Download or read book Additive and Subtractive Manufacturing of Composites written by Sanjay Mavinkere Rangappa and published by Springer Nature. This book was released on 2021-08-06 with total page 255 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book describes crucial aspects related to the additive and subtractive manufacturing of different composites. The first half of this book mainly deals with the various types of composite fabrication methods along with the introduction, features and mechanisms and also the processing of composite materials via additive manufacturing route. Also, the thermal, mechanical, physical and chemical properties relevant to the processing of composite materials are included in the chapters. The second half of this book primarily demonstrates an extensive section on the different types of additive manufacturing processes like selective laser sintering, selective laser melting, stereolithography, fused deposition modeling and material jetting used to fabricate the metals and polymers. Also, the chapters address the complete description of fabrication processes for metal matrix composites and polymer matrix composites. Moreover, the different methods adopted such as short peening, micro-machining, heat-treatment and solution treatment to improve the surface improvement are well discussed. This book gives many helps to researchers and students in the fields of the additive and subtractive manufacturing of different composites.

Download or read book Proceedings of the 3rd Conference on Physical Modeling for Virtual Manufacturing Systems and Processes written by Jan C. Aurich and published by Springer Nature. This book was released on 2023-07-10 with total page 305 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is an open access book reporting the results of nine years research of the International Research Training Group (IRTG) 2057, funded by the German Research Foundation (DFG). The IRTG is a joint venture between the TU Kaiserslautern, the University of California Berkeley, and University of California Davis. The book is content-driven mainly by two disciplines: engineering and computer science. Through the application of scientific knowledge and advanced computer-based methods in conjunction with physical models on a level unrealized in the past, technologies and methods are promoted, which can be used for planning and optimization of manufacturing systems and processes. As a result, fundamental understanding as well as extensive systems, tools and computational algorithms, which significantly improve the integration of advanced computational methods for solving problems of manufacturing systems and processes will be available. This open access book is of interest to any researcher dealing with process and factory planning in manufacturing, like for cutting and additive manufacturing.

Download or read book Fundamentals of Laser Powder Bed Fusion of Metals written by Igor Yadroitsev and published by Elsevier. This book was released on 2021-05-23 with total page 678 pages. Available in PDF, EPUB and Kindle. Book excerpt: Laser powder bed fusion of metals is a technology that makes use of a laser beam to selectively melt metal powder layer-by-layer in order to fabricate complex geometries in high performance materials. The technology is currently transforming aerospace and biomedical manufacturing and its adoption is widening into other industries as well, including automotive, energy, and traditional manufacturing. With an increase in design freedom brought to bear by additive manufacturing, new opportunities are emerging for designs not possible previously and in material systems that now provide sufficient performance to be qualified in end-use mission-critical applications. After decades of research and development, laser powder bed fusion is now enabling a new era of digitally driven manufacturing. Fundamentals of Laser Powder Bed Fusion of Metals will provide the fundamental principles in a broad range of topics relating to metal laser powder bed fusion. The target audience includes new users, focusing on graduate and undergraduate students; however, this book can also serve as a reference for experienced users as well, including senior researchers and engineers in industry. The current best practices are discussed in detail, as well as the limitations, challenges, and potential research and commercial opportunities moving forward. - Presents laser powder bed fusion fundamentals, as well as their inherent challenges - Provides an up-to-date summary of this advancing technology and its potential - Provides a comprehensive textbook for universities, as well as a reference for industry - Acts as quick-reference guide

Download or read book Bioimplants Manufacturing written by Abhilash P M and published by CRC Press. This book was released on 2024-09-04 with total page 331 pages. Available in PDF, EPUB and Kindle. Book excerpt: The text covers fundamentals and technological advancements in processing, post-processing, and surface engineering of bioimplant materials. It further discusses important topics such as the additive manufacturing of bioimplants, the tribological performance of bioimplants, and the hybrid and non-traditional manufacturing of bioimplants materials. The text also presents the latest advancements in intelligent bioimplant manufacturing using artificial intelligence and machine learning. This book: Offers an in-depth understanding of the fundamentals, types, materials and applications of bioimplants Highlights the effect of processing on microstructure, biocompatibility, and mechanical behavior of bioimplants Investigates the surface modification methods and tribological performance of bioimplants Discusses additive manufacturing and non-traditional manufacturing techniques such as electrical discharge machining and electrochemical machining of bioimplants materials Covers smart technologies such as artificial intelligence and machine learning-based intelligent implant manufacturing for Industry 4.0 It is primarily written for senior undergraduate and graduate students and academic researchers in the fields of mechanical engineering, biomedical engineering, production engineering, industrial engineering, aerospace engineering, and manufacturing engineering.

