Download or read book Analysis and Design of Wideband CMOS Transimpedance Amplifiers Using Inductive Feedback written by Omidreza Ghasemi and published by . This book was released on 2012 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book An Ultra Wide Band CMOS Low Noise Amplifier Design written by Nahusha Bhadravati Mohankumar and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: An RF ultra wide band low noise amplifier designed for the frequency range of 12-18 GHz of operation is presented in this paper. The low noise amplifier is designed using the state-of-the-art complementary metal oxide semiconductor 45 nm technology. Berkeley's Predictive Technology Model (PTM) is used to generate a fairly accurate mathematical model and the SPICE data is implemented into the BSIM 4 version of the Advanced Design Systems (ADS) program. The low noise design strategy is mainly based on the analysis of high frequency CMOS operation. This LNA has two stages: the first stage is a RL feedback amplifier with an inductive load, and the second stage is a RC feedback amplifier with an inductive load. High frequency small signal MOSFET models with shunt-shunt feedback are used to determine the input impedance, output impedance and gain equations governing this circuit. Simulation results of this two stage feedback amplifier demonstrate a gain of 19 dB over a 6 GHz bandwidth, high linearity, and a low noise figure-less than 2.4 dB. This is a low voltage high current amplifier which requires a supply voltage of simply 0.5 V and has low power consumption (~13.5 mW).
Download or read book Analysis and Design of Transimpedance Amplifiers for Optical Receivers written by Eduard Säckinger and published by John Wiley & Sons. This book was released on 2017-09-26 with total page 588 pages. Available in PDF, EPUB and Kindle. Book excerpt: An up-to-date, comprehensive guide for advanced electrical engineering studentsand electrical engineers working in the IC and optical industries This book covers the major transimpedance amplifier (TIA) topologies and their circuit implementations for optical receivers. This includes the shunt-feedback TIA, common-base TIA, common-gate TIA, regulated-cascode TIA, distributed-amplifier TIA, nonresistive feedback TIA, current-mode TIA, burst-mode TIA, and analog-receiver TIA. The noise, transimpedance, and other performance parameters of these circuits are analyzed and optimized. Topics of interest include post amplifiers, differential vs. single-ended TIAs, DC input current control, and adaptive transimpedance. The book features real-world examples of TIA circuits for a variety of receivers (direct detection, coherent, burst-mode, etc.) implemented in a broad array of technologies (HBT, BiCMOS, CMOS, etc.). The book begins with an introduction to optical communication systems, signals, and standards. It then moves on to discussions of optical fiber and photodetectors. This discussion includes p-i-n photodetectors; avalanche photodetectors (APD); optically preamplified detectors; integrated detectors, including detectors for silicon photonics; and detectors for phase-modulated signals, including coherent detectors. This is followed by coverage of the optical receiver at the system level: the relationship between noise, sensitivity, optical signal-to-noise ratio (OSNR), and bit-error rate (BER) is explained; receiver impairments, such as intersymbol interference (ISI), are covered. In addition, the author presents TIA specifications and illustrates them with example values from recent product data sheets. The book also includes: Many numerical examples throughout that help make the material more concrete for readers Real-world product examples that show the performance of actual IC designs Chapter summaries that highlight the key points Problems and their solutions for readers who want to practice and deepen their understanding of the material Appendices that cover communication signals, eye diagrams, timing jitter, nonlinearity, adaptive equalizers, decision point control, forward error correction (FEC), and second-order low-pass transfer functions Analysis and Design of Transimpedance Amplifiers for Optical Receivers belongs on the reference shelves of every electrical engineer working in the IC and optical industries. It also can serve as a textbook for upper-level undergraduates and graduate students studying integrated circuit design and optical communication.
Download or read book Low Noise Wide Band Amplifiers in Bipolar and CMOS Technologies written by Zhong Yuan Chong and published by Springer Science & Business Media. This book was released on 2013-03-09 with total page 219 pages. Available in PDF, EPUB and Kindle. Book excerpt: Analog circuit design has grown in importance because so many circuits cannot be realized with digital techniques. Examples are receiver front-ends, particle detector circuits, etc. Actually, all circuits which require high precision, high speed and low power consumption need analog solutions. High precision also needs low noise. Much has been written already on low noise design and optimization for low noise. Very little is available however if the source is not resistive but capacitive or inductive as is the case with antennas or semiconductor detectors. This book provides design techniques for these types of optimization. This book is thus intended firstly for engineers on senior or graduate level who have already designed their first operational amplifiers and want to go further. It is especially for engineers who do not want just a circuit but the best circuit. Design techniques are given that lead to the best performance within a certain technology. Moreover, this is done for all important technologies such as bipolar, CMOS and BiCMOS. Secondly, this book is intended for engineers who want to understand what they are doing. The design techniques are intended to provide insight. In this way, the design techniques can easily be extended to other circuits as well. Also, the design techniques form a first step towards design automation. Thirdly, this book is intended for analog design engineers who want to become familiar with both bipolar and CMOS technologies and who want to learn more about which transistor to choose in BiCMOS.
