Download or read book Wind Energy Generation Modelling and Control written by Olimpo Anaya-Lara and published by John Wiley & Sons. This book was released on 2011-08-24 with total page 222 pages. Available in PDF, EPUB and Kindle. Book excerpt: WIND ENERGY GENERATION WIND ENERGY GENERATION MODELLING AND CONTROL With increasing concern over climate change and the security of energy supplies, wind power is emerging as an important source of electrical energy throughout the world. Modern wind turbines use advanced power electronics to provide efficient generator control and to ensure compatible operation with the power system. Wind Energy Generation describes the fundamental principles and modelling of the electrical generator and power electronic systems used in large wind turbines. It also discusses how they interact with the power system and the influence of wind turbines on power system operation and stability. Key features: Includes a comprehensive account of power electronic equipment used in wind turbines and for their grid connection. Describes enabling technologies which facilitate the connection of large-scale onshore and offshore wind farms. Provides detailed modelling and control of wind turbine systems. Shows a number of simulations and case studies which explain the dynamic interaction between wind power and conventional generation.

Download or read book IEEE Recommended Practice for Calculating Short Circuit Currents in Industrial and Commercial Power Systems written by and published by Institute of Electrical & Electronics Engineers(IEEE). This book was released on 2006-01-01 with total page 300 pages. Available in PDF, EPUB and Kindle. Book excerpt: This recommended practice provides short-circuit current information including calculated short-circuit current duties for the application in industrial plants and commercial buildings, at all power system voltages, of power system equipment that senses, carries, or interrupts short-circuit currents.

Download or read book Power Systems Modelling and Fault Analysis written by Nasser Tleis and published by Elsevier. This book was released on 2007-11-30 with total page 650 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a comprehensive practical treatment of the modelling of electrical power systems, and the theory and practice of fault analysis of power systems covering detailed and advanced theories as well as modern industry practices.The continuity and quality of electricity delivered safely and economically by today's and future's electrical power networks are important for both developed and developing economies. The correct modelling of power system equipment and correct fault analysis of electrical networks are pre-requisite to ensuring safety and they play a critical role in the identification of economic network investments. Environmental and economic factors require engineers to maximise the use of existing assets which in turn require accurate modelling and analysis techniques. The technology described in this book will always be required for the safe and economic design and operation of electrical power systems. The book describes relevant advances in industry such as in the areas of international standards developments, emerging new generation technologies such as wind turbine generators, fault current limiters, multi-phase fault analysis, measurement of equipment parameters, probabilistic short-circuit analysis and electrical interference.*A fully up-to-date guide to the analysis and practical troubleshooting of short-circuit faults in electricity utilities and industrial power systems*Covers generators, transformers, substations, overhead power lines and industrial systems with a focus on best-practice techniques, safety issues, power system planning and economics*North American and British / European standards covered

Download or read book Power System Analysis written by J.C. Das and published by CRC Press. This book was released on 2002-04-17 with total page 880 pages. Available in PDF, EPUB and Kindle. Book excerpt: Featuring extensive calculations and examples, this reference discusses theoretical and practical aspects of short-circuit currents in ac and dc systems, load flow, and harmonic analyses to provide a sound knowledge base for modern computer-based studies that can be utilized in real-world applications. Presenting more than 2300 figures, tables, and

Download or read book Computer Aided Power System Analysis written by Ramasamy Natarajan and published by CRC Press. This book was released on 2002-04-03 with total page 394 pages. Available in PDF, EPUB and Kindle. Book excerpt: This title evaluates the performance, safety, efficiency, reliability and economics of a power delivery system. It emphasizes the use and interpretation of computational data to assess system operating limits, load level increases, equipment failure and mitigating procedures through computer-aided analysis to maximize cost-effectiveness.

Download or read book Short circuit Currents written by Jürgen Schlabbach and published by IET. This book was released on 2005-10-17 with total page 336 pages. Available in PDF, EPUB and Kindle. Book excerpt: Short-circuit Currents gives an overview of the components within power systems with respect to the parameters needed for short-circuit current calculation.

Download or read book Short Circuits in Power Systems written by Ismail Kasikci and published by John Wiley & Sons. This book was released on 2018-02-27 with total page 312 pages. Available in PDF, EPUB and Kindle. Book excerpt: Reflecting the changes to the all-important short circuit calculations in three-phase power systems according to IEC 60909-0 standard, this new edition of the practical guide retains its proven and unique concept of explanations, calculations and real-life examples of short circuits in electrical networks. It has also been completely revised and expanded by 20% to include the standard-compliant prevention of short circuits in electrical networks for photovoltaics and wind energy. By understanding the theory any software allows users to perform all the necessary calculations with ease so they can work on the design and application of low- and high-voltage power systems. This book is a practitioner's guide intended for students, electrical engineers, engineers in power technology, the electrotechnical industry, engineering consultants, energy suppliers, chemical engineers and physicists in industry.