Download or read book Sintering Techniques of Materials written by Arunachalam Lakshmanan and published by BoD – Books on Demand. This book was released on 2015-04-01 with total page 202 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book covers new sintering techniques on ceramic materials, metals and composites as well as reprocessed PTFE. The book covers theoretical as well as experimental aspects on Spark Plasma Sintered (SPS) Porous copper, development of cutting blades with high hardness and resistance to cracking and wear, increased microhardness of austenitic steel ? TiB2 composites obtained with high pressure - high temperature sintering, Al2O3 porous body with cotton as the template and excellent thermal insulation with direct application for refractories as well as Metal matrix composites added nanostructured tantalum carbide and an overview of different sintering techniques used in powder metallurgy. Finally recycling of PTFE scrap materials using ram extrusion and compression molding is described.

Download or read book High Entropy Materials Theory Experiments and Applications written by Jamieson Brechtl and published by Springer Nature. This book was released on 2022-01-03 with total page 776 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book discusses fundamental studies involving the history, modelling, simulation, experimental work, and applications on high-entropy materials. Topics include data-driven and machine-learning approaches, additive-manufacturing techniques, computational and analytical methods, such as density functional theory and multifractal analysis, mechanical behavior, high-throughput methods, and irradiation effects. The types of high-entropy materials consist of alloys, oxides, and ceramics. The book then concludes with a discussion on potential future applications of these novel materials.

Download or read book Laser Additive Manufacturing of High Performance Materials written by Dongdong Gu and published by Springer. This book was released on 2015-04-21 with total page 322 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book entitled “Laser Additive Manufacturing of High-Performance Materials” covers the specific aspects of laser additive manufacturing of high-performance new materials components based on an unconventional materials incremental manufacturing philosophy, in terms of materials design and preparation, process control and optimization and theories of physical and chemical metallurgy. This book describes the capabilities and characteristics of the development of new metallic materials components by laser additive manufacturing process, including nanostructured materials, in situ composite materials, particle reinforced metal matrix composites, etc. The topics presented in this book, similar as laser additive manufacturing technology itself, show a significant interdisciplinary feature, integrating laser technology, materials science, metallurgical engineering and mechanical engineering. This is a book for researchers, students, practicing engineers and manufacturing industry professionals interested in laser additive manufacturing and laser materials processing. Dongdong Gu is a Professor at College of Materials Science and Technology, Nanjing University of Aeronautics and Astronautics (NUAA), PR China.

Download or read book Titanium in Medical and Dental Applications written by Francis Froes and published by Woodhead Publishing. This book was released on 2018-05-09 with total page 656 pages. Available in PDF, EPUB and Kindle. Book excerpt: Titanium in Medical and Dental Applications is an essential reference book for those involved in biomedical materials and advanced metals. Written by well-known experts in the field, it covers a broad array of titanium uses, including implants, instruments, devices, the manufacturing processes used to create them, their properties, corrosion resistance and various fabrication approaches. Biomedical titanium materials are a critically important part of biomaterials, especially in cases where non-metallic biomedical materials are not suited to applications, such as the case of load-bearing implants. The book also covers the use of titanium for implants in the medical and dental fields and reviews the use of titanium for medical instruments and devices. - Provides an understanding of the essential and broad applications of Titanium in both the medical and dental industries - Discusses the pathways to manufacturing titanium into critical biomedical and dental devices - Includes insights into further applications within the industry

Download or read book Laser Additive Manufacturing written by Milan Brandt and published by Woodhead Publishing. This book was released on 2016-09-01 with total page 500 pages. Available in PDF, EPUB and Kindle. Book excerpt: Laser Additive Manufacturing: Materials, Design, Technologies, and Applications provides the latest information on this highly efficient method of layer-based manufacturing using metals, plastics, or composite materials. The technology is particularly suitable for the production of complex components with high precision for a range of industries, including aerospace, automotive, and medical engineering. This book provides a comprehensive review of the technology and its range of applications. Part One looks at materials suitable for laser AM processes, with Part Two discussing design strategies for AM. Parts Three and Four review the most widely-used AM technique, powder bed fusion (PBF) and discuss other AM techniques, such as directed energy deposition, sheet lamination, jetting techniques, extrusion techniques, and vat photopolymerization. The final section explores the range of applications of laser AM. - Provides a comprehensive one-volume overview of advances in laser additive manufacturing - Presents detailed coverage of the latest techniques used for laser additive manufacturing - Reviews both established and emerging areas of application