Download or read book Highly Linear Integrated Wideband Amplifiers written by Henrik Sjöland and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 171 pages. Available in PDF, EPUB and Kindle. Book excerpt: Highly Linear Integrated Wideband Amplifiers: Design and Analysis Techniques for Frequencies from Audio to RF deals with the complicated issues involved in the design of high-linearity integrated wideband amplifiers for different operating frequencies. The book demonstrates these principles using a number of high-performance designs. New topologies for high linearity are presented, as well as a novel method for estimating the intermodulation distortion of a wideband signal. One of the most exciting results presented is an enhanced feedback configuration called feedback boosting that is capable of very low distortion. Also important is a statistical method for relating the intermodulation distortion of a wideband signal to the total harmonic distortion (THD) of a single tone. The THD, as opposed to the intermodulation distortion of the wideband signal, is easy to measure and use as a design parameter. Three different applications where high linearity is needed are identified, namely audio power amplifiers, wideband IF amplifiers and RF power amplifiers. For these applications high-performance integrated amplifier designs using novel topologies are presented together with measurement results. The audio amplifiers are built in CMOS and are capable of driving 8Omega loudspeaker loads directly without using any external components. One of the designs can operate on a supply voltage down to 1.5V. Both bipolar and CMOS wideband IF amplifiers are built; they are fully differential and have linearity from DC to 20 MHz. Finally, an RF power amplifier is built in CMOS, without using inductors, in order to investigate what performance can be achieved without them. Highly Linear Integrated Wideband Amplifiers: Design and Analysis Techniques for Frequencies from Audio to RF is an excellent reference for researchers and designers of integrated amplifiers, and may be used as a text for advanced courses on the topic.
Download or read book Analysis and Design of CMOS Wide band Low Noise Amplifiers written by Srikanth Arekapudi and published by . This book was released on 2004 with total page 108 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book A Novel Design of Ultra Wideband CMOS Low Noise Amplifier with Wideband Impedance Matching written by Sumit Vishwakarma and published by . This book was released on 2004 with total page 196 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Low power Integrated Silicon Optical Receiver Design for High performance Datalinks written by John Andrew Guckenberger and published by Ann Arbor, Mich. : University Microfilms International. This book was released on 2005 with total page 298 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book CMOS written by R. Jacob Baker and published by John Wiley & Sons. This book was released on 2008 with total page 1074 pages. Available in PDF, EPUB and Kindle. Book excerpt: This edition provides an important contemporary view of a wide range of analog/digital circuit blocks, the BSIM model, data converter architectures, and more. The authors develop design techniques for both long- and short-channel CMOS technologies and then compare the two.
Download or read book Design of Integrated Circuits for Optical Communications written by Behzad Razavi and published by John Wiley & Sons. This book was released on 2012-09-14 with total page 444 pages. Available in PDF, EPUB and Kindle. Book excerpt: The only book on integrated circuits for optical communications that fully covers High-Speed IOs, PLLs, CDRs, and transceiver design including optical communication The increasing demand for high-speed transport of data has revitalized optical communications, leading to extensive work on high-speed device and circuit design. With the proliferation of the Internet and the rise in the speed of microprocessors and memories, the transport of data continues to be the bottleneck, motivating work on faster communication channels. Design of Integrated Circuits for Optical Communications, Second Edition deals with the design of high-speed integrated circuits for optical communication transceivers. Building upon a detailed understanding of optical devices, the book describes the analysis and design of critical building blocks, such as transimpedance and limiting amplifiers, laser drivers, phase-locked loops, oscillators, clock and data recovery circuits, and multiplexers. The Second Edition of this bestselling textbook has been fully updated with: A tutorial treatment of broadband circuits for both students and engineers New and unique information dealing with clock and data recovery circuits and multiplexers A chapter dedicated to burst-mode optical communications A detailed study of new circuit developments for optical transceivers An examination of recent implementations in CMOS technology This text is ideal for senior graduate students and engineers involved in high-speed circuit design for optical communications, as well as the more general field of wireline communications.
Download or read book Broadband Circuits for Optical Fiber Communication written by Eduard Säckinger and published by John Wiley & Sons. This book was released on 2005-05-27 with total page 454 pages. Available in PDF, EPUB and Kindle. Book excerpt: An expert guide to the new and emerging field of broadband circuits for optical fiber communication This exciting publication makes it easy for readers to enter into and deepen their knowledge of the new and emerging field of broadband circuits for optical fiber communication. The author's selection and organization of material have been developed, tested, and refined from his many industry courses and seminars. Five types of broadband circuits are discussed in detail: * Transimpedance amplifiers * Limiting amplifiers * Automatic gain control (AGC) amplifiers * Lasers drivers * Modulator drivers Essential background on optical fiber, photodetectors, lasers, modulators, and receiver theory is presented to help readers understand the system environment in which these broadband circuits operate. For each circuit type, the main specifications and their impact on system performance are explained and illustrated with numerical values. Next, the circuit concepts are discussed and illustrated with practical implementations. A broad range of circuits in MESFET, HFET, BJT, HBT, BiCMOS, and CMOS technologies is covered. Emphasis is on circuits for digital, continuous-mode transmission in the 2.5 to 40 Gb/s range, typically used in SONET, SDH, and Gigabit Ethernet applications. Burst-mode circuits for passive optical networks (PON) and analog circuits for hybrid fiber-coax (HFC) cable-TV applications also are discussed. Learning aids are provided throughout the text to help readers grasp and apply difficult concepts and techniques, including: * Chapter summaries that highlight the key points * Problem-and-answer sections to help readers apply their new knowledge * Research directions that point to exciting new technological breakthroughs on the horizon * Product examples that show the performance of actual broadband circuits * Appendices that cover eye diagrams, differential circuits, S parameters, transistors, and technologies * A bibliography that leads readers to more complete and in-depth treatment of specialized topics This is a superior learning tool for upper-level undergraduates and graduate-level students in circuit design and optical fiber communication. Unlike other texts that concentrate on analog circuits in general or mostly on optics, this text provides balanced coverage of electronic, optic, and system issues. Professionals in the fiber optic industry will find it an excellent reference, incorporating the latest technology and discoveries in the industry.