Download or read book Power System Dynamics with Computer Based Modeling and Analysis written by Yoshihide Hase and published by John Wiley & Sons. This book was released on 2020-01-21 with total page 1138 pages. Available in PDF, EPUB and Kindle. Book excerpt: A unique combination of theoretical knowledge and practical analysis experience Derived from Yoshihide Hases Handbook of Power Systems Engineering, 2nd Edition, this book provides readers with everything they need to know about power system dynamics. Presented in three parts, it covers power system theories, computation theories, and how prevailed engineering platforms can be utilized for various engineering works. It features many illustrations based on ETAP to help explain the knowledge within as much as possible. Recompiling all the chapters from the previous book, Power System Dynamics with Computer Based Modeling and Analysis offers nineteen new and improved content with updated information and all new topics, including two new chapters on circuit analysis which help engineers with non-electrical engineering backgrounds. Topics covered include: Essentials of Electromagnetism; Complex Number Notation (Symbolic Method) and Laplace-transform; Fault Analysis Based on Symmetrical Components; Synchronous Generators; Induction-motor; Transformer; Breaker; Arrester; Overhead-line; Power cable; Steady-State/Transient/Dynamic Stability; Control governor; AVR; Directional Distance Relay and R-X Diagram; Lightning and Switching Surge Phenomena; Insulation Coordination; Harmonics; Power Electronics Applications (Devices, PE-circuit and Control) and more. Combines computer modeling of power systems, including analysis techniques, from an engineering consultants perspective Uses practical analytical software to help teach how to obtain the relevant data, formulate what-if cases, and convert data analysis into meaningful information Includes mathematical details of power system analysis and power system dynamics Power System Dynamics with Computer-Based Modeling and Analysis will appeal to all power system engineers as well as engineering and electrical engineering students.

Download or read book Short Circuit Withstand Capability of Power Transformers written by Daniel Hermann Geißler and published by . This book was released on 2016-08-15 with total page 174 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Shipboard Electrical Power Systems written by Mukund R. Patel and published by CRC Press. This book was released on 2021-07-18 with total page 428 pages. Available in PDF, EPUB and Kindle. Book excerpt: Presents an expanded range of topics, and new developments in shipboard electrical power Offers solutions for meeting the increasing demand for large, fast, efficient, and reconfigurable ships Utilizes state-of-the-art power systems analysis software to illustrate and solve practical problems Compiles critical information on Power System Design, Analysis, and Operation in a single volume Provides math review sections, worked examples, and numerous chapter problems

Download or read book Analysis of Short Circuit Current Contribution for Wind Turbine Generators written by Prof. Chintan Mehta and published by . This book was released on 2019-02-24 with total page 109 pages. Available in PDF, EPUB and Kindle. Book excerpt: The electrical energy generation is the growth engine of any nation. Till last decade, the electrical power generation was basically produced by thermal energy but due to environmental impacts the focus of electrical energy generation shifts towards renewable energy sources. Out of various renewable sources available for electrical energy generation, the main focus is on wind and solar energy to generate the electrical energy. Penetration of wind energy is increased exponentially, but as compared with conventional energy it is highly intermittent in nature. It is a challenge to synchronize the wind energy in to the conventional power grid. In this thesis, short-circuit current is calculated as per IEC-60909 and it is veried using PSCAD/EMTDC software fora single machine connected to a single load. The standard IEEE 14 Bus system is analyzed using PSCAD/EMTDC. In standard IEEE 14 Bus system, MVA method is used for calculating the short circuit current under 3 phase to ground fault condition and it is veried using PSCAD/EMTDC for all the buses. The single circuit model is introduced to analyze the concept of asymmetrical fault current. The behavior of Synchronous machine, Induction machine and doubly fed induction generator (DFIG) are analyzed under the 3 phase to ground symmetrical fault condition. The short circuit current contribution of DFIG is calculated analytically and the same is validated by PSCAD/EMTDC software under various wind speeds and by considering certain voltage drops of the generator output. The behavior of DFIG and conventional induction generator is analyzed during steady-state and faulty condition under the comparable ratings and parameters. The IEEE 1547 and Indian grid code standard with Low Voltage Ride Through (LVRT) is analyzed or WTGs.

Download or read book Low Power Digital VLSI Design written by Abdellatif Bellaouar and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 539 pages. Available in PDF, EPUB and Kindle. Book excerpt: Low-Power Digital VLSI Design: Circuits and Systems addresses both process technologies and device modeling. Power dissipation in CMOS circuits, several practical circuit examples, and low-power techniques are discussed. Low-voltage issues for digital CMOS and BiCMOS circuits are emphasized. The book also provides an extensive study of advanced CMOS subsystem design. A low-power design methodology is presented with various power minimization techniques at the circuit, logic, architecture and algorithm levels. Features: Low-voltage CMOS device modeling, technology files, design rules Switching activity concept, low-power guidelines to engineering practice Pass-transistor logic families Power dissipation of I/O circuits Multi- and low-VT CMOS logic, static power reduction circuit techniques State of the art design of low-voltage BiCMOS and CMOS circuits Low-power techniques in CMOS SRAMS and DRAMS Low-power on-chip voltage down converter design Numerous advanced CMOS subsystems (e.g. adders, multipliers, data path, memories, regular structures, phase-locked loops) with several design options trading power, delay and area Low-power design methodology, power estimation techniques Power reduction techniques at the logic, architecture and algorithm levels More than 190 circuits explained at the transistor level.