Download or read book Selective Laser Melting Materials and Applications written by Prashanth Konda Gokuldoss and published by . This book was released on 2020 with total page 98 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive manufacturing (AM) is one of the manufacturing processes that warrants the attention of industrialists, researchers, and scientists. AM has the ability to fabricate materials to produce parts with complex shapes without any theoretical restrictions combined with added functionalities. Selective laser melting (SLM), also known as laser-based powder bed processing (LPBF), is one of the main AM process that can be used to fabricate wide variety of materials that are Al-, Ti-, Fe-, Ni-, Co-, W-, Ag-, and Au-based, etc. However, several challenges need to be addressed systematically, such as development of new materials that suit the SLM process conditions so the process capabilities can be fully used to produce new properties in these materials. Other issues in the field are the lack of microstructure-property correlations, premature failure, etc. Accordingly, this Special Issue (book) focuses mainly on the microstructure-correlation in three different alloys: AlSi10Mg, Ti6Al4V, and 304L stainless steel, where six articles are presented. Hence, this Special Issue outlines microstructure-property correlations in the SLM processed materials and provides a value addition to the field of AM.

Download or read book Additive Manufacturing Volume 2 written by Prashanth Konda Gokuldoss and published by MDPI. This book was released on 2020-04-15 with total page 351 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive manufacturing (AM) is one of the manufacturing processes that warrants the attention of industrialists, researchers and scientists, because of its ability to produce materials with a complex shape without theoretical restrictions and with added functionalities. There are several advantages to employing additive manufacturing as the primary additive manufacturing process. However, there exist several challenges that need to be addressed systematically. A couple such issues are alloy design and process development. Traditionally alloys designed for conventional cast/powder metallurgical processes were fabricated using advanced AM processes. This is the wrong approach considering that the alloys should be coined based on the process characteristics and meta-stable nature of the process. Hence, we must focus on alloy design and development for AM that suits the AM processes. The AM processes, however, improve almost every day, either in terms of processing capabilities or processing conditions. Hence, the processing part warrants a section that is devoted to these advancements and innovations. Accordingly, the present Special Issue (book) focuses on two aspects of alloy development and process innovations. Here, 45 articles are presented covering different AM processes including selective laser melting, electron beam melting, laser cladding, direct metal laser sintering, ultrasonic consolidation, wire arc additive manufacturing, and hybrid manufacturing. I believe that this Special Issue bears is vital to the field of AM and will be a valuable addition.

Download or read book Titanium Powder Metallurgy written by Ma Qian and published by Butterworth-Heinemann. This book was released on 2015-02-10 with total page 649 pages. Available in PDF, EPUB and Kindle. Book excerpt: Titanium Powder Metallurgy contains the most comprehensive and authoritative information for, and understanding of, all key issues of titanium powder metallurgy (Ti PM). It summarizes the past, reviews the present and discusses the future of the science and technology of Ti PM while providing the world titanium community with a unique and comprehensive book covering all important aspects of titanium powder metallurgy, including powder production, powder processing, green shape formation, consolidation, property evaluation, current industrial applications and future developments. It documents the fundamental understanding and technological developments achieved since 1937 and demonstrates why powder metallurgy now offers a cost-effective approach to the near net or net shape fabrication of titanium, titanium alloys and titanium metal matrix composites for a wide variety of industrial applications. - Provides a comprehensive and in-depth treatment of the science, technology and industrial practice of titanium powder metallurgy - Each chapter is delivered by the most knowledgeable expert on the topic, half from industry and half from academia, including several pioneers in the field, representing our current knowledge base of Ti PM. - Includes a critical review of the current key fundamental and technical issues of Ti PM. - Fills a critical knowledge gap in powder metal science and engineering and in the manufacture of titanium metal and alloys

Download or read book Additive Manufacturing of Metals written by John O. Milewski and published by Springer. This book was released on 2017-06-28 with total page 351 pages. Available in PDF, EPUB and Kindle. Book excerpt: This engaging volume presents the exciting new technology of additive manufacturing (AM) of metal objects for a broad audience of academic and industry researchers, manufacturing professionals, undergraduate and graduate students, hobbyists, and artists. Innovative applications ranging from rocket nozzles to custom jewelry to medical implants illustrate a new world of freedom in design and fabrication, creating objects otherwise not possible by conventional means. The author describes the various methods and advanced metals used to create high value components, enabling readers to choose which process is best for them. Of particular interest is how harnessing the power of lasers, electron beams, and electric arcs, as directed by advanced computer models, robots, and 3D printing systems, can create otherwise unattainable objects. A timeline depicting the evolution of metalworking, accelerated by the computer and information age, ties AM metal technology to the rapid evolution of global technology trends. Charts, diagrams, and illustrations complement the text to describe the diverse set of technologies brought together in the AM processing of metal. Extensive listing of terms, definitions, and acronyms provides the reader with a quick reference guide to the language of AM metal processing. The book directs the reader to a wealth of internet sites providing further reading and resources, such as vendors and service providers, to jump start those interested in taking the first steps to establishing AM metal capability on whatever scale. The appendix provides hands-on example exercises for those ready to engage in experiential self-directed learning.