Download or read book Visible Light Communications written by Zabih Ghassemlooy and published by CRC Press. This book was released on 2017-06-26 with total page 590 pages. Available in PDF, EPUB and Kindle. Book excerpt: Visible Light Communications, written by leading researchers, provides a comprehensive overview of theory, stimulation, design, implementation, and applications. The book is divided into two parts – the first devoted to the underlying theoretical concepts of the VLC and the second part covers VLC applications. Visible Light Communications is an emerging topic with multiple functionalities including data communication, indoor localization, 5G wireless communication networks, security, and small cell optimization. This concise book will be of valuable interest from beginners to researchers in the field.
Download or read book Audio Power Amplifier Design written by Douglas Self and published by Taylor & Francis. This book was released on 2013-07-04 with total page 1293 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is essential for audio power amplifier designers and engineers for one simple reason...it enables you as a professional to develop reliable, high-performance circuits. The Author Douglas Self covers the major issues of distortion and linearity, power supplies, overload, DC-protection and reactive loading. He also tackles unusual forms of compensation and distortion produced by capacitors and fuses. This completely updated fifth edition includes four NEW chapters including one on The XD Principle, invented by the author, and used by Cambridge Audio. Crosstalk, power amplifier input systems, and microcontrollers in amplifiers are also now discussed in this fifth edition, making this book a must-have for audio power amplifier professionals and audiophiles.
Download or read book The Design of CMOS Radio Frequency Integrated Circuits written by Thomas H. Lee and published by Cambridge University Press. This book was released on 2004 with total page 232 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book, first published in 2004, is an expanded and revised edition of Tom Lee's acclaimed RFIC text.
Download or read book High Frequency Integrated Circuits written by Sorin Voinigescu and published by Cambridge University Press. This book was released on 2013-02-28 with total page 921 pages. Available in PDF, EPUB and Kindle. Book excerpt: A transistor-level, design-intensive overview of high speed and high frequency monolithic integrated circuits for wireless and broadband systems from 2 GHz to 200 GHz, this comprehensive text covers high-speed, RF, mm-wave, and optical fibre circuits using nanoscale CMOS, SiGe BiCMOS, and III-V technologies. Step-by-step design methodologies, end-of chapter problems, and practical simulation and design projects are provided, making this an ideal resource for senior undergraduate and graduate courses in circuit design. With an emphasis on device-circuit topology interaction and optimization, it gives circuit designers and students alike an in-depth understanding of device structures and process limitations affecting circuit performance.
Download or read book Application Specific Integrated Circuit ASIC Technology written by Norman Einspruch and published by Academic Press. This book was released on 2012-12-02 with total page 381 pages. Available in PDF, EPUB and Kindle. Book excerpt: Application Specific Integrated Circuit (ASIC) Technology explores and discusses the different aspects of the ASIC technology experienced during the 1990s. The topics of the chapters range from the ASIC business, model, marketing, and development up to its testability, packaging, and quality and reliability. An introductory chapter begins the discussion and tackles the historical perspective and the classification of the ASIC technology. Chapters 2 and 3 cover the business side of the technology as it discusses the market dynamics and marketing strategies. The following chapters focus on the product itself and deal with the design and model and library development. Computer-aided design tools and systems are included in the discussion. Manufacturing and packaging of ASICs are also given attention in the book. Finally, the last three chapters present the application, testability, and reliability of ASIC technology. The text can be of most help to students in the fields of microelectronics, computer technology, and engineering.
Download or read book Advances in Communication Devices and Networking written by Rabindranath Bera and published by Springer Nature. This book was released on 2020-07-27 with total page 502 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers recent trends in the field of devices, wireless communication and networking. It gathers selected papers presented at the International Conference on Communication, Devices and Networking (ICCDN 2019), which was organized by the Department of Electronics and Communication Engineering, Sikkim Manipal Institute of Technology, Sikkim, India, on 9–10 December 2019. Gathering cutting-edge research papers prepared by researchers, engineers and industry professionals, it will help young and experienced scientists and developers alike to explore new perspectives, and offer them inspirations on how to address real-world problems in the areas of electronics, communication, devices and networking.