Download or read book IEEE Recommended Practice for Electric Power Distribution for Industrial Plants written by Institute of Electrical and Electronics Engineers and published by Institute of Electrical & Electronics Engineers(IEEE). This book was released on 1994 with total page 776 pages. Available in PDF, EPUB and Kindle. Book excerpt: A thorough analysis of basic electrical-systems considerations is presented. Guidance is provided in design, construction, and continuity of an overall system to achieve safety of life and preservation of property; reliability; simplicity of operation; voltage regulation in the utilization of equipment within the tolerance limits under all load conditions; care and maintenance; and flexibility to permit development and expansion. Recommendations are made regarding system planning; voltage considerations; surge voltage protection; system protective devices; fault calculations; grounding; power switching, transformation, and motor-control apparatus; instruments and meters; cable systems; busways; electrical energy conservation; and cost estimation.

Download or read book Disturbance Analysis for Power Systems written by Mohamed A. Ibrahim and published by John Wiley & Sons. This book was released on 2011-09-28 with total page 736 pages. Available in PDF, EPUB and Kindle. Book excerpt: More than ninety case studies shed new light on power system phenomena and power system disturbances Based on the author's four decades of experience, this book enables readers to implement systems in order to monitor and perform comprehensive analyses of power system disturbances. Most importantly, readers will discover the latest strategies and techniques needed to detect and resolve problems that could lead to blackouts to ensure the smooth operation and reliability of any power system. Logically organized, Disturbance Analysis for Power Systems begins with an introduction to the power system disturbance analysis function and its implementation. The book then guides readers through the causes and modes of clearing of phase and ground faults occurring within power systems as well as power system phenomena and their impact on relay system performance. The next series of chapters presents more than ninety actual case studies that demonstrate how protection systems have performed in detecting and isolating power system disturbances in: Generators Transformers Overhead transmission lines Cable transmission line feeders Circuit breaker failures Throughout these case studies, actual digital fault recording (DFR) records, oscillograms, and numerical relay fault records are presented and analyzed to demonstrate why power system disturbances happen and how the sequence of events are deduced. The final chapter of the book is dedicated to practice problems, encouraging readers to apply what they've learned to perform their own system disturbance analyses. This book makes it possible for engineers, technicians, and power system operators to perform expert power system disturbance analyses using the latest tested and proven methods. Moreover, the book's many cases studies and practice problems make it ideal for students studying power systems.

Download or read book Grid Converters for Photovoltaic and Wind Power Systems written by Remus Teodorescu and published by John Wiley & Sons. This book was released on 2011-07-28 with total page 358 pages. Available in PDF, EPUB and Kindle. Book excerpt: Grid converters are the key player in renewable energy integration. The high penetration of renewable energy systems is calling for new more stringent grid requirements. As a consequence, the grid converters should be able to exhibit advanced functions like: dynamic control of active and reactive power, operation within a wide range of voltage and frequency, voltage ride-through capability, reactive current injection during faults, grid services support. This book explains the topologies, modulation and control of grid converters for both photovoltaic and wind power applications. In addition to power electronics, this book focuses on the specific applications in photovoltaic wind power systems where grid condition is an essential factor. With a review of the most recent grid requirements for photovoltaic and wind power systems, the book discusses these other relevant issues: modern grid inverter topologies for photovoltaic and wind turbines islanding detection methods for photovoltaic systems synchronization techniques based on second order generalized integrators (SOGI) advanced synchronization techniques with robust operation under grid unbalance condition grid filter design and active damping techniques power control under grid fault conditions, considering both positive and negative sequences Grid Converters for Photovoltaic and Wind Power Systems is intended as a coursebook for graduated students with a background in electrical engineering and also for professionals in the evolving renewable energy industry. For people from academia interested in adopting the course, a set of slides is available for download from the website. www.wiley.com/go/grid_converters

Download or read book Advanced Electrical and Electronics Engineering written by Jian Lee and published by Springer Science & Business Media. This book was released on 2011-04-13 with total page 702 pages. Available in PDF, EPUB and Kindle. Book excerpt: 2010 First International Conference on Electrical and Electronics Engineering was held in Wuhan, China December 4-5. Advanced Electrical and Electronics Engineering book contains 72 revised and extended research articles written by prominent researchers participating in the conference. Topics covered include, Power Engineering, Telecommunication, Control engineering, Signal processing, Integrated circuit, Electronic amplifier, Nano-technologies, Circuits and networks, Microelectronics, Analog circuits, Digital circuits, Nonlinear circuits, Mixed-mode circuits, Circuits design, Sensors, CAD tools, DNA computing, Superconductivity circuits. Electrical and Electronics Engineering will offer the state of art of tremendous advances in Electrical and Electronics Engineering and also serve as an excellent reference work for researchers and graduate students working with/on Electrical and Electronics Engineering.

Download or read book Fundamentals of Electrical Design Module 2 PRELIMINARY AND DETAILED DESIGN ANALYSIS written by and published by Integrity Institute of Tech. This book was released on with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt: