on scanning force microscopy, magnetic force microscopy, and scanning near-field optical microscopy, together with a survey of other related techniques. Also discussed here is the use of a scanning proximal probe for surface modification. Together, the two volumes give a comprehensive account of experimental aspects of STM and provide essential reading and reference material. In this second edition the text has been updated and new methods are discussed.
Download or read book Applied Scanning Probe Methods X written by Bharat Bhushan and published by Springer Science & Business Media. This book was released on 2007-12-20 with total page 475 pages. Available in PDF, EPUB and Kindle. Book excerpt: The volumes VIII, IX and X examine the physical and technical foundation for recent progress in applied scanning probe techniques. This is the first book to summarize the state-of-the-art of this technique. The field is progressing so fast that there is a need for a set of volumes every 12 to 18 months to capture latest developments. These volumes constitute a timely comprehensive overview of SPM applications.
Download or read book Applied Scanning Probe Methods XI written by Bharat Bhushan and published by Springer Science & Business Media. This book was released on 2008-10-22 with total page 281 pages. Available in PDF, EPUB and Kindle. Book excerpt: The volumes XI, XII and XIII examine the physical and technical foundation for recent progress in applied scanning probe techniques. These volumes constitute a timely comprehensive overview of SPM applications. Real industrial applications are included.
Download or read book Scanning Probe Microscopy and Spectroscopy written by Roland Wiesendanger and published by Cambridge University Press. This book was released on 1994-09-29 with total page 664 pages. Available in PDF, EPUB and Kindle. Book excerpt: The investigation and manipulation of matter on the atomic scale have been revolutionised by scanning tunnelling microscopy and related scanning probe techniques. This book is the first to provide a clear and comprehensive introduction to this subject. Beginning with the theoretical background of scanning tunnelling microscopy, the design and instrumentation of practical STM and associated systems are described in detail, as are the applications of these techniques in fields such as condensed matter physics, chemistry, biology, and nanotechnology. Containing 350 illustrations, and over 1200 references, this unique book represents an ideal introduction to the subject for final-year undergraduates in physics or materials science. It will also be invaluable to graduate students and researchers in any branch of science where scanning probe techniques are used.
Download or read book Scanning Probe Microscopy written by Ernst Meyer and published by Springer Nature. This book was released on 2021-05-31 with total page 330 pages. Available in PDF, EPUB and Kindle. Book excerpt: Written by three leading experts in the field, this textbook describes and explains all aspects of the scanning probe microscopy. Emphasis is placed on the experimental design and procedures required to optimize the performance of the various methods. Scanning Probe Microscopy covers not only the physical principles behind scanning probe microscopy but also questions of instrumental designs, basic features of the different imaging modes, and recurring artifacts. The intention is to provide a general textbook for all types of classes that address scanning probe microscopy. Third year undergraduates and beyond should be able to use it for self-study or as textbook to accompany a course on probe microscopy. Furthermore, it will be valuable as reference book in any scanning probe microscopy laboratory. Novel applications and the latest important results are also presented, and the book closes with a look at the future prospects of scanning probe microscopy, also discussing related techniques in nanoscience. Ideally suited as an introduction for graduate students, the book will also serve as a valuable reference for practising researchers developing and using scanning probe techniques.
Download or read book Scanning Probe Microscopy written by Sergei V. Kalinin and published by Springer Science & Business Media. This book was released on 2007-04-03 with total page 1002 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume will be devoted to the technical aspects of electrical and electromechanical SPM probes and SPM imaging on the limits of resolution, thus providing technical introduction into the field. This volume will also address the fundamental physical phenomena underpinning the imaging mechanism of SPMs.
Download or read book Applied Scanning Probe Methods VIII written by Bharat Bhushan and published by Springer Science & Business Media. This book was released on 2007-12-20 with total page 512 pages. Available in PDF, EPUB and Kindle. Book excerpt: The volumes VIII, IX and X examine the physical and technical foundation for recent progress in applied scanning probe techniques. This is the first book to summarize the state-of-the-art of this technique. The field is progressing so fast that there is a need for a set of volumes every 12 to 18 months to capture latest developments. These volumes constitute a timely comprehensive overview of SPM applications.
Download or read book Applied Scanning Probe Methods XIII written by Bharat Bhushan and published by Springer Science & Business Media. This book was released on 2008-10-29 with total page 284 pages. Available in PDF, EPUB and Kindle. Book excerpt: The volumes XI, XII and XIII examine the physical and technical foundation for recent progress in applied scanning probe techniques. The first volume came out in January 2004, the second to fourth volumes in early 2006 and the fifth to seventh volumes in late 2006. The field is progressing so fast that there is a need for a set of volumes every 12 to 18 months to capture latest developments. These volumes constitute a timely comprehensive overview of SPM applications. After introducing scanning probe microscopy, including sensor technology and tip characterization, chapters on use in various industrial applications are presented. Industrial applications span topographic and dynamical surface studies of thin-film semiconductors, polymers, paper, ceramics, and magnetic and biological materials. The chapters have been written by leading researchers and application scientists from all over the world and from various industries to provide a broader perspective.
Download or read book Applied Scanning Probe Methods IX written by Bharat Bhushan and published by Springer Science & Business Media. This book was released on 2007-12-20 with total page 436 pages. Available in PDF, EPUB and Kindle. Book excerpt: The volumes VIII, IX and X examine the physical and technical foundation for recent progress in applied scanning probe techniques. This is the first book to summarize the state-of-the-art of this technique. The field is progressing so fast that there is a need for a set of volumes every 12 to 18 months to capture latest developments. These volumes constitute a timely and comprehensive overview of SPM applications.
Download or read book Scanning Probe Microscopy in Nanoscience and Nanotechnology 2 written by Bharat Bhushan and published by Springer Science & Business Media. This book was released on 2010-12-17 with total page 823 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the physical and technical foundation of the state of the art in applied scanning probe techniques. It constitutes a timely and comprehensive overview of SPM applications. The chapters in this volume relate to scanning probe microscopy techniques, characterization of various materials and structures and typical industrial applications, including topographic and dynamical surface studies of thin-film semiconductors, polymers, paper, ceramics, and magnetic and biological materials. The chapters are written by leading researchers and application scientists from all over the world and from various industries to provide a broader perspective.
Download or read book Scanning Tunneling Microscopy III written by Roland Wiesendanger and published by Springer Science & Business Media. This book was released on 2013-03-07 with total page 415 pages. Available in PDF, EPUB and Kindle. Book excerpt: Scanning Tunneling Microscopy III provides a unique introduction to the theoretical foundations of scanning tunneling microscopy and related scanning probe methods. The different theoretical concepts developed in the past are outlined, and the implications of the theoretical results for the interpretation of experimental data are discussed in detail. Therefore, this book serves as a most useful guide for experimentalists as well as for theoreticians working in the field of local probe methods. In this second edition the text has been updated and new methods are discussed.
Download or read book Applied Scanning Probe Methods I written by Bharat Bhushan and published by Springer Science & Business Media. This book was released on 2014-02-26 with total page 485 pages. Available in PDF, EPUB and Kindle. Book excerpt: Examining the physical and technical foundation for recent progress with this technique, Applied Scanning Probe Methods offers a timely and comprehensive overview of SPM applications, now that industrial applications span topographic and dynamical surface studies of thin-film semiconductors, polymers, paper, ceramics, and magnetic and biological materials. First it lays the theoretical background of static and dynamic force microscopies, including sensor technology and tip characterization, contributions detail applications such as macro- and nanotribology, polymer surfaces, and roughness investigations. The final part on industrial research addresses special applications of scanning force nanoprobes such as atomic manipulation and surface modification, as well as single electron devices based on SPM.
Download or read book Scanning Probe Microscopy written by Bert Voigtländer and published by Springer. This book was released on 2015-02-24 with total page 375 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book explains the operating principles of atomic force microscopy and scanning tunneling microscopy. The aim of this book is to enable the reader to operate a scanning probe microscope successfully and understand the data obtained with the microscope. The chapters on the scanning probe techniques are complemented by the chapters on fundamentals and important technical aspects. This textbook is primarily aimed at graduate students from physics, materials science, chemistry, nanoscience and engineering, as well as researchers new to the field.
Download or read book Acoustic Scanning Probe Microscopy written by Francesco Marinello and published by Springer Science & Business Media. This book was released on 2012-10-04 with total page 513 pages. Available in PDF, EPUB and Kindle. Book excerpt: The combination of atomic force microscopy with ultrasonic methods allows the nearfield detection of acoustic signals. The nondestructive characterization and nanoscale quantitative mapping of surface adhesion and stiffness or friction is possible. The aim of this book is to provide a comprehensive review of different scanning probe acoustic techniques, including AFAM, UAFM, SNFUH, UFM, SMM and torsional tapping modes. Basic theoretical explanations are given to understand not only the probe dynamics but also the dynamics of tip surface contacts. Calibration and enhancement are discussed to better define the performance of the techniques, which are also compared with other classical techniques such as nanoindentation or surface acoustic wave. Different application fields are described, including biological surfaces, polymers and thin films.