Download or read book Titanium and Titanium Alloys written by Christoph Leyens and published by John Wiley & Sons. This book was released on 2006-03-06 with total page 532 pages. Available in PDF, EPUB and Kindle. Book excerpt: This handbook is an excellent reference for materials scientists and engineers needing to gain more knowledge about these engineering materials. Following introductory chapters on the fundamental materials properties of titanium, readers will find comprehensive descriptions of the development, processing and properties of modern titanium alloys. There then follows detailed discussion of the applications of titanium and its alloys in aerospace, medicine, energy and automotive technology.

Download or read book Additively Manufactured Inconel 718 written by Dunyong Deng and published by Linköping University Electronic Press. This book was released on 2018-01-24 with total page 82 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive manufacturing (AM), also known as 3D printing, has gained significant interest in aerospace, energy, automotive and medical industries due to its capabilities of manufacturing components that are either prohibitively costly or impossible to manufacture by conventional processes. Among the various additive manufacturing processes for metallic components, electron beam melting (EBM) and selective laser melting (SLM) are two of the most widely used powder bed based processes, and have shown great potential for manufacturing high-end critical components, such as turbine blades and customized medical implants. The futures of the EBM and SLM are doubtlessly promising, but to fully realize their potentials there are still many challenges to overcome. Inconel 718 (IN718) is a nickel-base superalloy and has impressive combination of good mechanical properties and low cost. Though IN718 is being mostly used as a turbine disk material now, the initial introduction of IN718 was to overcome the poor weldability of superalloys in 1960s, since sluggish precipitation of strengthening phases ?’/?’’ enables good resistance to strain-age cracking during welding or post weld heat treatment. Given the similarity between AM and welding processes, IN718 has been widely applied to the metallic AM field to facilitate the understandings of process-microstructure-property relationships. The work presented in this licentiate thesis aims to better understand microstructures and mechanical properties EBM and SLM IN718, which have not been systematically investigated. Microstructures of EBM and SLM IN718 have been characterized with scanning electron microscopy (SEM), transmission electron microscopy (TEM) and correlated with the process conditions. Monotonic mechanical properties (e.g., Vickers microhardness and tensile properties) have also been measured and rationalized with regards to the microstructure evolutions before and after heat treatments. For EBM IN718, the results show the microstructure is not homogeneous but dependant on the location in the components, and the anisotropic mechanical properties are probably attributed to alignment of porosities rather than texture. Post heat treatment can slightly increase the mechanical strength compared to the as-manufactured condition but does not alter the anisotropy. SLM IN718 shows significantly different microstructure and mechanical properties to EBM IN718. The as-manufactured SLM IN718 has very fine dendritic microstructure and Laves phases in the interdendrites, and is “work-hardened” by the residual strains and dislocations present in the material. Mechanical properties are different between horizontally and vertically built samples, and heat treatment can minimize this difference. Results from this licentiate thesis provide the basis for the further research on the cyclic mechanical properties of EBM and SLM IN718, which would be the focus of following phase of the Ph.D. research.

Download or read book Powder Metallurgy of Titanium written by Ma Qian and published by Trans Tech Publications Ltd. This book was released on 2012-08-24 with total page 367 pages. Available in PDF, EPUB and Kindle. Book excerpt: Powder Processing, Consolidation and Metallurgy of Titanium Selected, peer reviewed papers from the Symposium on Powder Processing and Metallurgy of Titanium, December 4-7, 2011, Brisbane, Australia

Download or read book Light Metal Alloys Applications written by Waldemar Alfredo Monteiro and published by BoD – Books on Demand. This book was released on 2014-06-11 with total page 254 pages. Available in PDF, EPUB and Kindle. Book excerpt: Lightweight alloys have become of great importance in engineering for construction of transportation equipment. At present, the metals that serve as the base of the principal light alloys are aluminum and magnesium. One of the most important lightweight alloys are the aluminum alloys in use for several applications (structural components wrought aluminum alloys, parts and plates). However, some casting parts that have low cost of production play important role in aircraft parts. Magnesium and its alloys are among the lightest of all metals and the sixth most abundant metal on earth. Magnesium is ductile and the most machinable of all metals. Many of these light weight alloys have appropriately high strength to warrant their use for structural purposes, and as a result of their use, the total weight of transportation equipment has been considerably decreased.